Search Documents

By Barro L

Very large reserves of gas are contained in coal. Because of the low permeability of the coal gas flow rates are very low. Fracturing of the coal can be achieved by use of the nitrogen - foam frac techniques described but the flow rates after fracturing are not sufficient to support economic development. Fracturing of the seams in the Bowen Basin was as predicted but in the Sydney Basin no trace of the fracture could be found when development proceeded past the fractured well. Testing of coal samples has provided some insight into parameters affecting desorption Rates.

Jan 1, 1982

By A M. Suchowerska, J P. Carter, J P. Hambleton

"In order to effectively predict the roof collapse of underground openings using continuum models, it is imperative that a realistic failure criterion is used to represent the rock mass. However, for coal mining operations, there is still uncertainty as to the appropriate failure criterion that should be used for the coal measure strata. This study compares stability numbers and collapse mechanisms for a rectangular underground opening predicted based on three commonly used failure criteria: the standard Mohr-Coulomb, Mohr-Coulomb with a tension cut-off and Hoek-Brown. Three methods of analysis are considered: an analytical upper bound method an upper and lower bound finite element formulation the displacement finite element method.The theoretical results are also compared with field measurements of subsidence above longwall coal mining. For the standard Mohr-Coulomb failure criterion, the friction angle governs the shape of the collapse mechanism, and the so-called critical width (the cavity width above which failures extend to the ground surface) ascertained from field observations in the New South Wales coalfields corresponds to a friction angle of approximately 30°. On the other hand, predictions obtained based on the Hoek-Brown failure criterion consistently overestimate the critical width. The results also show that tensile failure governs the stability of the cavity and shape of the collapse mechanism when a tension cut-off is introduced for the Mohr-Coulomb yield criterion.CITATION:Suchowerska, A M, Hambleton, J P and Carter, J P, 2014. Prediction of roof collapse for rectangular underground openings, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 367–374 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By Grossi M, Baiden G

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and on- site applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no de- watering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

During 2009 the technical services staff at Barrick Gold Corporation's Australian Business Unit conducted a review of their five underground mines that utilise pastefill as the backfill component for these operations. Of the five mines reviewed three use dry tailings and two use wet tailings plants. The primary aim for these reviews was to determine whether pastefill was the right option to be used, and if not, what where the alternatives. The reviews undertaken focus on several areas including, paste plant operation, reticulation and barricade techniques, the geotechnical requirements for pastefill in regards to the current mining methods, the consideration of alternative methods, capital and operating cost histories compared to initial estimates, and a cost benefit analysis of pastefill against other mining methods. The main benefits from the use of pastefill is increasing the extraction of the resource, reducing or eliminating the need to leave pillars. In some mines the use of pastefill is geotechnically driven, to manage high stress environments or mining induced seismicity. A third benefit of using pastefill in some circumstances is that it reduces dilution, however it is considered that this is not a valid argument for most of the mines reviewed. At two mines no alternative to pastefill was determined, whilst differing extraction and filling strategies were potentially identified at the other three mines. The reviews developed cost benefit curves for those sites that had alternative mining methods to assist in determining whether pastefill is the right option to use for any particular stope. At the grades typically mined in each operation, pastefill was the preferred option to use. In all mines, pastefill was determined to be the best option at this time.

Nov 25, 2010

By A E. Annels, G F. Johansen, B W. Cuffley

Nuggety gold-quartz reefs are characterised by localised, high-grades and in many cases coarse free-gold. Geometrical and grade complexities are often observed. The high-grade regions are generally erratic and have a low continuity; though may make the deposit economic. Viable grades are generally contained within discrete oreshoots, which are surrounded by barren/low-grade material. Drilling is an effective measure of geological continuity, however grade distribution can only be reliably obtained from underground development and bulk sampling. In general terms, only an inferred resource is likely to be estimated from surface drill data alone. Underground development, further drilling and probably bulk sampling will be required to delineate inferred and indicated resources. Closely spaced development with bulk sampling is likely to be the best way to determine a probable reserve. The resource evaluation process must driven by a clear geological model that should attempt to understand the controls to reef geometry and grade distribution. Geological interpretation has traditionally been undertaken in two-dimensions, though computer software is now being used to produce three-dimensional models. Grade interpolation has generally been undertaken using classical methods, typically weighted averages, zone of influence weighting and polygonal/sectional blocks. Tonnages can generally be calculated from diamond drill and development information with a reasonable degree of confidence. Grade is much more difficult to define with confidence because of its highly erratic and discontinuous nature. To account for variability it is recommended that a best estimate be reported within a grade range, as this more accurately reflects the uncertainties involved. Reporting should be undertaken within the framework of the JORC code, but should involve special consideration of grade reliability.

