Search Documents

By P. Lausch, Z. X. He, J. F. Archibald

"Documented underground fill failures have resulted because of the lack of adequate knowledge concerning fill strength and other physical parameters, as well as to a lack of consistent quality of fill materials being used by operators. On the basis of literature review and correspondence with backfill operators at 18 mines throughout the province of Ontario, non-systematic quality control procedures have been shown to exist, both within different levels of single operations and between separate mining operations, which act to provide inferior engineered fill materials and erratic application response in situ.Assessment of existing procedures set by mine operators for determining backfill physical parameters, and recommendation of optimum fill material testing and manufacturing guidelines are presented in this paper.A series of standard fill characterization test procedures are recommended to provide substantial, though not comprehensive, fill behaviour review. The purpose of these recommendations is to propose industry standards for backfill quality review. Data acquired could be utilized for fill design functions and as a means of comparing fill quality parameters between sites in a regular and more systematic fashion than is presently done."

Jan 1, 1993

By W. F. Harkness, D. Hodgkinson

"A non-destructive testing program was established at Crows Nest Resources (C.N.R.), Line Creek mining operation following an in-service fatigue failure of a front wheel spindle on a large haulage truck.This failure identified a definite need for improvements in the ultrasonic techniques used during the mandatory spindle integrity examinations. Initial investigations using common mining industry ultrasonic examination techniques showed that the smallest detectable cracks were 75 mm in length for the spindle types in service at the C.N.R. site. The Initial findings indicated that inadequate inspection technique design was the cause of the poor performance. To improve inspection reliability it was identified that improved ultrasonic techniques were required. Results using designed ultrasonic techniques were encouraging, with the detection of simulated and natural cracks 12 mm long achieved. The cost benefits associated with the extended spindle life, following the removal of these small fatigue cracks, far exceeded those of the expertise and effort necessary to implement and conduct the N.D.T. program.Introduction During 50 years of evolution, non-destructive testing (N.D. T.) has progressed from a laboratory curiosity to a well accepted and invaluable tool used in the assessment of material integrity. Unlike destructive testing, N.D.T. does not deform or render the material useless. Non-destructive tests may involve many applications, from the determination of a corrosion prevention coating thickness to the examination of a raw material for internal and external deformities.Within the mining sector, highly-stressed components will normally have been subjected to some form of non-destructive test during their manufacturing cycle. These tests are used to ensure the component does not contain material flaws whichmay be detrimental to its service performance.While the component may have assured quality when produced, deterioration by fatigue may occur during an aggressive service life. Large dynamically-loaded components such as haulage truck front wheel spindles are , in particular, prone to this service related problem."

Jan 1, 1987

By G. Song

Magnesium has excellent bio-compatibility in terms of its density, strength, elastic modulus and toxicity. However, due to its poor corrosion performance, so far magnesium has not been successfully used in the human body as a permanent implant material. Nevertheless, there is a possibility to utilize the low corrosion resistance of magnesium to make magnesium into a temporary implant component that can gradually dissolve in the human body after surgical region heals. This will avoid the secondary operation to remove the temporarily implanted component and the chronic inflammatory discomfort caused by the implant. This paper is aimed at exploring the possibility of using magnesium as a degradable bio-material through investigating the corrosion behaviors of pure magnesium and surface treated magnesium in a simulated body fluid (SBF) solution. It was found that magnesium corroded rapidly in the SBF solution, resulting in vigorous hydrogen evolution and a strong alkalization effect. Hence, it is impractical to use magnesium as a permanent implanted material or even a degradable implant. However, a proper anodizing treatment can significantly improve the corrosion resistance of magnesium, and hence slower down the hydrogen evolution and alkalization processes, which will allow to control the corrosion or degradation of magnesium at a desired rate in the human body. With a controllable corrosion rate, it is believed that magnesium as a degradable implanted material will be eventually achievable.

