Search Documents

By R. V. Ramani, A. S. C. Owili-eger

The origin of gaseous hydrocarbons in coal, predominantly methane, can be traced to the natural processes of coalification. The higher rank coals or the more deeply buried seams retain more gas than low rank coals or shallow seams. It is estimated that up to 460,000 cubic feet of all types of gases are produced during the formation of one ton of coal (Cervik, 1969). The chief components of these gaseous products are methane, carbon dioxide, nitrogen and water vapor. Most of these gases escape during the various stages of decomposition but with eventual presence of overlying impermeable beds, there may be as much as 2,000 cubic feet of gas retained per ton of coal. Over geologic time, diffusion and other processes such as geologic disturbances in the earth's crust remove all but 500 to 2000 cubic feet of gas per ton of coal (Cervik, 1969). It is this residual methane which is of primary concern when mine openings are made in coal measures. Extensive data compiled by the United States Bureau of Mines reveal that some coal mines in this country emit up to 20 million cubic feet of methane per day (Spencer, 1970; Irani et al, 1972). Toxic, poisonous and respirable gaseous pollutants and explosive gases, predominantly methane, are injected into the ventilation stream from active sections and gobs. The liberation of methane in gob areas may, under certain circumstances, become extremely large. In some instances it may constitute up to 70 percent of the total yield of gas in a mine. The basic physical factor which determines the yield of gas into the mine environment is the gas content of the seam. The influence of the gas content of a seam on the overall yield of gas

Jan 1, 1974

By J. F. Barkley

"In trying various coals at one of the Government power plants, comparison was made of the ash softening temperature of each coal, with the clinkering tendencies of the coal when burned in the furnace. The proximate analyses, ash softening temperature and plant reports as to clinkering were tabulated. It was desired to bring out any correlation that might appear between the ash softening temperature found in the laboratory, and the clinkering of the ash as found in the boiler furnace.Each coal used was sampled and analyzed, and the standard ash fusion test made. The clinkerring of the coal in the furnace was observed by the furnace operator. The furnace equipment consisted of the ""V"" or Murphy type of stoker with the ordinary fire-brick arch roof. With such arrangement very high furnace temperatures are apt to be produced at the ratings carried at this plant.The softening temperature of ash is defined as the temperature at which small cone of the ash, as tested in the laboratory furnace, has fused down to a spherical lump, The softening interval is the difference between the softening temperature and the temperature at which the first rounding, or bending, of the apex of the cone takes piece. The flowing interval is the difference between the softening temperature and the temperature at which the ash has reached a fluid condition as shown by spreading out over the base in a flat layer.While the analyses of the different samples of the some coal did not vary appreciably, the ash softening temperatures were not always so consistent. It will be noted from the following examples that the ash softening temperatures of different samples of the same coal differ as much as 290° F, Hence, in order to judge this property of a coal, many samples ore desirable, taken from many different shipment."

Aug 1, 1924

By C. W. Davis

"A copper-palladium-gold-silver ore is being mined at Salt Chuck, Prince of Wales Island, Alaska, from which a concentrate is produced that contains 40 to 50 per cent copper, and considerable amounts of palladium, gold and silver. There has been much difficulty in obtaining assays for palladium, gold and silver from the mine, smelter, sampler, and umpire that check within reasonable limits. While the results for copper content have not been unusual, the results for palladium have varied as much as 0c8 oz. on 3 oz. material, results for gold differed by 0.1 oz. on 1.6 oz. materials, and for a silver content of 7 oz., results differed by as much as 4.0 oz.The Bureau of Mines was requested to determine the causes of variation in the results of the different assayers, and to develop a satisfactory procedure for analyzing such ore.Three samples of concentrate were received for analysis, two small lots that had previously been assayed by the various laboratories, and one large sample. The large sample was dried and ground in a ball mill, put through a 150-mesh screen, and then returned to the ball mill for thorough mixing. The small samples were ground to pass a 150-mesh screen and then mixed on a mixing wheel.The large sample (No. 1) was analyzed by five different procedures, one of the small samples (No.2) by three procedures, and the other (No. 3) by two procedures (the two small samples being too small for further tests). The different procedures tried and the results obtained arc presented below. The samples of concentrate were from ore mimed and milled by the Alaska palladium Co. at Salt Chuck."

