Search Documents

By H. S. Bell

It seems unnecessary to dwell upon the advantages of the modern pipe still as compared with the older type of distillation equipment used by oil refiners. The relatively low installation cost, coupled with remark-able operating efficiencies of pipe stills, precludes the consideration of other types except in rare instances where some peculiarity of product or plant may have an influence. The question of the actual heat required to distil petroleum is quite involved. We have extensive data on the latent heats of the various hydrocarbons under different conditions of pressure. We also have information regarding the specific heats of various oils and the effect of temperature thereon. Because of the complexity of petroleum and of each fraction, it seems impossible to analyze theoretically the partisl-pressure effect of the great number of hydrocarbons upon one another during distillation. If a distillation curve and percentage analysis of any crude or product are available, it is possible to construct a curve with ordinates representing per cent. distilled and B. t. u. per pound or per gallon, or other desired unit. To do so the crude is split into fractions, of 5 or 10 per cent. The boiling point and gravity of each fraction being determined, it is possible to evaluate the heat required. As each fraction is removed, the residue must be raised to a higher temperature and latent heat supplied for the successive fraction. As the calculations progress, the latent heats decrease while the specific heats increase. Such a curve is illustrated by Fig. 1 for a typical 39.9° Be. North Texas crude. The chart is illustrative of batch distillation. Theoretically, if the oil were heated by a single flash in a pipe still, the partial-pressure effect of the light products would result in the removal of the same amount of vapors at a lower temperature. Practically, we find that because of the necessarily extensive fractionating equipment required when separating many products all in vapor phase, the oil has to enter the separator at temperatures corresponding to or even above those required in the batch still. Furthermore, in single-flash distillation the vapors evolved in the heater must be superheated to the outlet temperature. Very little is

Jan 1, 1928

By N. Standish

By contrast with viscometry and sedimentation, no actual measurements of the applicability of Stokes' law to steelmaking have ever been reported; instead, the proof for and against Stokes' law has been inferred from the frequently observed phenomenon that inclusions collect in the top scum and the bottom of ingots. As such proof is unsatisfactory, continued reference to Stokes' law in steelmaking, even as a model for calculating the terminal velocities of rising inclusions, should be avoided. In fact, all conclusions that have been reached regarding size, density, and viscosity on the flotation of inclusions could be made more rationally without Stokes' law. A worthwhile exception is that of Mitsche1 who in 1934 used Stokes' law to show not only the expected effects of size, density, and viscosity on flotation but also the beneficial effects of i) melting under a slag layer (now Electro Slag Refining); ii) treating melts with synthetic slags (Ref. 2 gives recent applications); iii) bubbling an inert gas through the melt (recent applications in Refs. 3 and 4); and iv) altering the solid/ liquid interface characteristics. At this point, it should again be emphasized that the boundary conditions for which Stokes' law was derived place enormous restrictions on the law but its application, as noted earlier, can yield useful results in some fields under certain conditions and within well-defined limits. When compared with inclusions, which may be solid or liquid, spherical or irregular, dispersed or coagulated, interacting between themselves and the melt, floating in a liquid which is in a state of motion of varying intensity5 and contained in vessels of various shapes and sizes that may change with time as in a solidifying ingot, the conclusion is obvious-Stokes'

