Search Documents

Provide a portable crushing capability to keep conveyor haulage close to the working face and permit more efficient and safer ore handling in low headroom, hardrock mines. Approach A readily portable jaw crusher is used which meets machine size, feed rock size, product size, and throughput requirements for low headroom, hardrock mines. How It Works The crusher is mounted on wheels to expedite frequent moves and to allow crushing of mined rock or ore near the working face. The crushed product is then placed on conveyor belts that are ex-tended as the crusher is moved. Keeping crushing and conveyor haulage near the face minimizes the haulage distances for trucks and loaders. Loading and haulage of run-of-mine ore is frequently the highest operational cost in underground mines. These costs can be significantly reduced by use of a belt conveyor, which is a common practice in coal and other soft mineral mines. The new low-profile hard rock crusher gives the same advantage of extensive belt haulage capabilities to low headroom, hardrock mines. The low-profile crusher will accept feed up to 30 inches when operating under 11 feet of headroom. The headroom required for crusher operation was reduced by tilting the jaws, feeding the crusher horizontally, and placing the eccentric shaft at the back or in a horizontal plane with the jaws. Material is fed by an

Jan 1, 1981

By Richard J. Mainiero, Michael J. Sapko, Marcia L. Harris

Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings and one fatality. To better understand the factors contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out studies in a 12-foot diameter sphere to identify key factors that may enhance the levels of CO associated with the detonation of several commercial trenching explosives. The gaseous detonation products from emulsions, a watergel, and ANFO blasting agents as well as gelatin dynamite, TNT, and Pentolite boosters were measured in an argon atmosphere and compared with those for the same explosives detonated in air. Test variables included explosive formulation, wrapper, aluminum addition, oxygen balance, and density. Major contributing factors to CO production, under these laboratory test conditions, are presented. The main finding is the high CO production associated with the lack of afterburning in an oxygen poor atmosphere. Fumes measurements are compared with the manufacturer’s reported IME fume class and with the Federal Relative Toxicity Standard 30 CFR Part 15 in order to gain an understanding of the relative toxicity of some explosives used in trench blasting.

By David C. Oyler, Paul W. Jeran, William P. Diamond

The Bureau of Mines is cooperating with the U.S. Department of Energy in a directional degasification project at the Emerald mine near Waynesburg, Pa. This project is designed to combine the highly successful underground horizontal degasification technology with surface drilling methods. The objective of this program is to demonstrate that directional drilling can be used as a technique for degasifying coalbeds ahead of mining to reduce the hazards of methane-air explosions in coal mines. The directional hole at the Emerald mine is designed to start vertically and enter the Pittsburgh coalbed horizontally. A 3-inch-pilot hole entered the Pittsburgh coalbecl at a vertical depth of 999 feet, The hole will be reamed to 8-3/4 inches in diameter, and 5-1/2-inch casing will be cemented in place. Three individual 3-inch-diameter, 3,000-foot horizontal gas collection holes will be drilled into the coalbed in a “bird foot” pattern. A corehole and vertical dewatering hole have been completed at the anticipated coalbed intercept. The dewatering hole was drilled to130 feet below the Pittsburgh coalbed, a depth of 900 feet, and 880 feet of 7-inch-OD casing was cemented in place. Seven vertical holes for monitoring the extent and progress of degasification have been drilled within the horizontal drilling area.

