Search Documents

This is an audience, I know, that shares my interest in a subject that is currently getting a lot of attention -the tendency of our Nation to draw increasingly on overseas supplies of certain mineral commodities, and proportionately less on domestic sources for these minerals. That we do obtain substantial quantities of some essential minerals from abroad is easy to demonstrate. That we will continue to do so in the foreseeable future is not in doubt. Uncertainty begins, however, when we try to interpret the significance of these facts. As with many phenomena, their meaning is open to a variety of interpretations.

Jan 1, 1980

By R. Hogg

"Agglomeration processes and agglomerate characteristics are largely controlled by the forces of interaction between particles. The nature and typical magnitude of these interaction forces are evaluated relative to the external forces commonly present in agglomeration systems. The specific roles of the interaction forces in the various stages of agglomerate formation and growth and their effects on the integrity and mechanical strength of agglomerates are briefly reviewed. Because the interaction forces affect different aspects of agglomerate development in different ways, conflicting requirements can arise. Examples of such conflicts are given and used to demonstrate the importance of evaluating the effects of interaction forces etc., in the context of the overall agglomeration process and its ultimate objectives.INTRODUCTIONThe term agglomeration is generally used to refer to processes whereby discrete particles are caused, or allowed, to associate into clumps in which the individual particles retain their identity but are held together by relatively weak, usually physical forces. Various other designations are given to these processes, depending on the specific circumstances under which agglomeration occurs. The terms balling and pelletizing are often used to describe agglomeration in dry or semi-dry powders; coagulation and flocculation are used to refer to agglomeration of particles dispersed in fluids. Common to all of these cases is the fact that the formation, growth and integrity of the agglomerates depend primarily on the forces acting on and between particles. The same forces are, of course, responsible for manyaspects of the behavior of colloidal systems and their study and evaluation constitute the,basis for colloid and interface science.FORCES ACTING ON FINE PARTICLES AND AGGLOMERATES It is convenient to classify the forces acting on and between particles into two general types: external forces and interaction forces. It should he recognized, however, that a sharp distinction is not always possible.External Forces Gravity and inertial forces act on all particles and their magnitude is proportional to particle mass, i.e. they vary with the cube of particle size. Such forces are oftensignificant for large agglomerates but may be negligible for individual, fine particles.Hydrodynamic (""drag"") forces are important, for particles suspended in fluids. For very small particles, the drag force is directly proportional to size (Stokes' Law) while for very large particles or agglomerates it varies with approximately the square of size (Newton's Law). A useful procedure for estimating drag forces over a broad range of particle sizes and physical conditions has been given by Concha (1)."

Jan 1, 1989

By John W. Frey

This paper presents one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Persia has been prepared from the best available information in Washington but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers , to whom it is being referred through the courtesy of the Department of State .

Nov 1, 1929

By S. Gallagher, A. Mayton, R. Merkel

The prolonged exposure of equipment operators to shock and whole-body vibration (WBV) IS linked to cumulative back, neck, and abdominal disorders. In low-coal mines, space restrictions make seat suspensions difficult to use in isolating operators from shock and WBV. Researchers at NIOSH, Pittsburgh Research Laboratory, are responding to these issues by investigating viscoelastic foams. For the full-load case. an ergonomic seat with viscoelastic foams isolated the shuttle car operator from shock at 15 Hz. Researchers used results from additional foam testing with an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

By T. Bajpayee, L. Prosser, A. Iannacchione, G. Esterhuizen

Reducing the number of roof fall injuries is a goal of the NIOSH mine safety research program. Central to this effort is the development of assessment techniques to help identify the nature of the risks associated with working under potentially hazardous roof conditions. This paper discusses a method to determine the roof fall risk using a qualitative risk-analysis technique. The ability to determine roof fall risk has been a long-standing goal of safety professionals and could provide the kind of information needed by on-site personnel responsible for worker safety to mitigate roof fall injuries.

By Lauren Roberts, Lewis Martin, John Goris

The Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health (NIOSH) and Thiessen Team USA, Spokane, WA, have developed a pull claw that can be attached to any accessible friction bolt ring to test the performance (i.e., load-carrying capacity) of bolts without the use of a pull collar. This would allow true random testing of friction bolts, which need to be evaluated to determine if they are still providing an adequate level of support months or years after installation. Such support is critical to maintaining safe working conditions for underground miners.

