Search Documents

By Donald W. Mitchell

Research shows that water neutralizes the explosion hazard of coal dust when present in sufficient quantity and when intimately mixed with the dust. The quantity of water required to neutralize coal dust and coal-rock dust mixtures is about equal to the limiting moisture adsorptive capacity of the dust; the adsorptive capacity increases with increase in the fineness and volatile content of the coal. Pools of water or high atmospheric humidity do not reduce the explosion hazard. Although wetted dust is less dispersible than dry dust, poor dispersibility cannot be relied on as the sole safeguard against explosion. Dust mixtures that contain water in excess of their limiting adsorptive capacity are dispersed and ignited by severe initiation sources. Pure coal dust adsorbs water with difficulty and retains water poorly; adsorption and retention is increased by the addition of rock dust the coal; the rock dust agglutinates wetted coal and assures that incombustible is present should drying occur. Therefore, it is advantageous to rock-dust wet areas in bituminous coal and lignite mines. When coal-rock dust mixtures are wetted and subsequently dried, the explosion hazard is about the same as for dust which was not wetted.

Jan 1, 1962

This report is the 25th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations, and the 7th of these reports to be issued on a calendar-year basis.3 It reviews briefly work in progress during 1960, and furnishes references to publications by Bureau personnel during 1960 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned can be found by referring to the publications cited in the footnotes or in the further list in the Miscellaneous section; other phases of work are reported here for the first time and will be covered in more detail by later publications, Coal programs of the Bureau of Mines extend over the wide range of theoretical and applied studies indicated by the table of contents. Fundamental research on coal structure and on the properties of coal will, over a period of time, increase the general knowledge about coal Which scientists and engineers may use in answering practical questions and in solving problems in the mining and utilization of coal. More applied studies are conducted in connection with the developement and evaluation of new mining techniques and the effective processing and utilization of coal and of coal products. Health and safety activities, analyses of coal being mined, and technical advice and assistance to Federal agencies in connection with fuel and boiler-water problems are among the practical services handled by the Bureau.4 5

Jan 1, 1962

By E. L. Rawlins

Systematic leakage surveys of natural-gas transmission lines not only aid in the conservation of gas, but can be made to show direct financial returns of large magnitude. 1. Such surveys reveal the actual leakage from the lines, and indicate repairs to be made in order, to eliminate unnecessary waste. 2. Tests on lines, after repairs are made, show the actual saving that has been accomplished. 3. Tests on newly constructed lines reveal the presence of leakage that should be eliminated before the lines are put into service.

Jan 1, 1926

By Virgil Marple

In the summer of 1979 the University of Minnesota Mobile Laboratory (UMML), designed for the analysis of airborne particles and gases was used to study fugitive dust from an open pit coal mine. The analysis consisted of determining the particle size distribution and concentration of dust from various mining operations, such as blasting, draglines, loading, roadways and bottom scrapers. For some operations the particles size distribution and concentrations were determined at varying distrances. Details of the dust concentration within the plumes as the plume passed the UMML were measured with an optical particle counter. For line sources, such as roadways this enabled the calculation of the particle flux at the sampling location. In addition to the standard instruments associated with the UMML, the applicability of some new instruments were investigated. These included a uniform deposit cascade impactor and a flux meter. Finally, a technique in identifying plume origins which utilized elemental X-ray flourescence analysis of filter samples was shown to be effective.

Jan 1, 1980

By E. C. Perkins

As part of a program for developing methods of using domestic titanium deposits, the Bureau of Mines investigated methods for chlorinating titanium slags prepared from titaniferous minerals by electrosmelting. Titaniferous slags were made from ilmenites in the following deposits: Valley County, Idaho; Trail Ridge, Fla.; Aiken, S. C.; and Maclntyre, N. Y.; titaniferous magnetite from Iron Mountain, Wyo., were also evaluated. The tests were made in two chlorinators, a 4-inch and a 36-inch unit. Preliminary testing was done in a 40-millimeter bench-type unit. Chlorine gas was contacted with a loose mixture of titaniferous slag and carbon at a high temperature to form titanium tetrachloride. The moving-bed system used in this work involved a downward movement of feed countercurrent to the chlorine flow, and residues continuously removed from the bottom of the reactor. The performance characteristics of these slags depended on their composition, which varied widely according to the geographic source of the ore. The results showed that all but two of the slags could be chlorinated as effectively as rutile, converting 70 to 80 percent of the titanium to the tetra-, chloride. The two slags that proved difficult were made from New York ilmenite and Wyoming titaniferous magnetite. These slags contained enough magnesium to cause clinkering, which necessitated that the bed be prematurely withdrawn before more than 70 percent of it could react. The iron content of the slags did not interfere with operating the chlorinators. The data from the 4-inch and the 36-inch units were in agreement on the relative amenability of the slags to chlorination.

