Search Documents

By Y. Nahmad- Molinari

We present a novel on line inductive sensor for the determination of the quality of the concentrates of iron ores. This device is coupled with a cheap USB Data Acquisition System that makes it versatile enough to simultaneously control up to seven fluxes at a very low cost (< $300 US dollars), and achieves a resolution better than 0.5 % on the determination of the magnetic iron content in the concentrate. A RLC circuit with its inductive element placed surrounding a sample of pure magnetite concentrate is tuned at its resonance frequency, by means of adjusting, the feeding voltage of a voltage-controlled oscillator (VCO) and several samples with mixtures of different contents of silica and magnetite are placed in order to get a calibration curve. After some signal conditioning, a National Instruments USB-DAQ NI-6008, acquires the amplitude of the signal via USB port on a PC using a Lab-View program designed for such purpose, in which the calibration curve is used for on-screen data presentation directly in percent of magnetite content. The implementation of this device for control purposes on line directly placed on the concentrators would allow better efficiency of the process and higher quality of the final concentrate by con-trolling; the rotation speed, the rising or dilution water fluxes or bypasses towards milling recirculation cycles.

Jan 1, 2014

By C. Carrasco

"Over the last 30 years the average grade of mined ore bodies has significantly decreased while the proportion of waste removal has in many cases more than doubled. This has been identified as prime reason of a major increase in energy consumption and decrease in productivity across mining operation. Metal coarse preconcentration of ROM feed grades by size rejects low grade gangue/waste material in the size range of 10-100 mm prior to grinding, typically before primary crushing. This relies on propensity of metal to preferentially deport in the fine size fractions after breakage. Metal preconcentration by size has the potential to increase energy efficiency and therefore improve mining productivity on unit of metal basis. Results of an extensive belt cut sampling campaign conducted at a major Australian Au-Cu mine operation show that for some samples between 90% of Au and 80% of Cu is in 40% of the mass at -50 mm fraction. This indicates that low grade coarse material can be removed from the circuit, doubling feed grade at half of the tonnage and therefore improve energy efficiency per unit metal produced. This response, however presents significant variability in the same order as other processing attributes such as impact hardness and flotation recovery. This has led to development of geometallurgical laboratory tests using blast hole chips and drill core facilitating mapping and population of coarse metal preconcentration signatures in long term resources and short term production models. Preferential Cu deportment by size at drilling scale can be recognised, however scales up factors are required to transform laboratory results to production responses. At 50 % of mass the drilling products underestimate the belt cut responses by 20-30 %. Bulk sampling campaign with blast hole and drill core samples spatially related was also conducted to investigate in more detail the difference between production scale and drilling scale preconcentration responses."

Jan 1, 2014

By L. G. Wang

The stability of foams and froth plays an important role in flotation, in which small amounts of relatively weak non-ionic surfactants (frothers) are used to produce air bubbles and foams. In the present work, factors affecting the stability of the foams produced in the presence of common frothers, such as n-pentanol, n-octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG), have been studied. We used the thin film pressure balance (TFPB) technique of Schelud-ko-Exerowa type to measure the equilibrium film thicknesses. The results were used to determine the contributions from the various surface forces to the disjoining pressures in the thin lamellae (foam) films formed between air bubbles. In addition, we used a model developed by Wang and Yoon (Colloids and Surfaces A: Physicochem. Eng. Aspects, 2006) to calculate the elasticities of the lamellae films at the critical thicknesses at which films rupture. The surface forces and elasticity da-ta were then compared with the foam stabilities in the presence of the various flotation frothers. It was found that foam stabilities are controlled by both film elasticity and surface forces, the relative contributions of which change with frother type and concentration. In general, surface forces play a more important role at relatively low frother concentrations, while elasticity plays a more important role at higher concentrations. At the frother additions usually employed in the mining industry, MIBC relies on surface forces while PPG-400 relies on film elasticity in producing stable foams. The former is capable of dampening the hydrophobic force, which is a major attractive force destabilizing lamellae films, while the latter is capable of reducing surface tensions at low concentrations.