Feb 1, 1926

By Ivette E. Torres

Table 8 provides data for the estimated value of world export trade of all mineral commodities from 1980 through 1991. It also provides a breakdown of the total into mineral fuels and non fuel minerals. These data have been developed from UN export trade data presented in table 9. The percent distribution and growth of the value of world export by major commodity groups are presented in tables 9, 10, and 11, respectively. In terms of industrial minerals (nonmetals), data in tables 10 and 11 include crude industrial minerals only, while table 8 includes an estimate for other industrial minerals. The 1991 estimates that appeared in the 1991 issues of this publication have been revised. It is typical for this section to review the year prior to the year of review because of the unavailability of data at the time of publication. The aggregated value of export trade in mineral commodities for 1992 was not available at the time of publication. The total value of nonfuel and fuel mineral exports for 1991 was about $616 billion in current (1991) dollars. The value of mineral fuel export trade accounted for about 53 % of the total mineral export trade. In 1980, the contribution of mineral fuel to the value of mineral commodity export trade had been almost 68%. The 1991 world mineral commodity export trade represents a 5.3% decrease (table 8) from that of 1990. The largest decrease was attributed to the decrease of export trade of fuel minerals (5%). The value of non fuel mineral export trade decreased by 4 %. Because the value export trade of all commodities increased by 1.2 %, the share of mineral commodities decreased from 19.2 % to 17.9 % of the total.

Jan 1, 1994

Minimize drilling time in roof bolting. Approach The Bureau of Mines conducted a survey of 34 roof bolting machines used in underground coal mines. Results of the survey indicated that drilling time, bit cost, and respirable dust concentrations and be reduced by using the appropriate bits for drilling, To evaluate bits currently used and to find optimum cutting parameters needed to minimize drilling time, the Bureau tested two bits commonly used in most underground mines on both wet and dry systems. These are the dusthog* and shank type. The dusthog has dust ports in the bit body to remove cuttings. With shank bits, holes in the drill steel do this. Cost of each type is roughly equal. Bolters with dry vacuum systems were tested in the laboratory first. The lab tests were verified by underground tests in several mines. Bolters with low-pressure wet drilling systems were also tested under-ground. Tests concentrated on the effect of rpm, water and airflow rates, heating, wear, bit design and bit type. Lab Results -Dry Drilling Holes were drilled during the laboratory tests using a production model bolter drilling 45-inch-deep holes into mixtures of lime stone and sandstone aggregate. All tests started with new shank and dusthog type bits at 225 and 450 rpm. Thrust was about 6,000 lbs in all tests. Each bit was tested at two airflows, 15 and 25 cfm, airflows which are typical on operating roof bolter bits. Eleven styles of bits were evaluated. On the average, dusthog bits drilled 25% faster than shank types and were always cooler after drilling. The effect of RPM was tested with 5 different bit types. When bit rpm was increased from 300 to 400, drilling rates doubled. With used, well-worn bits drilling time and final bit temperature were more than doubled.

Jan 1, 1986

By H. E. Sanford

"INTRODUCTION Of the occupations in and about coal mines, those of the haulage crews are among the most hazardous. Statistics indicate that the second largest number of fatalities about coal mines occurs during haulage operations and through the use or misuse of haulage equipment. Despite the fact that relatively few coal-mine employees are engaged continuously at haulage operations, approximately 20 percent of all coal-mine fatalities are attributable to haulage.Most of the hazards in haulage operations could be very greatly reduced if more serious consideration were given to the problems of the haulage crews and if sincere efforts were made to reduce the hazards. Underground haulage is similar in many respects to railroading; yet, railroading is now considered one of the safest of occupations a distinction that has been attained only by honest effort and whole-hearted cooperation on the part of all concerned. Underground haulage is also similar to street and highway operation and has in it some of the difficulties encountered in the reduction of traffic accidents the seriousness of which has not by any means been con¬trolled as yet, notwithstanding the fact that much effort has been expended through a multiplicity of laws, ordinance regulation, etc., as well as by thousands of enforcement agencies and officers.The men working on the locomotives are among the most important members of a coal-mine organization; without skilled haulage employees, the production of coal would be greatly retarded. Their jobs, particularly the job as brakeman, require physical endurance, agility, and mental and physical alertness; in thin coal beds, especially where the roof is not brushed and the coal is loaded into mine cars by hand, the need for these qualifications is greatly increased."