Jan 1, 2000

By R Valenta

Most developing projects face a range of technical and non-technical challenges, and examination of development histories can potentially provide insights into improved approaches to project development. The Kestanelik project in the Canakkale region of Western Turkey was acquired by Chesser Resources Ltd in 2008. Turkey is a significant and growing source of gold production, with sector participation by both domestic and international companies. While the broad ranges of challenges faced by developing projects is well known, there are relatively few case studies in which the range of technical, environmental, social and governance challenges are presented in a single contribution. Recent studies of undeveloped complex orebodies have particularly shown the extent to which environment, social and governance (ESG) complexities contribute to project delays and failures. The Kestanelik project faced a full range of technical and ESG complexities, and provides an illustrative example of the associated challenges. CITATION: Valenta, R, 2018. A case study of technical, social and environmental challenges for a gold project development in Western Turkey, in Proceedings Complex Orebodies Conference 2018, pp 73–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By C Preston, T Williams, D Roy

The easiest way to mine valuable orebodies is through the use of explosives and well-planned blasting layouts that produce fragmentation profiles designed specifically for conveyance equipment in underground mines. The design of blasting patterns is specific to not only the explosives being used but also the rock or ore type being fragmented. Many blasting designs are based solely on the experience of those developed for similar orebodies in terms of properties and orientation or individuals that have some blasting experience.The primary technical objective of this paper is to outline a unique methodology for determining underground blasting methodologies (developing specific blasting parameters) commensurate with explosive energies and rock/ore equations of state for a narrow-vein gold property located in Northern Quebec and for underground mines in general.The procedures developed are to define the desired fragmentation specification so that a specific thermodynamic break is generated, taking into account powder factor, energy factor, tonnages, explosive energies and distribution along with blasthole diameter and orebody orientation for a specific set of explosive and dynamic rock/ore properties. Determining dynamic modulus values for the ore using seismic sensors to measure P- and S-wave velocities, the aforementioned parameters will be utilised to set the design constraints to maximise recovery and minimise overbreak and dilution.New underground blasting software (AEGIS) will use thermodynamic break in conjunction with defined fragmentation profiles to create an array of blasting parameters used to design and plan ring layouts. This software will also allow mining planners, prior to drilling and loading a production blast, to appraise future intended blasting patterns to minimise the potential of diluting ore with host rock and the likelihood of damaging mine support structures.CITATION:Roy, D, Williams, T and Preston, C, 2015. Underground stope drill and blast designs optimisation program, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 137–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Smith

The Broken Hill deposit is located in Australia in the far western region of New South Wales. The deposit was found in 1883 and has been mined continuously since its discovery. It is considered the largest lead, zinc, silver deposit that has been discovered in the world and originally contained around 340 Mt of ore at a grade of around 12 per cent lead, ten per cent zinc and 150 g/t silver. The material remaining in the deposit represents only a fraction (perhaps ten per cent) of the original resource. Several of the world’s largest mining companies can trace their origins to the Broken Hill Field. The remaining resources on the CML7 consist of two large lower grade resource lodes that have not been subject to mining, some scattered areas of zinc lode material and the pillars and remnants of the main lead lodes.The deposit occurs in metamorphic rocks of the Broken Hill Group a division of the Willyama Super Group contained within the Curnamona Craton. The Broken Hill Group rocks have undergone multiple phases of deformation. Metamorphism is granulite grade with major shears cutting through the deposit having been retrogressed to mica schists. The deposit lies in an antiform associated with the second phase of deformation.The resultant proposed mine is situated on Consolidated Mining Lease 7 (CML 7) which occupies a strike length of 3.6 km in the central part of the 7.8 km long footprint of the orebody. Underground mining on CML7 ceased in 1975 with surface mining of silver chlorides in the weathered zone continuing until 1991. CBH Resources has been continually working to define and evaluate the remaining resource since 2002. This work has included four surface drilling programs, two underground drilling programs, an exploration decline, enormous amounts of compilation of historical data and detailed three- dimensional (3D) modelling of historical mining and the resource lodes. It is currently planned to commence production at the Rasp Mine in late 2011. The operations will produce from previously unmined lodes and from remnants and pillars.This paper primarily aims to encapsulate the processes involved from information acquisition through to resource estimation and also to highlight some of the challenges encountered and the specific techniques and practices used to overcome them. Many of the experiences at Broken Hill are applicable to all brown field sites.

