Search Documents

By D Reddy

Rosh Pinah Zinc Corporation is a zinc-lead mine located in southern of Namibia. It is currently considering the development of a low grade ore body containing about 2.8% zinc. This ore can be utilised by the concentrator if it could be upgraded prior to the ball mill. Preliminary work indicated that the ore may be upgraded in a pre-beneficiating stage by using dense medium separation, X-ray sorting or a combination thereof to a feed grade of minimum 9% zinc. This paper describes the process followed in evaluating the technologies for pre-beneficiation. The results from test work indicated that the low grade ore is amenable to pre-beneficiation by both dense medium separation and X-ray sorting. A comparison between the two technologies showed that dense medium separation marginally outperformed X-ray sorting on grade and recovery. The results for the X-ray sorting were achieved by tuning the calibration curve specifically for the samples tested.

Jan 1, 2008

By M. W. Hildyard

A blast was engineered close to a tunnel in a deep-level mine with the purpose of studying the wave interaction with the tunnel. Numerical modelling of seismic wave propagation was used in both the forward planning and the back-analysis of this experiment. This paper presents the forward analysis. A likely model for a propagating blast was investigated and developed. This model predicts the influence of the velocity of detonation of the blast and the rise-time of the blast on the radiation pattern, and hence on the expected positions of maximum velocity at the tunnel surface. An attempt was made to quantify the parameters of the blast model, using waveform data from two other blast experiments. The blast model caused particle velocities which were an order of magnitude lower than these measured velocities. Large values for blast pressure were required to match the amplitudes of the recorded velocities. An alternative ?effective? source with a similar mechanism but increased diameter was proposed to account for the higher velocities. It was established that distant velocities scale with the square of the borehole diameter. A calibration blast at the experimental site was also modelled. Agreement in the waveforms was not sufficient for conclusive statements to be made about the validity of the source model. However, the modelled waveforms show an encouraging correspondence with some measured waveforms. This gave confidence that the model could be used to examine wave propagation around the tunnel, and allowed a scaled source to be developed for forward analysis of the main experiment.

Jan 1, 2001

By M. L. Bakker

The ISASMELT? top submerged lance (TSL) bath smelting process was developed in Mount Isa, Australia by Mount Isa Mines Limited (now a subsidiary of Xstrata plc) during the 1980s. By the end of 2011, the total installed capacity of the ISASMELT? technology will exceed 8 000 000 metric tons per year of feed materials in copper and lead smelters around the world. Commercial plants, operating in Belgium and Germany, are also batch converting copper materials in ISASMELT? furnaces. This TSL technology is equally effective for continuous converting processes, in which role it is called ISACONVERT?. This paper presents the recently patented ISACONVERT? process for the continuous converting of nickel and platinum group metal (PGM) containing mattes using the calcium ferrite slag system. The paper focuses on the potential application of the ISACONVERT? technology to existing nickel and PGM smelting complexes.

Jan 1, 2011

By J. L. Fuentes-Cantillana, Á. Rodríguez, P. Morillo

Evacuation operations from work places in the case of an emergency are the key to minimising the effects of catastrophic type accidents such as fires, explosions, cave-ins, floods, etc. The correct planning of these operations, having the necessary means for sounding alarms and communicating and suitable training of personnel are the key factors for guaranteeing successful evacuation. The article gives an analysis of the problem in the case of subterranean mining and various types of work developed by AITEMIN in this field, including the development of new alarm and communication means specially adapted to the characteristics of mining operations, development of tools for help in the preparation of emergency plans and experiences in the education and training of personnel.

Jan 1, 2003

By G. A. Bezuidenhout, J. P. T. Kapusta, D. K. Chibwe

"Peirce-Smith converters (PSCs) are extensively used in the copper, nickel, and platinum group metals industries. The typical converting operation involves lateral purging of air into molten matte through a bank of tuyeres. This blowing operation occurs at low pressure from the blowers, resulting in a bubbling regime that is considered inefficient from both a process and an energy utilization perspective. Inherent drawbacks also include recurrent tuyere blockage, tuyere punching, and low oxygen efficiency.Western Platinum embarked on a full-scale industrial evaluation of generating a jetting regime by using sonic injection. Prior to industrialscale tests, a numerical assessment to ascertain the feasibility of implementing sonic injection into a PSC was conducted. The work included flow characterization at high-pressure injection achieving sonic velocity at the tuyere exit. The 2D and 3D simulations of the three-phase system were carried out using the volume of fluid method together with the RKE turbulence model to account for the multiphase and turbulent nature of the flow.This paper discusses the key findings in understanding plume extension, velocity distribution, shear wall stress analysis, and phase distribution characteristics in the system. Plant trials are also discussed with reference to the commercial aspects of a full-scale implementation of sonic injection in the smelter."