Jan 1, 1979

By R. A. Guidotti

The Federal Bureau of Mines has studied the reaction of oxides of columbium, vanadium, and tantalum with ammonia in vertical, gas-solids reactors at temperatures ranging from 300° to 1,300° C with the goal of preparing nitride intermediates for subsequent preparation of the metals by a thermal-decomposition step. The best nitride conversions were obtained in nonmetal reactors. With Cb205, V2O3, and V205 , low-temperature maxima in reaction rates occurred at 800°,800°, and 450° C, respectively, during oxynitride formation (in A1203) at 1 atm of pure ammonia. Conversion of the oxynitride, in a second step, to the mononitride was optimum at 1,200° C for columbium and 1,050° C for vanadium. In the case of Ta205, the rate of reaction to form Ta3N5 (in a single step) was highest at 900° C, where the presence of up to 5 percent methane was found to be beneficial; improved results were obtained by conducting the nitriding in a rotary kiln. Optimum space velocities (in the vertical Al203 reactor) ranged from 5,280 hr-1 for Cba205 to 7,950 hr-1 for V203. Oxide particle size had little effect upon reaction rates. Under fully optimized conditions, products containing less than 1 percent oxygen were readily obtained in under 6 hours.

Jan 1, 1975

By H. R. Babitzke

The purpose of this investigation was to evaluate the potential of columbium-hafnium alloys as structural materials for use at elevated temperatures. The work described in this report was conducted to determine the properties of columbium-hafnium alloys and to select the more promising ones for further improvement. Properties determined in this report were machinability, hardness, workability, tensile strength, and oxidation resistance. Ten ingots, ranging from 100 percent columbium to 70 atomic-percent hafnium, were prepared and subjected to tests. The test results showed that the alloys with 33 and 50 atomic-percent hafnium were superior in workability, strength, and oxidation resistance. For the alloy series tested, the strength and hardness values increased with the increasing hafnium content. Maximum values were reached with 50 atomic-percent hafnium. The oxidation resistance was poorest at the 1 atomic-percent hafnium level but improved with increasing hafnium content through 70 atomic-percent. Eight of the ten ingots were fabricable at room temperature. The two remaining ingots, those with 5 and 10 atomic-percent hafnium, required hot-working.

Jan 1, 1962

Provide the U.S. mining industry with a user friendly computer program to calculate stresses in underground coal mines in order to improve safety conditions for mine workers. Capabilities of MULSIM/NL MULSIM/NL (multiple seams, nonlinear) is a three-dimensional boundary-element method (BEM) program developed at the U.S. Bureau of Mines for stress and displacement analysis of coal mines. It can analyze one or two parallel seams that can have any orientation with respect to the Earth's surface. Three main new features distinguish MULSIM/NL from its predecessors: (1) non¬linear material models, (2) multiple mining steps, and (3) energy release and strain energy computations. MULSIM/NL has six material models for the in-seam material: (1) linear elastic for coal, (2) strain softening, (3) elastic plastic, (4) bilinear hardening, (5) strain hardening, and (6) linear elastic for gob. The multiple mining step capability enables the user to efficiently simulate a changing mine geometry. Finally, MULSIM/ NL computes energy release rate due to mining using the most recent concepts advanced by Salamon.

Jan 1, 1993

By Donald O. Capstick

In 1981, U.S. Bureau of Mines personnel conducted a survey of claims and prospects in the Wheeler Ridge RARE II area to determine if mineral resources or potential for resources exists at deposits in the area. Results of Bureau of Mines investigations indicate the area contains no identified mineral deposits. However, the geologic setting at the Round Valley Peak Prospect near the center of the study area is considered to be favorable for the discovery of tungsten resources with associated molybdenum and copper. Tungsten deposits, should they be present, would be expected to occur at depth in tactite at or near the calcareous rock-granite intrusive contact. Sand, gravel, and stone deposits in the area are not considered to be resources because equal or better quality material is available closer to major markets. INTRODUCTION The 16,200-acre (6,560 ha) Wheeler Ridge study area is 11 mi (18 km) northwest of Bishop, California, on the eastern flank of the Sierra Nevada range. The John Muir Wilderness adjoins the study area's western boundary (fig. 1).