Jan 1, 2006

By A. Flemming

"As the next century draws near, new mine properties must be brought into production to replace existing operations that are approaching their economic life. This paper presents some of the critical technical issues being addressed by Manalta Coal Ltd. as they strive to bring the Telkwa Coal Project near Smithers, BC into production during the year 2000. The mine is planned to produce between 1.0 to 1.5 million tonnes per year of medium volatile coal for export to overseas thermal and PCI markets. IntroductionManalta Coal Ltd. (Manalta) is proposing the development and operation of a surface coal mine and associated infrastructure approximately six kilometres southwest of the village of Telkwa, British Columbia (Fig. 1). The infrastructure consists of a coal washing facility, tailings disposal area, clean coal haul road, access road and rail loadout facility. Over a 25-year period, the mine is expected to produce between 25 and 37 million clean tonnes of coal primarily for the export market.To achieve public and governmental approval for the development, the project will be reviewed under British Columbia’s Environmental Assessment Act. Manalta entered the formal Assessment process in February 1, 1997 with the submission of an Application for a Project Approval Certificate for the Telkwa Coal Project."

Jan 1, 1997

By T. H. Peters

The historical development of this program, dating from the construction of Nickel Park at Copper Cliff in 1917 to the various current projects carried out in the Ontario Division's program, is reviewed. Practices used to grow vegetation on stressed areas, the beneficial aspect of the improved aesthetic appearance of company properties from the point of view of public relations and the improved approach to the workplace by the employee are discussed. The revegetation of the tailings area and its gradual transformation into a Wildlife Management Area is reviewed.

Jan 1, 1978

By W. L. Goodwin

Twenty-five years ago mining engineering in Canada was not a profession. To-day the members of the mining fraternity can fairly claim for 10themselves the professional status. If their pretension is not fully warranted by fact it is not for lack of any technical attainment or service to the public but by reason merely of their neglect to cultivate the cohesion and consciousness that are the outward and visible signs of a professional body. This paper is an attempt, first to sketch briefly the course of the events during the past thirty-five years that have resulted in organizing the mining industry of this country in its present form; then to notice the principal features of the professional organization of this day; and finally to point out that an important part of the work of the mining engineer remains in the state of chaos that characterized the whole of it three or four decades ago, and to suggest a remedy. Thirty years ago there came a great wave of interest in mining in Canada, based principally upon the discovery of gold-quartz and gold-copper throughout wide areas in Nova Scotia, Ontario and British Columbia.

Jan 1, 1926

By A. G. Pronk, D. M. Burton

"A regional till sampling program in the Upsalquitch Forks-Tetagouche Lakes area, centred some 70km west of the city of Bathurst, has proven an effective method for gold exploration in the heavily glaciated interior of northern New Brunswick. Prospecting activities within this area over the past three years, have led to the discovery of several gold occurences associated with quartz-carbonate alteration in a variety of intrusive rock types emplaced along major fault zonesQuaternary mapping shows that the glacial history is complex. However, the displacement of material is uniform in distance and direction, and the till is generally thin (0.5 m to 2.0 m) and locally derived, making the interpretation of till geochemical patterns relatively simple for the explorationist. Previous studies have shown the the fin e-grained gold is best detected in the -250 mesh (-0.063 mm) till fraction (clay plus silt) and that the C-horizon is the preferred medium for analyses.Samples were collected on a 2 km grid and analyzed f or Cu, Pb, Zn, Au, Ag, As, Sb, Mn, Fe, Ni, Co, and Cd. Results indicate that concentrations of 10 to 20 ppb Au can effectively delineate areas of anomalous gold in bedrock associated with fault structures, and that a good potential for discoveries exists to the west of the known occurrences, where up to 678 ppb A u has been detected in tills. IntroductionThis paper reports on the result s of surficial geological investigations conducted over the past two field seasons in north-central New Brunswick. The stud y area is located in the Upsalquitch Forks-Tetagouche Lakes map area s (N.T.S. 21 0 19 and 21 0 (10) 70 km west of the city of Bathurst (Fig. I). The area is situated on the margin of the New Brunswick Highlands and has a maximum elevation of 640 m (for a detailed description of the physiography, see Rampton et al. 1984).Historically, exploration in northern New Brunswick has concentrated on base metals within the Cambro-Ordovician Tetagouche Group, resulting in the discovery of man y significant massive sulphide deposits (Brunswick No.6 and No. 12, Heath Steele, Caribou, Armstrong Brook, Orvan Brook, McMaster, Murray Brook, and Restigouche). Auriferous base metal occurrences along the Rocky Brook-Millstream Fault have also been previously investigated."