Jan 1, 2014

By B. P. Baruah

A good deposit of high sulphur coals of tertiary origin is existent in North eastern region of India. These coals are known to have indifferent characteristics in comparison to other Indian coals. The general Physico-chemical characteristics are low ash and high volatile matter, calorific value and sulphur content. Sulphur in these coals (70-95% of organic) is mostly affixed to the structure of the coal. Owing to the stringent environmental regulations, the utilization of these coals has severe limitations due to high sulphur content. In the present investigation, sulphur incorporation in to these coals has been discussed along with possible organic sulphur functionalities. The various desulphurization techniques carried out for removing sulphur from these coals have been discussed. Two step oxidative desulphurization processes has been found to be most efficient for organic sulphur removal along with mineral matter and potential toxic elements. Keywords: oxidative desulfurization, potential toxic elements, sulfur incorporation

Sep 1, 2012

By Sergey Ulianov, Arkady Senchenko, Alexey Shvets, Arkady Bakotin

"This paper contains description of research results of technology development for copper recovery from weathered tails of iron processing plant. The predominant host mineral that contains valuable component is chalcopyrite occurring in its free form and in associations with ore and rock-forming minerals. Copper grade is 0.26-0.30%. Emulsion inclusions of chalcopyrite in pyrite and sphalerite were noted. Major problem is low copper recovery (30-35%) by flotation. When studying chalcopyrite in primary concentrate it was determined that the surfaces of many chalcopyrite grains are covered with oxide films which prevented collector attachment onto them. Second issue was deep association of chalcopyrite with pyrite and sphalerite. Sulfidizing reagent addition did not help to reach the required level of copper recovery to concentrate. In the result of research performed the technological flowsheet was developed including preliminary treatment of head material in a special unit aiming at oxide films removal, followed by copper rougher flotation on head size tails, crude concentrate regrinding and a number of cleaner flotation operations. After the treatment of weathered tails according to the flowsheet developed, copper recovery to flotation concentrate became 71.53%, at 23.46% copper grade. The suggested technology allows one to solve the issue with treatment of technology-related copper-containing stockpile material, as well as to include the ores where copper is represented by sulfide minerals covered with oxide films into processing."

Jan 1, 2014

By K. Yoo

Cuprous oxide is one of the oldest antifouling agents and also acts as red pigment in these paints. In printed circuit board manufacturing industries, waste etchant contains a substantial amount of copper ion. In the present study, a process was suggested for recovering cuprous oxides from the waste etchant and optimum conditions were investigated to recover the cuprous oxides. The process consists of two steps: in first step, Cu powder is added into wastewater solution, and cupric ions re-duce into cuprous ions (Cu+Cu2+?2Cu+), where cuprous ions precipitate as cuprous chloride; In second step, cuprous oxide is synthesized by adding NaOH into cuprous chloride solution (2CuCl+2NaOH?Cu2O+NaCl+H2O). Optimum conditions were investigated to recover cuprous oxide in the processes. When copper powder was added into wastewater with copper ions, Cu concentration decreased from 15.6% to 2.6% and ORP decreased from 620 mV to -59.9 mV. This result shows that cupric ions reduced into cuprous ions. XRD data indicated that the precipitate was cuprous chloride powder. Using the cuprous chloride recovered and NaOH solution, cuprous oxide was synthesized. To investigate the optimum condition, various NaOH solutions were added into water with CuCl, and then pH, ORP, Cu concentration, Cu contents in precipitates were analysed. XRD data showed that main component of precipitates was cuprous oxide.

Jan 1, 2014

By S. J. Neethling

"This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another. In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system.s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries.A final interesting result is that all the effects examined affect the process to a similar degree, which implies that none of these variables can be disregarded, either in industry or in further research."