Aug 22, 2011

By T Baumgartl, C Gonzales, A Soliman, M Edraki

A soil cover isolates potentially acid-forming (PAF) mine wastes from atmospheric interaction and thereby mitigates acid mine drainage. As a cover that comprises either a single layer or a composite barrier, it essentially manages percolating rain water from flowing into these PAF materials and minimises air flow as oxygen has low diffusivity in saturated soils. However, the availability of suitable soils as cover materials is limited, especially in arid and semi-arid regions where weathering rates are low.This paper investigates the potential use of mine wastes as cover materials in a water-shedding soil cover in north-west Queensland. Four cover trial plots were built using mine wastes as cover materials. Each 2.3 m cover trial plot consisted of a 1.5 m soil cover made up of waste rocks and fines, a 0.5 m drainage layer that consisted of 0.1 m waste rock aggregates and a base layer made up of blended mine tailings. The hydrologic properties of cover materials were determined by in situ measurements and laboratory experiments, which, in turn, were used as input in a numerical model that described the cover’s transient soil moisture profile. The successful performance of the cover is reliant on the long-term stable geochemical behaviour of the substrate used as cover material. Therefore, investigations were carried out to determine the geochemical properties of the cover materials constructed from benign waste rock using static and kinetic tests, with the objective to increase the level of certainty of the material’s benign characteristics. Consequently, the long-term performance of this water-shedding cover design is described in terms of the physico-chemical characteristics of its outflows.CITATION:Gonzales, C, Baumgartl, T, Edraki, M and Soliman, A, ?2014. Mine wastes as cover materials in a water-shedding soil cover in north-west Queensland, in Proceedings Life-of-Mine 2014 , pp 261–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By J Hartnett, B Tarrant, A Rayner, D O’Toole, P Davies

Since 2009, the Northern Territory and Australian governments have been working under a national partnership arrangement to inform a rehabilitation plan for the former Rum Jungle uranium mine. Part of the rehabilitation strategy is to backfill a flooded former pit (Pit), which extends down to 100m below the current pit lake surface and was historically partially backfilled with uranium tailings. It is proposed to utilise the remaining pit volume below water level to sub-aqueously store Potentially Acid Forming (PAF-I) waste rock which currently occupies large stockpiles across the site. The rehabilitation design and planning process undertaken to develop a strategy commensurate to project objectives and construction constraints involved the establishment of key constraints derived from the analysis of historic data sources and preliminary design efforts. Tabled strategies were balanced against dependent project tasks and project objectives, especially surrounding minimising disturbance of highly contaminated materials within the Pit. Ideas were developed in conjunction with industry input and review of case histories to develop a remediation solution that is constructible within the project timeframe and constraints.

