Search Documents

By G. F. Trainor

The complex ore body at CNRL?s Horizon mine presents some unique challenges in managing ore and waste delivery. With 25m x 25m ore blocks shovels often take bucket loads from multiple blocks to fill one truck load. With CNRL monitoring 22 different qualities per material a precise calculation of the blended quality of ore on the back of each individual truck is essential to meet the daily blend requirements at the plant. Additionally, one of these qualities must be closely monitored and controlled at a singular level as delivery of certain grade and quantities can cause serious disruptions at the plant. The waste material also requires special handling and delivery for its use in dyke construction for tailings impoundment. Shale materials used in the construction contain high levels of saline that must be contained to prevent seepage into ground water. This paper will discuss how the use of Wenco?s survey-grade GNSS system on shovels, its dispatching algorithm, and fleet management applications give CNRL the ability and confidence to control and report on these three issues.

May 1, 2013

By L. A. Wrigglesworth, A. S. Dadson

The orebodies of the Giant Yellow-knife mine occur in zones of schist, in an assemblage of typical Precambrian greenstones which form part of the Yellowknife Greenstone Belt. One of the most interesting problems at the mine concerns the fold-like attitudes assumed by the schist zones. The internal structure of the zones and orebodies provides much evidence of folding. A logical conclusion would be that the zones represent a single horizon which has been folded and drag-folded in the ordinary course of mountain building. However, surface mapping, and correlation of certain marker horizons, in underground work, indicate a homo-clinal succession of steeply dipping flows. If this concept of the geology is correct, the zones must cross-cut the regional strike at a small angle and, in the over-all aspect, the regional dip at a large angle. A mechanical interpretation of the zone structure is presented as a suggestion for the present until new evidence is found.

Jan 1, 1959

By K. Hardy

As part of Inco's $115 million Fluid Bed Roaster SO2 Abatement Project, a new weak acid treatment plant (WATP) was constructed to treat bleed solutions from the Copper Cliff Smelting Complex gas-cleaning circuits. The WATP produces an iron-arsenic co-precipitate, termed "basic ferric arsenate" (BFA), which requires disposal in an environmentally acceptable manner. Following analysis of many potential options, the short-listed disposal alternatives were: A) Co-disposal of the BFA?gypsum sludge with rock tailings, a portion of which would be used in mine backfill, with the remainder being sent to the tailings area, and B) Co-disposal of BFA?gypsum sludge with pyrrhotite tailings in the tailings area. Testwork showed that the addition of BFA?gypsum sludge to mine backfill samples increased the uniaxial compressive strength (UCS) of the backfill for most samples, especially those at lower binder content ratios. Extensive analysis was conducted on samples taken from the Copper Cliff tailings area, where BFA?gypsum sludge from Inco's Copper Refining Electrowinning Department has been co-deposited with pyrrhotite tailings since 1990. Pore water samples from these areas contained very low arsenic concentrations, indicating that the arsenic had remained stable in that environment. Ultimately, co-deposition with pyrrhotite tailings was chosen as the preferred option for the disposal of BFA?gypsum sludge from Inco's new WATP.

Jan 1, 2006

By D. H. C. Wilton, W. A. Sears

"Abstract-The 682.8 ± 1.6 Ma Tickle Point Group consists mainly of rhyolite flows and tuffs with- in the Avalon Zone of the Appalachian Orogen in Newfoundland. Stratabound massive sulfide mineralization, consisting of pyrite, sphalerite, chalcopyrite and galena, occurs at the Winter Hill prospect, where a lower pyritic, Cu-rich zone and an upper Zn-Pb-rich zone are hosted by a carbonate-calc-silicate lens. At the Frenchman Head prospect, stringers of pyrite, minor sphalerite, chalcopyrite and rare galena are hosted by felsic volcanic rocks of the Tickle Point Group .Base metal ratios, metal zonations and the overall stratigraphic framework suggest that these sulfide occurrences represent volcanogenic massive to semi-massive sulfide mineralization (stringer type at Frenchman Head). As such these prospects represent the only known VMS occurrences within the Avalon Zone of Newfoundland. Pb isotope data indicate that galena from the Winter Hill prospect is less radiogenic and older than galena from Dunnage Zone occurrences, and suggest that the Winter Hill mineralization formed in an environment tectonically distinct (exotic) from the Dunnage Zone."