Jan 1, 1962

By Ernest A. Curth

The Bureau of Mines and Old Ben Coal Co. concluded a cost-sharing contract in 1975, the objective of which was to demonstrate the Herrin No. 6 coalbed in southern Illinois can be mined safely by longwall methods. Under the agreement, three longwall panels are to be mined at Old Ben No. 24 mine. A premining investigation laid the groundwork for specifying a roof-support system designed to control hazardous ground. Old Ben Coal Co. and Bureau engineers selected lemiscate-type roof shields. A rock mechanics program and geological mapping provide early warning capability and criteria for future equipment design. The effect of mining on the surface was monitored by a surface survey to develop subsidence-prediction criteria for the Illinois coal basin. The first of the three longwall panels started up in September 1976 and was completed in May 1977. The major adverse condition was the occurrence of limestone concretions, called coal balls, in massive pods. The shields provided adequate roof control even in faulty ground. Operation of the second panel started on August 1, 1977, following panel-to-panel transfer of the equipment. The accident rate was low.

Jan 1, 1978

By Jack Touseull

On November 15, 1972, the Bautsch mine, a lead-zinc mine in Paleozoic dolomites, experienced a massive rock failure involving 3 to 5 million tons. Because this failure was large and extended to the surface, it was included in the Federal Bureau of Mines investigations on "Massive Rock Failures." Analysis of the rock mechanics and mode of failure revealed that failure at the Bautsch mine was the result of the interrelationship of many factors. Factors related to the failure were found to be external and internal to the mining environment. Unlike internal factors, external factors were not apparent and, therefore, many external factors were investigated; some of which are not normally considered in rock mechanics analyses. External and internal factors determined to be of significant importance were: (1) precipitation, (2) fractures, (3) plastic clay layer, (4) topography, (5) rock alteration, (6) bedding, and (7) mining zone dimensions. Because of the conditions at the mine, failure could have been predicted without extensive instrumentation. Application of basic geologic and engineering principles to the internal and external factors could have predicted failure. Alternately, failure would, in all probability, have been delayed by years if, after 1962, mining had been curtailed in the area of failure.

Jan 1, 1980

By J. E. Fraley

Full-column anchored resin bolts were first used in underground mines in 1972. These bolts appear to improve support in many roof bolt applications, as indicated by the use of about 30 million resin bolts in 1980. In the mid-1970's, Bureau of Mines in-vestigators began looking for a substitute for resin because of its short supply and rapidly increasing price. The investigators selected accelerated gypsum plaster (CaSO. ·1/2H20), which becomes gypsum (CaSO.· 2H20) when mixed with water. Gypsum makes an effective alternate grout material because it hardens quickly, is readily available, and is inexpensive in comparison with other cementitious materials. The Bureau received a patent (U.s. patent 4,096,944) for a system combining water capsules (wax-encapsulated water) with plaster into cartridges resembling resin cartridges. This report presents the results of tests conducted by the Bureau on the plaster, the water capsules, and their combined use in cartridges. The tests were designed to determine how the gypsum-plaster water capsule bolting system performs and what happens in the hole while the bolt is being inserted through the cartridge. The test results indicate that water capsule plaster cartridges are a workable alternative to resin cartridges under normal or dry conditions.

Jan 1, 1987

By David Bendersky

This report covers a technical and economic investigation of old electrical power systems, equipment and practices being used in the metal/non-metal raining industry. The principal sources of information were the MSHA District offices, visits to representa¬tive mines and mills, equipment manufacturers and the literature. A list of 85 mines and mills, submitted by the MSHA Districts as candidates for this study, is given and their characteristics are analysed. The electrical power systems and practices at the 10 mines and 9 mills which were visited are described. The principal areas which do not conform to standard electrical practices are discussed with emphasis on the safety aspects of these practices. The costs to update electrical power systems and practices in metal/non-metal mines and mills are given. The principal findings of the study are summarized and recommendations are submitted.