Jan 1, 1969

By David T. Peterson

Calcium metal was found to deoxidize thorizcm at 1000° to 1200° C. The reaction kinetics were determilled and related to the diffusion coefficients of oxygen in thorium. The solubility of oxygen in thorium, the minimum oxygen concentration, and the diffusion coefficient were determined from 1000° to 1200°C. This firocess results in the lowest oxygen concentrations zohich have been reported for thorium metal. FOR many years it has been known that calcium metal will reduce thorium oxide to thorium metal. This reaction has been the basis for several methods of preparing thorium metal. From the equations giv-by Kubaschewski and vans, ' AF" for the reaction Cao, + Tho,(,) - CaO(,, + Th(,) was calculated and found to be -3.4 kcal at 1000°C, -2.5 kcal at llOO°C, and -2.0 kcal at 1200°c. Thorium is very slightly soluble in liquid calcium, and the solubility of calcium in solid thorium is very low. Consequently these metals would be in essentially their reference states. If thorium containing oxygen were equilibrated with liquid calcium between 1000° and 1200°C, the oxygen content of the thorium would have to be below the solubility limit in thorium. Oxygen is one of the impurities most difficult to remove from thorium and is the most abundant impurity in metal prepared by almost all known methods. Fortunately, oxygen does not have a large influence on the properties of thorium because the solubility in solid thorium is very low. EvenT in thorium containing 100 ppm of 0, particles of thorium oxide can be observed in the microstructure. In view of the incompatibility of thorium oxide and liquid calcium and the low solubility of thorium oxide in thorium, the deoxidation of thorium by this method was investigated. For thorium containing an amount of oxygen well in excess of the solubility limit, the reaction should proceed in the following sequence. The oxygen content of the thorium matrix near the surface would be depleted by the diffusion of oxygen to the surface. At the surface, the oxygen would react with calcium to form calcium oxide. To maintain equilibrium within the thorium, thorium oxide would dissolve to keep the matrix saturated. Consequently, the thorium-oxide particles would disappear first at the surface and then the particle-free rim would grow in thickness. If the rate-controlling step were the diffusion of oxygen through this layer of thorium which was growing in thickness in direct proportion to the amount of oxygen removed, the well known parabolic time law should be observed. If the oxygen concentration at the surface of the thorium and at the inner surface of the deoxidized rim were known, the diffusion coefficient of oxygen in thorium could be calculated from the parabolic rate constant. EXPERIMENTAL PROCEDURE The thorium metal used in this study was prepared by calcium reduction of ThF, by the method described by Wilhelm.' The analysis of this metal is given in Table I. The carbon was determined by combustion, the oxygen by the HC1-insoluble residue method, nitrogen by the Kjeldahl method, and the other elements by emission spectroscopy. A section of this ingot was hot rolled at 600°C to 1/4 and 1/8-in. thick plates. Specimens approximately 7/8 in. square were cut from these plates, and all surfaces of the specimens were cleaned and smoothed by filing with a clean file. Individual specimens were placed in 1-in. diam by 2-in.-long tantalum capsules. Approximately 1 g of clean, high-purity calcium was placed in the capsules and an end closure arc-welded in place. The tantalum capsules were sealed in Inconel crucibles to protect the reactive metals from oxidation. The entire loading procedure was done in a glove box filled with pure argon. The loaded crucibles were placed in a muffle furnace, controlled within 2OC of the desired temperature, for a measured length of time. After the specimen had cooled to room temperature, it was sectioned perpendicular to the large faces and through the mid-point of two of the sides. The sectioned specimen was mounted and polished through Linde A abrasive. The rim which was free of thorium-oxide particles could be clearly observed microscopically as mechanically polished. Twenty measurements of the thickness of the rim were made at equally spaced points far enough from the end of the

Jan 1, 1962

By A. Wahab Khair

This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally con- fined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage.

Jan 1, 1984

By Norman Pilling

The micrographic analysis of silicon steels is possible if a dilute solution of nitric acid and methyl alcohol in nitrobenzol is used. The action of this reagent differs from that of sodium picrate in that there is no persistent deep-seated staining and the solution is used cold. THE technical difficulties hampering the metallographic analysis of silicon steels are chiefly the result of the extreme corrodibility of these alloys. The addition of silicon to iron in increasing quantities, up to about 6 per cent., rapidly increases the susceptibility of the alloy to chemical attack, not only in acid solution, but in water. This renders the preparation of metallographic sections very difficult, because of a non-selective attack upon the finely polished surface by the water used as a lubricant in polishing. This water attack masks the true structural details revealed by suitable etching reagents. It is thus necessary to use alcohol as a polishing lubricant in the last stages of preparation and to avoid all etching reagents having an aqueous base. A specific reagent for the identification of iron carbide in ferrous alloys, and the one hitherto used almost exclusively by metallurgists, is an alkaline aqueous solution of sodium picrate, which stains this constituent selectively. Its application to silicon steels has not proved successful, as its distinctive selective action is more or less completely hidden by the general attack of the aqueous solvent on the silico-ferrite, greatly accentuated by the fact that this reagent must be used at its boiling temperature (105° C.). Thus, a powerful metallographic aid to the study of the higher silicon alloys, such as transformer steels, is lost. A new reagent has been developed for the purpose of overcoming this difficulty. It is with some hesitation that the list of etching reagents, already overburdened, is increased, but the properties of this new reagent are advantageous in several ways and a definite field for it may be found in the metallography of ferrous alloys.

