Search Documents

By M. Pötsch, A. Kluckner, P. Söllner, W. Schubert

"The in situ block size is a key parameter in the geomechanical characterization of rock masses. It describes the fracturing of the rock mass and thus is a measure for the degradation of the rock mass strength. Several classification systems use the in situ block size. For instance, the Geological Strength Index (GSI) requires the “blockiness” and joint surface condition factor as key input parameters. The “blockiness” has recently been related to the in situ block volume (Cai et al., 2004). Due to the limited information about the internals of a rock mass, it is not possible to determine the in situ block size directly. Currently, the in situ block size is determined by calculations using oversimplified models, vague estimations or, due to the lack of relevant information, it is neglected. As remote measurement systems have become available for rock mass characterization, a more comprehensive record of discontinuities can take place. Measurements can be performed on exposed rock outcrops and in particular on tunnel faces and walls, delivering the location, orientation, spacing and persistence of discontinuities at an arbitrary number and locations. An estimation of the in situ block size at the same level of sophistication is still not available. This paper aims at examining the relationship between visible and measureable information at the rock surface, and the in situ block size. Three-dimensional block model simulations were performed using the block model engine of the distinct element code 3DEC. Initial investigations focussed on the minimally required observation area in order to obtain reliable block size distributions. Based on a representative volume element, a reference distribution of the block area at the observation area for a specific discontinuity system was determined. Subsequently, the size of the observation area was decreased stepwise and each new distribution was compared to the reference distribution. For all analyzed systems, it turned out that the mean block area must be smaller than 1% of the observation area to achieve a reliable block size distribution. Further simulations focussed on discontinuity systems with three non-persistent sets. The results were compared to the formula proposed by Cai et al. (2004). A transformation factor T was introduced which replaces the persistence terms in Cai et al.’s proposed formula. The factor describes the correlation between block volumes generated by persistent and corresponding non-persistent discontinuity sets. The simulations included the variation of the discontinuity set spacing, persistence, and orientation. The mean and additionally the 25%-, 50%- and 75%-quantiles of the block size distribution were analyzed. Examining all values for the transformation factor the distribution can be described by a power function with a negative exponent. The function depends on the persistence only. Finally, the results of random simulations were compared to the analytical formula using the transformation factor. The predicted mean and selected quantiles show a good agreement with the simulation results. It gives a comprehensive picture about the block size distribution in discontinuity systems with three non-persistent sets."

Jan 1, 2015

By R. E. Whitehead

"The earliest gold-mining operations in Ontario included the Cordova, Deloro, and Sophia mines north of Lake Ontario (see for example, Miller and Knight, 1914). The Cordova deposit, worked intermittently between 1891 and 1940, is reported to have yielded 22 774 oz of gold from 127 670 tons of ore averaging 0.19 oz/ton Au (Gordon et al., 1979). The property remained inactive for many years. In 1988, Gunnar Gold Inc. and Mill City Gold Inc. conducted a drilling program along the main Cordova vein. The present study is based on core from three drill holes through the Cordova gabbro (Fig. 1) and the carbonate alteration zones enveloping the quartz-carbonate veins. The relatively narrow width of the alteration zone and the availability of continuous sections of core provided an opportunity to conduct a compact mineralogical-chemical study of carbonate alteration and its effect on the redistribution of rare earth elements (REEs). Although the Cordova deposit is not of great economic importance, this study has revealed a number of interesting features which are interpreted as resulting from processes that may be applicable to gold-bearing quartz vein deposits elsewhere.The Cordova gabbro is layered in places, varying from fine-to coarse-grained and in color from light gray (feldspathic) to dark gray-green (amphibolitic). However, layering within the section of the gabbro considered here and which hosts the Cordova gold deposit is mainly textural rather than compositional. Samples of unaltered gabbro selected for analyses were medium- to coarse-grained; amphibolitic and anorthositic phases were avoided as being less representative of the general chemical composition of the gabbro.The Cordova intrusion has undergone regional metamorphism and consists dominantly of actinolite and saussuritized plagioclase with smaller amounts of granular clinozoisite and flaky chlorite; minor quartz, ilmenite, titanite, apatite, and calcite are typically present. Some actinolite grains have irregular rims of pleochroic green hornblende that is optically continuous with the actinolite. Both chlorite and clinozoisite occur in two modes. Chlorite occurs as an alteration product of actinolite and as separate grains in the groundmass. Clinozoisite and albite occur together as regional metamorphic alteration products of original plagioclase crystals and as discrete grains in the matrix.The main gold-bearing quartz-carbonate occurrence occupies an easterly trending, steeply southward-dipping carbonatized shear zone up to 15 m wide and 700 m long. The gold occurs principally in irregular lenses and veins of quartz-carbonate up to a foot thick occupying the lower part of the schistose shear zone within the gabbro. This zone consists of chlorite, biotite, and carbonate and is flanked on both sides by chlorite-carbonate schist lacking biotite. The chlorite-carbonate schist in turn grades into regionally metamorphosed actinolite-bearing undeformed gabbro.The dominant sulfide within the quartz-carbonate lenses and in the surrounding schist is pyrite which occurs mainly as small cubes (1 mm to 2 mm) generally making up less than 10% of the rock. Rare blebs of chalcopyrite are present. Magnetite is common throughout the schist."