Jul 1, 2021

By A Turner, P Hills, D Johnson

Underground mining for gold began in Beaconsfield in 1877 and development of the Tasmania Mine saw the sinking of multiple shafts, including the Hart Shaft over the ensuing 35 years. The mine closed in 1914 at a depth of 455 m due to prevailing economics, eventually reopening in 1999. The modern mine closed in 2012 after extending the mine from a historical depth of 455 m to the exhaustion of the modern Ore Reserve at a depth of 1210 m. West Tamar Council took over the lease for the immediate area around the Hart Shaft as an extension of the adjacent museum. The Hart Shaft and above ground structures became a significant drawcard for visitors. Tasmania was affected by sustained wet weather during May, June and July of 2016 which caused severe flooding and significant Statewide damage. This uncharacteristically intense wet weather caused saturation of the ground surrounding the Hart Shaft. Eventual shaft failure was first identified in August 2016. The failure of the shaft occurred at approximately 50 m below surface and resulted in a plug of material completely blocking the shaft. Significant surface subsidence affecting the surface infrastructure ensued. Due to the unstable nature of the surrounding material, it was determined that addressing the failure above the blockage would not provide a permanent solution to prevent the continued flow of material into the shaft. Many options to stabilise the shaft were considered, however it was assessed that a concrete plug in the shaft in competent ground at a depth of 100 m below surface and well below the blockage, would provide the only long-term solution. Man-entry was considered unsafe. The solution to access ultimately entailed filling the entire shaft with granular fill up to 100 m depth to act as formwork for a concrete plug. The rising mains at 400 mm and 250 mm diameter, which remained in place in the shaft, provided the avenue for placing the fill and ultimately, the concrete plug. Once the plug was in place the remainder of the shaft up to the underside of the blockage and over the top of the blockage to the surface was successfully filled with a combination of more granular fill and flowable cement stabilised sand. The Hart Shaft and surrounding above ground infrastructure was successfully stabilised and re-opened to tourist access. CITATION:Johnson, D, Turner, A and Hills, P, 2018. Stabilising and filling the Beaconsfield Hart Shaft, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 42–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By R Klepper

Separation of leach residue suspended solids from pregnant liquor solution is an important step in hydrometallurgy flowsheets. Alternative flowsheet options are counter-current decantation (CCD) thickeners or counter current washing (CCW) horizontal belt vacuum filters. Extensive sedimentation and vacuum filtration simulations have been completed by FLSmidth on leach discharge slurries to indentify equipment capacity and performance. These data were used to compare Capex and Opex for CCD versus CCW alternatives. In addition, Capex and Opex for large horizontal belt vacuum filters with filtration areas greater than 250m2 are compared to current state of the art sizes of 150m2. This paper presents this information and discusses various advantages and disadvantages.

Aug 8, 2011

The history of the down draught Dwight- Lloyd system of iron ore sintering in Australia is developed. Characterisation of the broad process is given for one plant, and regional divergences from the reference practice are noted and briefly analysed. The subject of the development of high basicity sinters is introduced, and regional differences in approach and results are Examined.

Jan 1, 1972

Coal mining ceased at Strongman Mine this year after 70 years of production. Underground mining finished in 2003 and opencast methods began in 1998. During the life of the mine, 8 million tonnes of coal was extracted from two underground mines and 1.2 million tonnes removed through opencast methods. Strongman Mine is within the Grey Coal Fields; various seams have been extracted from the Rewanui Coal Measures. Coal extracted was predominantly of thermal or semi-soft specifications and characterised by low sulphur and low ash.   The area has steep topography, high rainfall (>3000 mm/yr) and is particularly exposed to westerly quarter winds. Strongman 1 and 2 underground mines are located in the steep, narrow valley which leads to the Strongman Opencast at the top of the valley. Subsidence from underground mining combined with spontaneous combustion, has resulted in an underground fire which has had substantial surface effects. Opencast mining in the steep topography resulted in several landslides at the perimeters of the site. These factors, along with water management, topsoil management and erosion control have added to the complexity of rehabilitating the site.   Rehabilitation of the site is well underway, including infrastructure removal, final landform creation and revegetation of the Strongman Opencast footprint (~45 hectares). Some innovative methods of rehabilitation have been trialled. Successful trials such as helicopter-seeding and moss hydro-seeding on highwalls are now routinely used along with traditional revegetation practices. 18 hectares disturbed land has been replanted with 88 000 seedlings, and another 200 000 seedlings are scheduled for planting over the three years. Fire management is an ongoing challenge; however thermal photography shows a steady decrease in hot areas which have been contained by grout curtains.   Mine closure is some time away and will occur after all standards set by Solid Energy and regulatory bodies are achieved.