Jan 1, 2003

By Leon Lorenzen, Victor E. Ross, Anton W. Kleingeld

Key to successful innovation, whether at organization, industry or national level, is the alignment and utilization of resources in the most appropriate and efficient way. Innovation needs to be directed strategically, and it needs to be auditable in a systematic and integrated fashion. In the light of these considerations, this paper describes the construction and use of a topographical map of the innovation landscape. The purpose of the map is to provide a holistic view of the key factors that enable innovation (the so-called ’landmarks’), how well they are aligned to support a particular type/nature of innovation in the organization, and to identify possible gaps. The significance (importance) and height (performance) of the landmarks in supporting and enabling innovation within the organization is determined by means of a selfappraisal audit. The topography of the landscape derived thus is subsequently interpreted in terms of the organization’s particular innovation strategy and environmental context. The application of the Innovation Landscape Methodology is illustrated in a number of organizations within the Mining and Minerals Industry of South Africa. Important observations and conclusions regarding the strategic alignment of enabler strengths within these organizations are made.

Jan 1, 2003

By Tiago de Souza, Caroline Gonçalves, Carlos Eduardo de Castro, Everton Dias

The Miraí plant from Votorantim Metais, has two screening stages to the bauxite classification after scrubbagem. The final product has hold the larger size of 0,84 millimeters (20 mesh). There are two sieves Haver & Boecker (model R-TE 3658 x 10972), which have four modules with cut size sieves of 10 mesh (1.70 millimeters) and ¼ inch (6.35 millimeters) on the primary screen, and 20 mesh (0.84 mm) on the secondary screen, all made of polyurethane. The actual configuration was established according to the empirical tests realized that aimed the increase material load on the secondary screening. However, having in mind the screening process improvement and use the fractions smaller than 0,84 mm, which have significant levels of Alumina and low reactive silica, was proposed a new test of change the sieves opening for 6 mesh in the primary screen and 28 mesh for the secondary sieve. The objective of this work was measure the ore alterations on the particle size distribution on the screening steps, increasing the plant weight and ratio recovery before and after the test.

Jan 1, 2014

By Renato S. Costa, Afonso H. Martins, Flávia D. Mendes

"This paper presents some important aspects regarding the ion exchange treatment of an Ni and Co sulphate acidic liquor using chelating resins. Chelating resins possessing iminodiacetic or bis-picolylamine functional groups were compared in terms of nickel and cobalt recovery. The experimental resin with bispicolylamine functionalities (Dowex M4195) was evaluated with respect to Ni and Co uptake, and compared with Rohm &Haas commercial chelating iminodiacetate acid resin. The Rohm & Haas chelating resin, Amberlite IRC 748, with its weakly acidic groups, did not work in acidic solution but exhibited good results at pH 4 and above. The resin that efficiently removed metals from high acidic solutions was the bis-picolylamine resin. Maximum nickel uptake values ranged between 85 g and 112 g Ni per Kg of resin.The experimental part dealt with the working conditions, resin characteristics and the influence upon the resin maximum exchange capacity of the following factors: nickel concentration, temperature, pH and resin-to- solution ratio. Based on the experimental data obtained, it has been proposed a innovative technological treatment."

Jan 1, 2003

By C. A. C. Sequeira, G. N. Anastassakis

Electrochemical processes occur on nano-, micro- and macro- scale in numerous applications such as fuel cells, batteries, hydrogen production, mineral extraction, water treatment, electrotherapy, sensors and many others. In most of these applications, gases evolve either at one or both electrodes due to electrolysis. These gases form bubbles play a crucial role in electrochemical systems. For example, in electrowinning (EW) that is used to extract and refine metals such as Cu, Zn, Ni, Mn, and Cd from their solutions, in most cases the solution is acidic and oxidation of water molecules at the anode is the common counter reaction, which results in the liberation of oxygen bubbles. This generally requires a high overpotential and accounts for a considerable percentage of the energy consumed in metal EW electrolytic cells, apart from producing acid mist that is very corrosive for other cell equipment and building structures. The behaviour of bubbles in electrochemical systems is still a complex challenging topic which requires a better understanding of gas bubbles hydrodynamics and their interactions with electrode surface and bulk liquid, as well as between the bubbles themselves. The objective of the current paper is to briefly review the fundamental hydrodynamics of both gas bubbles on the electrode surface and gas bubbles interaction with the liquid bulk solution. The current work also investigates the impact of gas bubbling and some operating parameters in copper EW, such as current density (100-500 A/m2), temperature (25-75ºC), acidity (50-300 g/L) and a typical chemical mist suppressant (<50 ppm). The results clearly show that both suppressant and temperature reduced the overall surface tension of the solution. Also, chloride concentration and applied current improved electrolyte flow and copper quality at higher current densities. The current paper contributes to the development of mineral processing (specifically to copper hydrometallurgy), as it deals with fundamental hydrodynamics and interactions of gas bubbles that formed during copper EW and play a crucial role in copper electrochemical systems.

