Search Documents

By N Strong

Cracow is a high-grade; low-tonnage underground gold mine located approximately 500 km north-west of Brisbane in Central Queensland. It is a steeply dipping, narrow vein, epithermal gold and silver deposit that is accessed via a decline from surface. Cracow is owned by joint venture between Newcrest Mining (70 per cent) and Sedimentary Holdings (30 per cent). The orebodies are 5 m wide on average and the ore is extracted via sublevel open bench stoping. Stopes are extracted to a strike of approximately 25 m before being backfilled with waste. Prior to the introduction of electronics, the mine would remove a small amount of the previous backfill out to create a void, and then begin blasting two to three rings at a time, with the ore being extracted between each blast. This method caused the ore to be blasted onto the waste backfill resulting in dilution of the high-grade ore. It also meant that the extraction of each stope took a number of weeks and numerous blasting events. In the fourth quarter of 2005, the mine struck a geotechnically sensitive stope, where all 20 rings had to be extracted in a single shot or risk possible geotechnical problems that could sterilise the ore. Due to the limitations of NONEL« delay detonators the mine could not fire all the rings in a single shot and needed to use an electronic detonator system to extract the stope. Some unexpected benefits to the mine were increased fragmentation, reduced vibrations, reduced dilution, improved efficiency and improved hanging wall and footwall conditions. After the success of this first electronic shot, the mine has since moved to firing all their stopes with electronic detonators. With electronics the mine has been able to fire much larger blasts, and has in fact moved to firing their blasts in the opposite direction, firing towards the draw point instead of into the waste backfill, thus reducing ore dilution.

Jan 1, 2007

By A Prinsloo, R Tewu

Automatic control of semi-autogenous grinding (SAG) mills has often been considered complex. Recent experiences at Century Zinc (worldÆs second largest open pit zinc mine) refute this. Together with operating knowledge and appropriate control techniques high quality control is achievable. In this application model-based, constraint, and multiple output control were employed. The control was implemented using standard blocks in the plant DCS. The resulting overall control strategy fulfils the operating objectives and controls the mill with minimal operator involvement over 95 per cent of the time. Previous campaigns using expert systems and complex DCS based control have lacked durability. Their fall into disuse is briefly discussed.

Jan 1, 2009

By Met B. E

The increasing pace of modern mining makes constantly greater demands upon the several contributing departments of rock breaking and transport, and rock-drilling, as the spearhead of attack, has received a great deal of attention with respect to both machines and steels. By a series of mechanical improvements, combined with the application of selected heat-treated alloy steels, the rock-drill has now been developed into a machine capable of rapid drilling and long service under severe working conditions. As a factoryproduct made under strict metallurgical control it is as foolproof as, say, the modern automobile, and, like its prototype, it can be kept in efficient operation by a minor amount of attention during use and by periodical adjustments and replacements.The same cannot be said, unfortunately, of the drills with which the machine is supplied; in conventional mine-shop practice these are made of the best tool steel shaped and heat-treated under the poorest of metallurgical conditions.The crudities of steel-shop practice have, in fact, always prevented the full exploitation of the steels available at any time, and even at the present day the general standard of treatment offers a contrast with the quality of the steels which moves the metallurgist to amusement, despondency or outrage, according to his temperament. Nevertheless, the tendency persists to meet the increasing demands of the rock-drill primarily by the use of still better steels, and secondarily by improvement, of the steel-shop practice. Athird type of development is the introduction of factorymade tools in the form of detachable bits and rods. It is proposed in this paper to deal with these three aspects of the recent developments in rock-drilling.*Re-written from a lecturette given during the First Ordinary Meeting, 1936.

Jan 1, 1936

Taking the third meridian as the eastern boundary of proved payable auriferous country, there is a stretch of country, nearly 600 miles in width, in which no appreciable amount of gold has yet been discovered. Many prospectors have attempted to .penetrate or traverse it, but comparatively few have thought it worth while proceeding with the examination.The desolate stretch of waterless desert-the very few and insignificant outcrops through the sand and the almost total absence of feed for horses have, combined, presented such a barrier as to preclude prospecting. The few who have traversed the country are eloquent in denunciation, yet their investigations, necessarily hurried, are not quite satisfactory. The absence of water utterly debars a thorough examination being made. Gold may exist in quantity, yet it would have to be extraordinarily plentiful to render its obtaining profitable. Too fantastic is the idea of its ever being a mining district; shifting sand to traverse, utter absence of wood and water render the notion absurd. Likely looking belts occur, but these in all "cases are small and remote from water. Gold has been obtained from likely look ing quartz reefs, but only by fire assay, and then but a few do to the ton. Without wishing to be pessimistic, I would unhesitatingly declare that east of the third meridian, and between the parallels 25 and 30 degrees in West Australia, there is no gold in payable quantities.