Jan 1, 2015

By R. Abela

Heavy mineral sands are usually beneficiated in a spiral concentrator circuit prior to separation of heavy minerals into streams of zircon, rutile and ilmenite. The performance of the spiral concentrators is heavily affected by the presence of slimes in the rougher feed. The paper quantifies the effect of slimes content and discusses the beneficial effect of spiral feed de-sliming. The net effect of inefficient slimes removal can cause significant recovery losses of the heavy minerals present in the feed.

Jan 1, 2003

By F. T. Cawood, M. A. Jooste

This paper describes the survey monitoring processes at Venetia, which are discussed under visual inspections, ad hoc investigations, system monitoring and slope stability radar monitoring. This is followed by a description of the main survey monitoring methods. The next section briefly states typical problems, i.e. the atmospheric corrections required to adjust total station distances, maintenance of the system and management of the monitoring process. The paper ends with some important lessons that could be applied to similar monitoring programmes. These lessons are firstly, communication is most important, process a vital part of the system, a champion must take responsibility for the programme and system planning ensures that the monitoring results are needs driven.

Jan 1, 2006

Virtual Reality (VR) simulations are excellent tools for training, education, simulation of abnormal and dangerous conditions in mines and solving complex problems. Although the concept of VR has been around for nearly half a century, it has taken recent advances in hardware and software to bring this technology to within the budgetary reach of ordinary users and researchers. VR is now successfully being used in the minerals industry for: data visualization, accident reconstructions, simulation applications, risk analysis, hazard awareness and training. The Institute of Sustainable Minerals Industry, Advanced Computer Graphics and Virtual Reality Research Group (SMI-VR) at the University of Queensland, established in late 2000, has been involved in developing VR applications for the minerals industry in conjunction with various research centres. This paper illustrates the benefits of using advanced computer graphics and VR techniques in the minerals industry with some examples of applications developed.

Jan 1, 2003

By D. L. H. Bulbring

The removal of a cylindrical core from thick-wall sections for creep analysis by the relatively new Weldcore® process represents a very exciting methodology for obtaining more representative creep damage data from large engineering structures. The cylindrical core that is removed, representing about 60% of the wall thickness, leaves a substantial removal site that needs to be repaired. This paper presents data pertaining to taper Friction Hydro Pillar Processing as an alternative repair technique for filling the core removal site. Process parameters were evaluated with special attention being paid to the effect of downward force on process response variables, weld defects, and mechanical properties of 10CrMo910 steel. Process temperature and torque response as well as total process energy input were also considered. This paper also assesses the static and dynamic performance of this repair technique. The influence of a varying downward force and the occurrence and position of discontinuities were quantified. Downward force was shown to have the most notable effect on weld joint dynamic performance and was found to be related to the process temperatures achieved in close proximity to the weld interface.

Jan 1, 2013

By T. Wettainen

Malmberget town is located in northern Sweden, approximately 70 km north of the Arctic Circle. Parts of the town overlie more than 20 iron orebodies, consisting mainly of magnetite with smaller quantities of haematite. The mine is operated by the mining company LKAB. Mining started in the 17th century, but not until the railway to the coastal city of Luleå was completed in 1888 did large-scale production commence. Around 1920, mining proceeded underground and today sublevel caving is the only mining method used. Sublevel caving causes subsidence of the ground surface, and buildings and residential areas have been relocated due to the mining activities for more than 50 years. The number of seismic events accompanied by strong ground vibrations is now increasing. In 2008 the mine received a permit from the Environmental Court of Sweden to increase production to 20 Mt of crude ore per year. A prerequisite for the permit was that the mine conducts a number of investigations regarding the environmental impact on the residents of Malmberget. One of these investigations concerned how seismicity will change as production increases and what measures could be taken to reduce inconvenience to the town residents. Today the mine possesses an extensive seismic monitoring system with more than 180 underground and surface geophones. For this study, eleven seismically active volumes in Malmberget mine were identified, and for each of them, a yearly future maximum magnitude interval was estimated based on the current production plan. Relationships between historical seismic events and measured ground vibrations in the town of Malmberget were established, and future ground vibrations caused by expected seismic events were estimated using a probabilistic approach. The outcome was the number of intervals of expected ground vibration per year and per monitoring point. Possible measures to reduce inconvenience for the town residents include blast restrictions, sequencing, and possibly preconditioning. The ultimate long-term solution is an almost complete relocation of Malmberget town. This process has recently been formalized and LKAB is taking an active part in realizing this goal.

