Search Documents

By Bret N. Lingwall, Byron Foster

The problem of reliable extreme event modeling of large diameter piles under enormous structural or kinematic loads has gained more attention in recent years. In particular, the soil response around the foundation and impacts to buried adjacent infrastructure has gained interest. One of the principal shortcomings with analysis of large diameter pile foundations under extreme event lateral loading is the reliance on conventional beam on elastic foundation methods, which do not model the soil field response around the pile. These methods are limited for large displacement problems, and for large diameter piles. However, the fundamental interactions between steel and concrete, and structure to soil are difficult to constrain, especially in large strain problems where the structural elements become inelastic. The non-linear interaction of the structural materials and soil is desirable so that assessment of stress changes in the field and effects on adjacent facilities can be modeled. A numerical modeling methodology that addresses these shortcomings has been developed. This method utilizes the interaction of brittle concrete with discrete steel reinforcing and casing in a robust manner capturing inelastic non-linearity in both soil and structure. This paper presents a comparison study of the method, wherein three different validation studies were made to data from full scale laterally loaded pile testing. INTRODUCTION Extreme event lateral loading of deep foundations comes in many forms including earthquakes, landsliding, tsunamis, hurricanes, surface fault rupture, liquefaction induced lateral spreads and many more. These extreme events induce loads on foundations far greater than service or strength loads. Perhaps the most dangerous extreme event loads are those of large soil displacements such as landslides, lateral spreads, and surface fault rupture, wherein the soil surrounding the foundations can move laterally 100 mm to 3 m! In these extreme event loading scenarios, small diameter foundations are pushed past their limits and many engineers prefer large diameter deep foundations for these situations. These deep foundations of diameter 900 mm or greater may be auger cast in place piles, cast in drilled hole piles, cast in steel shell piles, cased or uncased drilled shafts, bored precast piles, etc. For convenience in this paper, large diameter deep foundations will be referred to as Large Diameter Shafts (LDS). In LDS, steel may or may not used as a shell around the perimeter of the concrete and/or as internal tensile reinforcement. The interaction between brittle concrete and ductile steel within and/or along the perimeter of the LDS is critical to understanding the non-linear inelastic behavior of LDS for problems of large lateral displacements from extreme events.

Jan 1, 2018

My selection of the Australian coal industry as the theme of this Presidential Address arose from the fact that it is one of our most important mineral industries. The industry is presently prospering.M.ore coal, mostly of better quality (except for certarn power-house types), is being produced more cheaply in terms of real money than at any time in the past, and exports overseas are currently at a highlevel.In. spite of this, concern has been expressed in certam quarters about the future of some phases of the industry; for example, there has been some public comment on the selling price of our coking coal to Japan, the possible over-export of our coking coals from New South Wales, the introduction of foreign capital to develop large-scale mining ventures in Queensland, and the proposed export of substantial quantities of coking coal from the same State.Furthermore, proposals for the introduction of atomic power plants into several States well endowed with reserves of coal have given rise to comment, and recently the Department of National Development(1968) warned that insufficient attention is being paid to "orderly development and careful husbanding of the nation's coal.To reach a balanced judgment on whether these views are well founded it is essential to make a broad survey of the present position of the coal industry in the Australian economy. I therefore propose to deal briefly with several aspects, and to comment, in particular, on the important subjects of exploration and research in progress at present on Australian coals.Detailed descriptions of the Australian coalfields are to be found in existing technical publications (e.g.. Andrew, 1965; McLeod, 1965) and the data on coal reserves have been progressively revised as more accurate information has become available. In New South Wales detailed knowledge of the coal reserVes is limited to under 20 per cent of the sur...

Jan 1, 1969

Owing to the increased consumption of sulphuric acid; Australian manufacturers have, from time to time, been seeking for a satisfactory source of sulphur that would make them independent of foreign supplies.Some years ago a considerable amount of acid was obtained from the roasting of Spanish pyrites. This ore, in 1913 or thereabouts, cost 16s. per ton f.o.b. Huelva, and freight to the eastern seaboard of Australia was about 20s. per ton. As the ore contained 48% to 50% of available sulphur, it was costing roughly 9d. or 10d. per unit, and, in addition, the cinder, after roasting, was a product of considerable value to smelters, containing as it did a high percentage of iron suitable for fluxing, and appreciable values in silver and gold.