Jan 1, 2018

By B. A. Kutlin, S. A. Ropeyko, N. A. Yurlova

"The aim of NPO RIVS research and practice activities is to minimize impact of the mineral processing plants (MPP) on environment by using new concentration methods, high-technology equipment, implementation of engineering solutions directed to reduce emission of polluting substances (PS) into atmosphere, application of low-waste technologies, decrease of water withdrawal from a surface water or groundwater source for process needs. In our studies environmental safety of mineral flotation is provided through technologies using highly selective chemicals, that leads not only to reducing reagent consumption, and production of saleable products of high content of extracted minerals, but also to reducing pollutant emissions, decreasing supply of surfactants (SAA) in natural geosystems, primarily, in ground and surface waters. Decrease of water withdrawal from a surface water or groundwater sources for process needs can be achieved by using closed circuits and waste water treatment for further use in process operations, recycled water conditioning to obtain optimum quality parameters for process operations of concentration. Concentration in water (wet processing), tailings dewatering and semidry and dry (filtration cake) stockpiling in tailing ponds, efficient dust-collecting systems contribute to pollutant emission reduction. Use of mineral wastes – concentration tailings as a source of valued components, facilitates efficient use of natural resources and reduces wastes and its impact on natural ecosystems due to smaller areas of damaged lands during waste products disposal. Process and engineering solutions of NPO RIVS that allow diminishing impact of MPP on natural environment (NE) have been implemented in mining and processing complexes of Russia, Kazakhstan, Ukraine, Kirghizia and Mongolia. Compliance with environmental safety requirements contributes to enhancement of mineral processing and sustainable mineral development.INTRODUCTION Mining and processing complexes have a significant impact on environment as a result of extraction and recovery of mineral resources, landscape changes, waste disposal and, as a consequence, pollution of soils, surface and underground water sources. Therefore, the aim of the operation of the mineral processing enterprises in its research and practical activities is to reduce impact on environment due to new beneficiation technologies, high-technology equipment, implementation of engineering solutions directed to reduce emissions of polluting substances (PS) into atmosphere, use of low-waste technologies, decrease of water withdrawal from a surface water or groundwater source for process needs. Compliance with the requirements of environmental safety encourages advancement of mineral processing technologies and sustainable mineral development. Concentration in water, tailings dewatering and semidry and dry (filtration cake) stockpiling in tailing ponds, efficient dust-collecting systems contribute to pollutant emission reduction. Use of mineral wastes – concentration tailings as a source of valued components, facilitates efficient use of natural resources and minimizes waste formation and its impact on natural ecosystems due to reduction of damaged land areas during waste disposal."

Jan 1, 2018

By Zhang Yuejun, Feng Tianran, Shen Zhengchang, Han Dengfeng

"With continuous mining industry development and dressing plant scale expansion, flotation cell is developed towards to large scale and intelligence. Based on flotation cell scale-up theory and industrial practice, KYF-320 air-forced mechanical flotation cell with effective volume of 320m3 was successfully developed by Beijing General Research Institute of Mining and Metallurgy (BGRIMM) and adopted by China Gold Inner Mongolia Mining Co., Ltd, Luming project of China Railway Resource Group Co., Ltd, and Toromocho project of Chinalco in Peru. In this paper, the structure and technical characteristics of KYF-320 flotation cell are introduced, and the application of that equipment in China Gold Inner Mongolia Mining Co., LTD is demonstrated. The tank of KYF-320 flotation cell is cylinder-shaped, 8200mm in diameter and 7500mm high, with double froth lauders and large inclined angle cone bottom. 16 sets of KYF-320 flotation cells of which the processing capacity is 26,000,000 tons/a, are used in the second phase project of China Gold Inner Mongolia Mining Co., LTD. Their stable running shows the long life of impeller and stator and the power intensity (power consumption divided by effective volume of flotation cell) of KYF-320 flotation cell is only 0.73kW/m3 which is significantly less than that of small scale flotation cells. The industrial production obtains good results that the Cu grade of final concentrate of entire flotation circuit is 22.90% at the recovery of 86.73%, when Cu grade of feed is 0.35%, which indicates that KYF-320 flotation cell has good performance and can be widely used in large scale mine."