Jan 1, 2006

By G J. Lyman

The theory of sampling has progressed slowly over the last century. The concepts of correct sampling were known to mining engineers such as D W Brunton in the 19th century. It was recognised early in the 20th century that the Poisson distribution of particles carrying the target analyte was the key to the uncertainties between samples of a given mass. However, no efforts were made until the 1980s to determine the entire sampling distribution as a function of sample mass. The variance of sampling was made clear by Gy and others, but none attempted to determine the entire sample assay density function until J H Venter in South Africa applied the method of characteristic functions to the problem.Venter applied the method to a specific case of very low analyte concentrations in samples of very fine particle size where his assumption of constant sample mass was justified. When his general methodology is applied to the more general problem, it can be shown that the assumption of constant sample mass is no longer justified and leads to some anomalous results for sampling variance. Venter’s method can be expanded to allow for a statistically variable sample mass and to take into account the size distribution of particles that carry no analyte.This paper presents the basis of Venter’s work and shows how the approach can be easily modified to yield results for the variance that are consistent, for example, with the work of Gy. It is also demonstrated that the entire sampling distribution can be determined without undue computational burden when sufficient information on the material heterogeneity has been collected.CITATION:Lyman, G J, 2014. Determination of the complete sampling distribution for a particulate material, in Proceedings Sampling 2014 , pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By R Grobler, D Burger, L Alberts

The current climate in the mining industry is allowing mining companies to further broaden their views and investigate technologies to improve the safety, efficiency and cost-effectiveness of their operations. Furthermore, underground mine environments will become more demanding for mining equipment and personnel as orebodies become deeper in weaker ground conditions with more extreme environmental conditions. Loading and hauling can represent significant components of the production cycle of an underground mine and automation of these activities can offer considerable benefits. Sandvik has accumulated a long history and experience in loading and hauling automation in underground mining. Since the late 1980s Sandvik has actively participated in several major research and development automation programs leading to the commencement of the development of an integrated system for semiautomated loading in 1999. Development work was later conducted to expand the capabilities of the system for automated hauling during 2001 and the AutoMine« system became commercially available. The first delivery of the AutoMine« system was completed in August 2004 in South America, where the system continues to operate in a full-scale production environment and is being expanded as the production area enlarges. Further systems have been delivered and are operational in North America, Africa and Europe. This paper focuses on the AutoMine« system deployed in Block 4 at De Beers Finsch Mine in South Africa. An overview of the mine and the process used to acquire the system and the key drivers which led to the selection of an automated solution are described. An overview of the initial system installation, subsequent expansions and future plans are presented. This is followed by a summary of the implementation and operational experiences associated with automated underground operations. The paper concludes by summarising the benefits that have been realised.

Jan 1, 2008

By S Casas Castellanos

"Tyres consumption is one of the costliest branches of the operation in a truck-based haulage mine. Off-the-road (OTR) tyres working within undesirable conditions have a considerable negative impact on the whole mine’s productivity. Only the rolling resistance due to underinflated tyres could increase truck fuel consumption by 15 per cent. The impact of other conditions such as road surface quality and temperature are difficult to estimate. Tyre management is a demanding activity that requires a high level of coordination between maintenance and production departments.The project is aimed to develop a smart decision tool to assist mine managers to optimise tyre resources. By identifying factors that have significant impact on tyres, managers are able to take timely action to mitigate undesirable working conditions.The proposed model utilises real-time tyre measurement of pressure, temperature, speed, load, deformation and surface profile to report tyre performance in terms of tonne-kilometre-per-hour (TKPH) and tyre longevity. Both indicators are permanently monitored in order to trigger a warning system designed to keep tyres under optimal working conditions.An interactive database ‘Octo-Mine’ wirelessly receives records from a programmable logic controller (PLC) deployed on the truck. PLC records are the integration of multiple sensor signals with a time stamp. Octo-Mine utilises real-time and historical tyre records to generate online performance and longevity reports, as well as preventative and corrective tyre maintenance scheduling, by comparing current tyre status with established standards.To validate the model, the prototype database was populated with hypothetical data to simulate ideal working conditions subject to comparison with real field observations. Additionally, a laser-based technology prototype device successfully measured a new 9 mm tyre tread and a 60 000 km rolled tyre tread in the laboratory.In conclusion, optimal tyre management contributes not only to reduction of tyre waste but also to truck energy efficiency. This project is a first step in proving these benefits under real field conditions. It suggests that further development of sensor equipment and its integration with a communication system is a worthwhile focus for future research.Citation:Casas Castellanos, S, 2016. Optimum Management of Truck Tyres in a Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 212–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By I Elias, E Moya, S Chaffer