Jan 1, 1925

By Dean Nichols, Matt Ortel

Explosive accidents in the United States have brought increased attention to emergency operation plans (EOP) at all facilities that manufacture, transport, or store hazardous materials – particularly explosive materials. Explosions are sudden, powerful, and complex events that are difficult to characterize in terms of the thermal, over pressure, and debris effects. Industry, regulatory, and public officials require emergency response planners to not only anticipate the blast effects of an explosion, but also to prepare an appropriate response.

Jan 1, 2016

By Anthony Iannacchione, Christopher Mark

Residents of Maxwell Hill, a suburb of Beckley, West Virginia, reported from January until March of 1988 a series of earth tremors. The tremors rattled dishes, and the noises associated with tremors were sometimes loud enough to wake people at night. These events were puzzling because Beckley is in an area of low seismic activity. Maxwell Hill is located above abandoned coal mines, though no direct subsidence damage to surface structures has been documented. A research program was initiated to determine whether subsurface ground movements associated with the abandoned mines could be responsible for the seismic activity experienced at the surface. A hypothesis is proposed which states that seismic disturbances can be caused by abandoned mine failure when two conditions are met. First, some instability must exist at the mine level. The most likely cause of instability is the failure of pillars of coal that were left for support at the time of mining. Second, subsurface movements can result in significant seismic activity only when the rock above the mine contains at least one very strong and brittle layer that is prone to fail violently through rupture or fault slip movement. Analysis of the data indicates that both hypothesized conditions for mine-related seismicity appear to have been satisfied in the case of Maxwell Hill. It has therefore been concluded that the earth tremors experienced by Maxwell Hill residents probably are related to the abandoned mines. Analysis of the potential magnitude of these events indicates that they are unlikely to cause significant surface danlage. The probability that future events will disturb the residence of Maxwell Hill should be quite low based on the identified mechanism.

By Marc Ruest

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC?s Granger Mine, Meikle Mine, and Getchell Mine. A ?split-pipe? laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

May 1, 2002

By H. Meseck

Dynamic pile test methods to establish the bearing capacity of driven piles were developed in the USA more than 20 years ago. In the Federal Republic of Germany, the first dynamic pile tests were carried out at the end of the 70's. Today dynamic pile tests are successfully used to establish the integrity and bearing capacity of driven and bored piles. The Institute of Foundation Engineering and Soil Mechanics at the Technical University of Braunschweig has developed its own method of measuring and evaluation for the execution of dynamic pile tests. The principles of the dynamic pile tests, the measuring and evaluation plant as well as the experience gained with it in the examination of cast-in-place piles are presented in this contribution.

Jan 1, 2010

By K. Nasrallah

"The Dumont deposit is a large (1,179 Mt proven and probable reserve) low grade (0.27% nickel), nickel sulphide project located in the Abitibi region 25km west of Amos, Quebec. Royal Nickel Corporation acquired the project in 2007 and has since taken the project from a scoping study in 2010 through to completing the feasibility study in July 2013.The Dumont deposit in a nickel deposit with the recoverable nickel contained in three minerals; pentlandite, haezlewoodite and awaruite. The minerals are recovered by a combination of flotation and magnetic separation. Over the course of the studies many flowsheet design decisions and changes were made. This paper outlines an overview of the project, flowsheet design including the comminution circuit, desliming and awaruite recovery. The overall resulting flowsheet that was used for the feasibility study is then presented along with the confirmatory locked cycle testing that showed the feasibility design basis was able to produce the predicted concentrate grade and recovery.IntroductionRoyal Nickel Corporation (RNC) is a mineral resource company headquartered in Toronto, Canada, primarily focused on the exploration, evaluation, development and acquisition of base metal and platinum group metal properties. RNC's principal asset is the Dumont Nickel project (Dumont project) located in the established Abitibi mining camp, 25 km northwest of Amos, Quebec. RNC acquired a 100% interest in the Dumont property in 2007. The mineral claims covering the Dumont deposit are currently held 98% by RNC and 2% by Ressources Québec.The Dumont project is located in the province of Quebec in the municipalities of Launay and Trécesson approximately 25 km by road northwest of the city of Amos, 60 km northeast of the industrial and mining city of Rouyn-Noranda and 70 km northwest of the city of Val d’Or."

