Search Documents

By Michael F. Roach, Joseph K. Cavey, Gary E. Taylor

A rigorous horizontal drilling and chemical grouting program was specified beneath the Hollywood Freeway (U.S. Route 101) section of Los Angeles Metrorail Contract C-311.Twin 6.67-m (22-ft.) diameter starter tunnels were to be conventionally mined through amixed alluvial and bedrock face consisting of silty sand, gravel, and weathered sandstone and siltstone of the Topanga Group. The contact between the alluvium and bedrock dipped toward the Crossover Excavation where the horizontal drilling and grouting operations were performed. The intent of this grouting program was to stabilize the mixed face to minimize ground loss and surface settlement, and to reduce groundwater inflow into the tunnel headings. Given the highly variable mixed face conditions, horizontal drilling up to 86 m (284 ft.) resulted in upward trending trajectories which likely followed the bedrock contact. Chemical grouting was performed in a primary, secondary and tertiary, three dimensional sequence. Evaluation of the primary and secondary grouting parameters indicated where tertiary grouting was required. Grouting pressures induced a small rock failure at the tunnel heading as well as increased stresses on the tiebacks of the excavation.

Jan 1, 1997

By Kazem Oraee

In underground coal mining, particularly room-and-pillar methods, the coal pillars play a significant role in roof stability. If the pillar dimensions are increased, the pillar bearing capacity also increases, but more coal remains in the pillar and therefore the recovery of mining operation decreases. Therefore, determining the optimum pillar dimension based on technical, economical and performance parameters is important. In this paper, the coal pillar is designed by using the concept of ground reaction curve (GRC). For this purpose, the GRC for coal pillars is drawn and then the elastic and plastic zone of coal pillar behavior is determined. Based on elastic and plastic zone, different equations are presented to draw a pillar reaction curve and the process of coal pillar design based on GRC is explained. As a case study, this new technique is applied to study the coal pillar state in Tabas coal mine of Iran. The results show that the presented new approach is successfully used in the design of the optimum coal pillar dimensions, and also determines the elastic and plastic behavior limit, which is important especially for the logical design of yield pillars.

Jan 1, 2009

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and thus deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the go band to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Feb 27, 2013

By H. Y. Sohn, R. D. Hagni, M. K. Kojo

Reflected light microscopy was used to study the mineralogy and textures of experimental reactions of a nickel concentrate with a slag. Such an interaction is an important step in the bath smelting of nickel sulfide concentrate. Concentrate particles in the central portions of the pellets are rounded and develop vermicular SO2 gas porosity. In the outer portions of the pellets, the original minerals of the concentrate, pyrrhotite, pentlandite, pyrite, chalcopyrite, and violarite have agglomerated and reacted to form two intergrown phases: 1) pyrrhotite solid solution (Fe0.75Ni0.18Cu0.01S) and pentlandite solid solution (Fe0.58Ni0.51Cu0.03S). Magnetite formed euhedral crystals, skeletal crystals, and dendrites at the margins of the matte. Prismatic ferrohypersthene and octahedral Mg-Al-Fe spinel crystals and dendrites are present in the glassy slag.

Jan 1, 2001

By J. Noll

Many underground metal/nonmetal mines are using enclosed cabs on mining equipment to reduce the exposure of miners to diesel particulate matter (DPM). However, some enclosed cab systems may not be meeting their expected efficiency in capturing DPM, which could be a result of inappropriate filter use, cab leaks, or insufficient pressurization. NIOSH investigated several types of filters for reducing DPM to determine which type had the best capture efficiency. The laboratory results indicated that a MERV 8 (Minimum Efficiency Reporting Value, as defined by the American Society of Heating, Refrigerating and Air- Conditioning Engineers) filter captured about 50 percent of the DPM, a MERV 16 filter collected 96-98 percent of the DPM, and two HEPA (high efficiency particulate air) grade filters captured over 99 percent of the DPM. NIOSH also performed a field study to measure the efficiency of two cabs at a limestone mine. The cab filtration systems of a loader and haul truck were found to be over 90 percent effective in removing DPM except under certain operating conditions when the efficiency was as low as 41 percent. Evidence seems to suggest that these conditions were when a window was open in the cab.