This paper is based on a case study from a mine site that operates two gyratory primary crushers. These crushers were encountering problems, which included inconsistent P80, reduced liner life tonnage and, on some occasions, catastrophic failure of the liners.As part of an evaluation process, both crushers were ‘mapped’ using a technology for condition monitoring and modelling of the crusher’s wear components. The technology provides comprehensive coverage of the crusher’s concaves and mantle at 100 mm intervals. It also automatically assesses wear rate between inspections and determines the highest wear areas. Outcomes include projected optimum reline dates at target replacement thicknesses, the identification of asymmetrical wear patterns, and the accurate measurement of open and closed (OSS/CSS) side settings.A comprehensive study was performed to optimise the performance of both these crushers at site. Over a period of seven liner service lives, the strategies to improved performance included liner analysis (concaves and mantle profile analysis), tonnes per day (t/d) and tonnes per hour (t/h) analysis, mantle reutilisation, detection and control of loose concaves, and detection and control of uneven wear and hot spots.These strategies resulted in the improved mechanical and operational performance of both crushers through concave and mantle redesign, OSS/CSS control, accurate wear forecasting plus other initiatives.As a result of these initiatives, the site now experiences benefits which include consistent product size, increased tonnes per hour (t/h) for both crushers and the liner life tonnage has doubled. Additionally, further benefits include less downtime for crusher liner maintenance and the reduced cost of inventories by mantle reutilisation.CITATION:Elias, I, Chaffer, S and Moya, E, 2015. Improvements in service life and cost reduction for gyratory primary crushers through mantle and concaves optimisation – a case study, in Proceedings Iron Ore 2015, pp 115–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By E J. B van Etten

Pit lakes may form when open cut mining leaves a pit void that then fills with ground and surface waters. This often replaces terrestrial ecosystems that existed prior to mining with an aquatic ecosystem, affording an opportunity to improve regional aquatic biodiversity values through targeted aquatic restoration (McCullough and van Etten, 2011). Restoration theory provides guidance when restoring disturbed systems towards landscapes that are of regional value and relevance. But how do we identify a restoration target for a novel aquatic habitat that only exists in the new post-mining landscape? This paper presents a process of first identifying and then surveying local representative aquatic systems, to provide a direction for pit lake restoration efforts and achievement criteria for pit lake relinquishment, using a case study from a sand mining operation amongst wetlands in south-western Australia.The company mines silica sands following mechanical removal of topsoil and then extraction of the ore from below the watertable by dredging. Assessment of wetland and riparian vegetation was achieved through the establishment and measurement of temporary monitoring transects across five natural wetlands in the Kemerton area. Several more regional wetlands were also visited and observations made to supplement and validate these data.Distinct vegetation zonation was found across each wetland, although typically wetland basins were unvegetated or filled with younger woody plants with patchy distributions. Fringing riparian vegetation consisted of few species (commonly the paperbark Melaleuca rhaphiophylla and the sedge Lepidosperma longitudinale), but community composition and structure were variable between wetlands. The pattern of vegetation seen across natural wetlands was best explained by topography and soil chemistry, with low lying wetland areas more likely to experience regular flooding and accumulate organic matter and nutrients.In conclusion, where they are available, regional natural waterbodies may constitute the best valid restoration goal. Nevertheless, the goal may need to consist of a range of closure design opportunities, rather than a single target.

Oct 5, 2011

Madison Enterprises Corp. and Matu Mining are currently ex- ploring the Mt. Kare property in Papua New Guinea. The Mt. Kare gold prospect has had a short but very active history, since the first discovery of gold in the area in 1986 the property has sccn: a 3 year gold rush during which 10,000 alluvial miners re

Jan 1, 1997