Search Documents

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

By E. P. Youngman

By a decree of March 14, 1929,5 the President of the Faitian Repub- lic, considering it to be necessary, until the mining legislation of the Republic shall have been revised, to put into effect the mining law of Decem- Der 4, 1860 (relative to mines, diggings, and quarries), by the authority given in article 55 of the Constitution, declared the law of February 14, 1919, to be abrogated and the provisions of the earlier mining law (December 4, 1050) again to be valid. No concessions were granted under the law of 1919. All citations in this paper, unless otherwise designated, refer to the law of 1930.

Jun 1, 1932

By E. Divers

This Bureau of Mines report presents results of an underground evaluation to determine the respirable dust and gas control effectiveness of a combined (push-pull) face ventilation system for coal mines. The system utilizes both blowing and exhaust curtain, continuous miners equipped with radio remote control, and flight conveyors. Bureau of Mines tests showed a 97% reduction in respirable dust concentrations from the usual cab position on the continuous miner to the remote control operator's position. This allowed the remote control operator to be well within, and the usual cab position to exceed, Federal respirable dust standards. Tests utilizing a safe tracer gas, sulfur hexafluoride (SF6), to determine the face ventilation effectiveness of the combined blowing and exhaust system showed that the system also has excellent methane dispersion capability. Where wide entries permit, this combined face ventilation system and use of remote control can be a very effective method for dust and gas control.

Jan 1, 1982

By John B. Gayle

During studies of the various methods for determining and specifying the factors that indicate whether a particular coke is better or worse than other cokes for metallurgical uses, questions arose as to the precision of screen-analysis tests on coke. Although the usual index of precision, the standard deviation of the test result, gives a measure of the precision of these data, the experimental determination of the standard deviation for a particular set of conditions requires tests on a large number of duplicate samples. Because this procedure necessaily involves a great deal of labor, an equation for predicting standard deviations from theoretical considerations has been developed. Results predicted with this equation agree satisfactorily with the experimental values and are applicable to tests on coal, coke, gravel, and other bulk materials.

Jan 1, 1952

By Mary S. Esfandiary

U.S. scientists attempting to maintain continuous surveillance of scientific information are confronted with two acute problems: The steady, even spectacular; increase in the volume of such information and the fact that much of it is published in unfamiliar foreign languages, According to the National Science Foundation, almost one-third of the world's scientific literature is published in languages that are read by less than 5 percent of U.S. scientists. Most scientists in the United States must rely on abstract journals and translations to obtain information on developments in research and investigations conducted in the non-English-speaking countries. However, there are problems involved in procuring suitable abstracts and translations and in obtaining such information as cheaply and rapidly as possible.

Jan 1, 1961

By Jeffrey H. Welsh

This report presents a study on the use of computerized, continuous remote monitoring systems for fire and explosive atmosphere safety in underground coal mines. The effects of these systems on the safety level in mines are investigated, and the relationship between mine safety regulations and computerized, continuous, remote monitoring is analyzed.

Jan 1, 1982

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

By J. N. Van Sant

Lignite mining in North Dakota was begun about 1884 to supply the domestic needs of settlers. Annual production has grown rather slowly but steadily, exceeding 3 million tons in 1950. The western part of the State has lignite reserves, amounting to 351 billion tons, underlying an area of 28,000 square miles. Contour strip mining has almost completely replaced underground mining as the method of production. Lignite is often found under rather shallow and easily removed overburden, and this is the primary reason for the change in mining practice. Current mining operations are conducted where the overburden is 30 to 70 feet thick. Contour strip mining results in high production rates, at present 27 to 56 tons per man-day. These high production rates result in relatively low production costs.

Jan 1, 1959

By H. C. Hamontre

[The Bureau of Mines well-bore caliper was designed to provide an instrument that could be operated through 2-inch tubing, which 'a used particularly in many input wells on water-flooding projects of eastern, Kansas and northeastern Oklahoma. It should find wide application elsewhere under many other conditions where it has not been possible previously to make caliper logs with the larger probes used on other instruments. The caliper has three additional advantages over other instruments of this type: (1) It measures 4 radii (up to 18 inches) 90° apart with an accuracy of ± 1/4 inch; (2) the measuring arms can be opened and closed at will by remote control; and (3) it is run and operated on a single-conductor, armored electric cable (Amergraph, type 1-H-0). The caliper probe is 1-3/4 inches in diameter and approximately 6 feet in length. The electrical control and measuring circuits are encased in a stainless-steel tubular case. Measuring arms, made of 5/16-inch aluminum tubing, are attached near the lower end of the instrument. Distances the arms are extended are indicated t the surface by a meter calibrated to read directly in inches. Depths at which the radii measurements are taken are indicated by a wireline depth indicator on the cable-reeling. The instrument is not affected by pressure or temperature, it can be run open hole or under pressure through a lubricator. This paper describes and illustrates the instrument and outlines the operating procedures. A bibliography at the end of the report gives references to articles and patents on the development and use of other well-bore calipers.]