Jan 1, 2014

By Carlos Rabanal, Levi Guzmán

"The concern regarding grinding media consumption rates is as old as the invention of the tumbling mill. Over the years many materials and grinding media shapes have been tested. Through all this, steel grinding balls have proved to be the most effective media for comminution in tumbling mills. There have been several approaches to be able to the wear of the ball charge in any given mill, all of them based on limited empirical evidence. The mining industry still utilizes the Bond Abrasion test that was developed in the 1960´s. As shown later in this publication, this approach shows error greater than 60%. More recently, in 2007, Radziszewski from Mc Gill University has proposed a different total grinding media wear model; this model is based on decoupling the effects of the abrasion, corrosion and impact wear mechanisms. Also in 2007, Benavente, at the time with Moly-Cop Peru, presented an empirical model relating both ore properties and operational conditions that would affect the wear performance of the grinding media. For the database referred in this article, Benavente’s model shows an average error of ± 12% which represents a higher degree of improvement in comparison with previous approaches. The current paper presents recent research conducted by Moly-Cop Peru to further improve the capability of the empirical model originally developed by Benavente to estimate grinding media wear rates. The work performed included extensive determinations of the Bond Abrasion Index for different types of ores, collected at industrial grinding applications where the corresponding operational information was made available. The results of the research enabled us to build a more robust and confident model for estimating the grinding media wear rate. The average error of this new model is in the order of ± 9% which is a significant improvement over the models previously described."

Jan 1, 2014

By S. J. Dai

The cadmium and cyanide are main poisonous components in cyanide electroplating cadmium waste water of an electroplating plant in Shenyang. The content of cadmium is about 26 mg/L and the content of cyanide is about 11.782 mg/L in this waste water. The main form of cadmium and cyanide are ions which are Cd2+and CN?. Because the cadmium and cyanide exceeded the standard seriously, the waste water must be disposed before it discharges. The microbiological method of treating heavy metals in wastewater has many advantages. For example, it has a fast adsorption velocity, high processing efficiency, wide range of pH and temperature, few invest, low running cost, no the second pollution and so on. At the same time, the CN? could be degradated by some microbiology. The physical nature, the chemical nature of Bacillus mucilaginosus, the adsorbing condition and adsorbing regular of Bacillus mucilaginosus to cadmium in the wastewater are studied by using Bacillus mucilaginosus as adsorbent removing cadmium from electroplating wastewater. The experimental results show that the adsorbing rate of cadmium is over 92%, under the room temperature(about 25?), stiring revolution in adsorption being 800 r/min for 30 min, pH being 5 , the bacteria being cultured after 5d with the biomass of Bacillus mucilaginosus 40g/L (wet weight). The mechanism in biosorption process of Bacillus mucilaginosus to cadmium is analyzed and discussed by TEM , Zeta potential,and infrared spectroscopy analysis. The results showed, the chemical involving is main adsorbing form, while electrostatic attraction, ions exchange, hydrogen bonding and Van Der Waals force are concerned cooperatively. ?NH2 ?, ?C=O?, ?C=O?NH?CH2, ?CH3, ?OH are main adsorbing groups. At the same time, the floatablity of removing cyanide by Bacillus mucilaginosus is explored.