Jan 1, 2011

By Brett Campbell

The San Vicente to 2nd Aqueduct Pipeline?Tunnel project is a raw water conveyance tunnel linking the San Vicente Reservoir (SVR) to the 2nd Aqueduct Pipeline via Rancho Penasquitos Pressure Control Facility (RPPCF). This 58,230 lf long tunnel will be 8.5? final ID, and has four points of construction access. The job is classified into 6 Reaches of tunnel, identified by the dominant geology within the reach. This paper will focus on Reach 3, specifically the measures necessary to drill and blast a 550 lineal foot section of granitic rock tunnel immediately in front of an open face digger shield.

Jan 1, 2008

By William R. Yernberg

The 2006 North American Tunneling (NAT) Conference was held June 10-15, 2006, in Chicago, IL. The biennial conference was the first NAT conference by the newly formed Underground Construction Association of SME (UCA of SME). The UCA of SME was formed earlier this year at the request of members of the American Underground Association (AUA) (ME, April 2006, page 75). The conference included a keynote session, technical programs, workshops, a trade show and social activities. The conference exceeded expectations with 570 attendees. They included engineers, equipment manufacturers, representatives from government agencies and other interested individuals in the underground construction industry. The trade show was also a success with more than 86 booth spaces sold. Vendors included the biggest names in the underground construction and tunneling industry and included equipment manufactures, construction contractors and engineering companies. The trade exhibition provided a forum for interested parties in the tunneling industry to meet and discuss services, equipment and techniques.

Jan 1, 2006

By Michael Taylor, Thomas W. BoBo

Currently two of the most important characteristics of construction aggregates are (a) the particle size distribution (psd) and (b) the “shape” of the aggregate particles. The long established test methods and standards for these properties require substantial resources and most suppliers can take samples and conduct tests at intervals measured in days (psd) or even months (shape). Furthermore these tests require time: so the results are available only after material has been stockpiled or shipped. In the rare cases where problems are found the out-of-spec material has often been shipped to points unknown. There are substantial advantages to be obtained if the psd and other geometrical properties could be obtained from the material as it moves through the production processes and if the results could be reported back within seconds or minutes to Plant Control Managers. This paper describes a single on-line system used to evaluate production of crushed material in a production quarry. The system consists of an enclosure (containing the camera and lighting etc.) mounted over a production belt. Images are fed by fiber optic cable to a nearby control room where the data are analyzed; stored; displayed; and made available for integration into a process control system. Numerous forms of display can be created according to the needs of the producer. Once programmed by an automation engineer all functions of operation are fully automated. The system has permitted over 400 tests per hour with a feed back time less than 2 seconds. Sufficient geometrical measurements are made so that many different “shape” factors can be computed on a similar time scale. The paper summarizes the results from approximately 100 shifts of about 8 hours each and compares the imaging method with the current standard hand methods. Study of the data generated showed that, when combined with additional plant information, the system can be used to generate additional useful control information.

Jan 1, 2005

By R. J. Hickson

From 1993 through 1999 Cyprus Amax Minerals Company successfully completed eight major construction projects around the world. Six greenfield mines were brought into production, an ongoing operation was completely modernized, and an environmental issue was appropriately remediated. The projects stretched over three continents, from arctic Russia to the Atacama Desert, from 16,000feet to sea level, from city suburbs to remote wilderness, from a low of $130 million to over $1 billion. Open pit and underground; mill and leach; gold, copper, molybdenum, and coal were all encompassed. The breadth of diversity experience from these projects inspired Cyprus Amax to create a “best practices” project management protocol, to steer corporate expansion into the next millenium. This paper summarizes those best practices, while high-lighting project management pitfalls to avoid.

Jan 1, 2000

By J. Davies

This paper describes the successful management and construction of the 5.18 m (17 ft) diameter, segmentally lined, North Dorchester Bay CSO storage tunnel in Boston, MA. This 3,300 m (10,830 ft) long tunnel was mined through variable soft ground with only 6 m (20 ft) of cover, using an earth pressure balance tunnel boring machine. These extensive data collected from the projects unique automated and internet accessible geotechnical and TBM monitoring system, will be examined and used to explore the relationships between geological conditions, TBM operating parameters and measured settlements. The paper will also discuss the use of screw revolutions as an indicator of muck volume.

