Search Documents

Lower Silesia Coal Basin/SW Poland/ is adjacent to highly gas saturated igneous massiv and since the beginning of this century more than 1500 outbursts have occurred in four existing mines, including 1295 in the most hazardous mine Nowa Ruda. Prevailing part of these are carbon dioxide/coal outbursts of ejected masses 50-5000 tonnes/av.200/t and gas volume released from 200 m3 to 800,000 m3 Magnitude of these phenomena is growing with the depth and for present extraction levels/ 375-753 m/ may be expressed by a formula: M = 4.25/H-400/, where M-masses ejected, t and H - depth of extraction, m. Regulations obligatory hitherto call for gas pressure measurements to be made in 3 m long and 42 mm dia. boreholes spaces not more than 25 m along the longwall face and taking sample of drillings for desorption testing. Criteria of a hazard are following: pressure higher than 30 kPa /for C02/ or 80 kPa /for CH4/ and desorption more than 1,44 cm3/g. These criteria are not satisfactory because many outbursts occurred in spite of low values of parameters measured and for several times no hazard was evident after very high values were obtained. Moreover, observations show that a huge majority of case outbursts occurred in coal weakened by local geological distortion.

Jan 1, 1980

After the minim operation, most raw materials that occur in the earth's crust require some form of processing or refining before they can be converted into a final end product. In the mineral industry these remarks apply to materials such as iron ore, bauxite, limestone, copper ore and many others that are found in Australia in large quantities. Processing plants for these raw materials operate more efficiently, however, if the feed to them is consistent in both physical and chemical characteristics. Such uniformity rarely occurs in nature so that some form of homogenisation, or blending, is required ahead of the processing plant. Bending also assists the mining operation itself by reducing; the need for selective mining and, by combining high and low grade materials, a more uniformly graded, commercially acceptable product can be obtained, thereby increasing the commercial life of a mine or quarry. Bed blending is the most efficient of the processes available, and following its development in the United States in 1905, over 100 plants have been installed, or are under construction, all over the world. The original process, the Robins--Nessiter system, has been the subject of continued improvements and refinements, so that economical capacities are possible from less than 100 l.t.p.h. up to 10,000 l.t.p,h. and beyond.

Jan 1, 1969

By G Giles

One of the main tools used by mining operations to mitigate the risk of rock burst is the installation of a so-called ædynamic resistantÆ support system. Such systems are designed to absorb the impact of shockwaves created by mine-induced seismic events. Dynamic support must be strong and capable of sustaining high loads and, at the same time, they have to be flexible and accommodate large deformation. A dynamic support system is therefore a system capable of absorbing a high quantity of energy. Ground support systems are composed of rock reinforcement (rock bolts or cable bolts) and surface support (mesh or shotcrete). In terms of surface support, fibre-reinforced shotcrete is increasingly seen as the industry preferred solution when difficult ground conditions are experienced, including areas of high seismic hazard. A thick layer of shotcrete is certainly strong but it is by no means flexible. Normal weld-mesh has some flexibility, but it is not very strong. The Australian Centre for Geomechanics (ACG), in collaboration with Onesteel Reinforcing Pty Ltd, is currently working on a new high-energy absorption mesh that combines strength and flexibility. The new mesh can be installed with a jumbo, in a similar way as the widely used sheet of weld-mesh. This paper describes the development of this new mesh system.

Jan 1, 2008

By Plyley WF

Kidston Gold Mine is a 3.5 million tonnes per year operation located 280 kilometres west of Townsville, Queensland. Kidston's ore body consists of 44.3 million tonnes graded at 1.79 grams per tonne gold and 2.22 grams per tonne silver. Full production commenced in March, 1985. During the remainder of 1985, Kidston milled 3.77 million tonnes of ore and produced 213,614 ounces of gold.The ore is comprised of granodiorite, polymictic and volcanic breccias. The degree of oxidation of the rock influences the milling capacity and therefore determines the cut-off grade; ore is categorised as oxide, transition and fresh. The milling rates are 15,400, 12,000 and 9,600 tonnes per day for oxide, transition and fresh ore respectively.The ore is treated in a conventional cyanidation/ carbon-in-pulp plant (CIP). The plant consists of a primary crusher, semi-autogenous grinding (SAG) and ball mills, leach circuit and carbon-in-pulp circuit. Carbon stripping and dore smelting are done on site. The major difference between the Kidston plant and other Australian CIP plants is that a cyclone separation and washing circuit rejects half of the dry tonnage as a sand tail prior to CIP treatment. This difference allows the CIP circuit at Ki.dston to be smaller and makes the CIP less sensitive to the grind circuit product size.