Jan 1, 2001

By Gerardo Fuentes

Arsenic extraction from Chilean copper concentrates up to nearly 99% was achieved, using hydrothermal reactions. Arsenic appears in nature in more than 200 mineral species, being arsenopyrite (FeAsS), enargite (Cu3AsS4), and tennantite (Cu12As4S13) the most common species. In addition, arsenic is present in a large amount of copper concentrates, produced in northern Chile. Medical statistics show that in northern Chile, the amount of cancer to the lung, skin and bladder are the highest in the country. The latter situation, demonstrates the importance of studying metallurgical processes that do not generate atmospheric pollution. The hydrometallurgical processes such as hydrothermal treatment in autoclave reactors, do not produce gaseous emissions. On the other hand, the arsenic remains in solution from where it can be transformed in scorodite by widely known methods. Previous works about hydrothermal treatment of enargite have shown the feasibility of transforming the enargite of the copper concentrates into chalcocite or mineral species of the chalcocite family such as djurleite, digenite and for this reason enrich the concentrate in copper and pass the arsenic to solution. For this research, two Chilean copper concentrates were used, concentrate 1 with 5.5% arsenic and concentrate 3 with 1.8% arsenic. These concentrates were subjected to a complete chemical and mineralogical characterization. Later these concentrates were carry out to batch tests of hydrothermal treatment. Also, these concentrates were subjected to grinding to have different particle sizes. For the hydrothermal tests, a liter capacity Autoclave Engineer reactor was used. Characteristic of this reactor was the maximum temperature 350°C, 5000 PSI pressure, and 900 rpm agitation speed. Kinetic tests were carried out with the two concentrates maintaining the same solid: liquid relationship, the same agitation velocity and the variables studied were treatment temperature, time of reaction, concentration of copper in the solution and grain size of the concentrates. The conclusions of the study indicated arsenic extraction of the order of 93.98% from the concentrate 1 and arsenic extraction of the order of 98.74% from concentrate 3. After the hydrothermal treatment, the solids and solutions were characterized chemically, by electron microscopy and X ray diffraction. Also the solids were characterized by grainsize through a particle size analyzer (MICROTRAC). Results of batch treatment shows that arsenic can be release almost completely from real copper concentrates using this hydrothermal process and the next stage will be a scale up process in order obtain results for pilot plant design. INTRODUCTION Arsenic is an impurity that appears associated with copper minerals forming enargite, tennantite, tetrahedrite, and that due to the pyrometallurgical treatment either in conversion or roasting furnaces, it goes into the atmosphere together with the sulfur dioxide. A great quantity of literature can be found to eliminate arsenic or try to separate arsenic from copper. The methods used are mainly leaching processes with or without pressure (Padilla, Jerez & Ruiz, 2015) with different reagents like chloride media (Herreros, Fuentes, Quiroz & Viñals, 2003) or chloride media with sulphuric acid (Riveros & Dutrizac, 2008) or sodium hypochlorite (Mihajlovic, Strbac, Zivkovic, Kovacevic & Stehernik, 2007). It is known too that Chile is the first copper producer in the world and a great quantity of its minerals are in the north of the country, in Antofagasta.

