Search Documents

By J. W. Sterner

The Bureau of Mines conducted studies on four makes of Japanese automobiles, three 1981 and one 1982 model years, received from three manufacturers to determine if their materials composition would present problems to the current technology used to process junk automobiles for metal recovery. One of each make of automobile was hand-dismantled to determine the materials composition. In addition, two nearly identical automobiles of each make were shredded at a commercial operation where all metal products and rejects were collected for analysis to determine metal and nonmetal distribution. The average weight of the four automobiles to be dismantled, less batteries, tools, and fluids, was 1,938.3 lb. The weight was distributed as 1,472.9 lb. ferrous and 115.6 lb nonferrous metals, 275.2 lb combustibles, 72.3 lb noncombustibles, and 2.3 lb electrical components. The dismantled automobiles, less gas tanks, fluids, tools, wheels, tires, and batteries, which were all removed from the automobiles that were shredded, contained an average of 1,389.1 lb ferrous and 101.6 lb nonferrous metals, 305.7 lb nonmetals, and 2.3 lb electrical components. In comparison, materials collected from the shredded automobiles averaged 1,304 lb ferrous metals, 80 lb nonferrous metals, and 341 lb landfill materials. There were no materials used in the manufacture of the late model Japanese automobiles that should present handling or processing problems to the steelmaking or secondary metal recyclers.

Jan 1, 1984

By R. R. Wells

As a part of the strategic mineral program, examining engineers of the Bureau of Mines collected samples several manganese properties in Colorado. As all of the ores were too low-grade to be acceptable to manufacturers of ferromanganese, beneficiation studies were required .to determine the amenability of the ores to concentration. Manganese in the form of impregnations in sedimentary beds is found in the Denver plains area a few miles east of the Rocky Mountain front. Deposits are reported to occur intermittently over a distance of more than 200 miles. The manganese oxides occur in beds of conglomerate or arkosic sand, generally accompanied by limonite. The Manganese and iron oxides,, however, usually are found in separate layers. Three samples were submitted for beneficiation tests, two samples from Buckley Field bombing Yang, Arapahoe County, and one from near Franktown, Douglas County.

Jan 1, 1952

By Thomas J. Peters

In 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 34,310-acre Diablo Mountain (Additional) study area (OR-001-058), in order to evaluate its identified mineral resources and occurrences. The study area lies along the east shore of saline Summer Lake in Lake County, OR, about 145 miles southeast of Bend and 45 miles northwest of Lakeview. The climate is semiarid and temperate, and the study area is almost treeless. Geologically, the (Additional) study area is in a region of fault block-formed mountains and basins, characterized by interior drainage. The area is mainly underlain by unconsolidated Quaternary and Pleistocene lake and playa sediments, which may include subsurface evaporite mineral deposits and resources. Near the center of the eastern margin of the study area are an occurrence of dolomitic limestone of unknown extent, and an area of basalt outcrop totaling 1.5 square miles. A veneer of windblown sand covers about one-half the study area.

Jan 1, 1989

By Milton H. Fies

The dedication of thin building, establishing a station of the U.S. Bureau of vines at the University of Alabama, bristles with significance and challenges the wisdom and courage of the people of this State. Here is united, in common aim, the Engineering School of our State University, recognized for its competency and usefulness, and the Federal Bureau of Mines. The Bureau is one of the most effective arms of our National Government. It outranks in accomplishment, measured by practical scientific contribution, any like governmental organization in all the other nations. It possesses none of the characteristics of many other bureaus of government which have created popular bias. Here is one Bureau devoid of political suggestion or aim with a personnel zealously devoted to labor in scientific re¬search - an organization marked by practical accomplishment, alleviating many of life's burdens, raking easier life's pathway, and unerringly pointing to life's possibilities.