By Chaoxun Zhao, Daniel Tao, Craig Blue, Narendra B. Dahotre, Rick Honaker, Bhupendra K. Parekh, Hongyang Han

Equipment wear and corrosion have significant adverse impacts on the operating cost and efficiency of mineral processing plants. In this project advanced surface enhancement technologies are being investigated to decrease the wear and corrosion rate of metal surface. Enhanced metal surfaces are achieved through surface conversion, enrichment, and coating by use of advanced High-Density Infrared (HDI) and other technologies. Studies have been done to determine the effects of process parameters on surface properties and identify optimum conditions. The microstructure of the enhanced metal surfaces was characterized by SEM, EDS, and microindentation. Laboratory wear testing was carried out to investigate the wear performance and the viable coating candidate was determined.

Jan 1, 2005

Federal regulations require the use of methane monitors on all mining machines. All machine-mounted methane monitors currently used in underground coal mines rely on catalytic heat of combustion sensors. As a comparison, although not currently approved for use on underground mining equipment, instruments with infrared sensors are evaluated in this study. Potential advantages of using infrared sensors include faster response time, long-term stability, and reduced maintenance needs. Tests conducted in the laboratory and at a full-scale model mine compare the performance of catalytic heat of combustion and infrared sensors operating under test conditions designed to simulate airflow conditions underground.

Jan 1, 2009

By Robert Schnab

ASFINAG is responsible for the construction and operation of the Austrian highway system. It is approx. 2,400 km of highways and 65 tunnels with a total length of 200 km including the Tauern Tunnel. In order to improve the documentation of the tunnel construction, ASFINAG chose to use a state of the art tunnel scanning system to record the various stages of construction: excavation, initial shotcrete lining, smoothing layer and final cast in place concrete lining. The geometric and photogrammetric documentation is provided on a daily basis to all par-ties involved. This innovative concept provides accurate & complete information in real time. The tunnel scanner documentation of the 2nd tube at the 6.4 km long Tauern Tunnel will be presented in this paper as a part of the survey contract.

By Dexter C. Hatch

At MacIntyre Development of the National Lead Company, Taha s, New York,, the flotation plant was set up to recover ilmenite from the finer size fraction of the ore that cannot be efficiently treated in the main gravity-magnetic separa¬tion process. It was later expanded to handle the reground middlings from the tables wetherill magnetic separators. The ilmenite-magnetite ore is ground to minus 20 mesh in five 6 x 12 ft. rod mills in closed circuit with DSM screens. The minus 20 mesh screen undersize is pumped to four parallel sections each consisting of two rougher wet-magnetic separators and one cleaner separator for magnatite removal. The screen undersize from the fifth section is distributed to all four sections. The magnetite removed in the roughers is pumped back to the cleaners and the cleaner magnetite is dewatered in rake classifiers and carried by belt to the winter plant or the stockpile area. The nonmagnetic sands from rougher and cleaner magnetic separator are sized for table feed in eight pocket hydraulic sizers. The slime overflows from the Crocketts, the sizers, and the magnetite rakes are collected and pumped to three-inch cyclones for thickening and desliming. The cyclone underflow is the principal flotation plant feed.

Jan 1, 1962

By B. Slaker

The ability to detect and quantify ground movements in underground mine workings is of the utmost importance to the safety of miners and continuity of operations. Rib sloughage is one of the most common forms of underground deformations. Remote sensing techniques, such as laser scanning, can be used to quantify this rib sloughage, by recording precise, time-lapse point clouds of mine workings. In order to determine sloughage volumes and locations, a total of 11 laser scans were performed 41 days apart at a working section of an underground limestone mine. During this period, significant sloughing and scaling occurred, allowing for differentiation between the initial and final point clouds.

Feb 27, 2013

By Jeffrey Mitsopoulos

King County?s (KC) Brightwater Conveyance Project in Seattle, Washington involves the construction of approximately 21 kilometers (13 miles) of bored tunnel, in three contracts, with four TBM?s which produce large amounts of real-time digital mining data. To facilitate the management of TBM data with a single interface and assist in project Quality Assurance, KC?s Construction Manager (Jacobs Engineering) recommended the use of the software TPC (Tunneling Process Control), developed by Babendererde Engineers GmbH. The paper demonstrates how TPC was used for oversight, analysis and QA on a complex tunneling project and how contemporaneous review and management of data results in a better understanding of TBM performance than can be obtained by retrospective analysis of data.