Jan 1, 2014

By G. M. Cresswell

The 2 360 t/h two module Phola coal preparation plant represents anew era of large plant in the Witbank coalfield designed to extend its life to 2020 and beyond. The plant uses the optimum processing model for Witbank coals, receiving a feed coal size of -50 mm, wet screening it into coarse and small coal fractions 50 x12 and 12 x0.63 mm before processing them in parallel through two primary DM cyclone sections, in order to make a 27.5 MJ/kg export floats product. The sinks are processed through a common high density DM cyclone section to produce a 21.5?23 MJ/kg thermal coal middlings product. The plant design incorporates the largest size DMS equipment used to date in South African coal preparation plants, i.e. 1 150 mm large diameter pump fed DM cyclones and 4.2 m width banana screens. The fine coal is conventionally processed by spirals, whereas the raw coal slimes are filtered using automated plate and frame filter presses and added to either the middlings or discards depending on its quality. The paper describes the database, innovative design concepts, construction, and commissioning.

Jan 1, 2010

By A. H. Mokken

Failed attempts at amalgamation of a gold/osmiridium concentrate, recovered behind pebble mill liners during re-lining, led to the discovery that the gold particles were coated and that nitric acid only could remove the coatings. Following this treatment amalgamation was rapid and resulted in a complete recovery of the gold that otherwise would have been lost in plant residues. Investigations into the nature and formation of the coatings led to the realization that the coatings were impregnations of harder elements, associated with the gold during grinding and driven into the softer gold surface by high pressure, impact and attrition. It was further realized that this phenomenon could be part of gold ore milling, world-wide. With these thoughts in mind the question is asked whether concentration down to micron sizes prior to cyanidation, should not play a greater role in gold recovery.

Jan 1, 1999

By I. L. Follington

This paper describes the research and development programme to develop a prototype underground auger mining system aimed at developing and demonstrating an underground auger mining system able to provide economic access to thinner (<1.8 m) coal reserves of South Africa. Data concerning the performance of modern coal augers under South African coal mining conditions were gained from a proven surface auger which operated across a range of coal types. These data were analysed and considered in conjunction with historical information regarding previous attempts at building underground augers dating back to the 1950s. Drawing on these data a prototype underground auger mining system, the BryDet BUA 600 underground coal recovery auger, was designed and manufactured by the BryDet Development Corporation in collaboration with Eskom and Cutting Edge Technology Pty Ltd with support from Anglo Coal and the Ingwe Coal Corporation Ltd. The prototype BryDet BUA 600 underground coal recovery auger commenced trials in March 2000 at the Matla Mine near Witbank in South Africa. The initial trials were undertaken in an open cut to facilitate the commissioning and training associated with a prototype mining machine. A total of 30 holes was augered in the box cut before the machine moved underground. The prototype BUA 600 first achieved the target penetration depth of 80 m in its third hole. The prototype BUA 600 is a new underground mining system which has passed early testing with ?flying colours? and could provide access to extensive underground coal reserves unmineable by conventional mining techniques both in South Africa and elsewhere around the world.

Jan 1, 2001

By M. A. van Nierop

Load behaviour in an industrial mill has been measured directly by inserting probes through liner bolts. The data from conductivity probes have indicated the presence of premature centrifuging during manipulation of the load mass. Overloading conditions were also encountered. Overloading and premature centrifuging both reduce the power drawn by the mill. These effects have been successfully modelled.

Jan 1, 1997

By G. van Hout, D. Rahal

Caving is a mass mining method that is normally applied to large, low grade orebodies because of its low production cost and high capacity. However, equipment breakdown and poor draw management can cause mining costs to exceed that of all other mining methods. One way to minimize the effect of disruptions in the mining cycle is to use Mixed Integer Linear Programming (MILP) for long-term scheduling. This paper describes a MILP goal program which has the dual objectives of minimizing deviation from the ideal draw profile while achieving a production target. Schedule optimization is performed using a life of mine approach in which all production periods are optimized simultaneously. The underlying assumption being that material mixing in the short-term (between monthly optimization cycles) has a minimal effect on the long-term state of the panel. Schedule optimization is carried out using six general constraint types to model and control production. The constraint types define: deviation from ideal practice, panel state, material flow conservation, production quality, material flow capacity and production control. These constraints define production targets and drive production toward the ideal profile while maintaining correct mining practice. Application of the model using production scheduling data for a De Beers kimberlite mine. It is shown how different production control constraints regulate production from individual drawpoints as well as recovery of the ideal panel profile by implementing an optimised draw schedule.