Jan 1, 2016

By Ronald F. Balazik

This Bureau of Mines study identifies and examines the costs of Federal, State, and local environmental protection controls on domestic phosphate rock mining, The costs include the expenditures needed to comply with government regulations and the effects that these expenditures and regulations have on supply. The study analyzes costs of environmental impact assessments, air and water quality standards, reclamation laws, potential solid waste controls, and local government restrictions. In addition, an industry survey and the Bureau's Minerals Availability System (MAS) are used to evaluate land management policies that restrict access to phosphate resources, Conclusions drawn from these analyses confirm that (1) domestic phosphate mining has incurred substantial control costs and may be subject to significant new regulatory costs in the next several years, (2) certain environmental controls can discourage mining investment, (3) environmental policies governing land-use controls affect the disposition of sizable phosphate resources, and are key determinants in the development of those resources on the Federal do- main, and (4) environmental costs could diminish the competitiveness of domestic producers.

Jan 1, 1983

By Stuart Brashear, Eddie Colburn

The Birmingham Coal and Coke – Knight Mine is a single seam coal mine in central Alabama. As pit development progressed in 2013, concerns over increasing vibration levels resulted in modifications to the blasting program that inhibited shot size and coal recovery. By January 2014, while still over 1,400 feet (427 m) from the regulatory seismograph, vibration levels climbed above 70% of the mine permit limit, even with triple decking of holes and reduced burden and spacing. At this time the decision was made to commit to the use of signature waveform analysis and precision programmable electronic detonators to minimize vibration and maximize the amount of coal that could be recovered before vibration levels reached permit limits.

Jan 1, 2015

By William A. Beck

This report describes the loading and transportation practices employed at the zinc-lead mines of The Eagle-Picher Co., Jo Daviess County, Ill., and Lafayette County, Wis. The report also gives a brief history of the Illinois-Wisconsin zinc-lead district and the operations of the company in the area. The diesel-powered, rubber-tired loading and haulage equipment is described and illustrated from the operational point of view only, and an analysis is made of the materials-handling system without going into health and safety Factors. The costs per ton of the various components of mechanical loading, underground haulage, underground crushing, and hoisting for fiscal year 1960 are tabulated.

Jan 1, 1964

By Leonardo Flores

"Minera Escondida operates two open pits on a porphyry copper district, southeast of Antofagasta, Chile. During 2005, ore will be delivered exclusively from one pit to two concentrators, while from 2006 both pits will provide ore to these plants. Annual testing programmes on drillhole samples, have allowed for the construction of hardness block models since 2000. These models have delivered two main hardness descriptors, the Bond work index and the SAG power index. These parameters and plant operational specifications have been used as input information to forecast, the expected throughput and ball mill product size (P80) for each block of ore. Two forecasting techniques have been used, an in house model, strongly dependant of bond work index and MinnovEx´s CEET2, dependant of Bond work index and Sag power index and other parameters. Model performance has been evaluated from reconciliating on a monthly basis, the forecasted throughputs against a recalculated plant throughput which accounts for losses in tonnage not caused by ore hardness but instead by unscheduled plant operation problems. The model performance for 2003 was ± 2% yearly and ± 5% quarterly, well within the expected ± 3% and ± 10%. INTRODUCTIONThe Escondida porphyry copper district is located 140 km SE of Antofagasta, Chile at 3150 m.a.s.l, at 24°16’ South latitude and 69°04’ West longitude (figure 1)."

Jan 1, 2005

COUNCIL OF ECONOMICS OF AIME Formerly Mineral Economics Division Established as a Division December 15, 1948 Established as a Council February 26, 1957 Franz R Dykstra, Chairman Paul Schultz, Vice-Chairman A J Phillips, Vice-Chairman Douglas Donald, Vice-Chairman J S Vanick, Contact AIME Director A H Lindley, Jr, Secretary-Treasurer Lehman Brothers 1 William Street New York 4, N Y COUNCIL OF EDUCATION OF AIME Formerly Mineral Industry Education Division Established as a Division January 15, 1932 Established as a Council February 26, 1957 0 Cutler Shepard,Chairman Lysle E Shaffer, Vice-Chairman John C Calhoun, Jr, Past Chairman J C Kinnear, Jr, Contact AIME Director J D Forrester, Secretary-Treasurer College of Mines Univ of Arizona Tucson, Arizona