Jan 1, 2019

By Paul Stothart

Agenda 1)Key Political and Policy Issues 2)Relevance to the Mining Sector ?All parties vying to be the greenest ?Regulation, indoor air, health issues combined into Clean Air Act ?International carbon markets ?Kyoto Protocol ?legal force ?Spawning clean energy technologies? ?Effectiveness of present approaches?

May 1, 2007

By Malcolm Scoble

School Values ?? Each other; ?? Students, & helping them develop intellectually, personally & professionally; ?? Freedom to pursue educational & research opportunities; ?? Home-work-life balance; ?? The geographic-business community in which we operate ; ?? The pursuit of excellence; ?? Our contribution to society; ?? Creativity & innovation; ?? Teamwork & collaboration; ?? Career development, achievement & reward.

May 1, 2008

By L. R. P. de Andrade Lima, D. Hodouin

The paper presents a survey of the possibilities of the simulation techniques for improving the design and operation of gold processing plants. The procedure to construct kinetic models that are used in simulators is first reviewed, and examples are given for cyanide gold dissolution and gold adsorption on carbon. Then, an overview of the structures of the plant simulators is proposed, and the simulation equations formulated for a carbon-in-leach process. Finally, the potential of simulation methods is illustrated by four examples. The first one shows how it is possible to use a simulator to design a cascade of leaching tanks while optimizing an economic performance criterion. The second one illustrates the role of simulators for optimal tuning of the cyanide addition strategy in a leaching circuit. The third example focuses on the power of simulation to design carbon transfer strategies in a carbon-in-pulp process. Finally, the last example shows the role of on-line simulators for optimally supervising the automatic control of cyanide addition into leaching tanks.

Jan 1, 2005

By T. ?kre, O. M. Dotterud, S. Haarberg, J. Thonstad, G. M. Haarberg

An electrowinning pilot plant has been constructed at Falconbridge Nikkelverk A/S, Kristiansand, Norway. The equipment consists of a mixing tank where the electrolyte composition and temperature are controlled, an electrowinning tank equipped with five cathodes and six anodes of commercial size and design and a dechlorination facility. Electrowinning experiments were carried out in this pilot plant using acid cobalt chloride solution from the cobalt tankhouse. Key parameters were varied to obtain an improved understanding of the cobalt electrowinning process, focusing on the detrimental deposition of cobalt oxide on dimensionally stable anodes. The extent of anode scaling was found to be dependent on the electrowinning conditions. Low pH, temperature and cobalt concentration resulted in less scale being formed, however at the expense of cobalt current efficiency and cell voltage, adversely affecting electrowinning production capacity and energy consumption. When operating at high acidity, pH in the anolyte was higher than in the catholyte, which is believed to be due to H+ ions taking part in the current transport across the diaphragm, migrating out of the bags surrounding each anode.

Jan 1, 2005

By J. Janzen

The cost to supply ventilation may exceed 40% of the total mine energy cost for underground mines and is often higher for deeper mines. The goal of Ventilation-on-Demand (VOD) is to ensure that the required quantity and quality of air is supplied to underground mining crews and diesel equipment at the least energy expenditure (minimum cost). A VOD system may include control of surface fans (Supply & Exhaust), underground booster fans, auxiliary fans and automated regulators/dampers to regulate the flow of air with more control elements providing more value. Strategically located Air monitoring stations measure air quantity and quality and provide feed-back enabling control. The modular design involving controls, intelligent instrument and intelligent motor control centres coupled with a communication network allows the quick installation, commissioning and expansion of the system as the mine develops. The result is a very robust, flexible system while reducing maintenance costs and spare parts. This paper discusses the impact of sensors, installation and commissioning on advanced controls and provides solutions for in-field applications.