Jan 1, 1986

By Wu H. W, Jones S. J

Australia wide, over 40 fly-in/fly-out mining operations and other forms of long distance commuting now exist, with coverage of about 5000 employees. The substantial majority of these operations are in Western Australia, with some mines also located in Queensland and the Northern Territory. In recent years new large-scale mining operations have adopted the fly-in/fly-out approach and it is important to note that no new mining towns have been constructed in Australia since the township of Roxby Downs was built in the late-1980s to service the Olympic Dam mine. An examination of fly-in/fly-out mining operations in Australia has been undertaken. A detailed survey undertaken in 1990 has been reviewed and another intensive survey undertaken to establish emerging trends. Results from both company and individual employees point of view have been analysed. A section examines the views of professional employees and the influence of fly-in/fly-out on career development. Bus-in/bus-out coal mining operations are emerging in Queensland's Bowen Basin. These operations commute their employees into the mine site for compressed working schedules while the mine employees' families are domiciled in regional cities such as Mackay. A review of the issues associated with the development of long distance commute coal mining operations in Queensland's Bowen Basin is performed and two case studies examined.

Jan 1, 1997

THE power requirements of the Mount Lyell Mining and Railway Company at Queenstown, Tasmania, have, since the inception of smelting operations in June, 1,,896, been derived continuously from the extensive forests in the watershed of the Queen River, adjacent to -the works, the firewood being of good quality, mainly composed of myrtle or beech (Fagus Ounninghami), eucalypts, and manuka (Leptospermum ericoides).The country is very rugged and mountainous, indented by numerous ravines and gullies, and intersected by many creeks, which are subject to periodical floods, under the influence of a heavy and persistent rainfall. The areas so far exploited aggregate a total of about 42 sq. 'miles, and this denuded country gives promise of ultimately becoming very valuable pastoral ground for cattle-raising. The tonnage of wood yielded per acre varies from 40 to 100 tons on stack measurement of 80 cub. ft. per ton, 60 tons per acre being considered a good average yield. The gross amount of firewood handled during the past 13 years approximates 1,200,000 tons, the greater portion of which has been obtained by ordinary tramming methods. The company's main line of railway, 3-ft. 6-in. gauge, has served as a trunk line for all supplies derived from the Queen River valley, south of the reduction works, while the northern and western areas have been exploited by means of...

Jan 1, 1911

By Sen G

An amount of explosives, whether it be cylindrical, spherical, etc in configuration, with a hollow cavity in one face or end is known as a hollow or shaped charge. When this charge is initiated, a focussing of explosive energy will occur within this cavity. This focussing, or concentration of detonation products creates an intense localised force greater than just the simple detonation of a conventional explosive, (without a hollow cavity). If this hollow cavity explosive is directed against a target material this concentrated force is capable of creating a deeper penetration than the same amount of explosive without the hollow cavity. If a metallic liner material is used in the hollow cavity, upon detonation of the explosive this liner will form into a high velocity penetrating jet. Depending on the explosive type and the liner material's configuration the jet tip can travel up to 10 km/s. Linear shaped charges were developed using the abovementioned shaped charge concept but instead of being formed about an axis, they are elongated and constructed along the principal axis. Therefore instead of creating a narrow circular penetration jet, it forms a thicker planar cutting jet ideal for linear cutting purposes. Using Linear Shaped Charges (LSC) for pre-splitting is expected to result in more accurate directional fracture propagation, while minimising lateral micro fractures in the surrounding rock mass which is required to remain undamaged.

