Search Documents

By Chikabumi Yamauchi, Mitsuru Tanahashi, Tsuyoshi Taniguchi, Nobuo Furuta, Toshiharu Fujisawa

"It is essential to clarify the equilibrium relations among nonmetallic inclusions of the Mn0-SiO2-CrOx system and molten stainless steel in order to control non-metallic inclusions formed by the deoxidation of stainless steel with silicon. In the present study, the phase equilibria of the MnO-SiO2-CrOx system were measured by conducting the following experiments under controlled oxygen partial pressure, Po2, at 1873 K:1) Phase equilibria of the MnO-Cr20 3 binary system were measured for Po2 = 2 x 10-6 ~2 x 102 Pa.2) Phase equilibria of the MnO-SiO2-CrOx ternary system were measured for Po2 = 2 X 10-6 Pa.Based on the results, the phase diagram of this ternary system was established under the condition of the Si-deoxidation process of stainless steel (Po2 = 2 x 10-6 Pa and T = 1873 K).IntroductionAt the deoxidation stage in steelmaking process, generally multiple deoxidizers participate in deoxidation reactions, and the composition of deoxidation products ""non-metallic inclusions"" greatly varies depending on deoxidizing efoments and their contents. In order to control non-metallic inclusions formed by the refining process of steel, it is essential to clarify the equilibrium relations among non-metallic inclusions and molten steel.Especially, during the refining process of stainless steel, nonmetallic inclusions in molten steel seem to- change as follows. After the oxidation refining, Mn-chromite is formed in molten steel as non-metallic inclusion. By the deoxidation with silicon addition (mainly less than 1 mass%), Mn-chromite inclusions are changed their compositions to Mn-silicate. Segawa et al.[l] have reported the effect of amount of silicon addition on composition and mass ratio· of non-metallic inclusions during the Sideoxidation process of 18Cr-8Ni stainless steel at 1873 K, as shown in Figuri; L At higher silicon content than 0.5 mass%, only Mn-silicate was identified as non-metallic inclusion. On the other hand, at lower silicon content, both of Mn-chromite (MnO Cr2O 3) and Mn-silicate were identified. However, the thermodynamic and the kinetic analyses of the above-mentioned Sicdeoxidation process have not been made due to lack in the thermodynamic data for the non-metallic inclusions· of the MnO-SiO2-CrOx system, such as the phase diagrams, the activities of the components, and the free energy of intermediate compounds. In relation to the phase diagram of this system, those of the MnO-SiO2 [2] and the SiO2-Cr2O 3 [3] binary systems have been only reported"

Jan 1, 2000

By Satian Niltawach

Iron sulphate jarosite through which iron in zinc sulphide concentrate feed is removed from the production circuit of conventional roast-leach-electrowin process, is chemically unstable and environmentally hazardous even if it is mixed with lime. If zinc silicate ore is used at similar chemical conditions in place of calcine in the jarosite precipitation, the resultant silico-jarosite residue having been mixed with lime is chemically stable and environmentally friendly. The recovery of zinc from silicate ore is also higher than that from calcine.

Jan 1, 1994

By Shigem Kuramoto

Pure copper is known to exhibit intermediate temperature embrittlement when it is deformed at a slow strain rate, and a small addition of zinc suppresses this embrittlement. In the present study, the relation between zinc addition and hydrogen behavior was taken into account since the impurity hydrogen is believed to deteriorate the ductility at intermediate temperatures. Pure copper and Cu-l mass % Zn alloy specimens are prepared by melting in argon and in vacuum, so that a comparison can be made between the specimens with normal hydrogen content and those with' less hydrogen content. Tensile tests are performed at temperatures ranging from room temperature to 600 "C, and hydrogen behavior is analyzed using a newly developed testing machine that can detect gas evolution from the specimens during deformation and fracture in ultra high vacuum. The small addition of zinc to pure copper decreases hydrogen content, leading to the improved ductility at intermediate temperatures. In addition, the samples of both pure copper and Cu-1%Zn melted in vacuum exhibited higher ductility at intermediate temperatures than those melted in argon atmosphere, which is attributed to reduced hydrogen content.

Jan 1, 1998

By Seung-Chul Lee

Transparent conducting tin(1V) oxide thin films have been studies and developed for the electrode materials of solar cell substrate. Fabrication of tin oxide thin films by sol-gel method is process development of lower cost photovoltaic solar cell system. The research is focused on the establishment of process condition and development of precursor. The precursor solution was made of tin isopropoxide dissolved in isopropyl alcohol. The hydrolysis rate was controlled by addition of triethanolamine. Dip and spin coating technique were applied to coat tin oxide on borosilicate glass. The resistivity of the thin film was lower than 0.18-cm and the transmittance is higher than 90% in a visible range.

Jan 1, 1999

By C. A. Summers

The U.S. Bureau of Mines applied process mineralogy to investigate a lead and zinc deposit located near Story Creek, Colville Mining District, Alaska. Mineralization is hosted by the Kayak Shale in veins, veinlets, and breccia. Sphalerite and galena, with supergene anglesite, occur in symmetrical quartz veins and between breccia clasts. The study sample analyzed 2.11 percent Pb, 5.37 percent Zn, 0.014 percent Cu, and 1.2 oz/ton Ag. Analyses of crushed products showed that 33 percent of the sample weight, and more than 50 percent of the Pb and 65 percent of the Zn, are in the minus 850 um fraction. Liberated grains of sphalerite and galena were found in crushed products finer than 300 um. Beneficiation tests indicate the material is amenable to processing by traditional gravity and flotation techniques.