Aug 1, 2013

By Dwayne D. Tannant

This paper presents a new mining concept for oil sands called ?hydraulic underground mining of oil sands? or HUMOS. While this mining method is still at the conceptual stage it has great promise to allow extraction of bitumen from areas that are currently uneconomical or technically infeasible using surface mining or steam assisted gravity drainage. HUMOS is founded on a combination of recently proven technologies such as directional drilling, water jet cutting of oil sands, slurry transportation, cold water extraction of bitumen, and thickened tailings. One key component in the mining concept is the caving of oil sands and the creation of an underground cavern. Scaled-down physical models will be designed and built to demonstrate water jet cutting, cave development, and insitu primary bitumen separation. These will be used as a 'proof of concept'. On-going research will establish and prioritize issues that need to be resolved, outline key areas where further research is needed, foster establishment of research teams to divide and conquer the important questions, and create framework for future coordinated research efforts.

May 1, 2001

By F. H. Samuel, P. Burke, F. Mucciardi, J. Gruzleski, S. A. Musmar

A new thermal analysis technique has been developed and tested. It utilizes the enhancement in heat transfer characteristics associated with a recent advancement in heat pipe technology. Heat is extracted from a liquid sample of a melt taken in-situ within a vessel or furnace. The rate of heat extraction is such as to cause the sample to solidify. The technique was tested in both laboratory scale and industrial scale (Grenville Castings, Perth, Ontario). A 356 Al Alloy, subjected to various melt treatments was used to perform the tests. Classical thermal analysis was also performed simultaneously using a preheated graphite cup and at the same melt conditions. The comparison showed the potential of the new technique over classical thermal analysis. The major advantages of the new method are that it conducts the analysis inside the melt (i.e. a physical sample is not removed from the melt), it consumes less time and the cooling rate can be precisely controlled during the solidification process. Moreover, the resolution of the results is better than that of conventional techniques. Aluminium

Jan 1, 2006

By Benoît Valley

Optimization of the mining sequence in terms of economics (maximizing net present value) often leads to multi-front mining methods generating pillars. Significant resources are tied up in these pillars, but mining them is often challenging. In order to improve our understanding of rock mass behaviour while extracting these pillars, an extensive monitoring program has been designed and implemented at Vale?s Coleman mine (Sudbury, Canada). The program focuses on existing and new technologies that have potential for monitoring deformation and rock mass property changes. It includes both active and passive methods: gravimeters, multi-point borehole extensometers, fiber optic strain meters, fixed and portable three-component seismic arrays, borehole imaging and sonic logging, and, repeated LiDAR surveys. This paper reports results from an initial project phase, when only a small amount of mining has taken place. The goal was to test and compare technologies in order to assess their sensitivity, accuracy, repeatability and suitability for underground mining conditions. Value is gained by having a broad range of monitoring devices running side by side, enabling comparisons and benchmarking.

Jun 1, 2012

By J .. A. Nemes, I. Ragai

This paper discusses one of the common problems associated with sheet metal forming processes, which is spring back. The materials presented here, stainless steel 410 and Inconel 718, are commonly used in aerospace applications for their superior material properties. Standard tensile tests were performed to determine their tensile properties, as well as material anisotropy. In addition, the effect of anisotropy on springback was assessed experimentally through simple multiple-bending experiments in different directions to the rolling direction. Finally, draw-bending experiments were carried out to study the effect of forming conditions, such as blank holding force, on the final springback angles of the formed parts. For both materials, it was found that the R-values measured for different sheets exhibited variation. However, the specimen orientation does not have a large effect on material tensile behavior or springback angle for simple bending. For the Inconel 718 specimens, the springback angle slightly increases with each stage of deformation during multiple bend experiments. The effect of the blank holding force on springback angles was also examined and found to have a significant effect on thin specimens.