Jan 1, 1995

Published information on technical and market developments in the uses of zinc tends to dwell very largely on two groups of uses of zinc - zinc coatings (mainly galvanising) and zinc casting alloys. These two groups account for two-thirds of primary zinc consumption. However, if total zinc consumption is taken into consideration, coatings and casting account for a little over half the total. Either way, the health - or otherwise - of these 'other' uses of zinc can have a substantial effect on the industry as a whole. The aim of this paper is to put the whole market picture for zinc into better focus, concentrating on the factors which can affect consumption in the 'other half' of zinc's markets: ò brass - the third most important market for zinc at around one million tonnes - responds to changes in the economic cycle. It has seen substantial changes in the balance between different forms of semi products, and, in Europe at least, some real market gains; ò zinc sheet - one of the original uses of zinc in Europe - has grown substantially in some countries, but remains almost unknown elsewhere; and ò zinc pigments and compounds are so numerous that - barring the substitution of zinc oxide in rubber - major overall changes in the market are unlikely. The paper examines these markets and assesses their potential and implications for zinc markets as a whole.

Jan 1, 1993

By J-P Franzidis

A technique for determining the recovery of attached particles across the froth phase in flotation that relies on measuring the rate at which bubble-particle aggregates enter the froth is used to investigate the selectivity of attached particles across the froth phase. Combining these measurements with those of other techniques for determining the froth recovery of attached particles provides an insight into the different subprocesses of particle rejection in the froth phase. The results of experiments conducted in a 3 m3 Outokumpu tank cell show that the detachment of particles from aggregates in the froth phase occurs largely at the pulp-froth interface. In particular it is shown that the pulp-froth interface selectively detaches particles from aggregates according to their physical attributes.

Jan 1, 2005

By B Banerjee, N Kumar, S Parihar

Rampura Agucha Pb-Zn Mine (RAM) is located about 200 km to the south-west of Jaipur in the state of Rajasthan, India. Open pit mining operations commenced in 1988 and continued to 2018. RAM open pit footprint is the largest in India with length of 2000 m, width 1500 m and depth of 400 m. Development of an underground mine under the operating pit commenced in 2013, through trial mining longhole open stoping with cemented backfill was established as a preferred mining method. Nine years in operations underground mine has reached the production capacity of 4.5 MT, which represent more than 70 per cent of the ore volume mined by the pit. RAM is currently the world second largest underground Pb-Zn mine.

Nov 29, 2022

By K Biegaj

During the author’s 25+ year career in mine management in various parts of the world (mostly in Australia), the author has been privileged to live and work in mining towns (not FIFO) for more than 20 years. And has personally observed other people from the mining industry carrying out work at home in an unsafe manner, eg pushing lawn mowers whilst wearing thongs or performing electrical jobs whilst standing on aluminium ladders, as well as many others. It is common that injuries sustained at home whilst on break are not reported upon arrival back on a mine site. A large number of compensation claims for injuries at work, which in fact had been sustained at home, come at substantial extra costs to mining companies.

May 5, 2022

This work provides a comparison between the most commonly used classification equipment in the treatment of minerals - hydrocyclones and spiral classifiers - considering their applications and costs. Although in use for decades in the mining industry, spiral classifiers have lost a lot of their importance due to the development of cyclones. This trend, however, is now being reversed, and in the last few years there has been an increasing interest in spiral classifiers, in view of their advantages over cyclones, such as: ò possibility of obtaining more thickened solids; ò less by-pass; ò great durability; ò lower operating cost. This work approaches the different aspects related to the installation, operation and costs of maintenance of these machines, giving a critical comparison of the involved costs.

Jan 1, 1993

Industry and Government is littered with computer systems which suffered massive cost overruns in their production and which do not fully meet the expectations and needs of their users. There are many in the computing business who caution that cost overruns of 100% are to be expected and who counsel seriously against accepting an implementation date as being realistic. System development methodologies and "Spectrum" is an example, have been designed to control systems development so the cost and time overruns are prevented. While some success has been claimed, our experience and information from other users indicates that this control is illusory, the first estimates of cost and time are inflated by the control system methodology, and the methodology itself can bury the original system.

Jan 1, 1983

To reduce the corrosion of a stainless steel crystallizer, caused by accumulation of chloride impurity in the liquor during the crystallization of ammonium sulphate, a strongly basic anion exchange resin in the sulphate form may be used to remove the chloride from the liquor. The spent resin may be regenerated with dilute ammonium sulphate.The ions involved are sorbed by the resin in the order Equation 1. The sorption of chloride from the liquor and the regeneration of the resin depend upon the effect of concentration on the formation of the the ion pair NH6SO4. The sulphate ion dominates sorption from dilute solution of ammonium sulphate containing minor amounts of choride; choride ion dominates sorption from concentrated solution.