Jan 1, 1901

The mineralogy and textures of a portion oC ore from the 25 level northern orebody, North mine, Broken Hill are described. This ore, in places, contains up to 70 per cent cubanite (CuFe2S3 ) which has crystallized directly with other sulphides and associated gangue minerals.Several breakdown reactions involving the cubanite are also considered.

Jan 1, 1969

Recent developments in diamond drilling practice have been chiefly 'concerned with modifications in drill design and 'operating technique whereby an increase in daily footage rates and reduced footage costs have been achieved without any marked improvements in the recovery of core. This trend is perhaps due to the general acceptance by the mining and drilling engineer alike of the belief that diamond drilling has definite limitations in exploratory work on mineral deposits characterized by irregularities in continuity and grade, such a belief arising from the fact that drilling technique has not yet evolved coring devices to ensure the full recovery of the rock and mineral formations penetrated.Current diamond drilling operations at Moonta and Wallaroo Mines, carried out by the South Australian Department of Mines, have attained remarkable results in completely eliminating core-loss by the use of a special double-tube core barreI.It is considered that assays of borehole samples taken with this special barrel have a reliability comparable, if not superior to that of similarly situated mine samples and, provided they are spaced satisfactorily, can be used as, a basis for calculating tonnage and grade. Formerly, with only partial core-recoveries, positive borehole results on narrow irregular lodes, such as those in the Moonta and Wallaroo Mines, could be accepted mainly as indications of the presence of mineralization, and could have only a limited bearing on estimates of ore reserves.The value of this special double-tube core-barrel lies In the fact that it guarantees good core recovery and, therefore, good samples, and eliminates the need for sludge-sampling, which is prone to give unreliable assay results from several causes, such as gravity concentration in the bottom of the hole and return water losses which cannot be overcome.In view of the increasing demand for minerals and the probability that the search for them will be carried on largely by boring, it is felt that it would be of interest and value to direct the attention of mining engineers to core-recovery results obtained by diamond drilling plants in South Australia and the features of the special core-barrel, designed by the writer, which has made this possible. Also, the writer is desirous of placing on record two other core-recovery devices designed to extract accurate samples in relatively soft or unconsolidated formations. The latter are used with percussion and calyx plants, respectively and their value has been proven on phosphate rock and coal deposits in South Australia.

Jan 1, 1943

Uranium ore at Sleisbeck, N.T., occurs as lenticular bodies associated with zones of bleached carbonized schists lying between walls of closely folded quartzite. The ore consists mainly of uranium micas with Borne pitchblende.INTRODUCTIONThe Sleisbeck uranium prospect is about 70 miles E. of Pine Creek, and 160 miles S.E. of Darwin (Fig. 1). The prospect consists of a well-defined, E.-W. trending line of hills, about I! miles long. The line is composed of 3 major hills called the Eastern, Central and Western hills, with minor interconnecting hills and outcrops (Fig. 2).

Jan 1, 1955

The following paper on the development of processes for the treatment of crude ore, accumulated dumps of tailing and slime at Broken Hill, has been prepared by a committee of the Broken Hill Branch of the Australasian Institute of Mining and Metallurgy, with the object of recording, in chronological order, the developments of the various processes which have led up to the metallurgical practice of the present day.

Jan 1, 1930

By Becerra J. O

HYL developed a direct reduction process (DR) that does not require a reformer; it is called self-reforming process. Typically, direct reduction processes based on natural gas utilise a reformer unit to transform the natural gas into reducing agents (hydrogen and carbon monoxide). The reforming reactions are: CH4+H20-?3H2+CO CH4 + CO2 - 2H2 + 2CO These reforming units require a catalyst agent to promote the kinetics of the reforming reactions. The catalyst for these reactions is typically a metallic element such as nickel in a ceramic matrix; iron is also an excellent catalyst for the reforming reactions.

Jan 1, 1999

The addition of cement to underground backfill at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited, Broken Hill commenced in 1967. A deterioration in metallurgical performance at each concentrator occurred as a result, with increased loss of lead and zinc to residues. Investigations to determine the reasons for this problem and methods to counteract it have been undertaken. This paper outlines the effects of cement on lead-zinc beneficiation at Broken Hill and presents an interim report on attempts to overcome the metallurgical deterioration.