Jan 1, 1996

By P. Talonen

Since the last Iron Control in Hydrometallurgy Symposium in Montreal in 1996, the Kokkola zinc plant has increased its capacity from 175,000 t/y to 280,000 t/y by installing an atmospheric concentrate leaching process, which has also affected iron control in the leaching circuit. Major changes have been made at the jarosite residue pond; a subterranean plastic wall reinforced with bentonite and cement has been built around the pond. A new water collecting system that is used for groundwater level control in the pond area was installed. With these two investments in the pond area, it is now possible to prevent any seepage flow from the pond into the surrounding environment. Water pumped from the residue pond is treated in the water treatment plant. This paper describes the behavior of iron in Kokkola's current leaching processes. The treatment of the jarosite, the improvements to the residue pond and the water treatment process are also described.

Jan 1, 2006

By Bertrand Quiniou, Pierre Amadieu

Ion exchange technologies and processes are proven and established technologies widely used in numerous industries including hydrometallurgy for metal separation and recovery from metal bearing solutions. They have evolved through innovation which includes the development of countercurrent multistage (or multivessel) ion-exchange contactor systems with the benefit, for industrial operations, of greatly reduced footprints and ion-exchange media inventories, as compared to more traditional fixed bed contactor systems. Information on procedures for design and sizing of countercurrent multistage ion-exchange contactor systems is not readily available since it is most often proprietary know-how. The purpose of the present work is to develop a simple and innovative approach for the sizing and modeling of industrial countercurrent multistage ion-exchange contactor systems. The suggested approach builds upon published results and upon the following observation: in an industrial setting, knowledge of how component concentration or load on a contactor output streams vary with time t within a cycle duration (0 < t < T) is generally of little interest, only knowledge of time average of such concentration or load over a cycle duration T is sought for. The presented approach will be tested against current or past performances of industrial countercurrent multistage contactors of Orano Mining operations such as SNK‑3M moving packed bed contactors in Kazakhstan and NIMCIX fluidized bed contactors in Namibia.

Jan 1, 2020

By Zhiyang Long, Ruiling Xiao

"A mine shaft is one main development method of establishing access in an underground mine. The construction technology of the mine shaft sinking is complicated and large equipment setup on surface and in the mine shaft. The paper briefly reviews a single-line operation method, parallel operation method and mixed operation method as well as the features of the one operation method with the excavation, lining and installation. The special construction technology mainly would include ground freezing methods, full diameter shaft drilling methods, caisson methods, grouting technology and concrete curtain methods as well as other methods. The paper summarizes the shaft sinking numbers and effects by the special construction methods during different periods. The paper states the shaft sinking conditions and the each created record conditions in the coal, metallurgy, non-ferrous metal, hydropower, highway, railway, nonmetallic and other industries. The paper has a prediction on the shaft sinking requirements and development tendency in the future for China.INTRODUCTIONA mine shaft is one main development method of access in an underground mine. In recent years in China the new shaft mines represent 45% of the total number of new mines. With the development of new mining area under construction and the development of deeper mines, the ratio of the mine shaft as access for underground mines will increase. The construction technology of the mine shaft engineering will be complicated, the operation site footprint will be small and the working environment will be more difficult. The mine shaft sinking operation will often be varied by the geological conditions and affected by underground water inflows, seam gas outbursts, geothermal and other natural conditions. The safe construction of the mine shaft sinking will be challenged by all these conditions. Although the mine shaft engineering will only be about 5% of the total mine roadway engineering, the mine shaft construction period often will take over 40% of the total mine construction period. With the progress of modernized mine production technology and the construction of a high production and high efficient mine, the mine transportation roadways mostly would be set in the seam and the engineered amount of the mine rock roadways reduced year by year could cause more prominent long extensions of the mine shaft construction period. Therefore, in order to speed up the construction, to shorten the mine construction period and to realize the investment benefits as early as possible, the technical level of the mine shaft sinking should firstly be improved and the construction speed of the mine shaft engineering and sinking should be speeded up, which would have important significant benefits."