May 1, 1948

By R. P. Beyer

[The Bureau of Mines has measured the low-temperature heat capacities and high-temperature enthalpies of crystalline K2Si2O5 as part of a program for advancing mineral resources technology with energy economy. High-temperature enthalpies of glassy and liquid K2Si2O5 and crystalline K2SiO3 were also mea¬sured. An adiabatic calorimeter operating over the range 5 to 308 K was used for the heat capacity measurements for K2Si2O5 from which the standard entropy at 298.15 K, S°298 = 45.55 ±0.05 cal/deg-mole, was calculated. Tabulated values of Cp°, S°, -(G° -HO°)/T, and H°-HO° from 5 to 300 K are given for K2Si2O5. A copper-block drop calorimeter was used in the enthalpy measurements, operating from 298.15 to 1,198 K for K2SiO3 and from 298.15 to 1,453.8 K for K2Si2O5. No transitions were found for K2SiO3. The KI2Si2O5 showed two reversible first order transitions, one at 510 K with a heat of transition of 0.29 kcal/mole and one at 867 K with a heat of transition of 0.38 kcal/mole. The heat of fusion for K2Si2O5 20 5 was calculated to be 8.42 kcal/mole. Relative enthalpies are given in equation form, and high-temperature values are tabulated for Cp°, S°, - (G°-H°298 )/T, and H°-H°298 . Also tabulated are ?H°, ?G°, and log K for formation of K2SiO3 and K2Si2O5 from both the elements and the oxides.]

Jan 1, 1979

This surveillance report summarizes data on work-related fatal and nonfatal injuries, illnesses, and hazardous exposures in the mining industry for the 10-year period 1986-1995. The term "surveillance," as used in public health, may be new to many readers of this report. With regard to occupational safety and health, the goal of surveillance is to describe the occurrence of work-related injuries, illnesses, and known hazardous exposures; to identify new hazards that may occur due to the introduction of new technology or other factors; and to assess the effects of preventive measures designed to improve worker safety and health. Surveillance provides an overall picture, which can be used to focus resources on areas most in need of prevention programs or further research. Surveillance generally requires the use of multiple sources of data, all of which have their own strengths and limitations. Surveillance in the U. S. mining industry is complicated by the fact that U.S. national data systems that provide information on mining are based on two different definitions of the mining industry. One is established by the Mine Safety and Health Administration (MSHA), the other by the Standard Industrial Classification (SIC) System [Office of Management and Budget 1987] and the 1980 U. S. Bureau of the Census (BOC) Classification System [U.S. Bureau of the Census 1982]. The mining industry as defined by MSHA is based on the regulatory jurisdiction of that agency. Reporting requirements for injuries, illnesses, and workplace exposures are stipulated under the Federal Coal Mine Health and Safety Act of 1969 and the Federal Mine Safety and Health Amendments Act of 1977. Of note is that the oil and gas extraction industry falls outside of MSHA jurisdiction. The Occupational Safety and Health Administration (OSHA) was charged with enforcement in the oil and gas industry under the Occupational Safety and Health Act of 1970. Under the SIC, the definition of mining covers the extraction of naturally occurring minerals, including liquids (petroleum), gases (natural gas) and solids (coal, metal, and nonmetallic minerals). Exploration and development of mineral properties are also included in the SIC definition of the mining industry. The SIC was developed by the Office of Management and Budget for use in classifying establishments based on the type of economic activity in which they are engaged and serves as the industry classification standard for all establishment based Federal economic statistics. This classification is important for occupational safety and health surveillance because it also serves as the industry classification system for all data on work-related injuries and illnesses collected by the U.S. Bureau of Labor Statistics (BLS). The U.S. Bureau of the Census uses an industry coding scheme similar to that used by the SIC. For the mining industry, the categorization is identical in both systems. Death certificate data made available by the National Center for Health Statistics (NCHS) are categorized under this system. Death certificate data are particularly important for surveillance of mortality from work-related illnesses. Key differences between the SIC/BOC categorization system and the MSHA system can be summarized as follows: • MSHA excludes the oil and gas industry, which is classified as part of the mining industry under SIC/BOC. • MSHA excludes work that is done off of mine property; work off of mine property is included under SIC/BOC if it is performed by an establishment falling into one of the SIC/BOC mining industry codes. • MSHA includes mine-associated mills and processing plants; these are classified under the manufacturing industry, rather than mining, according to the SIC/BOC coding structure. Since the data collected by MSHA and the data collected by BLS and NCHS using the SIC/BOC classification system are both important sources of information on the mining industry and in many cases serve different purposes, data from both systems are presented in this report. In general, data using the SIC/BOC system are comparable across U.S. industries and should be used when comparing mining to other U.S. industries. Much of the data in this report are presented in the form of frequencies or rates. A frequency provides only a count of the number of cases without providing any information about the risk of occurrence. Rates provide an estimate of the risk of injury or illness. The reader is cautioned, however, that rates based on small numbers can be unstable; thus, any inferences should be drawn with care. In this report, no rates are presented for groups in which there were fewer than three cases. The incidence of most injury and illness conditions differs by age, sex, and race. For this reason, data in many surveillance reports are adjusted for these demographic factors. It was not possible to do this for most of the rates in this report because information on demographics was not available. With the exception of the proportionate mortality ratios (PMRs), all data presented are unadjusted. A detailed account of the sources of data is in appendix A. The methods used in data selection and analysis are described in appendix B.