By Amanda Elioff

Success of the Gold Line Eastside Extension rail tunnels in Los Angeles has prompted Metro?s planning for two new rail lines to include underground alternatives. The Westside Extension Transit Corridor alternatives include up to 17 miles of subway to be constructed in soft ground. The routes will require construction in Los Angeles? ?Potential Methane Zone,? not considered for subway construction until recently. Slurry face TBMs will likely be specified. The Regional Connector, through the downtown area, includes one underground alternative with 1.7 miles of tunnel as well as three underground stations in soft ground and rock. Challenges will include tunnel and station construction under narrow streets. This paper will describe the alternatives, planning, geologic conditions and tunneling concepts for both planning studies.

By James F. Kvitkovich, George V. Weisdack

Longwall mining techniques were introduced into U.S. bituminous coal mining operations in the early 1960s. These techniques were gradually adopted by many mines during the 1970s. By 1983, considered to be the peak of the longwall mine census, there were 118 active longwall faces in 79 coal mines throughout the United States. Beginning in 1984, longwall faces began a decline in numbers that has continued to the present day (Fig. 1). The geographic distribution of longwall faces today is shown in Fig.2 according to region. A breakdown of recent longwall mine production by region is shown in Table 1. An approximate breakdown of present longwall face installations by product (metallurgical and steam) is shown in Table 2.

Jan 1, 2005

Once every three years the eyes of the construction and mining industry?s turn to Munich, Germany for the bauma trade fair and exhibition. From April 19-25, Messe München International (MMI) will host the 29th edition of this massive show that, despite the recent recession and global financial struggles, has grown yet again. The show, which is completely booked, will take place on a record 555,000 m2 (5.9 million sq ft) of indoor and outdoor exhibition space at the New Munich Trade Fair Centre. More than 3,000 exhibitors are expected to make use of this event. To prepare for the show that highlights some of the largest and most impressive construction and mining equipment in the world, Messe München began working months in advance on getting the infrastructure on the open-air site ready, in time for the arrival of the gigantic machinery exhibits, which started to arrive in March. Part of the preparations include a new entrance at the northwest corner of the exhibition center that was built to regulate visitor flow better. This should help with bauma considering that in 2007 more than 500,000 visitors passed through the gates. ?Although in 2010 the construction machinery sector in many markets worldwide will be recovering only slowly from the recession, we are pleased to report that we are seeing strong demand for exhibition space. This shows that exhibitors regard participation in the world?s leading trade fair bauma as a must, although many are at present having to make cuts in their advertising and trade-fair budgets. We have been particularly surprised by the strong demand for space from exhibitors from markets like China, India and Turkey. The fair is fully booked and many more companies are on the waiting list,? said Eugen Egetenmeir, managing director of Messe München. More than 50 percent of the exhibitors at bauma 2010 come from countries outside of Germany. While the show?s primary focus is on the construction section, it is not as if the mining sector will be difficult to find. With some of the largest equipment in world on display in section C2 (Fig. 1), the mining industry is sure to be well-represented.

Jan 4, 2010

By R. E. Ray

Compared to conventional fully ducted axial and centrifugal fan systems, jet fans can offer a number of advantages for control of smoke during fire emergencies and dilution of diesel engine exhaust products in vehicular and rail tunnels. The success of jet fan applications is the result of a balance between the temperature de-rating of the fan, buoyancy forces and the installation momentum transfer efficiency. This paper provides a case study of a unique application of vertically-mounted jet fans in ventilation shafts used to provide both emergency ventilation and pollution control for an overbuild created by the construction of a series of commercial high-rise residential buildings over a portion of an existing passenger rail line. A detailed evaluation of a set of shafts for one building is presented, including a discussion of the calculation methods used to estimate the required jet fan capacity and the results of the subsequent numerical analysis using Computational Fluid Dynamics to simulate the performance of the jet fans during train car fire emergencies.

Jan 1, 2009