Jan 1, 2019

By P. Srinivasan

Corrosion is a major operational problem in amine-treating plants causing significant expenditures each year, Corrosion may become more severe when the amine plants contain process contaminants ? namely heat-stable salts. The heat-stable salts enter the plants with feed-gas streams and makeup-solution, and/or are produced within the plants by reactions of alkanolamine and available carboxylic-acid anions, This work investigated interaction corrosion effects that may exist in amine-treating plants containing a mixture of heat-stable salts, The investigation was experimentally carried out in a 5 kmol/m3 monoethanolamine (MEA) solution containing 0,20 mol/mol carbon dioxide (CO2) loading at 80°C under atmospheric pressure using carbon steel 1018, Six heat-stable salts, including formate, oxalate, bicine, acetate, thiosulfate and chloride, were tested with a series of salt combinations, Potentiodynamic Polarization, Tafel Extrapolation, and Cyclic Polarization were used for revealing corrosion behavior, determining corrosion rate, and examining the pitting tendency, respectively, Results show that thiosulfate induces the most corrosive environment when present either individually or in the form of salt mixtures.

Jan 1, 2005

By A. Ehsani

"Seas and oceans constitute about 70% of the earth’s surface. They contain an enormous stock of various mineral resources such as sedimentary (marine placers), massive sulfide ore deposits, manganese nodules and cobalt-rich ferromanganese crusts. Sea and ocean floor ore deposits could well contribute to the meeting of ever-rising demand for raw materials in the metal industry. In this regard, more research and development in science and technology appear to be required to ensure maximum benefit from the mineral resources of seas and oceans. Since the 1960s, a variety of mineral and metallurgical processes have been studied and developed to deal with marine ores and to extract metals such as gold, nickel, copper, cobalt, manganese, tin, platinum group metals (PGM), zirconium, thorium, etc.In marine environments, there are many parameters which can affect the selection of the mineral and metallurgical processes. These include the extent and grade of the deposit, mineralogical and chemical properties of the deposit, and physical properties of minerals present with particular reference to particle size distribution and mineral liberation size.In this paper, we briefly review the latest trends in processing and extraction of marine mineral resources. Mineral processing technology is mostly applied for recovery of precious metals i.e. gold and PGM, in particular, from marine placers. In general, pre-treatment (sizing, classification, dewatering), gravity concentration techniques (shaking tables, spirals, jigs, etc.,), flotation, magnetic, and electrostatic separation are the options for enrichment of marine placer ore deposits. In the case of massive sulfides, manganese nodules/cobalt-rich crusts, hydrometallurgical and pyrometallurgical methods (as proven technological methods) can be exploited for extraction of metals from concentrates after physical separation or directly from marine ores. The hydrometallurgical treatments involve acid (e.g., sulfurichydrochloric) and alkaline (e.g., ammonia) leaching with different reducing agents and pre-treatments such as roasting. Alternatively, pyrometallurgical treatments involve mostly smelting, chlorination and segregation processes."

Jan 1, 2016

By M. Bender, H. D. Goodfellow

"Belt conveyors, because of their low capital and operating costs and inherent flexibility in handling a wide variety of products, have numerous applications in the mining industry. With the increased emphasis on improving the workplace environment, dust emissions from belt conveyors at transfer and other points have become a significant problem for many applications.The paper reviews belt conveyor dust control technology and compares dust emissions from belt conveyor systems with other possible materials handling systems. Technical information on existing belt conveyor installations which have been designed to minimize or eliminate dust emissions is summarized. The important features of good design as well as the necessary input from operating and maintenance personnel are highlighted. The status of research and development work on dust control on belt conveyor systems on a world-wide basis is discussed. A proposed methodology for field measurements of emission factors from belt conveyor systems is presented. Data collected from such a test program can be used to establish a design basis for new dust-free belt conveyors.IntroductionBelt conveyors have proven themselves over the year s in the mining industry as a reliable and low-co st method of moving bulk material at high tonnage rates. Because of the above, as well as their inherent flexibility in handling a wide variety of products, belt conveyors are often called the ""workhorses"" of bulk material handling systems. For many processing plants, belt conveyors serve as the ""vital link"" in providing feed to the plant and the removal of the finished product. As would be expected, there has been considerable engineering effort in designing rugged and reliable belt conveyor systems.It is also well known that belt conveyor systems are a primary source of respirable dust emissions. The major sources are from the tail pulley where material is received and the head pulley where material is discharged, from the return idlers, due to the fine material attached to the return belt, and from the take-up pulley. It is usually considered that for dust particles less than 10 microns, these particles will remain airborne and thus can have a profound effect on the workplace environment."