Jan 1, 1988

By Kenneth M. Haley

THE development of Reserve Mining Company's pelletizing practices began in 1949 in a pilot plant located at Ashland, Kentucky. Three years later the participating companies -Armco Steel Corporation, Cleveland Cliffs Iron Mining Company and Republic Steel Corporation concluded the work and the small plant was shut down. Oglebay Norton and Company was the operating manager and Armco Steel Corporation furnished labor and services. Arthur G. McKee and Company were the designers and constructors. The equipment flow sheet that was employed in that pilot operation is shown in Figure 1. This was Reserve's first step from the laboratory work per-formed by the Mines Experiment Station of the University of Minnesota in developing a commercial operation. The plant used New York state concentrate, purchased from Jones and Laughlin Steel Corporation's Benson Mine. This concentrate, minus 14 mesh, 64.3 per cent Fe, 5.7 per cent Si02, was processed at Ashland to 80 per cent minus 325 mesh in conventional ball mill, classifier, thickener, filtering

Jan 1, 1961

By R. K. Rajamani

Discrete Element Method simulation of charge motion in ball, SAG and autogenous mills has become a standard for design of mill internals, power draft evaluation, etc. Both two-dimensional and three-dimensional codes are being used. The two-dimensional code dominates the user market since the code completes a simulation in one or two hours. On the other hand, three-dimensional codes have been in the domain of specialists who can handle the complexity of the code and have access to parallel computing hardware. For the first time, this barrier is overcome via computing with graphic processing units (GPU). Commodity graphics cards now allow parallel computation with hundreds of processors. It is shown that the computational time has been reduced by a factor of fifty using GPU computing. Hence, SAG charge simulation results in three dimensions are achievable in a few hours using affordable desktop machines. The GPU computing shown here enables the three dimensional simulation into a manageable daily task for mill designers and researchers. On the technical side, the simulations can be elevated to a higher level of complexity to simulate breakage and transport. First, the speedup factor of fifty is established for the Nvidia GeForce GTX 580 graphics card. Next, four simulation tasks, consisting of AG, SAG and ball mills are reported. The simulation of AG and SAG mills are completed in less than 8 hours. The ball mill simulation with 1.25 million spheres is completed in 27 hours. In the near future, as the graphic card hardware advances the compute time can be halved.

Jan 1, 2012

By K. Yamaguchi

"This Precious metals content copper scrap is treated with a copper smelting process, and copper and precious metals are recovered. The precious metal lost in the slag is increasing with increasing of treated scrap amount. To determine the portion of the precious metals chemically dissolved and that associated with the mechanically trapped matte in the slag will be a key factor to improve the recovery of those metals. The distribution of precious metals between copper matte and FeOx-SiO2 slag phases is determined at 1300 oC and a fixed partial pressure of SO2 of 0.1 atm for the matte grades from 40 to 70 mass% of copper. The distribution ratios show a tendency to increase when the grade of matte is increased. In addition, the solubility of platinum and rhodium in the FeOx-SiO2-CaO slag under the air and the solubility of platinum in the FeOx-SiO2 slag equilibrated with a pure platinum or the Pt-Cu alloy were determined at 1300oC in the range of oxygen partial pressure from 10-9 to 10-7. The solubility of platinum and rhodium in the slag tends to increase with increasing content of copper in the slag and oxygen partial pressure. INTRODUCTIONThe stringency of the supply and demand of platinum group metal (PGM) intensifies by localization for resources and increase of the demand for PGM, furthermore, smelting and the recycling of PGM in the nonferrous smelting process take an important role. Scrap containing a precious metal for the purpose of collection of PGM is treated by copper smelting recently. With increase of the treatment amounts, loss of PGM in slags is the serious problem.In considering of PGM loss in slags, knowledge of the distribution behavior for PGM between slag and matte phases or slag and copper phases and the PGM solubility in slags is important. The distribution ratios of silver and gold between the FeOx-SiO2 slag and the Fe-Cu matte were reported by Roghani (Roghani et al., 2000), Shinha (Shinha et al., 1985) and Takeda (Takeda et al., 1993) However, there is no data for the PGM distribution ratio. On the other hand, the PGM solubility in slags was reported by Sano (Sano et al., 1997) However, there is very few report for the solubility of PGM in the nonferrous smelting slags."