Jan 5, 2000

By Samuel A. Goldberg

The Federal Coal Mine Health and Safety Act of 1969 delegated to the Bureau of Mines a yearly program of health inspections. Respirable coal mine dust concentrations are measured by Bureau inspectors. Samples of respirable coal mine dust are weighed to determine dust concentration and then analyzed for ash and quartz content. This paper describes the laboratory procedure for determining the percent quartz in the respirable coal mine dust samples.

Jan 1, 1972

By Chas F. Jackson

 The annual reports of the supervising engineers of the several sections of the Mining Division are assembled herein and comprise the annual report of the division. During the year under review the work was oriented entirely to the war program by applying apparatus and technique previously developed in research directly to war problems, as well as by intensified search for and exploration of deposits of minerals necessary in the war.

Oct 1, 1942

By H. W. Lang

The Bureau of Mines conducted an investigation to observe the effect of cetane improvers upon nitrogen oxides concentration in diesel exhaust gas. Amyl nitrite and amyl nitrate were used as additives to the fuel used in a four-cycle, single cylinder type test engine. It was concluded that nitrogen oxide concentrations were not enhanced at fuel-air ratios above 0.03 pound of fuel per pound of air.

Jan 1, 1969

By J. A. Organiscak

The U.S. Bureau of Mines recently conducted an investigation into the amount of respirable and quartz dust generated while mining rock in coal mines by continuous and conventional methods. The study was made at two mines that use both continuous and conventional mining. Results show that continuous mining produces 1.2 to 3 times more respirable dust, and 6.7 to nearly 15 times more quartz dust than conventional mining.

Jan 1, 1989

By D. A. Paice, A. B. Shimp

Illegitimate loads on a mine dc power distribution system can be detected by measuring a superimposed ac current. To implement such a scheme, a 10-volt, 3-kHz voltage is applied at each dc power substation. By this means, the mine dc power distribution network, consisting of a feeder and trolley wires with a grounded rail return, is caused to serve also as a 3-kHz ac distribution network.

Jan 1, 1975

The following methods should be used to protect miners from the adverse health effects of exposure to respirable coal mine dust and respirable crystalline silica: ? Informing workers about hazards ? Establishing written emergency procedures ? Using engineering controls, work practices, and personal protective equipment (including respiratory protection when dust control equipment is being installed, maintained, or repaired) ? Monitoring exposures ? Conducting medical screening and surveillance ? Encouraging smoking cessation ? Maintaining medical records

Jan 1, 1997

By E. Morrice

The effect of the temperature of SmF3-LiF electrolyte on the electrolytic preparation of samarium-cobalt alloy by the consumable cathode technique was investigated. The temperatures of the cathode zone, alloy collection zone, and samarium oxide (Sm203) feed zone had to be controlled carefully to obtain a satisfactory samarium-cobalt alloy product. Any appreciable deviation from certain temperature values adversely affected yield and product quality.

Jan 1, 1971

By D. E. Wolfson

Destructive distillation (carbonization) was shown to be a feasible method of disposing of scrap tires. The Bureau of Mines conducted tests under a variety of conditions. Solid, liquid, and gaseous products were produced, recovered, and analyzed. The quantities of the various products were shown to be quite dependent on the test temperature. Variability in composition of the liquid and gaseous products with changes in test temperature was also significant.