Jan 1, 1958

Study on the New Flow Sheet and Wastewater Recycling for Xiaoliuguo Copper-Bearing Low-Grade Scheelite Ore

Sep 13, 2010

By K. Lang

A case study is provided that highlights the successful use of high efficiency electrical submersible pumps (ESPs) adapted from the oil and gas industry for a large scale, open pit mine dewatering operation. In this case, the mine is Goldcorp?s Peñasquito Mine, Peñasco and Chile Colorado open pit development areas in Zacatecas, Mexico. At the time of publication (July 2012), there were 18 vertical bedrock dewatering wells producing an average flow rate of 350 liters per second (lps) from the Peñasco and Chile Colorado development areas. Average pumping rate per well was 18 lps, with a maximum of 44 lps. The depth of wells varies from 330 m to 500m, and includes both in-pit and perimeter (ex-pit) pumping centers. A network of 50 piezometers was used to monitor the response of groundwater levels to pumping. Since dewatering operations were initiated in 2007, groundwater elevations decreased overall, from approximately 1950 m above sea level (masl) to around 1625 masl, for a total of 340 m of drawdown. The pit floor elevation was approximately 1655 masl. All of the producing wells were constructed with 16-inch boreholes, completed with 10-inch diameter blank casing and louvered screen sections and equipped with ESPs. The application of ESPs has proven to be highly effective in the case of Peñasquito?s dewatering operations. Noted advantages include the following: ? Small diameter pump allows use of smaller diameter boreholes (16 inches) and casing / screens (10 inches) reducing well drilling and construction costs ? Greater application range for flow rate and total dynamic head ? Variable speed drive systems for greater energy efficiency and flow rate optimization ? Integration of downhole instrumentation into the motor and pump assembly The advantages and benefits of using high efficiency ESPs revolutionized the dewatering program at Peñasquito open pit mine as evidenced by the number of deep vertical well installations and high dewatering flow rates and total dynamic head requirements.

Feb 27, 2013

By Bijan Taheri, Behrouz Maghsodi, Monireh Heshami, Reza Kohan

A common problem recently encountered with the increase in the rate of input feed at Enrichment Plant 2 of the Sarcheshmeh Copper Complex is the loss of value to the tails, translating to lower recoveries. The feasibility of the direct transfer of part of the high-grade concentrate from rougher stages to an appropriate position along the circuit was studied, and two positions were proposed for direct transfer of the concentrate. One position was the feed flow into cleaner cells, and the other was the feed flow into the recleaner cell. The results indicated that transferring the concentrate from the first unit of the rougher stage to the feed flow into the cleaner cells was feasible, with no limitations, while the second position required the installation of a set of hydrocyclones. It was found that the transfer of concentrate to the proposed positions not only addressed the problem of limited cell capacity, resulting in debottlenecking of the circuit, but also improved metallurgical separation efficiency up to 1.4%.

By Julie Shang, Tim Evans, Michael McDonald, Yu Guo, Bingfeng Xue

Effective chemical grouting represents a technical and economic solution to many challenges related to soil stabilization and blocking the flow of water. Chemical grouts are facing increasing demands in durability, environmental impact and value. To better meet these challenges, a novel and cost effective process was developed to produce a sodium silicate that increases the ratio (i.e. silica to alkali) beyond what has been used in traditional silicate-based grouts. The move to a lower sodium form of silicate was anticipated to have two desirable performance enhancements; a reduction in leachable sodium and improvement in the durability of the silicate grout. An in-depth study was performed at the University of Western Ontario Geotechnical Research Centre to quantify improvement in durability as well as other performance properties such as compressive strength. The study began by first modelling the gelation time and reaction kinetics of the high ratio sodium silicate over a range of silicate concentrations using two different setting agents as well as with/without a hardener. As expected, reducing the level of sodium produced a much more water resistant grout. These same formulations also showed a four order magnitude reduction in permeability. Somewhat surprising, test results showed the higher ratio silicate having much higher compressive strength. At the time of this abstract, the high ratio silicate was moving to the trial stage for geotechnical applications while the petroleum industry was further along with several successful field trials for water blocking as well as cement remediation. This paper will review the chemistry, testing and features of this next generation form of sodium silicate. Introduction Sodium silicate based grouts have been used for decades for soil stabilization and water control. Over the years, several silicate-based systems have been tailored for specific application conditions to maximize performance and reduce cost. Past research has also focused on the selection of setting agents and hardeners for silicate grouts. A constant in the development effort has been the grade of sodium silicate. The vast majority of chemical grouts have been formulated using a ~3.2 ratio sodium silicate. As a very brief overview on the meaning of “ratio” and why it is so important to performance properties. The ratio describes the proportion of sand to alkali or SiO2:Na2O used to make different grades of sodium silicate. Comparing a 2.2 ratio to a 3.2 ratio, it is easier to polymerize and set the 3.2 ratio. Upon setting and forming a silica gel, the system has higher compressive strength values and improved durability with a reduced level of syneresis (i.e. shrinkage). This leads to the question if 3.2 is better than 2.2 why not go to 4.2 or higher?

