Search Documents

By Terri Jordan, Gregory Hempen, Thomas Keevin

Water-borne blast pressures from confined blasts were recorded as part of a submerged blasting program in Florida for channel deepening. The blasting was confined within the rock floor by stemming. Shot patterns of stemmed borings were recorded, as were two open-water shots. One hole of one shot was not confined properly, which allowed comparison of confined and a poorly confined larger charge weights per delay. The pressure data were intended to gain information on typical pressure measures from the rock removal program relative to impacts on marine organisms. Water-borne pressures from actual confined, rock-removal shots validate the hypothesis of lessened impacts to aquatic and marine biota.

Jan 1, 2007

By Travis A. Davidsavor, David A. Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines.

Feb 1, 2020

By Travis Davidsavor, David Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines. Existing pipeline company standards would have effectively precluded the construction of the replacement pipe by blasting rock. To facilitate the required construction and evaluate actual pipe stress during blasting to ensure pipeline integrity, a comprehensive evaluation methodology was developed by a team of pipeline, mechanical, geotechnical, instrumentation, and blasting engineers. A total of 60 strain gages were affixed to the steel pipe and seismographs were buried at the surface near the blasting area. Test blasting allowed pipe stresses with corresponding ground motion to be monitored. A conservative analysis approach evaluated individual peak strains and revealed that only small pipeline strains, and therefore stresses, were induced in the pipeline as a result of blasting. This evaluation allowed specific procedures to be developed to inform the blasting operation of maximum explosive loading and minimum charge distances. Additionally, this effort provided the pipeline operator with appropriate pipeline operating pressures during blasting activities to limit total stresses in the pipeline to be below allowable stresses imposed by code, regulators, and company operational limitations. Recommendations were developed to measure the blast generated ground vibrations with seismographs buried at the depth of the pipe, near the pipe, and limit the ground vibrations from blasting to 150 mm/s (6 in/s). If ground vibration intensities of 120 mm/s (4 in/s) or more were observed, additional engineering review is recommended. Finally, all blasting would be suspended and all activities reviewed at peak ground vibration intensities of 230 mm/s (9 in/s). The evaluation effort resulted in effective and efficient construction of the pipeline replacement and allowed the pipeline operator to better understand blasting induced stresses on their assets.

By R. Hazael, R. Alford, R. Critchley

The ability to compare explosives is fundamental. Numerous methods are used and while simple conversion factors are often used, the use of TNT Equivalency (TNTe) is not a simple subject as explosives exhibit very different equivalencies depending on whether the pressure or impulse are being considered as well as other conditions. The scaled distance has been found to have a significant effect on the TNTe but due to the difficulty of taking measurements at very close ranges, no TNTe have been quoted for charges in direct contact (Z=0). This paper describes the use of a ballistic pendulum to measure the impulse from contact charges and presents some surprising results that require a two-stage propulsion, as originally described by Backofen, to be explained.

Jan 1, 2024

By Rachel L. Bauer, Catherine E. Johnson

Explosive demolition involves first, the use of cutting charges to sever a column and second, kicker charges to move it out of alignment. Dynamite is the traditional explosive used in kicker charges as it is inexpensive, easy to initiate, and has a consistent track record of use. Dynamite, however, has health concerns in handling, fragmentation concerns from direct contact on the beam, and availability concerns due to being manufactured at only one location in the continental United States. Recently, water-cased kicker charges have been used in industry, and research has shown that a reduced dynamite mass is possible due to the added confinement, for energetic performance, and the incompressible fluid, which aids in the transfer of explosive energy into beam movement. This research will compare two different explosives, an emulsion (DYNO AP), and binary (HELIX), to dynamite for use in kicker charges, both with and without water-casing. Emulsion is commonly used in rock blasting to create a large push or throw due to its high gas volume production which could translate to kicker charge movement. HELIX is a binary explosive commonly used by the military in breaching charges with water backing. Experimental tests placed kicker charges at the base of a hanging steel column, modifying the ballistic mortar test used to determine explosive power. The study shows that water-casing effectively reduces air overpressure and enhances explosive performance. Among the tested explosives, HELIX showed the most substantial improvements with a 1.8 dB reduction in air overpressure and a 3.2 m/s (10.5 ft/s) increase in column velocity when water-cased. Dynamite and emulsion also benefited from water casing, with decreases in air overpressure (1.1 and 0.7 dB respectively) and increases in column velocity (1.1 and 0.7 m/s (3.6 and 2.3 ft/s) respectively). This research also shows that emulsion is a viable replacement for dynamite in demolition projects, performing similarly in both traditional use and water-cased charges.