Jan 1, 2004

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

By G. E. McElroy, D. Harrington

The use of shall electrically- driven fans , in conjunction with air- pipe of various diameters is becoming of increasing importance for the ventilation of working places in metal mines through which the general ventilating currents can not be coursed . It will probably continue to increase in importance since the concept that air motion is the most important factor in maintaining comfort in hot ( above 80° F . ) working places is more generally accepted , and as the inefficiency and greater expense of attempting to ventilate such places with compressed air is recognized . Managers of large properties can afford to experiment with fan- pipe installations until types are found that meet their conditions , but managers of shall properties , unless forced to it by extreme conditions , prefer to wait until they can obtain data sufficient to guarantee at least a measure of success from such installations . At present , such data , even in part , are available to only a few (mainly fan manufacturer's representatives , consulting ventilation engineers , and ventilatin engineers employed by large companies ) , and important recent developments are mostly of a confidential nature . One large metal - mining company cooperated with a fan manufacturer in some extensive experimental work on small blowers and found that instead of using stock fans , considerable power economy could be effected and equal quantities of air delivered by use of or 2/3 width fans with small motors rather than using stock fans and larger motors ; it was also found advisable to adopt certain sizes of tubing for certain lengths of run . In fact , many important facts were ascertained in this study , and it is now promised that they will soon be given to the public . It is true that a certain amount of data on industrial installations are available , but such data are only in part applicable to metal -mine conditions , because , until recently , little attention has been given to ventilation in metalmines , and the conditions encountered usually require a greater length of pipe , a more temporary type of construction , and closer attention to temperature control than the ordinary run of industrial installations demands ..

Feb 1, 1922

By John M. Dower, Ralph W. Plummer, Terrence J. Stobbe, Hyunwook Kim

"The relationship between exposure to coal mine dust and the development of various respiratory diseases is well recognized. The cause of these diseases however. Is still uncertain. To study this cause-effect relationship, It Is necessary to characterize the coal mine dust In terms of the quantity of dust present and mineral content of the dust. Dust samples were collected using a Portable Continuous Aerosol Monitor (PCAM) and 4-stage cassette Impactors at various locations in an upper Freeport seam coal mine In West Virginia. The samples were analyzed using an X-ray microdiffraction film technique and energy dispersive scanning electron microscopy. This paper presents the results of the first phase of this characterization work which Includes determining the size distribution of the dust and the mineral content of the size intervals.IntroductionDiseases associated with dusts in coal mine environments continue to afflict miners in today's modem mines. These diseases still persist because, as Olishifski points out an employee rarely experiences exposures to a single environmental stress but rather to an Intricate Interplay of multiple stresses.(1) In the case of coal mining the multiple stresses are varying sizes of dust particles originating from coal imbedded minerals. Immediate roof strata bottom strata. Incombustible rock and the coal itself. The site of this Intricate Interplay Is the miner's lungs and the resulting diseases are a function of the composite dust exposures.The proper study of coal mine dust toxicity requires that the dusts used replicate existing coal and mineral dust compositions in their relevant size fractions. The purpose of this project is to develop the size and mineral content data necessary to support this ongoing toxicological effort.Existing coal mining standards and regulations also address total and respirable dust exposures. These dust terms refer to both the quality and quantity of the dust segment in the mine atmosphere. Dust quality addresses its coal and mineral content. whereas dust quantity Is described by mass per unit volume (mg/m3) The comprehensive characterization of coal mine dust exposures will enable revision of these standards and regulations to address the specific minerals and size fractions found to be toxic to human lung tissue."

Mar 1, 1989

By Joseph Cervik

Coal is a soft and brittle material. Drilling rates in the Pittsburgh coalbed using a drag bit exceed 3 ft/min at 2,500-pound thrust. However, maintaining the bit on a horizontal trajectory or parallel to bedding planes to attain lengths of 1,000 feet is difficult. This Bureau of Mines report presents a drill string configuration that can be guided through the coalbed. The angle of the borehole is measured periodically and by proper combinations of bit thrust and rotational speed (r/min), bit trajectory can be lifted or dropped to keep the bit in the coalbed. An example of a hole drilled to 2,126 feet is presented to show levels of thrust and rotational speed used to lift or drop the bit, the seemingly unexplainable events that occur, and the strategy used during drilling. Thrust levels during drilling range from 600 to 2,500 pounds. Hydraulic motors powered by a 30-hp, 440-volt motor provide ample power for drilling horizontal holes 2,000 feet long.