Jan 1, 2003

The influence of varying amounts of magnesia, silica, and alumina in iron ore sinter on its mineralogy, reducibility index (RI), reduction disintegration index (RDI), physical breakdown (AI and TI), and production properties (coke breeze rate) were examined. It was found that the mineralogy of iron sinter can more easily be predicted from its chemical composition than from the RI, RDI, AI or TI. Anticipating the consequence that varying amounts of MgO and SiO2would have on sinter properties is complex, and not necessarily predictable. High concentrations of Al2O3in the sinter result in high concentrations of the SFCA phase, but with drastically deteriorated properties. This study also confirmed that the form in which fluxes are added to the raw material sinter mixture affects the mineralogy and properties of the produced sinter.

Jan 1, 2010

By A. V. Roschin, V. E. Roschin

Composite ores are more often used for production of iron in connection with reserve depletion of traditional ore crude in the regions with developed metallurgy. In particular, the majority of perspective ferrum-ore deposits of the Urals are presented by titanferous magnetite ores which contain a significant amount of titanium and vanadium alongside with ferrum. Thus, the deposits of titanferous magnetites of the Southern Urals on the average contain about 20 % of Fe, 8,7 % TiO2 and 0,24 % V2O5. Due to a high content of titanium oxides it is impossible or it is inexpedient to process such ores in blast furnaces. During work just on titanferous magnetite ore refractory titanium-containing slags are formed in a blast furnace, and in case of its dilution by ores of different types the titanium due to the small content in slag is thrown out. It is often impossible to separate such ores into ferriferous and titanferous concentrates because ferrum and titanium are present in the same minerals. This work attempts to selectively reduce ferrum in solid oxide and to separate metallic iron from titanferousslag with fast fusion. Solid-phase reduction of ferrum has been carried out with carbon at temperature of 1000? 1300°?. In products of solid-phase reduction the extremely disperse mix of metal iron and only partially reduced titanium oxides have been achieved. It is impossible to separate such a mix mechanically. However, the fast fusion of the mix allowed separating it into cast iron and slag with the high content of titanium. Thus the cast iron contained less than 0,1 % of titanium, and the slag did not contain practically any ferrum.

Jan 1, 2007

By M. Bwalya, L. Mabokela, L. C. Woollacott

This paper presents a study on the ability of the King stratification modelto describe density stratification patterns that are achieved under idealizedconditions. Tests were conducted in a batch jig using artificial particles inseven density classes. All particles in a density class had essentially thesame density, size, and shape. Tests were conducted for particle systemsinvolving from two to seven components. Good agreement was obtainedbetween measured and modelled data to an extent that gave strongendorsement of the mathematical appropriateness of the core equation inthe King model. Somewhat ambiguous results were found with regard toclaims about the independencies of the single experimentally-determinedparameter required by the model.

Jan 1, 2015

By R. Heuberger

South Africa?s Mining Industry operates in an uncertain world. The industry is buffeted by problems regarding retrenchments, unemployment, low productivity, rising costs, volatile exchange rates, commodity prices and government regulations. With these uncertainties facing the decision makers, what does applied technology offer the industry?s management? Modelling languages with risk analysis have been available for decades, but in the past their use has been very expensive, requiring large mainframe computers and lots of computer time. Today, PCs and laptops have incredible power, which makes interactive risk analysis affordable and viable for all enterprises, whether small or large. ?What is risk analysis? ?What is Monte Carlo simulation? ?What kinds of computer models need to be created to use risk analysis and Monte Carlo simulation effectively? This paper addresses these questions and illustrates, with a practical example in the mining industry, how risk analysis techniques can be used to support decisions in the climate of uncertainty.

Jan 1, 2005

Assuming that a gold ore has been effectively ground to ensure maximum economic liberation of gold, the circuits that will have the most effect on the successful operation of a gold plant will be that of the leaching and carbon-in-pulp circuit (CIP). The reagent and utilities operating costs associated with leaching, adsorption, elution and regeneration would typically make up some 15% of total operating cost, whilst the capital costs associated with these areas is about 16% of the total. Although not largest (capital and operating costs associated with comminution are generally dominant) these items represent a significant proportion of capital and operating cost. Much more importantly, these plant areas represent the primary gold recovery process and their technical and operational efficiencies will have a significant impact on overall plant efficiency. The objective during process design of these sections is thus to develop a design which provides maximum technical and economic efficiency and which is robust to potential changes in ore throughput, mineralogical characteristics and head-grade. Experience has shown that, particularly for longer life and higher-grade projects typical of the South African underground gold mining industry, small changes in recovery and efficiency have a significant value over the life of the project.

Jan 1, 1999