Jan 1, 1980

By Terry R. Neumann

This document, prepared for the U.S. Bureau of Mines Regional Mineral Assessment Program, presents data pertinent to the mineral resource assessment of the Needles 1° x 2° map quadrangle (excluding the Arizona portion), located in the Mojave Desert southeastern California. The U.S. Bureau of Mines (USBM) mineral survey of the quadrangle, conducted from 1991 to 1993, was done to provide the minerals data necessary to support effective land use planning and resource decision making. To this end, this report (1) inventories historic and current mining activity, (2) inventories identified resources, (3) provides an economic analysis; of identified mineral resources and estimates their feasibility for development, (4) delineates areas of exploration and development potential based on current geological, geochemical, and geophysical information, (5) supplies information on land status, transportation networks, power supplies, water availability, and regulations, and (6) analyzes socio-economic impacts of potential mining. The Needles quadrangle is in the Basin and Range province of the southwestern United Van. The area is underlain by a lithologically and structurally complex Proterozoic crystalline basement of gneiss and granite that is overlain by sparse, scattered outcrops of deformed and metamorphosed Late Proterozoic and Paleozoic sedimentary sequences. Mesozoic granitic plutons, particularly in the western half of the quadrangle, intruded the basement and sedimentary rocks, resulting in metamorphism and deformation responsible for the formation of high-grade gneisses and mylonitic rocks (core complex) in the eastern part of the quadrangle. Voluminous Tertiary volcanism unconformably overlie some older sequences. The structure of the area is dominated by Basin and Range extensional block faulting; in the eastern part of the area, block faulting is accompanied by widespread low-angle detachment faulting associated with core complex development.

Jan 1, 1993

By Verne E. Hooker

Near-surface temperature measurements in two granite quarries show that diurnal temperature variations are significant to a depth of 1 or 2 feet, and annual temperature variations are significant to a depth of at least 25 feet. As a result, ground stress anomalies due to temperature exist near the surface, and their magnitude depends upon the time of day and the time of year. Rock stress and corresponding temperature measurements were made in one granite quarry over a rock temperature range of 33° to 81° F. Measured rock temperatures show good agreement with values predicted from one-dimensional heat flow theory. Calculated and measured stress-temperature coefficients for the two granites in this study are given. Thermally induced stress variations in near-surface rocks tested were as large as 1,690 psi from combined daily and seasonal temperature changes.

Jan 1, 1971

By M. W. Von Bernewitz, W. J. Sharwood

So far as is known , there is no complete bibliography on sampling, therefore , this one should be of value . In it are nearly eleven hundred references , some dating back 30 years , on sampling at mines , mills , smelters , power plants , pumping stations and refineries . For convenience , there are included a few references to methods for sampling such materials as leather belting in mills , salt impregnated soils , and mine waters . All the important technical journals , - including some in foreign countries- and engineering society publications , also mining and metallurgical text - books , have been studied for anything concerning sampling , and while it is not claimed that every important reference has been listed , the bibliography is fairly complete . The arrangement is alphabetical by authors ' names , and the references are numbered serially in the crder that they appear in the bibliography . Anonyous references are listed under the name of the journal in which they appear , and are numbered like the references bearing an author's name . Patents are grouped in their numerical order , without index nu.bers . Under the heading , " U.S. Bureau of Mines Publications " , are listed all publications of the bureau that deal with sampling . While the serial number is omitted , these same references , of course , have serial numbers where they appear in the list arranged alphabetically by authors .

Mar 1, 1922

By N. A. Pace

This is one of a series of papers being published by the Federal Bureau of Mines for the dissemination of information on methods and practices used in the mining and preparation of crushed stone for market requirements. Performance in terms of units of work or tons produced per machine and per operator man-hour are given whenever that information is available. Direct operating costs are useful for comparing different methods, and are, therefore, included if possible. In addition to the factual description of equipment and methods used, it is desirable to discuss the engineering reasons for the choices that have been made. This paper is particularly concerned with the opertions at the Columbia plant of Palmetto Quarries Co. of Columbia, S.C. The plant is about one-half mile east of the Congaree River and adjacent to the southwest corner of the city of Columbia. Rail access is by the Atlantic Coast Line Railroad, and by a spur strack of the Seaboard Airline Railroad.

Jan 1, 1962

By M. G. Zabetakis

This publication contains highlights of a 4-hour lecture and demonstration by the Bureau of Mines on the fire and explosion hazards of flammable liquids and solids, oxidizing materials, corrosive liquids, and compressed gases. The authors first presented this material as part of a 2-week course given to officers and enlisted men at the U.S. Coast Guard's Dangerous-Cargo Handling School, established at Fort Eustis, Va., in 1959. The Bureau was asked to present the lecture and demonstration because of the extensive experience of its researchers in handling certain harardous commodities.