Jan 1, 1976

Peraluminous metamorphic rocks may form from a variety of protoliths by a range of processes. Stratiform bodies of such rocks are relatively common in the Precambrian, but less commonly, also occur in the Phanerozoic. The protoliths of such stratiform bodies may have been regionally deposited chamosite-rich sediments, with varying amounts of clastic component, or may have resulted from the in-situ depositional or diagenetic alteration of volcaniclastic sediments, ranging in composition from rhyolite to basaltic andesite.Stratiform peraluminous metasediments, especially those of low to medium metamorphic grade, and relatively iron rich, may be genetically associated with, or be the host rocks for, a variety of styles of mineralization, especially for the ores of An, Ag, Cu, Zn and Pb.

Jan 1, 1990

The general theme of the paper is a resume of factors which induce management to explore for oil, gas, coal and uranium in Australia. It is non-technical in the sense that apart from brief references exploration techniques are not covered. The central theme is the interplay of such diverse factors as taxation, mining 'regu- lations, exploration costs, availability of competent personnel, potential markets within and outside Australia, projected prices of sources of energy and their distortion by governmental action including restrictions on international trade for economic or political reasons, the role of the so-called multi- national companies, extreme views by pressure groups on the preservation of the environment, the availability of funds for exploration and the possible returns to the providers of exploration monies.

Jan 1, 1974

By J Szymanski, S Planeta

In pursuit of optimising the cemented rockfill system fragmentation of the aggregate, while travelling through the surface-to-underground aggregate transport raise, was investigated and a æfines estimationÆ equation was determined. When used with the rockfill strength estimation equation, the fines estimation equation enables an accurate estimation of the compressive strength to be derived theoretically. Optimum fill raise orientation was examined and recommendations are given depending on the varying stope dimensions. If the maximum dimension of the stope is less than 30.5 m (100 ft), a single, centrally located fill raise will suffice. However, as the stope dimensions increase, the number and orientation of the fill raises becomes more complicated and each stope must be examined on an individual basis.

Jan 1, 1998

The Court rejected the suggestion that CRAE had actively misled DMR concerning the worth of its tenements. The Court agreed that CRAE remained silent about certain significant information concerning CRAE's own tenement area. It was a significant question as to what duties CRAE'was under, given that it was in joint venture with DMR in respect of one of the tenement areas. Did that joint venture create an obligation on CRAE to disclose everything it knew? The Court said no. The Court said that the fiduciary duties were defined by the terms of the farm-in agreement between DMR and CRAE. When the Court examined the disclosure obligations within the confines of the contract, it held that CRAE had not breached those terms.

Jan 1, 1990

By H R. C Pratt, G W. Stevens

Hydrodynamic and mass transfer performance are presented for a 72.5 mm diameter pulsed disc and doughnut column of the type used by Western Mining Corporation, Olympic Dam Operation, for the extraction of uranium from sulphate media using Alamine 336 as extractant. For the present purpose, 4.0 g/L sulphuric acid was used as solute. The mass transfer data were interpreted in terms of the diffusion model, thus accounting for continuous phase axial dispersion. The results indicated that an efficiency corresponding to approximately one transfer unit over the 1.0 m height of the column was obtained. This efficiency is comparable to that observed by Gottliebsen (1997) for a pulsed perforated plate column using 173 gm/L sulphuric acid.

Jan 1, 2000

The attachment of a spherical particle to a bubble is theoretically investigated under the condition of a mixed sorption coating of a collector. It is shown that the attachment is determined primarily by the hydrodynamic factor involving the displacement of liquid from the gap between a bubble and a particle. The dependence of the attachment on the state of the surface of particle (sorption coating) is due to a change in the boundary conditions on the interface with water both in the case of surfactant chemical sorption and in that of the physical adsorption of oil. It is demonstrated that at large distances the thinning of a interlayer is facilitated by a physically sorbed collector, while near the bubble this is done by a chemically sorbed one.

Jan 1, 1993