Jan 1, 1936

By F. W. Wood

The method described may be used to delineate irregularities, inclusions, porosity, or shrink holes in ingots up to 43 inches in length. Rou¬tine testing does not require technical personnel, and the equipment is easily maintained. INTRODUCTION For a number of years, the Northwest Electrodevelopment Laboratory of the Bureau of Mines, Albany, Oreg., under contract with the Atomic Energy Commission and the Naval Reactors Division of the Bureau of Ships, has studied the production of zirconium and has adopted the Kroll magnesium-reduction process3/ as the, most economical means of producing high-purity zirconium sponge in quantities commensurate with demand. Consumable-electrode arc melting4/ provides a practical means of melting the sponge without increasing the impurity content. The ultimate application for which the metal is intended requires that strict specifications be met to insure workability and maintain the nuclear properties and corrosion resistance. The control measures employed to satisfy these specifications include chemical, spectrographic, and metallographic analyses, mechanical and corrosion tests, and ultrasonic inspection of the finished ingot. The primary purpose of ultrasonic inspection is to augment the other control measures by checking the soundness of each ingot leaving the laboratory. An incidental but important function has been the revelation of information leading to better understanding of the arc-melting process. For example, information obtained through ultrasonic inspection relative to the occurrence and distribution of porosity in ingots has resulted in a. modification of melting practices that minimizes the occurrence.

Jan 1, 1955

By Daniel T. Rogers

The Bureau of Mines, in its alumina miniplant project to investigate alumina recovery from domestic, non bauxitic ores, has conducted research on the use of a hydrochloric acid leaching, gas sparging crystallization technology. An important element of this research is the efficient separation of undissolved, siliceous residue from AICI3 -bearing leach liquors by continuous, horizontal, countercurrent vacuum belt filtration. In an effort to calculate material balances quickly and to predict material balances based on different belt filtration configurations, the perfect-mixing-cells-in-series model (PMCS) for calculating material balances around belt filters was used. Because of the porous nature of the solids, the model produced erroneous material balances. Therefore a reliable model, the shrinking voids model, was developed postulating the presence of an unwashable voids liquor volume that decreases with decreasing liquor AICI3 concentration. This volume decrease postulation is equivalent to assuming that dilute liquors flow more freely, causing more voids liquor volume to become washable. Least-squares based computer programs are provided, which are useful not only in producing material balances from plant data but also in predicting balances for untested configurations using the same feed materials.

Jan 1, 1982

By Dennis A. Hansen

The solubility of anhydrous aluminum chloride in solutions of titanium tetrachloride and vanadium tetrachloride was determined as part of a re-search project-by the Bureau of Mines to make a homogeneous alloy sponge of titanium, vanadium, and aluminum. Solubility curves were established using an autoclave at 75°, 100°, 125°, and 150° C. The solubility of AJC13 in TiC14 is 0.2 wt pct at 75° C; it increases to 18.3 wt pct at 150° C. The data concur with data from earlier researchers of this bi-nary system for 75° to 125° C. For the VC14-AlC13 binary system the solubility of AlC13 is 0.1 wt pct at 75° C, increasing to 1.6 wt pct at 150° C. For the TiC14-AlClrVC14 ternary system the solubility of AlC13 decreases from the values found with a pure TiC14-AlC13 system to the lower values found with a pure VC14-AlC13 system at the respective temperatures.

Jan 1, 1986

By K. K. Kershner

Nickel having a purity of more than 99.99 percent with reference to metallic impurities was electrodeposited at the Rolla Metallurgy Research Center of the Federal Bureau of Mines. The production of high-purity nickel is in keeping with the current trend in technologies for producing metals with lower and lower percentages of impurities. To understand more fully the role to be played by nickel by itself and as a component in many alloys, the element must be in a state of high purity. Procedures are outlined for purifying nickel solutions by precipitating and filtering off impurities. Details are given for using the purified solutions as electrolytes in depositing high-purity nickel. The elecneleposited nickel contained 0.0005 to 0.002 percent each of cobalt, copper, aid iron together with spectrographically detectable traces of aluminum, magnesium, and silicon. The deposits were smooth and dense; the crystalline structure was typical of an electrodeposited metal. Some preliminary experiments for purifying nickel solutions by liquid-liquid extraction are also described in this report. Tests of this type were limited since more encouraging results were obtained by other methods of purification.