Jan 1, 1975

By Frederick L. Hoffman

Miners' nystagmus is the result of a peculiar form of eyestrain, which often results in impairment of vision and a consequent diminu- tion of the wage-earning capacity of the workman. Historically it has been pointed out by Shufflebotham that "This disease was first recognized by Gillett, of Sheffield, about 1854, although no case was mentioned in medical literature until 1861, when the symptoms were described by De Conde, a Belgian physician. Cases were reported by Pepp Müller as early as 1860, by Von Graefe in 1873, and by Bell Taylor, of Nottingham, and by Nieden in 1874. In this country (England) we are indebted to a very large extent to the observations and writings of the late Simeon Snell and for his pioneer work on this many-sided disease; in France Dransart occupies a similar position." In the treatise on "The Effects of Arts, Trades, and Professions," by C. Turner Thackrah, published in London in 1832, it is stated that- The complexion of the colliers, even after the removal of the dirt, is generally sallow and unhealthy. Their eyes, from the swelling of the lids, appear small, are affected with chronic inflammation and intolerant of full light. * Sickness and vomiting sometimes affect persons at their commencing the employ; and many, after a few years' trial, are obliged, by the injury which their health has sustained, and especially by the weakness of their eyes, to leave the mine. According to Greer, an authority on industrial diseases and acci- dents, miners' nystagmus occurs in 5 per cent of all miners, but it is quite probable that the reference is to European coal miners rather than to men employed in all branches of the mineral industry. According to the same authority, miners' nystagmus "is associated with a twitching of the eyelids and with considerable diminution of the range of movement of the eyes, and is particularly liable to occur in patients whose vision is subnormal owing to errors of refraction, especially astigmatism. It causes much inconvenience to those suf- fering from it and prevents them from following their usual occupa- tion as, owing to the movements of the eyes, everything at which they look appears to be in a state of perpetual motion, and in conse-

Jan 1, 1916

This Technical Memorandum Report is a collection of three working memoranda, prepared during the course of our work for the Bureau of Mines and bound together for convenient reference. These working memoranda present preliminary performance estimates, for baseband voice and narrow- band through-the-earth electromagnetic communications systems of principal interest to the Bureau, for operational/emergency mine communications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; and of theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau. The memoranda examine the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, up- link transmissions via a vertical-axis loop antenna, for typical mine depths of 300, 600, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/meter (high) were used; for voice and narrowband, 10-1 for narrowband only. Examples of high, moderate, and low; surface and subsurface; harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data. These feasibility calculations are not intended to serve as definitive and complete treatments, but as a starting point: to establish first-order estimates of the magnitude and variability of transmitter power requirements under different noise, overburden conductivity, and mine depth conditions; to identify relationships, conditions, or frequencies that are likely to limit or enhance system performance; to reveal items requiring further investigation and data still required; and to suggest practical methods for optimizing system performance. These objectives were met by the calculations. Simple experiments to support these calculations can and should be carried out; together with more detailed investigations of specific modulation, coding, noise-suppression, voice-compression and signal-conditioning techniques, aimed at producing through-the-earth operational/emergency mine-communication systems that are not only effective, but practical and economically sound.

Jan 3, 1972

By Thomas M. Barczak

The safety of mine workers depends on the proper installation of roof supports to prevent the ground from collapsing into the working areas of an underground mine. As new support systems are developed, they need to be properly evaluated to make sure that they are capable of providing adequate roof support before they are first used in a mine. In addition to making certain that the supports meet basic safety criteria, the limitations of the support need to be fully defined in order to avoid improper application of a particular support design. The National Institute for Occupational Safety and Health (NIOSH) operates a world-class facility called the Safety Structures Testing Laboratory. This laboratory contains a unique load frame, the Mine Roof Simulator, which is capable of simulating the ground behavior in underground mines for conducting full-scale evaluations of roof support systems. Safety performance testing protocols using the unique Mine Roof Simulator have been developed for both standing roof support systems and longwall shield supports. The purpose of this paper is to describe these test procedures. The protocol for standing roof supports incorporates seven test series:( 1) uniform loading baseline tests, (2) height evaluations, (3) asymmetric loading, (4) biaxial loading, (5) load rate studies, (6) active loading determination, and (7) static loading evaluations. For longwall shields, a four-series test program that accurately simulates in-service conditions on a longwall face is proposed. This test program consists of (1) transfer of horizontal load to the caving shield-lemniscate assembly (zero-friction test),(2) point loading of shield joints due to lateral movement or rotation of the canopy, (3) evaluation of leg socketand leg cylinder integrity, and (4) face-to-waste racking of the shield. In addition, an evaluation of the shield’s hydraulic components will be conducted prior to the performance testing. These protocols will provide state-of-the-art safety performance evaluations of emerging support technologies, as well as a means to assess the safety of both new and aging longwall shields. Hence, this effort will enhance the safety of mine workers by ensuring that critical support elements are properly designed and that aging supports are retired before their support capability is jeopardized.