Jan 1, 2014

By J. Menuge, G. Barker

"Liberation (QEM-SCAN) and surface chemical (time of flight secondary ion mass spectrometry -ToF-SIMS) analyses have been undertaken on plant Pb circuit flotation samples with the aim of defining the factors resulting in sub-optimal recovery. Lead flotation circuit feed, cleaner concentrate and tails samples were examined on a size-by-size basis using QEM-SCAN. Sulfide minerals accounted for approximately one third of the flotation feed with pyrite making up 16 wt.%, followed by sphalerite (13 wt.%) and galena (3 wt.%). Non-sulfide gangue minerals comprised calcium carbonates calcite (26 wt.%), dolomite (14 wt.%) with quartz, feldspars and barite all contributing > 5 wt.%. QEM-SCAN analysis indicated that liberation was not the primary cause of the poor flotation response. Principal component analysis was applied to the ToF-SIMS data derived from five samples (as for QEM-SCAN plus rougher concentrate and tails) to enable identification of correlated surface chemical components. Although a significant range of correlations were observed we focus here on those that show a discernible pattern throughout the float circuit. It was found that for the flotation feed the surface of galena were largely obscured but where Pb was observed there was a strong correlation to surface Fe. For the rougher and cleaner concentrates the galena surfaces were relatively clean with no correlation to Fe for the rougher concentrate and minor correlation in the cleaner concentrate. However, in the rougher and cleaner tails the clear correlation of galena with Fe was again apparent. These results suggest, in combination with prior studies of pyrite morphology, that the principal factor effecting grade is the rapid oxidation of the framboidal pyrite resulting in the contamination of the galena surface with a high loading of hydrophilic oxidised Fe species, thus depressing flotation."

Jan 1, 2014

By M. Muravyov, T. Kondrat’eva, A. Bulaev

Metallurgical treatments of sulfide ores containing copper and zinc are characterized by significant losses of base metals, particularly formation of the flotation tailings and slags during the dressing and pyrometallurgical treatment respectively. In addition, SO2 gas obtained during roasting and converting may be as raw material for sulfuric acid production. A treatment of the industrial metallurgical wastes has been investigated. Two samples of old pyrite tailings from two concentrators that contained 0.36% and 0.26% of copper and 0.23% and 0.22% of zinc were leached with 10% sulfuric acid in the column. Recovery of copper reached 47% and 38% while recovery of zinc was 47% and 41% from the first and second samples, respectively. The pregnant leach solutions contained 15.9 g/l and 10.5 g/l of ferric iron. Ferric iron is the strong oxidant and ferric containing pregnant leach solutions can be used for ferric leaching of different types of raw materials containing sulfide minerals. Therefore, ferric leaching of copper converter slag flotation tailings contained 0.53% of copper and 2.77% of zinc with the first pregnant leach solution was conducted. The effect of various experimental parameters on the leaching dynamics of copper, zinc, and iron under batch conditions was investigated. Under the best conditions (temperature 70oC, pulp density 30%) the recovery of copper and zinc reached 80% and 42%, respectively. Thus, it has been shown that acid leaching of base metals from old pyrite flotation tailings with using of the pregnant leach solution for the ferric leaching of copper converter slag flotation tailings is a prospective technique for the complex treatment of mining and metallurgical wastes. Investigated processes could be introduced into the technological flow-sheet of typical pyrometallurgical plants.

Jan 1, 2014

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Tsuyoshi Hirajima, Keiko Sasaki