Jan 1, 2012

By S. R. Stopic

The EU-financed INTREAT Project (Integrated treatment of industrial wastes to¬wards prevention of regional water resources contamination) addresses the environmental pollution associated with solid and liquid wastes/effluents produced by complex sulphide ore mining and metallurgical activities. The results concerning the electrolytic recovery of cop¬per from effluents formed after mixing of streams from Copper Refining, Precious Metals Plant and Electrolyte Regeneration in the Balkan Area will be shown. The waste water is characterized by low pH values and high contents of heavy metals, such as Cu, Ni, Bi, As, Sb. The majority of these waste water flow untreated into the natural water streams and through the network of existing rivers, which end up in the river Danube. The influence of current density and flow rate on the deposition rate, the quality of copper and the process efficiency will be presented. The full continuous process is based on cells with rotating disc cathodes and represents a pre-treatment step before common neutralisation in a cascade line

Jan 1, 2007

By L. J. Cunningham

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

By C. H. van Eendenburg

"Installation of a 3.6 km long raw coal conveyor in the Balmer open pit was undertaken to improve over-all haulage efficiency. This paper covers the rationale behind this project, system design and construction aspects and initial operating experiences. The majority of the construction work was performed by our own personnel. Where feasible, used equipment was installed to reduce capital cost and facilitate a tight construction schedule.BackgroundWestar Mining Ltd's Balmer Mine is located in the British Columbia Rockies, just outside of the town of Sparwood in the southeastern corner of British Columbia. The open pit mine, which has been in operation since 1969, currently produces about 6 million clean tonnes of coal per year, mostly for the metallurgical coal export market. Run-of-mine coal tonnages total between 9 and 9.5 million annually and waste removal volumes exceed 30 million bank cubic metres.The mine is a truck/shovel operation; loading equipment includes nine electric shovels, five front-end loaders and a hydraulic backhoe. The truck fleet consists of 40 units of 154-tonne, 181-tonne and 315-tonne capacity. The newer 154-tonne trucks are used for coal haulage for which they have been equipped , with tailgates to maximize their coal carrying capacity."

Jan 1, 1990

By P. R. A. Andrews, R. K. Collings

"In cooperation with le Ministère de l'Énergie et des ressources, Québec, le Centre de Recherches minérales, Sainte-Foy, Québec, and various silica producers, selected deposits of Quebec silica were identified in the southern region of the province and sampled to provide material for evaluation as glass and foundry sand by CANMET. The samples included both sandstone and quartz/quartzite. Head sample analyses ranged from 94.66% to 99.54% SiO2, 0.038% to 0.230% Fe2O3, and 0.16% to 4.51% Al2O3.Impurities included pyrite, iron oxides, and iron staining on quartz grains; carbonates as calcite; and alumino-silicates as clay and/or feldspar. Processing included size reduction to grain size, about 600 µm, by jaw, roll and cone crushers, and grinding in a muller-mixer. Removal of fines was achieved by attrition scrubbing and washing. Further removal of impurities was achieved by reverse flotation of iron oxide and alumino-silicate minerals employing both anionic and cationic collectors. Flotation resulted in a substantial improvement in the quality of most sands, the quartz concentrates analyzing 99.08% to 99.80% SiO2, 0.014% to 0.048% Fe2O3, and 0.06% to 0.49% Al2O3. Removal of iron oxide minerals was also investigated using the Sala HGMS. Iron oxide analyses of the non-magnetic fractions were comparable to the iron oxide analyses of the quartz concentrates obtained by flotation, 0.013% to 0.054% Fe2O3. On the basis of the samples submitted, silica from 5 of the 6 deposits studied has potential as source material for glass sand. Foundry tests showed that 3 of the 4 samples submitted for evaluation have potential as foundry sand."

Jan 1, 1987

By T. Güyagüler, U. Y. Önder

"This study investigated the psychrometric properties of ventilating air in GAL coal mines. Related measurements were done in underground openings and have been arranged as input data for computer programs prepared for ventilation network and psychrometric analysis.Results obtained from network analysis have been used for psychrometric analysis of ventilating air. Changes in heat and moisture content of air in two major path s between entry and discharge of ventilating air have been investigated. Psychrometric processes occurring in the mine were determined and are shown graphically in Figures 1 and 2. Special attention has been given to determine the changes in psychrometric properties and processes involved in the faces. Results are outlined in this paper.IntroductionThe psychrometric properties of mine air are important factors to mine productivity and efficiency. Therefore, psychrometric analysis should be made for all underground mines; any undesired situation observe d could be corrected by taking the necessary precautions.The analyses were done as a case study for GAL mines, the only mechanized lignite coal mine in Turkey. In this mine, workable reserve is about 300 million tons of coal and yearly planned production is 2.2 million tons. Production is continuing from a coal measure-bed having two coal seams with average thicknesses of 1.52 m and 1.72 m respectively. A 0.85 m shale band exists between these two seams.Two full y-mechanized faces, approximately 220 m long, usually work simultaneously. All measurements, including mine gases and air velocity, are done by sensors connected to a control room by a monitoring system.In the analysis, a line diagram is utilized to described the mine on which every junction and branch is numbered."