Jan 1, 1924

By P. A. Witherspoon, R. W. Donovan, T. D. Mueller

The use of petroleum-barren aquifers for underground storage has become extremely important to the natural-gas industry. A critical problem in assessing the feasibility of a specific aquifer for such use is the permeability determination of the caprock over the proposed storage project. The approach used here is to conduct both static and dynamic field tests on the aquifer being analyzed. Valuable information on the possibility of communication between the storage aquifer and any other aquifers above can be obtained by measuring hydrostatic water levels and water analyses. Significant differences in such data give evidence of the lack of communication between the intended storage reservoir and other horizons. The dynamic approach requires that one well be pumped in the storage aquifer, and changes in fluid levels recorded in both the aquifer and its caprock. The interpretation of the data from such pumping tests involves the solution of nonsteady radial flow in an infinite aquifer and the influence on such flow of a leaky caprock. A finite-difference model has been used to investigate this problem, and the transient behavior has been solved numerically with a digital computer. It has been found that the pressure transients in the storage aquifer are not affected significantly by moderate caprock leakage. The pressure behavior of the caprock is a much better indicator of the degree of leakage, and generalized solutions for this behavior are included. Field data are presented to demonstrate both the static and dynamic approach. If is concluded that appropriate investigation of the groundwater hydrology in an aquifer-type gas-storage project can provide much valuable information for determining the effectiveness of the caprock to hold gas. INTRODUCTION Underground storage of natural gas in the United States has been developing at a rapid rate over the past few years. In 1955, the total gas-storage capacity was about 1.6 trillion cu ft; by 1961, this figure was almost 3.2 trillion cu ft, an increase of 100 per cent in six years.' This trend un- doubtedly will continue because the economics favor the development of gas storage, as opposed to the construction of new pipelines, to meet the inherent cyclic demand for fuel in the metropolitan areas of this country.' About 15 per cent of the current underground gas storage has been developed in petroleum-barren aquifers, i.e., geological domes or anticlines in which no commercial quantities of oil or gas had been produced prior to the storage operations. The necessity for using barren aquifers outside many metropolitan areas of this country has been due to the lack of depleted oil or gas fields that were near enough and large enough to meet the demands of such consuming areas. Pipeline companies have developed aquifer storage along their transmission lines to meet the fluctuating needs of their complex systems. Considerable thought has also been given to the problem of storing gas in a structureless aquifer, both in this country' and in the Soviet Union outside the city of Leningrad.'," Conditions such as these have led to the development of aquifer gas-storage projects in many parts of the U. S. Most of these developments have centered in the Mid-Continent area, and the greatest amount of activity has been concentrated in Illinois.6 Thus, the use of petroleum-barren aquifers for gas-storage purposes has become extremely important to the natural-gas industry. There are three basic problems in developing aquifer-type storage: (1) finding an adequate geologic structure, (2) finding a suitable storage reservoir within the structure and (3) determining the tightness of the caprock over the intended storage zone. The first two problems can be solved by applying conventional methods of exploration geology, but once these problems are solved, the question arises as to why no oil or gas is present in an otherwise favorable setting. Two situations are possible: (1) an adequate source bed was never present, or (2) a source bed was present but the petroleum seeped away because of a leaky caprock. Determining the tightness of the caprock is one of the most critical problems in assessing the feasibility of a specific aquifer for storage purposes. In attacking this problem, one usually takes cores of the caprock and subjects them to a rigorous investigation. Such core data are desirable, but they only detail the matrix properties and cannot be expected to reveal the gross characteristics of the caprock. Several gas-storage projects in the U. S. have had considerable leakage where

By B. Zondek, W. T. Cardwell, J. W. Sheldon

The fundamental equations that are used to describe two-phase fluid flow in porous media are Darcy's law for each phase and an equation of continuity for each component. The special case of one-dimensional, incompressible, two-phase flow has received much attention in the petroleum engineering literature.1-10 The basic paper on the subject is that of Buckley and Leverett.2 Buckley and Leverett showed that one could eliminate the pressure and obtain a single partial differential equation for the saturation. They solved this equation for the case when gravity and capillary forces are negligible. A frequently encountered property of the solution of the basic partial differential equation is that, as time progresses, the saturation becomes a multiple-valued function of the distance coordinate, x. Buckley and Leverett interpreted the formation of multiple values as an indication that the saturation-distance curve had be-come discontinuous. They developed a method of determining the position of the discontinuity from a material balance. We solve the Buckley-Leverett partial differential equation using the method of characteristics and the concept of shocks. Our treatment is analogous to treatments used in the theory of supersonic compressible flow." Although the numerical results obtained are the same as those obtained by previous methods, we believe that this approach is more logical and has broader applicability. It can, for example, be generalized to treat the case when the fluids are compressible. It is not clear how one would go about doing this using the method of Buckley and Leverett. To illustrate the power of the method of characteristics with shocks, we solve a problem in gravity segregation which has not been treated previously in the literature. A special case of the general method developed here was used by Welge, to solve a particular fluid displacement problem. We consider two-phase incompressible flow along the vertical direction x in a porous medium. We assume that there is no flow transverse to .x. We measure positive in the upward direction. The fundamental equations are obtained from Darcy's law and the mass conservation law. Since the two phases are incompressible, mass conservation is equivalent to volume conservation.

W. 0. HOTCHKISS, * Madison, Wis.-It was fortunate, in a way, that this subject of income taxation came up during the war when the government could appeal, on the basis of patriotism, to men of large, business experience to undertake the work of formulating this matter and practically donate their services. At any other time the government would have been unable to secure the necessary number of men of like ability. There is one thing that must not be forgotten. In all cases, except the very largest and most important, the application of this income tax law to a mine is going to be made by clerks whose salaries are fixed by a Congress that appropriated a half billion of dollars for a war purpose and provided that $4000 should be the highest salary paid in the adminis-tration of that great sum. The Congress of the United States unfor-tunately seems almost entirely unaware of the fact that men of ability and experience are worth money and must be paid adequately if proper public service is to be secured. While the formulation of the broad plans for administering the law have been in the hands of. men of unusual ability, we have the future to guard, and, if possible, the mining industry should see to it that the Internal Revenue Department is permitted by Congress to pay salaries that will enable it to secure men of the ability and experience necessary to insure proper consideration of the industry. Another fact to which I would call attention is the difference between the business and the economic, or economists', points of view as to what a mine is. The economists have properly, from their point of view, classed a mine as a wasting asset, but the average metal mine is not a wasting asset if it is a real mine. The economists are correct in a broad sense in that every ton of ore taken out diminishes the orebody by that amount. When it comes to the consideration of an individual mine from the business standpoint, the future of that mine rests on unfore-seeable events-the discovery of new orebodies or the development of old bodies beyond the point of probable expectations. Every going mine must develop new ore each year to replace that extracted, and, .during all but the last one or two years of its activity, actually does so. Instead of being a "wasting asset" such a mine, from the practical stand-point which must control valuation, is an "increasing asset." From