Jan 1, 1961

The National Institute for Occupational Safety and Health (NIOSH), in partnership with stakeholders in the mining and surface drilling industries, con-ducted research to develop engineering control technologies that reduce workplace noise exposure. The result of this research partnership is the development of a partial cab.

Jan 8, 2007

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1956 and 1956 are presented in this publication with a minimum of interpretation and comment because of the numerous tables required to afford detailed comparisons between the 2 years. Corresponding table., for 1955 and 1956 follow in consecutive order under the following general sections: (A) General injury experience: Tables I to II: contain current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury data: Tables 12 to 77: Contain current data on causes of injuries, distribution of injuries by part of body injured, clays of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines. (C) Injury experience, by States: Tables 78 to 87: Contain data on injuries, injury rates, employment, cause of injuries, aid severity rates by States. (D) Major disasters: Table 88: Contains data on major disasters, 1947 -56. A major disaster is defined as a single accident in which, or as the result of which, five or more persons are killed instantly or died at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 89 to 93: Contain data on fatalities and their causes at bituminous-coal and anthracite mines from the earliest records through 1956.

Jan 1, 1960

By L. Bruce McDonald

This Federal Bureau of Mines publication is a statistical analysis of all surface and underground coal mine fires reported in the United States from 1950 to 1977. Accounts of selected nonreportable fires and opinion data gathered via interviews with mine safety directors were separately analyzed. Both reported and nonreportable fires were analyzed by time trends, State, ignition source, burning substance, location in mine, equipment, detection, duration, injuries, fatalities, and successful extinguishing agents. It was found that the majority of all mine fires were electrical in origin. The equipment most frequently involved in underground fires was conveyor belts, and in surface fires, it was crushers and/or breakers. Underground fires occurred most often near the working face. Water and hand-portable extinguishers were the most common methods of extinguishment.

Jan 1, 1980

1. Proposals were submitted to the Western Administrative Center of the US Bureau of Mines, Denver, Colorado on 30th December, 1974 and Contract No J 0255003 was awarded, the effective date being 8th May, 1975. Dames and Moore, Denver, are associated with PD-NCB Consultants in regard to environ-mental problems, surface mining practice and legislation in US. BACKGROUND TO THE STUDY 2. Under the threefold pressures of -increased domestic fossil fuel demand -increased value of domestic energy resources -increased demand for environmental protection and safety

Jan 1, 1976

To provide a faster means to open and close permissible electrical enclosures. Approach: An inspection and repair port with a multiple start thread which provides a permissible joint has been developed and tested. How It Works: The inspection port screw thread has a large pitch, which allows the port cover to be rotated from fully closed 10 fully open, in less than one revolution. See Figure 1. When the cover is screwed back in. it be-gins engagement within one eighth turn because the screw design has eight separate threads. To prevent Its unauthorized opening, the port cover has a bolt guarded by ears which accept a padlock. The threads are designed to tolerate a reasonable amount of grit without binding, although wipe-off cleanness is necessary during reassembly. Enclosures of two different sizes each fitted with the quick-access port, were

Jan 1, 1976

By Joan Weinberg

Real gross national produce (GNP) grew at a seasonally adjusted annual rate of 2.0% in the fourth quarter (table 1). The restrained quarterly growth rate was the slowest in 2 years, and was substantially slower than the 2.5 % rate of the previous quarter. According to the U.S. Department of Commerce, the summer drought reduced the fourth-quarter growth rate by 1.1 percentage points. A growing trade deficit and a reduction in business investment were the key economic factors curtailing growth. The trade deficit widened by $6.8 billion, reflecting both a surge of imports and a slowing of exports. Business investment declined 3.7%, mainly as a result of a slowdown in computer sales. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 3.8% for 1988, the fastest in 4 years, despite the drought. However, on a fourth-quarter-to-fourth-quarter basis, real growth measured 2.7%. Increased exports and business spending for plant and equipment accounted for much of the 1988 GNP growth. Employment continued to grow as the manufacturing sector added 414,000 new workers (table 2). Of these, the primary metals industry added 26,000 workers, and the clay, glass, and stone industry added 10,000. The civilian unemployment rate remained low throughout 1988, fluctuating between 5.3% and 5.4% during the last quarter.

Jan 1, 1989