Jan 1, 1969

By S. J. Pearce

The Bureau of Mines has prepared, as circumstances have dictated, a series of schedules setting forth the minimum requirements that various types of equipment should meet to be considered safe and satisfactory for use under certain hazardous or unhealthful conditions. These schedules cover a wide variety of devices ranging from explosives to electrically operated mine locomotives. This paper discusses the functions and operations of schedules under which respiratory protective devices are tested and approved. It emphasizes that the aim of the Bureau respirator-approval system is to make available to the public respirators that meet definite performance requirements. The responsibility of the respirator manufacturer in pre-testing the device and in maintaining its quality after it is approved are explained. Aid is provided for the user in selecting the proper device for specific application, and a plea is made for better education of all concerned in the proper use of the devices. DISCUSSION Provisions have been made for testing and approving the following types of respiratory protective devices: Self-contained breathing apparatus,2/ supplied-air respirators,3/ gas masks,4/ dispersoid respirators,5/ and chemical-cartridge respirators.6/ These devices are tested at the Central Experiment Station of the Bureau of Mines in Pittsburgh, Pa. Self-contained breathing apparatus is tested by personnel of Health and Safety District B; other types of respirators are tested by the Branch of Health Research.

Jan 1, 1957

By A. B. Hooker, E. J. Coggeshall

"INTRODUCTION Ignitions of gas at the coal face when a blast is fired electrically are often a tributed to the explosive; but sometimes the ignition cannot be explained satisfactorily in this way-in fact, ignitions have occurred when the detonator has failed explode.The possibility of such electrically by sparks from the blast between poorly insulated leading wires and detonator leg have been recognized. Several countries have provided safe types of single-shot blasting units; some have permitted the use of larger multiple-shot blasting units provided each unit is equipped with a time-limiting switch that prevents unnecessarily long application of voltage on the leading wires after the shot has occurred, the assumption being that the firing line will this be dead before damage to the wires and subsequent sparking can take place. An extensive research was made by a French commission relative to the characteristics of electric detonators and methods of firing. Along other tailings they investigated the probability of ignitions by sparks across the leading wired at the face, also the time and duration of the various events in blasting, such as ignition of the detonators, movement of the coal face, and application of firing current. They suggested, as a means of eliminating or reducing tilt possibility of gas ignitions from the blasting unit, that the timing switch of the blasting unit be designed to disconnect the blasting"

Oct 1, 1934

By EINAR M. ARENTZEN

This information circular. deais primarily with an engineering descrip- tion of a type of longwall cutting and loading machine developed by Eick- hoff Maschinenfabrik, Bochum, Germany..: This machine is supposed to have been developed and tested during the latter part of 1941 and early 1942. The only source of information is con- tained in certain literature and engineering data, with drawings which were acquired by the Allied Military Authorities when Germany was occupied; and the information will have to be limited because the writer has not seen the machine in the factory or in operation. However, the information may be of interest to the coal-mining industry in this country, and for this reason our Government has decided to publish the data procured so far. The Eickhoff cutting and loading machine is particularly suitable for the longwall mining system. It can only be used under that type of mining system and is not suitable for the more common type known in this country as room-and-pillar work. The material for the description of the machine and its operation was compiled and translated from German drawings and operating instructions. These detailed drawings and instructions are on file with the Bureau of Mines and are available for inspection by any responsible person interested in the details of the construction of the machine.

Dec 1, 1946

By Earl C. Lane

The Bureau of Mines is making a survey of petroleum products manufactured on the Pacific Coast from California crude oils . California crude petroleum is known to differ in some characteristics from the crude oil produced in other parts of the United States , and the claim has been made that the present Federal specifications are unduly severe when applied to the products made from California crudes . The main purpose of the present survey is to determine whether these claims are justified . This report deals only with California gasolines . Other products , such as burning oil , fuel and lubricating oils , will be taken up later . The samples reported were furnished in most cases , by the four large refining companies located on the Pacific Coast , although a number of samples of motor gasoline were purchased in the open market . In Los Angeles , samples of motor gasoline were obtained from service stations representing as many different refineries as possible . Inasmuch as San Francisco is one of the cities covered by the regular semi -annual motor gasoline survey conducted by the Bureau of Mines , it was not considered essential that the set of samples obtained from this city be as comprehensive as would otherwise have been necessary . The gasoline consumed in the States of Washington and Oregon is furnished for the most part by California refineries , and no effort was made to procure samples from these States .

Apr 1, 1922