Jan 12, 1919

By Donald W. Gentry, John F. Abel

This paper presents some of the results of a rock mechanics instrumentation program designed for, and implemented at. longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam, and immediately below the coal seam. Longwall test panel 4N had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft), [Fig. 1]. The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) although it ranges from 73-134 m (240-440 ft). Roof support at the face was provided by 116 Hemscheidt 320 HSL shields. These shield-type supports weigh 11.4 metric tons each.

Jan 1, 1979

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

The a-p type alloys are subject to a loss of tensile ductility with increasing hydrogen content. No hydride phase is visible in embrittled a-B type alloys. The embrittlement encountered appeared to be of the strain-aging type. Both compositional and structural factors are shown to influence the hydrogen tolerance of a-B type alloys. IN previous papers by the authors, the effects of hydrogen on the structure and mechanical properties of high-purity and commercial-purity titanium were described. It was shown that the presence of hydrogen in these materials results in a hydride phase having low solubility at room temperature. This insoluble phase had little effect on the room temperature tensile properties, but did decrease the notch-bar toughness to a large degree. The binary Ti-H systemz indicates that hydrogen is much more soluble in £ than in a-titanium. Hence, it is not expected that the embrittling effects of hydrogen in a-fi alloys will be similar to that found in a alloys. Materials of this type studied in the present investigation included two commercial a-/3 alloys, Ti-8Mn and Ti-4A1-4Mn; three high-purity Ti-Mn alloys containing 3, 6, and 9 pct Mn; and four high-purity Ti-Mo alloys, Ti-SMo, Ti-10.9M0, Ti-13.1 M0, and Ti-20M0, of the a-B and B types. Materials and Fabrication—The high-purity base alloys, composed of iodide titanium and high-purity metals, were prepared by double arc melting under argon in a water-cooled copper crucible, using a water-cooled tungsten electrode. Radiographic examination showed homogeneous Ti-Mo alloys. The analyses of the alloys used in this investigation and their as-fabricated hydrogen content, where determined, are listed in Table I. The two commercial alloys were 1/2 and % in. diam bar stock. No analyses other than hydrogen content were made. In order to maintain the a-B relationship existing in the two commercial alloys, vacuum annealing and hydrogenation were carried out in the B field prior to final fabrication. Fabrication then was done by The three high-purity Ti-Mn alloys were forged to 3/4 in. diam rods at 1600°F, and hot swaged to 1/2 in. diam at 1380°F. Machined and degreased bar stock was vacuum annealed or hydrogenated, fabricated to 1/8 in. diam rod by hot swaging, annealed in argon for 1 hr at 1380°F !75O°C), and water quenched. The six yz lb Ti-Mo ingots were forged to Wi in. diam rods at 1600°F and then hot swaged to % in. diam. Machined and degreased specimens were vacuum annealed or hydrogenated in the /3 field, prior to fabrication, by swaging to Y4 in. rod at 1400°F. After fabrication, the 5 and 10.9 pct Mo alloys were annealed in argon for 16 hr at 1290°F and water quenched to give equiaxed a-B structures. The higher molybdenum content alloys were argon annealed 4 hr at 1470°F and water quenched to give all £ structures.