Jan 21, 2025

By Clarence Hall, Charles E. Monroe

Squibs, Fuse, and Detonators It has been made clear in the discussion of combustion and explosion and the description of various explosives that they can be caused to explode by various means. All of them can, under some circumstances, be made to explode by fire. Some of them can be caused to undergo a detonating explosion by setting off a detonator in contact with them. In blasting use is made of both these means for setting off explosives, the means used being determined by circumstances.

Jan 1, 2010

By Keith Maki

This paper details a simple substitution of precise electronic timing in the holes for standard pyrotechnic delays. In addition, we wanted to use two electronics in bottom and top to test the colliding shock wave theory. It also discusses the difficult loading conditions on the Iron Range of Northern Minnesota. No preliminary analysis (Signature Hole waveform analysis) was done to determine the most favorable blast timing for fragmentation increase or vibration reduction.

Jan 1, 2007

By Alyse Munro Hindley

The increasing negative public opinion toward blasting has led to stricter regulations and increased costs. This paper outlines alternative methods of rock excavation and the safety regulations and certification required by blasting professionals. Most importantly, however, it showcases the benefits and accomplishments that controlled blasting bring to society, giving the public a better understanding of the necessity of blasting in modern society.

Jan 1, 2015

By William Hissem

The topics in the title line of this article are desirable and applicable to entire industries that exist outside the realm of the ISEE’s readership. But the issues I will discuss herein are specific to those who drill, blast, and excavate rock as part of their business. Civil and site construction projects, mines, and quarries specifically comprise the group who will benefit from this discussion.

Jan 1, 2014

By David S. Shatzer, Michael R. Purcell

Current world events have demonstrated the use of commercial vehicles, other unconventional modes of transportation and unusual materials as explosives or incendiary weapons, affecting commerce, disrupting cities and even entire societies. Since the implementation of the Organized Crime Control act of 1970 the Bureau of Alcohol, Tobacco, Firearms and Explosives (ATF) has been investigating and studying explosives and incendiary devices and their related effects.

Jan 1, 2004

By Jeff Dean

As the Society celebrates its 35th year as an explosives industry association, it is clear that we are part of an industry that covers many sectors of economic activity. We are the voice of those who use, transport, store, manufacture, and dispose of commercial explosives products and others that serve the end user of explosives products. Along with other associations in this industry, we have a combined membership of hundreds of companies and tens of thousands of individuals in the U.S. and around the globe.

Jan 1, 2010

By Jeffrey Meissner, Mike Waldron, Charles Dowding

Most studies of crack response have focused on opening and closing of a crack in the plane of the wall in which the crack occurs. Crack movement also occurs perpendicular or normal to the plane of the wall. This paper will examine and compare the in-plane and out-of-plane (normal) response of cracks in two different residences near limestone quarries. In two locations, sensors that measure in-plane and normal displacement were installed side-by-side on the same crack, allowing direct comparison of the two modes of response. In a third location, a perpendicular pair of displacement sensors was installed in a corner of a room to observe the bidirectional response of the structure at a corner. Both long-term and dynamic data were recorded with the same sensors; temperature, humidity, and air over pressures were also recorded to compare blast and weather effects. Measurements show that ratios of out of plane to in plane response to dynamic events can vary. However, the ratios of out of plane (normal) response to vibratory events to that of climatological change is still as small as the ratio for in plane crack responses.