Jan 1, 1961

By David J. Kusler

This report describes a primary or direct, continuously sampling, and automatically averaging gravimetric method for analyzing gaseous mixtures of carbon dioxide, carbon monoxide) hydrogen, and (by volume measurement) nitrogen. The gaseous mixture is analyzed by passing it at a controlled and definite rate through a system that permits carbon dioxide and water retained by appropriate absorbents to be determined and the residual-gas volume (essentially nitrogen) to be measured. The accuracy and dependability have been established by comparison with very carefully conducted Orsat analyses. The method was developed for, and has been satisfactorily applied to, the analysis of blast-furnace top gas. It permits relatively attention free operation, using simple and low-cost materials usually found as basic equipment in the analytical laboratory. It provides, over a wide range of time or sampling intervals (from less than 1 to over 24 hours), the average composition, in terms of volume-percent, for those components usually determined in blast-furnace gas, if (as is usual) the flow rate of gas from the blast furnace is essentially constant over a selected analysis interval. Oxygen and methane are not determined; but, since these gases are normally absent or present only in traces, their analysis is seldom required.

Jan 1, 1959

By T. SPOLAN, G. W. Jones, R. E. Kennedy

Information relative to the explosibility of acetylene at elevated pressures and means of handling acetylene safely under these conditions is of considerable interest at present. American practice limits the pressure at which acetylene may be generated and distributed to poiIits of' use. The pressure in portable acetylene generators is 15 pounds per square inch gage. Tests made by the Bureau of Mines have shown that 15 pounds per square inch gage is too high to prevent explosiofiS of gaseous acetylene in the absence of air; in fact, dry acetylene gai can be exploded at pressures greater than 5.9 pounds per square inch gage. The Bureau has been interested in the explosibility of acetylene for many years because of its continued: use for illumination in many metal mines and its general use in cutting 1illd~--eldifigoperations in the mining maus-try.

Dec 1, 1948

By O. W. Terry

The Skene mine, in the Elizabeth District, Illinois, produced lead are from 1901 to 1907. Three exploratory holes drilled just north of the mine were said to have penetrated 40 feet of good zinc are. During the summer of 1944, the Bureau of Mines drilled check holes close to what appeared to be two of the three old holes. They also drilled two holes to the south of the mine and one into the core of the deposit. Results of the investigation are given in this report.

Jan 1, 1948

By Robert H. Ridgway

This paper presents the results of the second in the series of annual canvasses on the consumption of ferrous scrap and pig iron in the United States, inaugurated in 1935 by the Bureau of Mines and published in Report of Investigations 3329. The study was undertaken in response to requests from trade organizations and others for detailed statistics on this phase of the iron and steel industry. Thus, for the first time, producers, buyers, sellers, and consumers of iron and steel scrap have had an accurate statistical picture of this important raw material As originally contemplated, the study was to be continued on an annual basis, but, owing to budgetary limitations for the fiscal year 1937-38, the Bureau may be unable to conduct the canvass for 1937.

Jan 1, 1937

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook (Volume III) contains overall injury experience for coal mines, both anthracite and bituminous coal, coke plants, petroleum and natural gas, peat, and asphalt and related bitumens (native); metal mines, metallurgical plants, including ore-dressing plants and primary nonferrous reduction plants and refineries; nonmetal mines; nonmetal mills; sand and gravel operations; slag (iron blast-furnace) plants; and stone quarries and their related plants. Volume I of the yearbook contains a chapter showing injury experience and employment data treated separately by categories: Metal mines, nonmetal mines, quarries and their related plants, metallurgical plants (ore-dressing plants and primary nonferrous reduction plants and refineries are shown separately), nonmetal mills, sand and gravel plants, and iron blast-furnace slag plants. Volume II contains injury and employment experience in the fuel industries (anthracite, bituminous coal including lignite, coke, petroleum and natural gas, native asphalt and related bitumens, and peat). Injury and employment data were collected from coal producers on the regular mandatory basis as required by the Federal Coal Mine Safety Act (30 U.S.C., sec. 455). Similar data for 1962 from metal, nonmetal (except well and brine operations), stone, and sand and gravel producers were collected by a. mandatory reporting system under the provisions of the Act of September 26, 1961, Public Law 87-300 (75 Stat. 649). Before 1962, these nonfuel producers reported voluntarily to the Bureau of Mines. Producers of all other minerals (fuel and nonfuel) reported the requested injury and employment data voluntarily to the Bureau for 1962, the same as in preceding years.