Jan 1, 1954

By James S. Browning

For the past several years, the Bureau of Mines has conducted laboratory and continuous process development work on weathered mica pegmatites and micaceous schist ores to determine the feasibility of recovering commercial-grade mica concentrates by flotation. The research has resulted in the development of two processes for flotadon of mica: an acid cationic method for recovery of coarse mica, and an alkaline anionic-cationic method for recovery of fine mica. The research indicated that the two processes may be effectively utilized separately or in combination for flotation of mica from weathered pegmatites and micaceous schists. Concentrates containing over 98 percent mica, with recoveries ranging from 77 to 92 percent, were obtained from the pegmatite ores. The micaceous schist ores yielded concentrates containing 95 to 98 percent mica, with recoveries ranging from 70 to 83 percent. Part 1 of this report summarizes the process development work and demonstrates the feasibility of producing commercial- grade mica concentrates. The report also includes details of commercial beneficiation and grinding of .mica.

Jan 1, 1973

By Donald S. Colby

CARBON-BLACK shipments, which had declined in the latter art of 1953, remained low in 1954 until after settlement of the labor strike that occurred in the rubber industry in July and August. The production of new model automobiles in the last quarter of the year spurred the demand for rubber tires and consequently the demand for carbon black. Total shipments of 1,498 million pounds for the year were 4 percent below 1953.

Jan 1, 1958

By Manuel Gomez

A lignite from Milam County, Tex., has been oxidized by air at temperatures from about 27° to 300° C. for varying lengths of time. The oxidized coal was carbonized at 500° C. in a laboratory assay unit, and the products of carbonization were measured and analyzed. The data presented suggest that, as lignite is progressively oxidized, tar yields are decreased and gas yields are increased in a ratio approximating 1:1. It is surmised that tar-yielding structures in the nonoxidized coal produce gas, principally, when the coal is oxidized. Char-yielding structures of the nonoxidized coal give rise to additional water of decomposition after oxidation and pyrolysis. As lignite is subjected to greater oxidation, the gaseous product evolved on pyrolysis becomes almost entirely carbon dioxide. Tar yields decrease with an increased degree of oxidation, so that the reduction in tar yield may be used as a qualitative measure of oxidation. Pilot-plant drying and carbonization, where air is used as the transport gas and where some air is included in the drying and carbonizing gases, induces some oxidation of the coal particle. The short residence time in a fluidized system with reference to the oxidation environment limits the oxidation.

Jan 1, 1956

By Lung Cheng

The Bureau of Mines conducted laboratory tests to investigate the ease of frictional ingition with frozen (nonrotating) conical bits cutting into sandstone. The number of strikes with a new bit to obtain ignition of a combustible methane-air environment was measured. Tests were made with bits tipped with both tungsten carbide and steel at several bit attack angles (angle between bit axis and sandstone surface) and initial tip angles (included angle at the tip of the new bit). Carbide-tipped bits required more strikes for ingition than steel-tipped bits, by a factor of 7 to 10. With a carbide-tipped bit, the number of strikes for ingition increased by a factor of about 3 if the bit attack angle increased by 10° or if the initial tip angle decreased by 10°. During use, abrasive wear of the frozen bit caused a flat surface to form at the tip of the bit, thereby decreasing the tip angle. As the attack angle increased, however, the new bit involved a smaller wear-flat area whereby, abrasive wear was decreased.

Jan 1, 1987

By Jr. Smith

The equilibrium compositions of product gases for mixtures of air with methane, propane, or ethylene at and around flame temperatures are reported. For each hydrocarbon, compositions are given for five fuel-to-air ratios--two lean, two rich, and one stoichiometric--at five pressures, from 1 to 20 atmospheres, and at an ambient temperature of 25° C.

Jan 1, 1965

By P. J. McDonough

The Bureau of Mines designed and tested a hardware-software system for measuring on-line corrosion rates of materials in a rod mill in operation. Currents ranging from 10-6 to 10-3 A and potentials in I-mV increments were converted to a digital signal. The digitized data were frequency-modulated and transmitted from a rotating ball mill to an FM receiver, where they were decoded by computer and then processed in real time using assembly language software. This design approach would allow accurate measurement and control of systems where signals of small amplitude and large ranges are present.

Jan 1, 1988

By W. A. Cole

Underground mining methods at the Gray mine of Tri-State Zinc, Inc., are of special interest because of the low unit costs achieved through use of jumbos and loading equipment mounted un crawler-type tracks and of diesel trucks that haul from the stoping areas to the mill through inclined adits. The operating company, Tri-State Zinc, Inc., is a wholly owned subsidiary of Gold Fields American Development Co., Ltd., the latter being the American branch of New Consolidated Gold Fields, Ltd., a British-owned company.