Jan 1, 1983

By Oliver Bowles

"The American Consul at Guatemala City reports that the Guatemala Marble Mining Company is preparing to operate a marble quarry about 13 miles from the railroad station of Zacapa, which station is a little over 100 miles from Puerto Barrios, the nearest port from which the product may be shipped. The deposit is extensive, and though somewhat broken up in places, great quantities of sound marble are available. It is claimed that the marble is equal in quality to the best product of the Italian Carrara quarries.Access to the quarry by rail is obtained by a spur track of the International Railways of Central America (Ferrocarril Internacional de Centro America) from Marmol, 3 miles south of Zacapa. This spur is about 5 miles long and terminates at the foot of the mountains. A double-track incline cable-way 2000 feet in length has been constructed to bring the marble down the mountain. From the top of the incline to the quarry there is a railway six miles in length over which the rock will be hauled by two side-geared Shay locomotives."

Mar 1, 1920

By L. C. IlsLey

Figure 1 is a reproduction of a chart recently prepared by the Bureau of Mines at its Pittsburgh Laboratory to show the Bureau's approval work in connection with electrically operated mining equipment. Nearly 27 years of approval work, covering 346 approved units, are shown on this chart. These approvals are arranged according to year of approval and the manufacturer to whom approval was granted. Forty-five manufacturers are represented, and a scheme of using various colored tabs permits the following subdivision of the equipment: Cutting machines, loading machines, conveyors, battery-operated locomotives, battery-operated power trucks, drills and drilling machines, rock-lusting machines, pumps, room hoists, air compressors,, and miscellaneous, The greatest number of approvals granted to a single manufacturer is 80; the next highest is 65, and the third is 49. Several manufacturers have been granted only a single approval. The chart shows all approvals granted for, motored equipment. Some of these units have since become obsolete, and a few are used to a very limited, extent if at all.

Jan 1, 1941

By H. V. Makar

A study was conducted by the Bureau of Mines to determine problems associated with the use of ferrous fractions from urban refuse as melting stock for steelmaking and to evaluate the resulting steel products. The study involved 50-pound ingots from laboratory melts and 50-pound ingots from 1-ton electric-arc-furnace melts. The 50 pound ingots from the laboratory melts and the arc-furnace melts were hot rolled to provide material for mechanical and corrosion testing. Results obtained in the study include the following: Most steels rolled successfully and exhibited acceptable surface and edge condition. Tensile strengths of the plain carbon steels were not significantly affected by copper up to concentrations of 0.65 pct and were not affected by tin content up to 0.16 pct. Yield strength increased with increasing copper and tin contents, and impact strength decreased with increasing tin content. Hardness increased slightly with increasing copper content. In general, properties of the steel produced were not measurably affected by charge composition (that is, melting stock), melting practice, or method of scrap preparation.

Jan 1, 1975

By R. A. Beall

A series of 45 zirconium ingots has been cast by the consumable electrode arc melting process with the object of analyzing the effects of power input from 50 to 230 kilowatts and reduced pressure furnace atmosphere to improve the quality of regular 8-inch-diameter production ingots made thereby. Electrode consumption rate, molten pool volume, melting efficiency, sidewall quality, arc stability, and yield efficiency are considered. The use of direct current and alternating current is studied. In conclusion, reduced pressure furnace operation is shown to promote electrical efficiency, ingot homogeneity, high metal yield, and are stability. INTRODUCTION Zirconium is a particularly difficult metal to melt because of its affinity for atmospheric gases and its solvent properties when molten. In addition, zirconium sponge as produced by the boll process contains minor amounts of magnesium chloride, which cause severe spattering luring melting, because of these difficulties with zirconium, and its sister metal titanium, near techniques have been developed to permit production of commercial size ingots. Among the more promising is the consumable electrode arc melting method.

Jan 1, 1955

By E. P. Youngman

The mining laws of Russia (Collection of Laws, vol. 7, 1912) are still in force in Latvia. The Free State of Latvia (declared independent on November 8, 1918) is composed chiefly of the Baltic Provinces of the former Russian Empire, which are ethnographically Lettish: The Province of Courland, four districts of the Province of Livonia, and three districts of the Province of Vitebsk. Since the establishment of its independence, Latvia has not felt the need of a special mining law, inasmuch as mining so far has not been found profitable in that country. A supplement to this paper, entitled "Mineral Resources," is a brief summary of the minerals found and utilized in latvia. RIGHTS OF FOREIGNERS A foreign individual is permitted to explore for minerals and to own and operate mines in Latvia on equal terms with Latvians. A foreign corporation is required to establish a branch in Latvia, which shall be subject to the corporation laws of the country. A certain number of the partners or incorporators must be citizens of Latvia.