Jan 1, 1957

By Benjamin Lustman, Robert F. Mehl

The study of the high-temperature oxidation of pure metals, intensively pursued experimentally since the pioneer work of Pilling and Bedworth1 and supplemented by the recent theoretical work of Wagner2 is now well advanced. The important field of low-temperature oxidation—i.e., oxidation extending only through the temper color range of thicknesses with the formation of thin oxide layers in the range from 0 to 1000-2000 ?ngstroms—has not, however, reached so satisfactory a state, owing largely to the experimental difficulties that attend the formation and study of thin films; most of the work has been performed on abraded specimens whose surface irregularities approximated the thickness of the films formed. It has been pointed out that the rates of oxidation of different crystal faces are different and that the difierence may be related to the orientation relationships that obtain between the metal crystal and the superimposed oxide crystal; it has also been suggested that this orientation dependence should manifest itself in rates of oxidation and perhaps also of corrosion in aggregates bearing preferred orientations.3'4 An attempt to measure the rates of oxidation of different crystal faces of alpha iron demonstrated this difference in rate,4 but the dependence of rate on orientation was not simple; the method of measuring thickness, consisting of a color comparison with barium stearate multi-films of known thickness, was not wholly satisfactory. For these reasons it was felt that a study of the rate of oxidation of single crystals prepared with surfaces as smooth as possible, using a sensitive method giving true film thickness, should be profitable. Copper was chosen because of the ease of reduction of the primary oxide film and because the orientation relationships between metal and oxide and the composition of the oxide films formed at low temperatures are known; for thin films formed at low temperatures, Cu2O alone occurs.22-24 Experimental Procedure Various methods of surface preparation were attempted in order to obtain a surface that would oxidize uniformly and repro-ducibly. Electrolytic polishing by the method of Jacquet5 and electrolytic and mechanical polishing followed by annealing in vacuum and in purified hydrogen at various temperatures were tested. The procedure finally adopted consisted in a fine metallographic polish followed by an anneal in purified hydrogen at temperatures of 900° to 1000°C. for 12 hr. or more. The surface so produced was very bright and smooth, with no trace of specular etching (though some grain-boundary etching was observed); indeed, fine scratches produced by the final polish were entirely removed by the high-temperature anneal. After this treatment, the specimens were cooled in hydrogen to room temperature and placed in the oxidation furnace, where

Jan 1, 1941

By S.H. Ash, P.S. Miller

Extensive and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past I0 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the Succdeding face, constituting a round. Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons" tunne1ing is more hazardous than mining in any branch of the mineral industry. On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. The Delaware Aqueduct The new Delaware aqueduct is a Manhattan project of some magnitude; when regular it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1943

By P. S. Miller, S. H. Ash

Extensive and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past I0 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the Succdeding face, constituting a round. Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons" tunne1ing is more hazardous than mining in any branch of the mineral industry. On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. The Delaware Aqueduct The new Delaware aqueduct is a Manhattan project of some magnitude; when regular it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1943

By Benjamin Lustman, Robert F. Mehl

The study of the high-temperature oxidation of pure metals, intensively pursued experimentally since the pioneer work of Pilling and Bedworth1 and supplemented by the recent theoretical work of Wagner2 is now well advanced. The important field of low-temperature oxidation—i.e., oxidation extending only through the temper color range of thicknesses with the formation of thin oxide layers in the range from 0 to 1000-2000 ?ngstroms—has not, however, reached so satisfactory a state, owing largely to the experimental difficulties that attend the formation and study of thin films; most of the work has been performed on abraded specimens whose surface irregularities approximated the thickness of the films formed. It has been pointed out that the rates of oxidation of different crystal faces are different and that the difierence may be related to the orientation relationships that obtain between the metal crystal and the superimposed oxide crystal; it has also been suggested that this orientation dependence should manifest itself in rates of oxidation and perhaps also of corrosion in aggregates bearing preferred orientations.3'4 An attempt to measure the rates of oxidation of different crystal faces of alpha iron demonstrated this difference in rate,4 but the dependence of rate on orientation was not simple; the method of measuring thickness, consisting of a color comparison with barium stearate multi-films of known thickness, was not wholly satisfactory. For these reasons it was felt that a study of the rate of oxidation of single crystals prepared with surfaces as smooth as possible, using a sensitive method giving true film thickness, should be profitable. Copper was chosen because of the ease of reduction of the primary oxide film and because the orientation relationships between metal and oxide and the composition of the oxide films formed at low temperatures are known; for thin films formed at low temperatures, Cu2O alone occurs.22-24 Experimental Procedure Various methods of surface preparation were attempted in order to obtain a surface that would oxidize uniformly and repro-ducibly. Electrolytic polishing by the method of Jacquet5 and electrolytic and mechanical polishing followed by annealing in vacuum and in purified hydrogen at various temperatures were tested. The procedure finally adopted consisted in a fine metallographic polish followed by an anneal in purified hydrogen at temperatures of 900° to 1000°C. for 12 hr. or more. The surface so produced was very bright and smooth, with no trace of specular etching (though some grain-boundary etching was observed); indeed, fine scratches produced by the final polish were entirely removed by the high-temperature anneal. After this treatment, the specimens were cooled in hydrogen to room temperature and placed in the oxidation furnace, where

Jan 1, 1941

By J. D. Livingston, J. J. Becker

A MAJOR difficulty in the experimental study of precipitation-hardening is the measurement of particle sizes too small to be easily resolved with the microscope. It has been shown recently, however, that magnetic measurements on copper-cobalt al- loys in the aged state can be used to determine the average volume, total volume, volume distribution, and shape of the ferromagnetic cobalt-rich particles, even though the particles are submicroscopic in size. r' These alloys also are known to exhibit considerable precipitation hardening. This paper reports some results on the dependence of the mechanical properties of such an alloy on the particle size, determined magnetically. It further illustrates the use of other magnetic measurements in interpreting structure changes occurring during deformation.