Jan 1, 2006

By Gheorghe Vieru

Security and safety due to environmental impact as well as the radiological consequences during the uranium mining operations, tailings management, uranium processing, disposal of waste in conventional landfill sites are matters of great importance. The Uranium National Company (CNU) from Romania is responsible for all aspects belonging to the management of the entire Romanian uranium industry- the uranium ore extraction, transport and processing of uranium ore, concentrates processing, as well as disposal of sterile ore and waste. The paper will presents specific safety problems related to the identification and evaluation of potential environmental risks, as well as possible radiological consequences associated with the disposal of sterile and the uranium processing waste resulting from processing of the uranium ore. Computer codes will be used, such as IAEA INTERTRAN II and RADTRAN 5. It is also to be noted that this paper considers the main results of the scientific research carried out by the main author as CSI (Chief Scientific Investigator) for Romanian Research Contract on NORM concluded with IAEA Vienna.

Aug 1, 2010

By Robert S. G. Chapman, Kieran M. J. Downes

The Sulphide-Preview Lakes area is located 45 km northeast of La Ronge in northern Saskatchewan. It lies within the southern portion of the Proterozoic La Ronge Volcanic-Sedimentary Belt. Two styles of gold mineralization are present in the Sulphide Lake area , stratabound gold mineralization is intimately associated with a pyrite-pyrrhotite-arsenopyrite-bearing graphitic argillite unit within a sequence of intermediate to felsic volcaniclastics. Past operators established three mineralized zones along this horizon with combined reserves for two of the zones, of about 175,000 tons at 0.22 oz/ton Au. In the Preview Lake area , gold mineralization occurs in variably sheared gabbro/quartz diorite sills within a mixed sedimentary-felsic volcaniclastic sequence. Gold occurs with arsenopyrite, pyrite and minor chalcopyrite associated with quartz veins and stringers. A sulphidebearing graphitic argillite unit occurs in close proximity to the mineralized shears. Past operators delineated seven mineralized shear zones, two of which were drilltested. Average gold grades reported are in the 0.1 to 0.2 oz/ton range with erratic values up to 5.0 oz/ton.

Jan 1, 1986

By Jerry Danni

In order to remain viable today, corporations must view the environment as a strategic issue, and integrate environmental management throughout the organization. Corporate programs that used to be based primarily on regulatory compliance now must emphasize strategic environmental management systems, and must integrate these environmental systems with basic business functions. The mining industry today is global, and must have an organizational structure that can embrace different cultures, physical settings, and regulatory regimes. Sound environmental management practices are not different from good management principles. An effective environmental management system should be a complementary system to an organization?s overall management framework, integrated and aligned with the existing management structure. Integrating environmental management into core business functions is just good business. An effective environmental management system is a critical component of a company?s commitment to environmental, social and economic accountability. This paper presents the elements of the Kinross Gold Corporation strategic environmental management system and discusses the integration of the environmental management system into the core business functions throughout the Company

May 1, 2003

By G. J. Hawkes

"We all know that every man who works for us should have a thorough knowledge and understanding of his responsibilities. But how about ourselves? Du we have a thorough knowledge and understanding of our own responsibilities as Mill Superintendents?I once had an occasion to say to a Manager that I did not know something was my responsibility and he replied with suitable emphasis ""Everything inside those four walls is your responsibility"". That makes the extent of our responsibilities clear but does not give us a check list to keep an eye on as we do our job from day to day.What are our responsibilities? I suggest they are the following:1. Developing and maintaining efficient operating and maintenance crews.2. Milling the required tonnage.3. Recovering the economical maximum amount of gold.4. Keeping costs at the economical minimum.5. Seeing that the figures are reasonably accurate for tonnages, assays, production, losses, and costs.6. Preventing accidents.7. Preventing fires.8. Maintaining the equipment and building and keeping them clean and tidy.9. Enforcing company rules and regulations."