Nov 1, 1931

By Launa G. Mallett, Charles Vaught, Kathleen M. Kowalski, Charles D. Litton, Michael J. Brnich, Ronald S. Conti, Henry P. Cole, William J. Wiehagen

How do people behave when they are trying to get out of a fire? Are escape activities different in each incident, or will most actions be predictable across events? Do persons make the same sorts of decisions whether they are responding as individuals or as group members? Because the social costs of fire-related deaths and injuries are likely to continue to rise, societal pressure for greater safety will also undoubtedly increase. There are, therefore, compelling reasons to further our understanding of action in fires. If human behavior in fire is studied scientifically and predicted according to some well-defined principles, the benefits will be significant. Design engineers could incorporate real-world findings into their plans. Equipment manufacturers could gain from insights into how their technology is actually used in fire emergencies. Safety personnel would have a better appreciation of what constitutes adequate evacuation procedures. Trainers could upgrade the content of their courses that teach escape skills. The result would be an overall improvement in the quality of fire preparedness and safety.

Jan 1, 2000

By A. Dale Marcy, Pamela L. Drake

Workers who perform routine welding tasks are potentially exposed to fume that may contain manganese. Manganese may cause respiratory problems and is implicated in causing the occurrence of Parkinson-like symptoms. In this study, a field colorimetric method for extracting and measuring manganese in welding fume was developed. The method uses ultrasonic extraction with an acidic hydrogen peroxide solution to extract welding fume collected on polyvinyl chloride filters. Commercially available pre-packaged reagents are used to produce a colored solution, created by a reaction of manganese(II) with 1-(2-pyridylazo)-2-naphthol. Absorbance measurements are then made using a portable spectrophotometer. The method detection limit and limit of quantification (LOQ) were 5.2 mg filter-1 and 17 mg filter-1, respectively, with a dynamic range up to 400 mg filter-1. When the results are above the LOQ for the colorimetric method, the manganese masses are equivalent to those measured by the International Organization for Standardization Method 15202-2, which employs a strong acid digestion and analysis using inductively coupled plasma-optical emission spectrometry.

By Joseph E. Chilton, Robert J. Timko, Charles D. Taylor

No regular monitoring of methane is required in areas of gassy coal mines outby the mining face. Methane ignitions that have occurred in mine outby areas indicate the need to provide better protection to workers. Handheld methane monitors are now used by some miners to make periodic measurements of methane at the working face. The IYONI II gas detector which is incorporated into a miner’s cap lamp and worn on a miner’s helmet can continuously provide an alarm signal whenever methane levels exceed a set level. Tests were conducted to evaluate the performance characteristics of this methane detector by measuring response times with methane gas supplied through a calibration fixture or adaptor. Other response time tests were performed with the detector in an environmental test box. Performance was also evaluated in a full scale test gallery where face methane emission and underground ventilation were simulated. Procedures for calibration by response time measurement of the IYONI II detector have been developed. In limited testing, the IYONI II detector was found to reliably detect the presence of 1 percent by volume methane.

By Robert J. Timko, R. Lincoln Derick

This U.S. Bureau of Mines study examined spontaneous heating episodes in coal mine pillars in an active underground coal mine. The information obtained from these incidents was then analyzed to learn which sampling methods provided the earliest indication of pillar heating. The objective of this study was to discover if the location of future events of pillar spontaneous heating could be inferred from the available information. The spontaneous heating-prone area in this evaluation involved pillars located just in by the mine portals. Several detection methods were used to determine gas levels outside as well as inside the affected pillars. It was hoped that, by incorporating external and internal sampling methods into an organized program, locations undergoing spontaneous heating could be determined more readily. This study found that by drilling small-diameter boreholes into the pillars, then obtaining gas samples from the affected pillars, the ability to locate early spontaneous heating episodes was improved. However, the ability to accurately predict future spontaneous heating events remains in question.