"Hydrogen peroxide (H2O2) is frequently used as an oxidizing agent in various applications. It has also been reported to reduce the recovery of sulfide minerals. Moreover, the previous work applied H2O2 aqueous solution in selective flotation of chalcopyrite and molybdenite. However, the oxidation method suffered in pilot scale test due to too long conditioning time. Furthermore, the excessive reagent consumption increased the reagent cost, causing the method not economically feasible. Consequently, further improvement is required to reduce the conditioning time and the reagent consumption. The oxidation performance of H2O2 can be improved by using ferrous iron as catalyst, producing a Fenton’s reagent which is more powerful oxidizer than the H2O2 itself. Therefore, the effect of Fenton’s reagent on the floatability of chalcopyrite and molybdenite was investigated in this study. The flotation test results show that selective flotation of chalcopyrite and molybdenite might be possible at low concentration of H2O2 aqueous solution by adding ferrous iron. Moreover, the conditioning time could be shortened by this improvement. To understand the phenomenon, surface characterization using atomic force microscopy (AFM) along with x-ray photoelectron spectroscopy (XPS) analysis were carried out. The AFM images show that the surface of chalcopyrite was readily covered with mountainous features which alters its hydrophobicity after the oxidation treatment. Meanwhile, the molybdenite surface remained clean and relatively hydrophobic. The XPS results indicate that the mountainous features are various oxidation products (i.e., FeOOH, Fe2(SO4)3, CuO, Cu(OH)2). Possible mechanisms of this phenomenon were proposed in this work.INTRODUCTIONConventionally, copper and molybdenum ores are separated in selective flotation circuits by using copper depressants (i.e., sodium hydrosulfide (NaHS), sodium sulfide (Na2S), and Nokes reagent (P2S5+NaOH)). However, these depressants are usually toxic or hazardous. Therefore, various methods have been developed to replace these toxic and hazardous depressants, for example, by synthesizing new non-toxic or low-toxic depressants or by using various oxidation methods such as sodium hypochlorite in an alkaline medium, manganese dioxide, oxygen, ozone, and plasma pre-treatment (Arbiter and Young 1951; Barzyk et al. 1981; Curtis 1941; Hirajima et al. 2014, 2017). Recent study by Chimonyo et al. (2016) reported the effect of H2O2 on reducing the recoveries of sulfide minerals. Moreover, Hirajima et al. (2017) demonstrated that H2O2 depressed the floatability of chalcopyrite and could deliver a selective separation on copper and molybdenum (Cu-Mo) bulk concentrate in flotation process. However, they reported that this method required a higher concentration of H2O2 and a longer treatment time (4.5 h) to get a comparable result to that of using NaHS as copper depressant. Therefore, further improvements are necessary to reduce the conditioning time and reagent consumption."

Jan 1, 2018

By M. P. Krasteva

The froth flotation process for separation of mineral ores depends on the establishment of care-fully controlled froth. The formation of very stable froth in the flotation circuit is a problem that may occur in many plants, resulting in down-time, low quality and grade of final product and considerable expenses. Froths build up on the top surfaces of thickeners, tanks and flotation cells until they overflow, or until the efficiency of the circuit is impaired. A similar problem exists in Assarel concentrator, Assarel-Medet PLC, Bulgaria. Copper and copper-pyrite ores are dressed in Assarel concentrator. They are characterized with variable and complex mineral and physical composition. During the flotation cycle, resilient and difficult to break-down froth is formed, which subsequently impedes the process of thickening and clear overflow obtaining. Due to this problem continuous sampling in the cycle of thickening was conducted. The mineralogical, chemical composition, particle size distribution and solid phase content of the products were determined. It was established that the solid phase of the froth build up on the top surface of the thickener differs considerably from this one of the thickener underflow. The data clearly indicates that a separation process takes place on the top surface of the thickener ? fine particles of chalcopyrite are concentrated in the froth. The role of chemical reagent addition in the break-down of the flotation froth is investigated in terms of surface chemical phenomena involved in the stabilized froths. Measurements of the coper minerals wettability and surface tension at the air/liquid interface were performed. The surface active agent AERODRI® dewatering aids were laboratory tested. Bench-scale froth collapse tests were conducted. Reagent addition into pulp-froth system promotes and leads to a bubble coalescence, an improvement of the wetting of the mineral particles and a decrease of the surface tension at the air/liquid interface. The results of the laboratory experiments showed that the presence of the surface active agent leads to considerably decrease of the froth stability and the destruction of the deleterious froths build up on the top surface of the thickeners in Assarel concentrator.

Jan 1, 2014

By R. Kobialka

In the article results of experiments over jaws? linings in jaw crushers with different shaping of working surface were presented. Following sets of jaws were under investigation: immobile plain jaw and moving jaw with grooving surface. Grooving jaws have groves with circular, triangular and trapezoid cross section. In order to evaluate efficiency of comminution both the grain composition of product and the content of irregular grains were determined, as well as the size of crushing forces and process efficiency were measured. For the combination: plain jaw with grooved one, a good results were obtained as regards the grain composition of product and the content of irregular grains. Crushing forces were higher at crushing with mixed types of jaws (the one plain, the second grooved), in comparison to crushing with using both grooved jaws. Efficiency of the process was definitely higher for mixed jaws.

Jan 1, 2014