Jan 1, 1965

By Rodney S. Read

This paper outlines a reasoned argument why no large-scale fracturing or faulting will be induced in the host rock by a deep geological repository (DGR) for nuclear fuel waste. Four DGR designs in three possible host rocks, including crystalline and sedimentary rock types, are considered. The reasoned argument draws from results of previously conducted thermal- mechanical analyses and new scoping calculations, along with evidence from experiments conducted in Canada and elsewhere. It is concluded that large-scale fracturing in the far-field is implausible given the expected in situ stress conditions in relation to rock strength. Near-field damage development and fracturing are expected in DGR scenarios in the different rock types, but these near-field effects are not expected to lead to large-scale fracturing that could compromise the integrity of the DGR and surrounding rock mass. Additional analysis and characterization activities are recommended to further validate the reasoned argument. Thermo-poroelastic loading of the rock mass is identified as one possible driving mechanism that should be studied further.

May 1, 2009

By A. E. Gillis

"Some or all of the following benefits can be expected following application of automatic control to a grinding circuit:1. Maintenance of Optimum Mill Load Level2. Improved Uniformity of Grind3. Increased Productivity4. Decreased Power Costs per Unit of Product5, Reduced Ball Wear per Unit of Product6. Reduced Labour Costs per Unit of Product7. Reduced Operator SupervisionTo establish an indication of the benefits that could be expected through automation of the grinding circuit at East Malartic Mines Ltd. it was agreed that the Department of Mines and Milltronics Limited should jointly conduct a survey of the existing grinding circuit and operation.Aside from establishing feasibility, an important purpose of this survey was to determine costs of a suggested control system that East Malartic Mines Ltd. management might be in a position to assess the economics of the proposal and justification of the investment.The survey involved the taking of sound recordings of rod and ball mills during manual operations, locating circuit bottlenecks, establishing time constants and determining the number and location of sensors for good automatic control."

Jan 1, 1966

By Art Hamilton

The Zn-Pb-Cu-Ag ore deposits of the Boundary and N-5 zones near Bathurst, New Brunswick, occur in a polydeforrned volcano-sedimentary sequence that is part of the Ordovician Tetagouche Group. Massive and disseminated sulfides are hosted by an argillaceous to cherty sedimentary sequence that is stratigraphically Wlderlain by a siliceous fragmental unit and is overlain by a feldspar-rich crystal tuff and related tuffaceous rocks. The deposits have a low iron sulfide content relative to that of most stratabound sulfide deposits of the Bathurst-Newcastle mining district. The ore is commonly associated with chlorite- and talc-rich sediments. The N-5 deposit is considered to be the fault-displaced extension of the Boundary deposit. The Boundary deposit is estimated to contain 891 000 t grading 3.31% Pb, 7.96% Zn, 0.32% Cu and 44 g/t Ag; the estimate for the N-5 zone is 330 000 t grading 3.24% Pb, 7.15% Zn, 0.33% Cu, and 37 g/t Ag. The ore is processed at 1000 tpd at the Heath Steele mill.

Jan 1, 1992

By Emmanuel John M. Carranza, Martin Hale

Abstract- An application of logistic regression to mapping of gold potential in the Baguio district of the Philippines is described. Categorical map data such as lithologic units and proximity classes of curvi-linear features, based on spatial association analyses, are quantified systematically and used as independent variables in logistic regression to predict the probability for presence or absence of gold mineralization. Regression experiments to compare between using all independent variables that are associated spatially with the response variable and using only statistically significant independent variables are performed. The results of the regression experiments are similar; however, the use of all independent variables produces slightly optimistic results but better prediction rates for the known gold deposits in the test district. At least 68% of the ‘model’ large-scale gold deposits and at least 76% of the ‘validation’ small-scale gold deposits were predicted correctly. The predicted geologically favorable zones are also similar to delineated geochemically anomalous zones. The technique presented using logistic regression as a data integration tool is effective for geologically constrained technique of mapping mineral potential.

Jan 1, 2001