Jan 1, 1959

By R. W. Hyde, S. E. Eaton, B. S. Old

One of the most important problems facing the steel industry at the present time is that of maintaining at a minimum the sulphur content of many grades of steel where sulphur is known to have harmful effects On both quality and yield. The present outlook in this struggle to reduce the amount of sulphur in steel is rather gloomy since the sulphur content of the raw materials available in the United States is gradually rising, with little relief in sight. A flow sheet of sulphur in the steel process is shown in Fig I. The values used here were obtained by averaging coke oven and blast furnace data at No. 5 furnace in Cleveland and are considered typical for high top pressure practice. The sulphur evolved in the blast furnace top gas was obtained by difference and since the amount is relatively small, little significance should be attached to this particular value. From Fig I it is apparent, however, that coals used in the production of metallurgical coke represent by far the largest single source of sulphur in steel-making. As an indication of the decrease in quality of these coals as regards sulphur content the weighed average annual sulphur analysis of the coals supplied to two different steel plants, since 1925, is plotted in Fig 2} The sharp rise since 1940 is strikingly apparent. Another indication of this trend is found in estimates of coking coal reserves. Thus in the case of Pittsburgh seam coals available in Allegheny, Fayette, Greene, Washington, and Westmoreland Counties in Pa. as of Jan. 1937 only 25 pct of the coal reserves would contain less than 1.50 pct sulphur after washing.2.3 Many of these lower sulphur reserves have been seriously depleted in recent years because of accelerated war demands. still another demonstration of the increasing sulphur content of coals on a country-wide basis is found in a report by the Bureau of Mines4 which shows a steady increase in the sulphur content of coke made in the United States. It should be noted that this increase continues in spite of the wider use of coal washing in recent years. Sulphur occurs in coal in three forms, pyritic (FeS2), organic sulphur, and a small amount of sulphate sulphur (CaS04). The sulphur is subsequently found in the coke in combination with carbonaceous material of is composition and as calcium and iron sulphides' In considering the general problem of sulphur elimination, the Republic Steel Corp. was interested in determining which, if either, of the two major forms of sulphur in coal contributes the greater portion of sulphur to the coke. Since the ratio of pyritic to organic sulphur varies widely in different coals, it was thought that if it could be shown definitely that the major part of the sulphur occurring in coke originates from one of the two ""jar forms of sulphur in the coal, it would then be possible to select with confidence coal which, although high .in total sulphur, would yield coke of fairly low sulphur content. Using the new

Jan 1, 1949

By R. L. Stephenson

The effect of fabrication variables on the creep-rupture properties of TZM (Mo-0.5 pct Ti-0.08 pct Zr-0.03 pct C), Cb-TZM [columbium-modified TZM (7140-1.5 pct Nb-0.5 pct Ti-0.8 pct Zr-0.05 pct C)], and TZC (Mo-1.2 pct Ti-0.25 pct Zr-0.15 pct C) has been studied at 982º. 1093º, 1204º, and 1315°C for rupture times up to 1000 hr. The creep tests were performed in vacuum creep furnaces, employing cold-trapped oil-diffusion pumps, operating at pressures 2 X 10-7 tory. After-test chemical analyses showed no significant changes in interstitial content. The creep-rupture properties of TZM, fabricated according to current mill practice, were determined in the stress-relieved and in the re crystallized conditions to provide control data. Specimens of TZM, Cb-TZM, and TZC fabricated according to each of two experimental fabrication schedules were then tested. The schedules differed in terms of in-process annealing temperatures and warm -working temperatures. The data make several conclusions evident. Fabrication variables do indeed have a profound effect on the long-time creep-rupture properties of molybdenum alloys. Strengths of these alloys compare very favorably with those of other refractory metal alloys in the temperature range studied. FOR several years we have been engaged in the evaluation of the creep-rupture properties of promising refractory metal alloys. We consider the determination of these properties to 1000 hr at several temperatures necessary for a valid comparison. Such an evaluation indicated that the creep strengths of Mo-0.5 pct Ti and TZM (Mo-0.5 pct Ti-0.08 pct Zr-0.03 pct C) compare favorably with those of other refractory metal alloys. Tensile and recrystallization data of other investigators1,2 show an effect of fabrication variables. More specifically, those fabrication schedules which produce high strength through work hardening exhibit the least thermal stability. A similar conclusion was reported by perkins3 for Cb-TZM. This would lead one to expect that, in terms of creep, those materials showing higher strength at short times and low temperatures would exhibit lower strength at long times and high temperatures. If these expectations were fact, a substantial improvement could be made in these alloys by optimizing their fabrication schedule in terms of their anticipated service temperature. We therefore undertook a study of the effect of fabrication variables on the long-time creep properties of TZM, Cb-TZM (Mo-1.5 pct Cb-0.5 pct Ti-0.08 pct Zr-0.05pct C) and TZC (Mo-1.2 pct Ti-0.25 pct Zr-0.15 pct C). MATERIALS All materials used were supplied by the Climax Molybdenum Co. of Mich. Our original intention was to test the same heat of each alloy in different conditions. Fabrication difficulties prevented this; however, heats with nearly identical analysis were selected. The compositions of the materials used are listed in Table I. All materials were supplied in the