Jan 1, 1982

By Gregory C. More O'Ferrall

Generally pillars in the Southern African hard rock tabular underground mining environment are designed using either empirical pillar design formulae or numerical modelling (analytical) methods utilizing the Hoek-Brown failure criterion. However, none of the pillar design methodologies employed takes cognizance of weak layers either within the pillar material or in the immediate foundation of the pillar. Over the past few years, the presence of a weak layer either within the pillar material or within the immediate foundation of the pillar has resulted in the closure of one platinum mine (Everest Mine), closure of one chrome mine (Wonderkop Chrome) and large-scale instability in a couple of chrome and platinum mines in South Africa and Zimbabwe. A study has been initiated to better understand the failure mode and strengths of the pillars where pillar failure associated with weak layers occurred. Owing to the infancy of the study into the failed pillar strength and failure mechanism, the purpose of this paper is to highlight the circumstances that led to the collapse of mining sections and a shaft, and the difficulty associated with designing pillars in the Southern African chrome and platinum mining operations.

Jun 1, 2012

By Horatio Sam-Aggrey, Margot Hurlbert

Small Modular Reactors (SMRs) have been touted as having the potential to spearhead a nuclear renaissance. Proponents of this view cite the relative advantages of SMRs over larger nuclear plants as reason for their optimism. Some of these merits include potential economies of mass production deriving from modular factory production, enhanced safety features, the ability to locate reactors in remote areas, and reduced requirements for technical workforces to install and maintain SMRs. Despite the optimism surrounding SMRs, nuclear power is still a contentious issue for many Canadians. The growth of nuclear power remains adversely affected by concerns over issues such as: the health and safety consequences of nuclear power generation, environmental impacts, proliferation of nuclear materials, terrorism, and radioactive waste disposal (Organisation for Economic Co-operation and Development (OECD) and Nuclear Energy Agency (NEA), 2010). Personal values, past nuclear accidents, and lack of trust in the industry are other factors influencing attitudes toward nuclear energy (IAEA, 2005). In Canada, three main areas where SMRs could be used have been identified. These include: a. Traditional, on-grid power generation, especially in provinces looking for zero-emissions replacements for CO2-emitting coal plants. B. Remote off grid communities that currently rely on diesel or fuel oil power generation. There are 279 off-grid communities in Canada, many of them being Aboriginal communities (NRCan, ND). Notably, all communities in each of Canada’s three territories qualify as remote. C. Resource extraction sites, such as mining and oil and gas extraction sites. Many of Canada’s principal producing mines and active mineral exploration projects are located within close proximity of Aboriginal communities. Any proposed implementation of small nuclear plants would, require the support of the local population, which is largely Indigenous in the northern regions. The possible deployment of SMRs raises important issue relating to consultation and accommodation of Aboriginal concerns regarding potential SMR deployment. This is especially pertinent given Canada’s pending implementation of the provisions of UNDRIP. One of the provisions of UNDRIP that has attracted a lot of attention is the one on Free Prior and Informed Consent (FPIC). Drawing on previously published information, this paper discusses some of the challenges posed by FPIC for the deployment of SMRs. The next section outlines the provisions of FPIC and its implementation in the Canadian context. Section 3, details some of the challenges posed by FPIC to the deployment of SMRs, while Section 4 provides some concluding comments.