Jan 10, 2000

By A. T. Iannacchione

Underground stone mining represents an emerging sector for the U.S. mining industry. As this expansion takes mines under deeper cover and as more efficient mining methods are utilized, adequate stone pillar design methods will become more important. It is the purpose of this paper to examine current design practices and to discuss issues for safe mine layouts so that a rational first approach towards balancing the demands for increased production can be weighed against increased risk to worker safety from rib instabilities and pillar failures. Seventy-two stone mine pillar designs were examined. Pillars with width-to- height ratios below 1.5 and subjected to excessive stress levels appear more likely to fail. When width-to- height ratios fall below 1 .O, defects in the pillars, such as through-going discontinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties, and orientation are important factors controlling pillar strength. The influence of discontinuity dip, a characteristic easily identified in the field, was examined so that its presence could be accounted for in developing generalized guidelines for pillar design.

By J. M. Singer

Approximate equations were used to compute the radiant heating of float coal dust by approaching flames for various combinations of particle size, dust path length (flame travel distance), flame temperature, dust concentration, flame speed, and flame length. The computed values of degree of radiant heating and flame travel distance for preheating the coal dust should be useful for estimating the increased fire hazard of different coal dust-flame parameters. Some findings relating to coal mine disaster control are-- 1. Coal dust clouds cannot be preheated to ignition temperatures by flame radiation alone when deflagration speeds are greater than about 10 m/sec. Thus it appears unlikely that radiation alone will cause flames propagating in dust clouds to accelerate to detonation velocities. 2. Small particles in the radiation flame zone caused by burnout and soot formation increase the degree of preheat significantly. 3. The concentration of float coal dust (radii = 3 to 40 microns) for maximum radiant heating usually peaks in the range 50 to 200 mg/liter of air.

Jan 1, 1970

By Charles P. Lazzara, Charles D. Litton, Frank J. Perzak

This U.S. Bureau of Mines report details the results of a series of large-scale experiments where small coal fires were used to ignite the conveyor belt at air velocities ranging from 0.76 to 6.1 m/s. In the tests, electrical strip heaters imbedded within a pile of coal were used to heat the coal to a point of flaming ignition. The flaming coal subsequently ignited the conveyor belt located approximately 5 to 10 cm above the coal pile. During the tests, temperature, CO, and smoke levels were continuously measured in order to determine both alarm time and level as the fire intensity progressed through the stages of smoldering coal, flaming coal, and flaming coal plus flaming belt. Analysis of the data leads to certain conditions of air velocity and sensor alarm levels that are required for early detection of conveyor belt entry fires. Two nomographs are presented, which define sensor alarm levels and sensor spacings as a function of belt entry cross-sectional area and belt entry air velocity.

Jan 1, 1991

By G. A. Brady

Seven samples of Pennsylvania anthracite from the Bottom Ross bed were analyzed and tested to obtain data on cleaning characteristics, proximate and ultimate analyses, specific gravity, grindability, heating value, and ash softening temperature. Ash content of the samples varied irregularly from 9.0 to 34.4 percent, the range being narrowed to an upper limit of 14.8 percent ash by removing impurities dense enough to sink in a medium with a specific gravity of 1.90. Ash content of the sink material with specific gravity greater than 1.90 ranged from 56.4 to 80.4 percent; corresponding specific gravities were 2.095 to 2.534. Volatile matter contents were indicated to be higher for the ash-forming minerals than for the pure coal substance in the various specific gravity fractions of a given sample. Specific gravities of anthracites with compa¬rable ash contents but from different locations in the bed varied as much as 0.06. The grindability index increased significantly with increasing ash con¬tent of specific gravity fractions from all the samples.