Jan 1, 1971

The Physiographical Features of the Region The Middleback; Range proper, from the Iron Duke in the south to the Iron Prince in the north, extends in a meridional direction for 21 miles, but may well be taken to embrace also the Iron Knob and Iron Monarch prominences so that the total length of the Range is 37 miles.Although no great altitudes are reached, the slopes of the high country are steep and the Range stands out prominently above the peneplaned surface of upper Eyre Peninsula. The Range is built up of sub-parallel ridges at some places, and its continuity is interrupted by transverse breaks or gaps resulting from normal stream erosion and corrosion during earlier periods when precipitation was heavier and streams were more active. Traces of high-level gravels remain on the flanks of Kimba Gap. A former mature stream on the western side of the Range has had its lower reaches blocked by sand and the old stream channel has been converted into an eiongated basin of internal drainage. The sand dunes in this area appear to be practically stationary at present, being fixed by mallee vegetation. Their trend is west-northwest.The relief of the Range is regarded as having been determined primarily by meridional strike faulting and selective silification of some of the beds. Dip faulting on the Iron Duchess leases has produced subsidiary features only.The Rocks of the Region: In order that some of the points made in the discussion of the genesis of the ore bodies may be appreciated it is necessary to consider the stratigraphical succession and the igneous types represented. This classification may be...

Jan 1, 1949

By Ware AR, Doyle BJ, Hoogvliet H

The Ladolam deposit lies within the altered volcanic rocks of the caldera floor, part of which now forms Luise Harbour. It was discovered in 1982 in the course of a reconnaissance drainage sediment sampling programme. This was designed to follow up indications of surface hydrothermal activity noted by Government geologists during an earlier survey of the Tabar-Feni island chain. Diamond drilling began in September 1983 and by the end of 1989 a payable and proved mineable reserve containing 19 million ounces of gold had been established. Rock types and structures are masked at the surface by intense alteration and weathering. An extensive drilling programme has enabled the identification of these features and the relationships between them necessary for an understanding of the factors controlling gold mineralisation. It has also led to the recognition of two distinct phases of alteration. The first phase of porphyry-style potassic alteration was followed by violent caldera formation, producing extensive brecciation and veining. The second alteration phase partly over- printed the first phase and was an epithermal one, evidenced by argillic, advanced argillic and phyllic assemblages. During this event, a large volume of fluids circulated under the favourable structural conditions; these fluids included a sulphur- rich, neutral chloride brine believed to have transported the gold. Boiling and mixing of circulating fluids in the open breccias is thought to have resulted in deposition of the gold. There is evidence that this process is continuing at the present day.

Jan 1, 1991

The use of black and white and colour infrared film in remote sensing of natural resources is reviewed. In heavlly-forested areas such as New Zealand, the main value of the method is in surveying the vegetation cover to detect the existence of plant communities characteristic of specific geological formations. By contrast in arid areas of Australia where the vegetation cover is sparse and where rocks and soils are well exposed, the method can be used in detecting different rock types or other geological differences.

Jan 1, 1972

By A Kamkar-Rouhani

The paper describes a mineral potential mapping of gold and other base metals in Mahneshan area, Iran, using geographical information system (GIS), in which, the method of weights of evidence is used to combine spatial data obtained from different sources to make prediction for mineral potential. This is a quantitative tool for mineral resource mapping that can be used to delineate and predict favorable areas for further exploration by using the characteristics of known and similar mineral deposits. In accord with the descriptive model for gold and other base metal deposits, the spatial distribution of 20 known mineral occurrences was used. In addition, digital evidential maps were used in this study. The maps include maps of lithological units, faults and first derivative of total aeromagnetic data, remotely-sensing data of alteration and also geochemical evidential maps produced on the basis of the results of chemical analyses of samples taken from the stream sediments in the area, and analysed for Cu, Pb, Zn, Sb, As, Ag, Au, Ba and Hg elements. The binary maps were produced and then combined with the model of weights of evidence using 20 known mineral occurrences to obtain a final map of the favourable areas for further exploration of gold and other base metals in the study area. The final map is a predictive GIS model of the mineral deposits in the area. An interesting matter about the final predictive GIS model is that the faults are mainly located in favorable areas which possesses the most probability of mineralisation. Therefore, the faults in these areas have priority for further exploration of gold and others base metals.