Jan 1, 1957

By Tobias W. Goodman, George N. Aul, Joseph Cervik

The Bureau of Mines conducted research to degasify a virgin block of coal in the Beckley Coalbed using long horizontal holes drilled in an array from the bottom of a ventilation air shaft. Eight horizontal holes and an in situ pressure hole were drilled in a radial pattern to depths ranging from 418 to 910 ft (127 to 277 m) and 205 ft (62 m), respectively. The investigation showed the shaft was in a basin saturated with water, which resulted in low gas flows from holes. The in situ pressure at 200 ft (61 m) into the coalbed was 79 psig (544.6 KN/m2). The aver- age gas and water flows for the eight holes were 94,100 ft3/day (2,665 m3/day) and 13 gal/min (49.3 l/min) . After 514 days of degasification, 18.7 million ft3 (0.53 million m3) of gas had been drained. Methane face emissions, which were measured as a section advanced toward the shaft, were reduced about 77 pct, emphasizing the value of drainage by this technique. All holes were grouted before the area around the shaft was mined.

Jan 1, 1982

By Jean M. Kenney

Frequencies of haulage-related accidents in metal and nonmetal surface mines for the years 1988 through 1990 were investigated and compared with those of non-haulage-related accidents. This study was part of the U.S. Bureau of Mines program to improve mining haulage safety. Data were obtained through the U.S. Bureau of Mines Accident Data Analysis (ADA) program. The chi-square test was used to compare frequencies of haulage-related and non-haulage-related accidents for each of the following variables: degree of injury, age, total number of years of mining experience, and shift time. Significance was determined for degree of injury between haulage-related and non-haulage-related accidents. Age of injured did not vary significantly between haulage-related and non-haulage-related accidents, but total number of years of mining experience was found to be significant. Shift time for the accident proved to vary significantly between haulage-and non-haulage-related accidents. Events causing injury for haulage-related accidents were tabulated, and the most frequent determinants of haulage-related accidents were identified. Accident descriptions for both fatalities and permanent disabilities were studied, and the primary causes of these accidents were identified. These findings suggest that haulage-related jobs are among the most dangerous when considering accidents experienced by all workers in the metal and nonmetal surface mining work force.

Jan 1, 1993

By D. Harrington

"In at least three out of every four working faces in metal mines there is no attempt made to cause air circulation other than by use of compressed air, and in at least nine cases out of ten the compressed air is released merely by opening, or partly opening, the valve and allowing the compressed air to escape through open air hose used to convey the compressed air to the drilling machines. Usually no blowers are in use during periods of drilling, as the exhaust from the drill provides cool, comparatively fresh air for the driller; however, in some instances, the compressed-air line is provided with a tea connection, which permits taking air for the drill from one side of the tee, and air for ventilation through a separate hose used as a blower, simultaneously with drilling.Table 1 contains temperature and humidity data as to compressed-air blowers from open end of air hose at 36 working places in eleven metal mines of four States, embracing the mining of gold, silver, copper, lead and zinc ores, and at horizons ranging from 500 feet below the surface to as low as 4900 feet.It is noticed that the ordinary air surrounding the worker at the face gives an average wet bulb temperature of 81.7° F. for the 36 working faces, with 84.7° F. dry bulb and 87.2 per cent relative humidity. The average wet bulb tem¬perature of 36 readings at these working faces of compressed air at the end of the,hose as the air issues from the hose was 67.4° F., or 14.3 degrees lower than the average wet bulb readings of the air of the working places; however, the average dry bulb temperature of the 36 readings of compressed air as it issued from the end of the hose was 79.7° F., or only 5 degrees less than that of the general air (84.7°); the relative humidity was 51.1 per cent as against 87.2 per cent for the surrounding air. Readings were taken in five raises, seven crosscuts, ten drifts and 14 stopes.It will be noted that the velocity or movement of the general atmosphere at each of the entire 36 working faces, was found to be practically imperceptible; this might readily be inferred since compressed air is rarely used on blowers if there is adequate circulation of the general air of the place. Where rook temperatures could be obtained readily, they are shown; it is noticeable that the dry bulb temperature of the air of the working place varies little from the rock temperature, and that the dry bulb temperature of the compressed air as it issues from end of air hose varies only a few degrees from the temperature of the surrounding rock; in some instances the dry bulb temperature of the compressed air as it issued from the end of the air hose was higher than the rock temperature or the dry bulb temperature of the surrounding air."

May 1, 1921

By Steven R. Ruggieri

This report documents the work performed and the results obtained during the field demonstration of the Remote Sealing System at the USBM's Jenny Mine near Inez, KY in the Fall of 1978. Although various portions of the Remote Sealing System had been used on a number of prior occasions, the field demonstration at Jenny Mine marked the first use of the complete upgraded system including the use of the inert gas generating system for seal placement and the first application of the new froth foam system. The objective of the field demonstration at Jenny Mine was to demonstrate the complete system by emplacing and evaluating several complete underground seals under conditions representing those of a mine fire situation. Several critical sealing conditions were identified including: ? High entry airflow ? Standing water (1 to 2 ft) in the entry ? Flowing water (150 gal/min) ? Irregular roof ? Sealing a 4-way intersection. Four seals were successfully placed under the conditions mentioned above. The demonstration served to verify proposed techniques to handle these conditions as well as to dispel any doubts about the system's capabilities. As a result of the successful field demonstration, the Remote Sealing Equipment is now under the jurisdiction of MSHA's Mine Emergency Operation ready for a mine fire emergency.

Jan 1, 1980