Jan 1, 1970

By E. T. Turkdogan, P. Grieveson

Molten silver is equilibrated with silicon nitride at 1400°C in nitrogen + hydrogen gas mixtures, and from the solubility data the activity coefficient of silicon is found to be 1.76 at silicon concentrations below 1 pct. Using this value, and that available from the silicon cmbide solubility measurements, together with those derived from the phase equilibrium diagvam, the activities of silver and silicon are estimated for the entire composition range. The main feature of the activity data is that there is a pronounced positive deviation from ideality. The activity of silver in molten silver containing up to 5 pct Si was determined by Schadel, Derge, and Birchenall1 by measuring the vapor pressure of pure silver and of the alloy over a temperature range of 850º to 1050°C. They deduced from their results that there is a positive deviation from Raoult's law and that the activity coefficient of silver increases with decreasing temperature. However, as pointed out by Kubaschewski and Catterall,2 their activity coefficients are much too high, giving silver activities greater than unity. At a later date McCabe and Birchenal13 showed that the previous vapor pressure data on silver4 were high by a factor of about 1.3; presumably a similar error must have occurred with the vapor pressure measurements on the Ag-Si alloys. The activities of silicon and silver calculated by tager' from the phase diagram and by Gibbs-Duhem integration, respectively, show a positive deviation from Raoult's law for silicon activity and positive and negative deviations for the silver activity. According to these computations, at infinite dilution of silicon ygi = 1.12 at 1420°C. d'Entremont and chipman6 measured the solubility of silicon carbide in molten silver at unit carbon activity; the equilibrium silicon content is found to be Nsi = 0.017 ± 0.002 atom fraction for 1420°C. Using the data of Grieveson and Alcock7 for the free energy of formation of silicon carbide from pure silicon and graphite, the activity of silicon for unit activity of carbon and of silicon carbide is asi = 0.0308 at 1420°c; therefore for the above solubility data on silver, YSi = 1.81, which is somewhat higher than that given by Hager. Use is often made of silver alloys in the measurements of activities of solutes in metals where silver has a very low solubility; in fact, Ag-Si and Ag-A1 alloys have been used in the past for such purposes. In an attempt to gain more thermodynamic data on molten Ag-Si alloys, measurements have been made in the present study on the solubility of silicon nitride in molten silver; the results on these solubilities are given in this paper together with a detailed discussion of activities of silver and silicon. SOLUBILITY OF SILICON NITRIDE The standard free energy of formation of silicon nitride is known with a reasonably high degree of accuracy. According to the measurements made by Hincke and Brantle8 and by Pehlke and Elliott,' the following are the free energy data for the standard states of solid Si3N4, liquid silicon, and Nz at 1 atm pressure:

Jan 1, 1963

By R. W. Hyde, B. S. Old, S. E. Eaton

One of the most important problems facing the steel industry at the present time is that of maintaining at a minimum the sulphur content of many grades of steel where sulphur is known to have harmful effects On both quality and yield. The present outlook in this struggle to reduce the amount of sulphur in steel is rather gloomy since the sulphur content of the raw materials available in the United States is gradually rising, with little relief in sight. A flow sheet of sulphur in the steel process is shown in Fig I. The values used here were obtained by averaging coke oven and blast furnace data at No. 5 furnace in Cleveland and are considered typical for high top pressure practice. The sulphur evolved in the blast furnace top gas was obtained by difference and since the amount is relatively small, little significance should be attached to this particular value. From Fig I it is apparent, however, that coals used in the production of metallurgical coke represent by far the largest single source of sulphur in steel-making. As an indication of the decrease in quality of these coals as regards sulphur content the weighed average annual sulphur analysis of the coals supplied to two different steel plants, since 1925, is plotted in Fig 2} The sharp rise since 1940 is strikingly apparent. Another indication of this trend is found in estimates of coking coal reserves. Thus in the case of Pittsburgh seam coals available in Allegheny, Fayette, Greene, Washington, and Westmoreland Counties in Pa. as of Jan. 1937 only 25 pct of the coal reserves would contain less than 1.50 pct sulphur after washing.2.3 Many of these lower sulphur reserves have been seriously depleted in recent years because of accelerated war demands. still another demonstration of the increasing sulphur content of coals on a country-wide basis is found in a report by the Bureau of Mines4 which shows a steady increase in the sulphur content of coke made in the United States. It should be noted that this increase continues in spite of the wider use of coal washing in recent years. Sulphur occurs in coal in three forms, pyritic (FeS2), organic sulphur, and a small amount of sulphate sulphur (CaS04). The sulphur is subsequently found in the coke in combination with carbonaceous material of is composition and as calcium and iron sulphides' In considering the general problem of sulphur elimination, the Republic Steel Corp. was interested in determining which, if either, of the two major forms of sulphur in coal contributes the greater portion of sulphur to the coke. Since the ratio of pyritic to organic sulphur varies widely in different coals, it was thought that if it could be shown definitely that the major part of the sulphur occurring in coke originates from one of the two ""jar forms of sulphur in the coal, it would then be possible to select with confidence coal which, although high .in total sulphur, would yield coke of fairly low sulphur content. Using the new