Jan 1, 1963

By Seth C. Schaefer

The Bureau of mines investigated thermodynamic properties of MnSO4 and 2CdO CdSO4 to obtain basic thermodynamic data applicable to the treatment of mineral concentrates during roasting and sintering processes. Standard Gibbs energies of formation were determined with high-temperature galvanic cells using stabilized Zr02 as the electrolyte. Potential measurements were obtained from the cells?

Jan 1, 1983

By J. R. Cobble

Dissolution of chalcopyrite with acidified ferric sulfate produces a sulfur layer on the unreacted chalcopyrite surface that interferes with further dissolution. The U.S. Bureau of Mines has developed a process to improve the leaching kinetics of these types of diffusion-controlled systems. The system features the Bureau-developed turbomill, an attrition grinder that scrubs the reaction product coating away from the unreacted mineral grains during leaching. The system can be operated continuously at any temperature up to the boiling point of the leaching agent. This method is a hydrometallurgical alternative to chalcopyrite smelter technology and eliminates sulfur dioxide emission problems with its associated costs. Batch testing at 900 C with the chalcopyrite-ferric sulfate system resulted in copper extraction exceeding 99 pct. At an optimal energy consumption of 1,520 kW· hjst, 95 pct of the copper was extracted. The pregnant liquor was clarified and tested for typical solvent-extraction recovery of the copper. Two-stage extraction and two-stage stripping recovered 96 pct of the copper in an electrolyte suitable for copper electrowinning.

Jan 1, 1993

By William O. Vanderburg

This paper describing the methods and costs of milling scheelite ore at the Silver Dike concentrator of the Nevada-Massachusetts Co., Inc., is one of a series being prepared by the Bureau of Mines. In the Silver Dike mill tungsten ore which contains about 1 per cent of scheelite is treated at the maximum rate of 45 tens per 24 hours by tabling followed by magnetic separators to clean the table concentrates. Unusually high-grade concentrates are produced which average between 70 and 75 per cent of W03.

Jan 1, 1932

By L. C. IlsLey

The cool drills that have received the approved of the Bureau of Mines may be divided into three general classes: (1) Hand drills, small drills that are held in the hands or supported against the body while in use; (2) post drills, drills that are too heavy or powerful for hand operation and therefore require some mechanical mounting when in use; and (3) drilling machines. Besides these three classes, drilling equipment has been incorporated in the design n of a number of permissible coal-cutting machines, but such drills are considered an integral part of the cutting machine and are not given separate approval. The hand drills have been described in Report of Investigations 3363, which is cite of several papers that have been published dealing with miscellaneous types of permissible motor-driven mind equipment not covered in bulletins. The present paper describes post drills and drilling machines approved by the Bureau of Mines up to July 1, 1937.

Jan 1, 1938

By L. C. IlsLey

[The cool drills that have received the approval of the Bureau of Mines may be divided into three general classes: (1) Hand drills, small drills that are held in the hands or supported against the body while in use; (2) post drills, drills that are too heavy or powerful for hand operation and therefore require some mechanical mounting when in use; and. (3) drilling machines. Besides these three classes, drilling equipment has been incorporated in the design n of a number of permissible coal-cutting machines, but such drills are considered an integral part of the cutting machine and are not given separate approval. The hand drills have been described in Report of Investigations 3303, which is cite of several papers that have been published dealing with miscellaneous types of permissible motor-driven mind equipment not covered in bulletins. The present paper describes post drills and drilling machines approved by the Bureau of Mines up to July 1, 1937.]

Jan 1, 1938

This publication summarizes the research (in-house and contract projects) programmed by the Bureau of Mines for fiscal year 1984 (October 1, 1983-September 30, 1984) under its Health and Safety Technology Program. The objective of these projects is to provide an ordered and sequenced advance toward the Bureau's overall goal of providing the systems technology required to create a more healthful and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1983

By C. M. K. Boldt

This report summarizes five separate Bureau of Mines contract studies on the use of aerial photogrammetry, satellite transmission of in situ instrumentation information, and satellite imagery to monitor and update mine waste embankment data. The equipment used, methods applied, results, recommendations, and cost analyses are presented along with a bibliography of related investigations.

Jan 1, 1987