Jan 1, 2010

By Kenneth Eltschlager

Blasting represents the highest risk of any surface coal mining activity that could result in injury and/or property damage off the permit area. In addition, blasting related issues e.g. flyrock, vibrations, air blast, etc., are responsible for a large percentage of citizen complaints. Thorough and consistent regulation of individuals certified to conduct blasting by the Office of Surface Mining Reclamation and Enforcement in Federal Program states and on Indian Lands under Federal jurisdiction is vital, as it serves to: facilitate coal production to meet the nation’s energy needs; protect people and property on and adjacent to Federal mining permits; form a basis for states to grant reciprocity certificates to Federal blasters; and be a positive example to primacy states. OSM issues Federal blaster certificates for blasting on Federal surface coal mine permits. The certification program includes experience, training and testing components similar to many of the states. But where a state program may focus on the specific blasting applications within its boundary, the OSM certificate requires a very diverse test to cover all potential blasting applications and products across the nation. Therefore, the Federal certificate is a good surface mining credential for blasters anywhere in the United States.

Jan 1, 2010

By D. Rudenko, C. T. Aimone-Martin, J. K. Ratliff, I. G. Wong, J. Aiken, R. E. Burnham, T. A. Davidsavor

A small quarry blast was conducted with a maximum of 90 pounds per delay and shortly afterwards, area residents sensed ground motion and building shaking indicative of an earthquake. In addition, seismometers up to 500 miles (800 km) away recorded a magnitude 2.8 earthquake located in the area. Positioned in a seismically inactive area, southern Minnesota is not known for earthquakes. The earthquake was originally described by the USGS to be a surface blast at the quarry. Analysis showed that the earthquake occurred shortly (approximately seven seconds) after the quarry blast some distance away and well below the surface. This paper describes the evaluation of the “seismic events” including the blast, the following earthquake, initial governmental response, and provides the framework for assessing the relationship between the blast and the earthquake. The paper also discusses management of large volume claims from a complex event and presents a claims management strategy with best practices.

Feb 6, 2023

By L D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By K Taylor

Small scale tests have been conducted in blasting vessels in the laboratory, where the effects of explosive composition, charge diameter, explosive confinement as well as additives to the explosive were examined on NO, NO2, CO and CO2 production. Fumes were analyzed continuously using a flue analyzer, providing analysis every 15 seconds. The results were compared to previous work conducted in the laboratory and to literature findings. It was found that the type of the explosive was the most dominant factor with emulsion explosives producing significantly less amounts of toxic gases. ANFO was shown to always produce nitrogen oxides, even when fuel rich. Tests were also conducted by detonating explosives in broken rock, simulating the release of products of detonation during the formation of a muckpile. Products of detonation were affected by the presence of atmospheric air or rock around the charge. Gaseous products of detonation migrated through the rock piles at different rates, resulting in a change of toxicity values over time. In the small scale experiments, CO appeared to travel faster than CO2 while NOX was not identified. Analysis of the gases that were released during digging, several hours after the blast, resulted in high temporary concentrations of toxic fumes.

Jan 1, 2014

By Robert Hopler

THIS paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the headingand-bench system. Much depends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading.

Jan 1, 2010

By Xu Tianrui, Jin Xiang, Pen Dianhua

Based on the results of research or investigation, this paper describes the causes of and countermeasures for unexpected accidents, such as premature, postponed or spontaneous explosions in blasting practices in China.

Jan 1, 1996

By Barbara Rutter, Phillip Mulligan

This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile.

Feb 1, 2020

By Catherine Johnson, Barbara Rutter, Phillip Mulligan

Shock tubes, shock tunnels, and blast tubes have been widely used by explosive researchers and shock wave investigators to understand the characteristics of shock waves. Rectangular, cylindrical, and conical are the three simple geometries commonly used in shock tube and shock tunnel testing. These geometries result in shock waves that resemble the Friedlander curve’s simple exponential decay. However, geometries that are more complex have not been studied. This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile. Shock wave profiles were measured inside and outside the LATS to investigate the geometry’s effect. A representative shock wave profile from each geometry and open-air explosive testing were compared visually showing the geometries effect on the shock wave profile. The LATS produced a waveform with four pressure peaks behind the initial shock front, which were found to be associated with the four rectangular sections. The resulting pressure trace was compared to pressure traces from simulated urban bombings. The number of turns in an urban environment equated to a new peak, which is caused by additional expansion sections of the shock tunnel. From this observation, complex geometry shock tunnels can be purpose built to simulate an explosion in an urban setting. The use of shock tunnels with complex geometry in simulating urban bombings can allow for numerous representations and a better understanding of profiles produced during an urban bombing or similar scenario.