Jan 1, 1995

Reduce respirable dust in coal preparation plants. Approach Survey a representative sample of coal preparation plants to (1) determine the dust problem extent, and (2) evaluate practical dust control techniques. Coal Preparation Plant Survey Results Of the approximately 500 coal preparation plants in the United States, 18 plants in six States were randomly selected for survey. The raw hourly capacities ranged from 250 to 1,250 tons, plant construction dates ranged from 1037 to 1982, and usually 3 to 10 workers were required per shift. Respirable dust concentrations within the plants surveyed ranged from very good (less than 1 mg/m') to very poor (14 mg/m3). No relationship was found between dust concentration and age or capacity of the plant. Six of the plants had long-term respirable dust concentrations between 7 and 14 mg/m' in specific areas; six had concentrations between 2.2 and 6.2 mg/m'. Except fur ventilation, only 4 of the 18 plants used operating dust control devices with mixed effectiveness.

Jan 1, 1989

To reduce the possibility of injury to operators and damage to equipment caused by collision of mining vehicles during coal loading. Approach An energy-absorbing bumper was developed and tested underground on a continuous miner. How It Works The bumper, a long box-like weldment backed by five energy absorbers, is attached to a continuous mining machine by a hinge behind the cab. See Figure 1. When a shuttle car collides with the bumper, or when it is otherwise struck, the energy absorbers are compressed. This absorbs and dissipates part of the kinetic energy of the colliding vehicle, thereby reducing or eliminating its destructive effects. Each energy absorber consists of two chambers separated by a freely-moving piston. One chamber (Figure 2) contains hydraulic fluid. The second chamber contains a gas. When a collision causes the absorber to compress, the hydraulic fluid in the first chamber is forced past a metering pin and through an orifice. The hydraulic fluid then pushes against the piston, compressing the gas in the second chamber.

Jan 1, 1978

By W. K. Overbey

Knowledge of fracture systems in oil or gas reservoirs is essential to the efficiency of both primary and secondary production operations. A relationship was established between structural features of the surface and both natural and induced fractures in oil and gas reservoirs, thus providing a method of predicting the direction of rock fracture prior to field development and well completion. Correlations between the surface features and under-ground fractures resulted from analysis of joint strike measurements, bottom-hole impression packer surveys, photographs of hydraulically fractured wells, fracture data from oriented cores, in situ strain measurements from formation outcrops, and lineament analyses from aerial photographs. The mean orientation of surface fractures, lineaments, and stress field directions ranged from N 53° E to N 73° E, compared with an average orientation of N 63° E for the hydraulically induced fractures. Tectonic stress field was shown to influence the direction of hydraulically induced fractures. This report presents the details and application of techniques to obtain the orientation of the principal horizontal compressive stress field component and thus the direction of induced fractures.

Jan 1, 1971

Improve the safety and reduce the cost of longwall entry support. Approach Replace the conventional wood cribbing with stronger, non-rotting and lower cost cribbing made of steel-fiber-reinforced (SFR) concrete. How It Works Conventional concrete can suddenly fail under excessive compression loads, but adding steel fibers to the concrete, before it is mixed with water, changes the failure mode to a gradual and controlled failure characteristic similar to wood. A system for making SFR concrete crib blocks was designed and developed (or use in constructing walls and cribs to support coal mine roofs. The SFR concrete cribbing is stronger and stiffer than wood, and avoids wood's disadvantages of: flammability, deterioration under chemical or bacteriological attack, methane generation, and relatively high cost. Use of SFR concrete also allows freer movement of miners, equipment, and ventilation air, because much less volume of SFR concrete is required than wood for a given amount of support, and because the roof-to-floor closure is greatly reduced by the stiffer supports.

Jan 1, 1981