Jan 1, 1968

By Wilbur I. Duvall

In a previous report, entitled A Gage and Recording Equipment for Measuring Dynamic Strain in Rock, a control circuit for a drum camera was described. The purpose of this control circuit was to provide a means for firing seismic caps, synchronizing the firing of the cap with the opening of the camera shutters and generating an electrical impulse at the instant of detonation. The operation of this circuit depended on the following two characteristics of seismic caps: (1) these caps contain a bridge, which breaks at the instant of detonation, and, the firing delay time of the cap is a function of the firing current. During the course of the Bureau's studies, considerable difficulty was experienced from "firing hash", i.e., spurious vibrations that appeared on the records at the time of detonation. The cause of most of this "firing hash" was traced to the intermittent grounding of the cap leads at the time of detonation. As the cap leads were still connected to the firing battery, the grounding of the leads permitted current to flow through the rock to the gage and to return to the firing battery through the shield on the gage cables. The intermittent flow of current along the cable shield produced potentials on the gage leads that were recorded as the "firing hash." To eliminate this difficulty, it is necessary to remove the firing voltage from the cap leads the instant the cap detonates. This report supplements the previous report and describes an improved circuit that can be used to fire seismic caps, remove the firing voltage from the cap leads the instant the cap fires, control the firing delay time in the cap, and generate reference signals at the time current starts flowing in the cap circuit and at the time the cap detonates. These reference signals can be used to determine the firing delay time of seismic caps and the time at which the seismic wave is generated by the explosion.

Jan 1, 1950

By A. A. Afshari, D. G. Frazer, C. F. Stanley

"INTRODUCTIONThe primary function of the lung, i.e. gas exchange, occurs in peripheral units termed alveoli• Diagnosis of lung dysfunction ls therefore dependent on techniques to evaluate the status of the peripheral airways. Since these airways and alveoli are very small, it is difficult to determine directly how they function or how the function is changing due to disease. Yet this unde1·standing is critical to the design of instrumentation to detect early changes in lung function due to disease.An interesting hypothesis describing one aspect of small airway function has been proposed by Frazer (1) as gas trapping due to the formation of menisci in the airways. An additional study (2) proposes that the breaking and possibly the formation of these menisci could generate lung sounds, i.e. crackles. These lung sounds were recorded by placing a microphone at the trachea of an excised rat lung. The lung was degassed and then inflated and deflated. At points along the path of inflation, lung sounds were recorded. However, determination of the origin of the sounds was not attempted due to the difficulties induced by contacting the lung st1rface with a microphone.The purpose of this paper is to describe a non-contacting, whole field technique to monitor and describe the movements of the lung surface during inflation - deflation cycles.HOLOGRAPHIC INTERFEROMETRYHolographic interferometry is a full field, non-contacting and non-destructive technique that measures deformations of an object with a sensitivity in the order of the wavelength of light. A laser beam is split, with one beam reflected from an object and the other used as a reference beam. Both beams combine to produce a hologram of the object on a photographic plate. The process utilizes the concepts of interference, i.e. the two wave amplitudes will add at the points where the difference in optical path lengths over the exposure period is zero or a whole number of wavelengths and will subtract at other points."

Jan 1, 1989

By George D. Dub, FREDERICK G. MOSES

The Bureau of Mines, in connection with the investigations of war minerals it conducted, examined the graphite deposits of this country, studied the methods of mining and preparation used, and sought to devise more efficient methods for the preparation of do- mestic graphite, and to standardize the quality of the product. The graphite investigations covered three general phases, as follows: 1. An examination of the deposits in Alabama and other States, and a survey of the methods of mining and preparation used. In this connection methods of sampling and analysis were noted and ex- periments made to determine a standard method of sampling and a rapid but accurate method of analysis. 2. Experimental work on the concentration and refining of domes- tic crucible graphite to improve the quality of the product and to lessen waste. 3. Experimental work in crucible manufacture to determine the properties of domestic flake and the maximum proportions that might be used without impairing the quality of the crucibles. This work was accompanied by photomicrographic study of crucible structure. In this bulletin are presented the results obtained in the first two phases of the work outlined above. The bulletin is in two parts. The first part describes the methods of mining and milling used, suggests a standard method of sampling finished graphite, and de- scribes a rapid and convenient method of analysis developed at the Pittsburgh station of the Bureau of Mines, to which had been as- signed the analytical and microscopic work. The second part describes experiments on the concentration and milling of graphite, which were made at the Salt Lake City, Utah, station. As soon as the reports incorporated in this bulletin were ready, mimeograph copies were distributed to those persons most interested in order to make the results immediately available. The experimental work on crucible manufacture, assigned to the Columbus, Ohio, station, yielded results which were made known to the industry. Á report on this work will be published later as a separate bulletin.

Jan 1, 1920