Jan 1, 2020

By Dr. O. M Solandt

CANADA is not an old country we are just now planning to celebrate our lOOth Anniversary. Nonetheless, we have already developed some well-established traditions. One of the minor traditions is the standard speech on the need for more research and development in Canadian industry. I am sure that you have all listened to it many times -I certainly have given it more than once. Much as I am tempted to honour this tradition by repetition, I shall only give you a thumbnail sketch of the ancient address for the benefit of any unfortunate visitors who have not heard it before, and also to provide a base for some further ideas that I want to leave with you. Briefly, the traditional story is that, for a variety of historical and environmental reasons that I shall not attempt to describe in detail, research and development in Canada has grown up in a pattern that is ill adapted to foster the expansion of our manufacturing industries. The story continues by saying that research in the universities is of excellent quality but that we are very short of money to meet the expanding needs

Jan 1, 1965

By J. S. Laskowski

Anisotropic minerals are important constituents of many ores. This group includes both valuable minerals (e.g., molybdenite in Cu-Mo ores) as well as gangue minerals (e.g., talc in platinumbearing sulphide ores in South Africa, graphite in Cu-Ni sulphide ores in Canada, chrysotile in Ni sulphide ores in Australia, and clay minerals in all types of ores). Aqueous suspensions of anisotropic minerals exhibit different properties than suspensions of isotropic minerals. The presence of anisotropic minerals in flotation circuits affects the flotation process.

Jan 1, 2012

By N. L. Richards

In manufacturing for the 21st century, the first company to market often leads the pack in product development and sales. In this respect, manufacturing processes play an important role in transforming “raw materials” into a product(s) for sale to a customer. Thus it can be seen that upfront modelling of a design concept, or modelling of manufacturing processes in a plant, can play an important role in effectively ensuring the overall design and manufacturing route is carried out in an expeditious manner. In the paper various scenarios are considered with respect to modelling the microstructure and/or process, in various manufacturing processes. Also considered are the effects of service condition on the manufactured product in terms of creep and fatigue.

Jan 1, 2010

By G. A. Moruzi

Two sulphide dust secondacy explosions have occurred in the mines of the SUdbury operations of Falconbridge Ltd. during the past 18 months. 'Ihe main similarity between the occurrences is that they both happened in vertical crater retreat blasthole stopes. A relatively high p:,v.tier factor was noted in both instances. other details are enumerated and examined, as well as some results of tests done by Noranda Research on company ore samples.

May 11, 1988

By R. Fukuzawa

"The objective of this research is to evaluate the magnitude of carbon prices required to drive process development and innovation for the global nickel industry in a direction that tackles the multifaceted sustainability challenges that the industry faces, including air pollution reduction and greenhouse gas abatement. The results suggest that the currently considered carbon prices are not sufficient to drive innovations in processing methods or upstream pollution prevention. The co-benefits of climate change mitigation and pollution prevention cannot be readily realized under climate change policy alone. Increased coordination between climate change policy and performance-based environmental legislation is necessary. INTRODUCTIONNickel is an important metal in our modern society as it is used in stainless steel, alloys, electroplating and rechargeable batteries, all of which are integral to our economic growth and development (Eckelman, 2010).However, nickel production is energy intensive and therefore susceptible to emerging climate change policies, which may lead to production curtailment and/or increased unit costs of production unless changes in efficiency or energy sources are made (Mudd, 2010). The industry is faced with multi-faceted constraints: future technology must not only deal with metallurgical, financial and environmental constraints but also promote low energy and low carbon practices. This presents a challenge for this industry where technology innovation, development and commercialization are often lengthy, risky and costly processes (Imrie, 2006).Climate change is one of the many challenges faced by our society. Others include other pollution to air, water and land, resources shortage and economic development. From a policy perspective, it is important to balance multiple and often competing needs in an integrated manner. It would require some levels of trade-off in order to maximize the overall effectiveness but also to ensure that one policy does not undermine other policy objectives.The aims of this study are to evaluate how developments in climate change policy would affect the nickel industry in the context of existing environmental regulations and how the industry could respond under these constraints."

Jan 1, 2012

By J. Desroches, J. Burghardt, N. Whitney, B. Lecampion, A. Surdi, M. Houston, S. Stanchits