Jan 1, 1949

By W. O. Philbrook, K. Natesan

The oxidation kinetics of spherical pellets of zinc sulfide made from Santander concentrates were studied using a thermogravimetric technique. The experiments covered a temperature range-. of 740" to 102O°C, 0-N mixtures varying from 20 to LOO pct O2, and pellet diameters between 0.4 and 1.6 cm. Mathematical models were formulated to Predict the reaction rate on the assumption that a single transport or interface reaction step was rate -controlling. Analysis of the data indicated that the process of oxidation was predominantly controlled by transport through the zinc oxide reaction-Product layer. ROASTING processes, which are reactions between solids and gases, are very important because they are employed in the production of a number of basic metals. These processes are highly complicated, and one needs to consider the transport phenomena of heat and mass between the solids and gases in addition to the kinetics of various chemical reactions involved. Because of such complications there is a lack of knowledge concerning the rate-limiting factors, which may strongly depend on temperature, particle size, gas composition, and solid structure. The oxidation of zinc sulfide, which is of commercial importance in zinc production, falls into this class of reactions. The major goal of this work was to elucidate the roles played by different process variables, such as reaction temperature, gas composition, pellet size, and pellet porosity, on the kinetics of oxidation of single pellets of zinc sulfide. Roasting of zinc sulfide single particles has been a subject of both experimental and theoretical investigations.&apos;-&apos; The reaction is exothermic and may be considered to be irreversible. Such a reaction has been found to proceed in a topochemical manner. In other words, as the reaction proceeds, a progressively thicker outer shell of zinc oxide is formed, while the inner core of unreacted sulfide decreases. It has been found experimentally, both in the present work and in the previous investigations,1-9 that the particle retains its original dimensions and the process requires transport of gaseous oxygen across the porous product layer for continued reaction. The reaction may be represented by ZnS(s) + 3/2 O2(g) = ZnO(s) + SO2(g) [1] The solid product considered here is only zinc oxide, since the diffraction patterns of zinc sulfide pellets oxidized partially at &apos;798" and 960°C showed K. NATESAN, Junior Member AIME, formerly St. Joseph Lead Fellow, Department of Metallurgy and Materials Science, Carnegie-Mellon University, Pittsburgh, Pa., is now at Argonne National Laboratory, Argonne, Ill. W. 0. PHILBROOK, Member AIME, is Professor of Metallurgy and Materials Science, Carnegie-Mellon University. This paper is based on a them submitted by K. NATESAN in partial fulfillment of the requirements for the Ph.D. degree in Metallurgy and Materials Science at Carnegie-Mellon University. Manuscript submitted December 2, 1968. EMD lines corresponding to original zinc sulfide and the newly formed zinc oxide. OXIDATION MODEL The generalized model for gaseous oxidation of zinc sulfide is illustrated in Fig. 1. This depicts a partially oxidized sphere of zinc sulfide in a gas stream surrounded by a laminar film of gas. The spherical sample of zinc sulfide of unchanging external radius r0 is suspended in a flowing gas stream of total pressure PT and composition specified by the partial pressures of the individual components. Partial pressures of the gaseous species in the bulk gas phase, at the exterior surface of the pellet, at the ZnS/ZnO interface, and at equilibrium for Reaction [I] are identified by the superscripts b, o, i, and eq, respectively. The overall reaction involves the following ~te~s:&apos;~&apos;~&apos; Step 1. Transfer of reactant gas (oxygen) from the bulk gas stream across the gas boundary layer to the exterior surface of the pellet and the reverse transfer of the product gas (sulfur dioxide). Step 2. Diffusion and bulk flow of oxygen from the pellet surface through the product shell (ZnO) onto the ZnS/ZnO interface and the reverse transfer of sulfur dioxide. Step 3. Chemical reaction at the interface, which results in consumption of oxygen gas and generation of sulfur dioxide gas and heat; at the same time the _________ PARTICLE SURFACE / x^^^^n^X / MOVING INTERFACE core-----/ sJSNxy " /T^T^02 \ V\V$\ ^NWX/ "*/— GAS BOUNDARY x. \\ZnO SHELLV/ / \^ . / &apos; ^ BULK GAS --------N_______ _____,------p£ w \ P« / (f> \ / a \ <i) / <----------------- _(o) ^^--------------(b) °- pso, pso2 ro ri 0 ri ro RADIAL POSITION Fig. 1—Generalized model for oxidation of a sphere of zinc sulfide.

Jan 1, 1970