Jan 1, 2005

CONTENTS:1. Introduct'iona. Previous Accountsb. Summary of Geologyc. Physiography2. Morgan Groupa. Lithologyb. Structurec. Faulting3. The Mineral Deposita. Descriptioni. Size and Shapeii. Compositioniii. Effects of Oxidationb. Relationship to Structurec. Genesis of Ored. Mount Morgan Orebodye. Sugarloaf Orebody4. Granitea. Mount Morgan Graniteb. Town Granite'c. Moonmera Granite5. Calliungal Beds6. Razorback Beds7. Acknowledgments8. References

Jan 1, 1952

By A H. Clemens, P Lindsay

Acid producing potential static tests have been undertaken on sample lithologies from New Zealand coal mines, to rank the lithogies into acid producing waste rock and stable non-acid producing waste rock. Results indicated that the main acid producing waste rock in the Waikato coal region are the marine Whaingaroa siltstone and the Glen Massey formations and the main alkaline producing lithologies were the Tauranga group volcanic-derived sediments (A & D) and the Mesozoic basement. Coal ash analysis of 28 samples from 28 mines have also been analysed for reactive S percentage and their base potential has been quantified by the chemical index of alteration (CIA). The results provide mine management in the Waikato Coal region with a classification of problematic and stable waste rock types. XRF and CIA values determined from wash drill cuttings would provide a method of determining waste rock volumes and magnitude of palaeo-weathering underground.

Jan 1, 1999

By R B. Stewart

Where pasture production is the intended land use of the areas to be reclaimed, the creation of a suitable growing +medium is a major objective. To achieve this land reclaimers require a sound understanding of the proposed mining plan and a knowledge of the physical, biological and chemical properties of materials intended for resurfacing disturbed areas. Where the original soil is not being replaced in its natural state, research is usually required to determine an alternative growing medium. Results from field research conducted on waste material from the Waihi Gold mine are reported with emphasis on the significance of soil depth in relation to pasture production in this environment.  Problems in extrapolating field research to large scale operations are also considered.   Essentially the requirements for successful pasture production, on surrogate growing medium, are akin to conventional approaches used in New Zealand in the development of unimproved agricultural land. High inputs of fertiliser are initially needed, especially where volcanic soil is used, and careful management of pastures and soils is required to minimise soil erosion and create a sustainable system. In the first three to five years of pasture production, grazing use of the land requires to be dictated by pasture availability and soil conditions and not by animal feed requirements. The use of light stock (young dairy or sheep) is recommended.   Successful land restoration requires a team approach by a range of cooperative specialists including engineers, soil scientists, farm managers, agricultural contractors, landscape architects and environmental officers.

Jan 1, 1991

By N A. Sikwa, L M. van Niekerk, G N. Ndlovu

In June 2012, Lucara Diamond Corporation officially commissioned its Karowe Diamond Mine in Letlhakane, Botswana. The processing plant circuit incorporates variable speed autogeneous milling, a first for African diamond processing - only previously practiced in Russia. The paper discusses the basis for the selection of milling against the more traditional circuits incorporating crushing and scrubbing. It covers early commissioning challenges of operating a mill in an æalien environmentÆ with no immediate reference plant to look up to for bench-marking.The paper describes how these challenges were overcome and learnings quickly incorporated into the mill operating philosophy for maximum diamond liberation and minimum product damage. The plant was commissioned in three months and by August 2012 the production ramp up had reached name-plate capacity. The feed to the mill has varied from highly weathered material to extremely hard kimberlite and the operating philosophy had to be optimised for the full range of ore types. While more work is required to stretch the mill operating envelope coupled with other circuit additions to improve liberation of fine diamonds at minimum capital expenditure, the mill has, to date, performed to its billing.CITATION:van Niekerk, L M, Ndlovu, G N and Sikwa, N A, 2013. Commissioning and operating an autogeneous mill at Karowe Diamond Mine, in Proceedings MetPlant 2013 , pp 215-228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

The Effects of Collector and Grinding Environment on the Flotation Selectivity of Rosh Pinah Pb/Zn Ore

Sep 13, 2010

The Porgera Joint Venture commenced production during September 1990. A small tonnage underground mine extracts high grade gold ore using small scale stopes. Conventional drill and blast methods are used for development and production mining. Ground support is effected with Splitset anchors, grouted rebar bolts and grouted cable bolts. Splitsets and grouted rebar can be installed by mechanised means. Vertical crater retreat, slot and massfire, and modified VCR stoping tech- niques are used at Porgera. Stopes are backfilled with a relatively strong cemented rockf ill. Future stope sequences require recovery of pillars beside and under filled stopes.

Jan 1, 1991