There is accepted evidence that multistage fracturing of horizontal wells in shale reservoirs results in significant production variation from perforation cluster to perforation cluster. In fact, only a fraction of the perforation clusters seem to contribute to production in many shale gas and shale oil plays. In many cases, the orientation of the lateral section of these wells is determined by lease boundaries rather than principal stress directions, and these often do not coincide. When horizontal wells are misaligned from the far-field principal stress directions, the fracture must reorient from the near-wellbore principal stress directions, which are aligned with the wellbore, to the far-field principal stress directions. The primary objective of this study is to learn how various completion designs influence the near-wellbore fracture geometry when such a misalignment exists. A secondary objective is to understand the influence of rock fabric features, such as mineralized natural fractures, on this reorientation process. To understand these effects, eight laboratory hydraulic fracturing tests were conducted using a true triaxial vessel with 914 mm × 762 mm × 762 mm samples of Niobrara shale. Several different completion designs were studied, including the use of fracture initiation slots with several different orientations and the use of perforations selectively located to encourage a smooth transition from the near- to far-wellbore region. The tests were carefully scaled as accurately as possible to provide insight into the field near-wellbore phenomena. Pressure and fluid flux at the wellbore, deformation of the block, acoustic velocity, and induced acoustic emissions were acquired during the tests. Additionally, sized particles were also injected to gauge the fracture width away from the wellbore. After the test, the blocks were dismantled, and the fracture geometry was mapped in 3D. These measurements allow one to clearly differentiate the fracture initiation and the breakdown—meaning the peak pressure—to be clearly differentiated; the fracture was already well developed when the maximum pressure was reached. The study reveals non-negligible tortuosity and aperture restriction in the near-wellbore region. In the field, this would translate to high treating pressures, uneven proppant distribution, and possibly near-wellbore screenouts. The test results show that, of the configurations tested, the best approach is to use deep slots that are aligned with the far-field principal stress directions. The oriented perforation design did not achieve the simple, smooth transition that was hoped for, and instead produced multiple competing near-wellbore fractures and considerable tortuosity. The study also demonstrated that the presence of planes of weakness, such as mineralized natural fractures, near the slot tip can result in poor near-wellbore fracture geometries, even for the best completion configuration. We conclude from these tests that the misalignment of the well with a principal stress direction creates near-wellbore complexity that, in turn, creates uncertainty in proppant distribution and, therefore, production; proppant might avoid up to a half of the created fracture. Regardless of the wellbore orientation, this uncertainty is further increased by the presence of mineralized features in the rock fabric that can strongly alter or stop the growth of the hydraulic fracture. Preventing those effects by changing the completion alone proves difficult, and new strategies are required to ensure a reliable stimulation of shales.

Jan 1, 2015

By Ben D. Thompson

Cemented Paste Backfill has proven to be of critical importance to the operation of a number of Canadian mines, primarily due to the rapid backfilling rate this method permits. In order to improve the efficiency of this backfill system (i.e. optimize binder contents, fill fence design, and the employment of two stage filling strategies) there is a requirement to better understand its geomechanical behaviour. In response, in-situ experiments have been conducted in long-hole stopes to quantify the evolution of total earth pressures and pore pressures at a series of instrumented points within both the core of the backfill and close to fill fences. The deflection of fill fences as a result of paste loading has been measured and additional instrumentation has also been employed to measure cement hydration, negative pore pressures, and blasting induced vibrations within fresh and cured paste backfill. Installing geotechnical instrumentation within an open long-hole stope can be an extremely complex procedure and this paper details the methods that have been successfully employed. Preliminary results are presented, and the pressures induced by backfill with differing binder contents, at a number of different in-stope locations are considered.

May 1, 2009

By O. Hall

STOPING at Noranda" is a sequel to "Mining at Noranda". "Mining at Noranda", presented in 1937 (1), sketches Noranda&apos;s history, metallurgical problems, exploration, mining methods, mining details, pillar extraction, and costs. "Stoping at Noranda" deals in greater detail with our stoping, the use of sub-level drifts instead of benches, and the drilling out of the stopes with jointed rock drill steel and diamond drills. Sun-LEVEL DRIFT STOPING: Sub-level drift stoping is almost universal throughout the mine and is the standard sroping method in both sulphide ore and rhyolite flux ore. The features that have led to the adoption of this standard are: (1) Continuous symmetrical drilling in sub-level drifts with no delay for blasting. (2) Large-tonnage blasts Saturday night after the drillers have left. (3) Comparative freedom from gas and smoke during the working days. ( 4) The daily safety achieved by having all stope drilling done in drifts. (5) The safety and security achieved by drilling out stopes, floors, and pillars before there is any weighting or cracking.

Jan 1, 1939