Jan 1, 2018

By D. C. Peck, H. D. M. Cameron, N. M. Halden, L. S. Jobin-Bevans

Abstract-The late Archean Pipestone Lake anorthosite complex (PLAC) is a 0.9 x 17 km sill-like layered intrusion that is part of a suite of coeval megacrystic anorthosite bodies in the Cross Lake region, northwestern Superior Province. Exploration for Ti-V-Fe oxide mineralization and concurrent geological investigations have contributed to a greater understanding of the lithostratigraphy of the PLAC and its oxide mineralization. Mapping and drill core studies have established a laterally continuous igneous stratigraphy comprising six leucogabbro/anorthosite zones and three melagabbro/gabbro zones. Field evidence, including disrupted blocks of layered units, scour contacts, and size-graded and modally-graded layering, suggests younging towards both the northern and the central parts of the complex. A decrease in the anorthite content of the feldspars from An75 in the south to An30 in the north suggests that the magmas become more evolved to the north. Macrorhythmic layering and gross morphological features suggest that the PLAC crystallized from four major influxes of geochemically similar basaltic magmas. The paucity of magmatic erosional features in the PLAC indicates that layering developed in a relatively static magma chamber, so that in-situ crystallization processes are required to account for the observed petrologic diversity. Drilling has confirmed that a significant Ti- V-Fe resource is contained in two of the four discrete mineralized subzones in the PLAC. Textural evidence and the stratiform nature of the oxide-enriched subzones are consistent with a magmatic origin for the oxide mineralization.

Jan 1, 1997

By L. D. Patts, J. D. Noll, S. E. Mischler, G. H. Schnakenberg

In this study, we evaluated the ambient diesel particulate matter (DPM) concentrations (at the intakes and exhausts of the mine) as the entire vehicle fleet of a stone mine switched from using 35% biodiesel to using a water emulsified fuel (PuriNOx). Elemental carbon (EC) was reduced by 45% when a PuriNOx blend containing 10% water replaced 35% biodiesel and by 57% when a PuriNOx blend containing 20% water was used. Other factors such as engine duty cycle and production changes could potentially cause some day-to-day EC fluctuations, and no direct comparison to commonly used dieselfuels (No. 1 or No. 2) was achieved. Therefore, a second study was performed in a controlled “isolatedzone” environment to fametal mine, comparing PuriNOxto No.1 diesel fuel in a load haul dump vehicle. The EC fraction of the DPM was reduced by about 71% when the PuriNOx blend containing 10% water was used and by about 85% when the PuriNOx blend containing 20% water was employed. This study did not determine how the water emulsified fuel would affect the engine or power.

By H. Warren Newcomen

The southwest wall of the Lornex Pit at the Highland Valley Copper mine has been experiencing slope displacements since 1978. Measures to manage the displacements on previous pushbacks have included stepping out, scheduling pushbacks to unload the crest of unstable areas, slope dewatering and mining with intensive slope monitoring. The final pushback on this wall is currently being mined and substantial modifications to the slope geometry could prove to be uneconomic. As a result, a campaign of surface water collection and diversion, horizontal drainhole drilling and deep well drilling is currently underway to maintain an acceptable degree of stability to the end of mine life. The various factors contributing to instability, including engineering geologic controls, rock mass strength, and surface and groundwater hydrology are presented. Movement trends, displacement magnitudes and stability analyses results are also discussed.

May 1, 2002