Jan 1, 1992

By L. Mohammadi

Outline ?Background on the accident at the Sullivan Mine No.1 Waste Dump ?Holistic approach to understand the reason for accidents (Atmospheric) ?Specific hazards at reclamation sites ?Regular atmospheric risk assessment at reclamation sites ?Fuzzy risk assessment ?Managing risk at legacy sites

May 1, 2010

By Peter Silveston, Earl Shannon

Process-oriented experiments on the use of coal as an adsorbent for certain soluble components of sewage are described. The capacity of Canadian coals for these components was less than 0.1 per cent by weight for the highest concentration at which these components could be expected to be found in domestic sewage. This is much less than values reported in the past. A pronounced selectivity between components was observed. Experiments on bacteria removal in beds of coal, regeneration of spent coal to restore adsorption capacity and COD contributions of coal are reported in the paper. The simple application of coal as an adsorbent does not seem promising.

Jan 1, 1970

By D. E. Salman, R. R. Maclachlan, R. J. Barclay

"There is a considerable resource of data for spherical charge cratering, both as single charges and in row-of-charge geometr(1). The data are. however, based on cratering performance to a single free planar surface.In practice. the more common circumstance involves an angular surf ace geometry. such as occurs at the toe of a bench or the wall of a stope. It is for the purpose of investigating this circumstance that the described test work was conducted.The test objectives were: (1) to observe the change in single-charge cratering performance between planesurface and angle geometry; (2) to identify the optimum performance of single charges cratering to a plane surface. cratering from a bench sub-grade position and cratering from a condition of zero sub-grade or stope wall geometry; and (3) to observe the performance of row-of-charges cratering to an angular surface at various row burials and spacing. The row charge burial and spacing dimensions were to be expressed in simple numerical multiples of single-charge depth-of-burial data."

Jan 1, 1981

By T. H. Janes

"IntroductionSULPHUR is a constituent of many industrial products. It is part •of almost anything we eat, wear, or use. In fact, sulphur is so important that there has been an increasing tendency in recent years to measure industrial growth in terms of sulphur consumption.The uncertainty of obtaining adequate supplies •of elemental sulphur from the Frasch-mined domes. of Texas and Louisiana in the United States led all countries in 1950 to seek alternative sources of supply of this necessary element.Canadian industry has been supplied, for many years, with most of its sulphur requirements by United States Frasch-mined sulphur. World demand for this sulphur has necessitated the imposition of controls on its distribution, as production has not kept pace with demand. Until the third quarter of 1950, Canadian manufacturers of pulp and paper, heavy chemicals, explosives, and textiles •experienced little difficulty in obtaining their needs of elemental sulphur from the United States. However, at that time, low producers' stocks and declining reserves threatened to reduce shipments from producers, with the prospect of a continuing shortage for some time. These conditions, together with higher prices, stimulated the search for alternative sources of supply in Canada."

Jan 1, 1952

By Ken Wood, Luc Duval

"The development and operation of the milling circuits treating the different Selbaie orebodies are discussed in this paper. The project is reviewed from metallurgical evaluation through construction to present operating status. The current flowsheets are described, with discussion of some unusual features.IntroductionThe Selbaie concentrator commenced initial production in August 1981, treating underground B zone copper ore in a single 1500 t/d circuit. Throughput was increased to 1650 t/d in 1985. The mill was expanded in 1986 to treat ore from the A-I zone open pit; an independent circuit was added to selectively treat 5000 t/d of copper-zinc ore. Current total mill throughput through both circuits averages 7200 t/d with the production of approximately 270 t/d of copper concentrate and 230 t/d of zinc concentrate.This paper describes the stages involved in bringing the project from initial laboratory testing to its current status as one of the most important producers of silver, copper and zinc in Quebec and a major employer in the region."

Jan 1, 1990