Jan 1, 1991

By Paulo von Krüger

This paper deals with the cell design and operation of a tin electrorefining 1:5 pilot plant. The purpose of the work was the fitting of the basic parameters to be used in a full-scale tankhouse from a major Brazilian tin producer. The main specific difference was the use of permanent stainless steel cathodes instead of conventional tin starting sheets. The results of both product quality and operating parameters are discussed.

Jan 1, 2003

By J. Shibata

The recovery process of valuable metals, such as Ll, Mn, Ni and Cr from a waste lithium battery was developed n this study. Lithium and Mn are selectively leached from the battery by using dilute mineral acid. Main part of the battery comprises stainless steel, and Fe, Ni and Cr are easily leached by the mixture of dilute HCl and HNO3 Lithium and Mn are precipitated as metal carbonates from the? individual leached solution with sodium carbonate solution. The solution containing Fe,Ni and Cr Is treated by solvent extraction to separate NI and Cr from the leached solution. The experiments are carried out for leaching and separation steps. According to the experimental results, the flow. sheet for a recovery process of valuable metals from a waste lithium battery has been established.

Jan 1, 1995

By Philippe Charlier

Recycling of aluminium contained in used aseptic beverage cartons is a difficult task which has nevertheless to be tackled by our modern societies. Techniques have earlier been developed by the paper and pulp industry for the recycling of the board fibres from collected post-consumer beverage cartons. A joint technical feasibility study by Granges and a leading beverage carton producer has dealt with different techniques for handling residues from repulping facilities. The aluminium obtained can be used as raw material for the production of thin gauge foil, thus closing the recycling loop.

Jan 1, 1995

By Susumu Okabe

Top blowing lances are employed by the Mitsubishi Continuous Copper Converter for the continuous supply Of reaction gases into moken bath. In order to minimize the refractory wear caused by the interaction between the furnace lining and the melt splash. optimum furnace design and blowing condition are? required. An empirical equation obtained by the physical model study enables the estimation of the splashing rate on a vel1ical plane at a certain distance from the lance.

Jan 1, 1996

By Yang Wang, Xiancong Zhao, Hao Bai, Qi Shi, Zhancheng Guo

Linz-Donawitz converter gas (LDG) or basic oxygen steelmaking gas (BOSG) is one of the most important secondary energy sources in iron and steel industry, whose effective use plays a vital role in energy saving and emission reduction. However, the generation of LDG suffers from great fluctuation with respect to the production status of steel making. Therefore, a long term prediction model of LDG generation would be essential in gas system balancing and optimization. In this paper, a long term prediction model for the generation volume of LDG was proposed based on the steelmaking production estimation from Gantt chart and k-means clustering algorithm. Compared with the previous model, this model considered the influence of different steel type on LDG generation. The experimental results of a steel plant demonstrate that the proposed model exhibits high accuracy and can provide an effective guidance for balancing and scheduling of byproduct gases.

Jan 1, 2016

By Wolfgang Baum

Case studies from epithermal gold-silver deposits in the western United States and in Latin America show that the routine use of process-related mineralogical studies has become an important tool for the reduction of development, capital and operating costs. Bypassing the mineralogical characteristics of epithermal gold-silver ores, as a result of fast-track development approaches, has resulted in multimillion dollar metal losses and/or in considerable modification costs of existing operations.

Jan 1, 1988

By Jinrong Zhang

Fresh cyanide solution was treated by near UV light with the assistance of photocatalysts. Cyanide was oxidized mainly to cyanate. Photochemical behavior of the anatase and rutile forms of TiO2 was compared. It is found that anatase has a much higher activity than that of rutile. Bubbling of oxygen in the reactor showed no appreciable increase in cyanide oxidation, implying that the reaction is surface controlling. A very interesting finding in this study is that a natural mineral, ilmenite, can replace chemical titanium dioxide as the photocatalyst. Ilmenite without any treatment did not catalyze the oxidation of cyanide. But, after being roasted at high temperature with oxygen, the oxidation was enhanced dramatically. The mechanisms of photooxidation of cyanide and the roasting of ilmenite are proposed.

Jan 1, 1991

By P. K. Jimack, C. E. Goodyer, A. M. Mullis, P. C. Bollada

"We review the application of advanced numerical techniques such as adaptive mesh refmement, implicit time-stepping, multigrid solvers and massively parallel implementations as a route to obtaining solutions to the 3-dimensional phase-field problem with a domain size and interface resolution previously possible only in 2-dimensions. Using such techniques it is shown that such models are tractable even as the interface width approaches the solute capillary length.IntroductionMulti-scale modelling impinges upon many areas of science, engineering and technology where the interplay between processes occurring on disparate length and/or timescales can affect the properties of systems in a complex, and sometimes unforeseen, manner. One such is the processing of materials where interactions at the atomic scale, through the nano- and microstructural scale can have a profound affect on the macro-scale response of engineering components. Here we focus on one such problem, the crystallisation of alloy melts, to illustrate how a range of advanced numerical techniques make the modelling of such systems tractable.The modelling of solidification structures, in particular the growth of dendritic crystals, is a subject of intense and enduring interest within the scientific community, both because dendrites are a prime example of spontaneous pattern formation and they have a pervasive influence on the engineering properties of metals. For alloy systems, which form the vast majority of engineering materials, solidification involves the rejection of both solute and latent heat from the growing solid, forming a coupled diffusion problem in which both the chemical and thermal diffusion equations should be solved. The multi-scale nature of this problem arises from the disparity between the thermal and solutal diffusivities for most liquid metals, which are typically 10-5 m2 s-1 and 10-9 m2 s-1 respectively. The ratio of these two, referred to as the Lewis number (Le =Dia), is therefore typically of the order 10,000 and gives a measure of the multi-scale nature of the problem. In fact, in many cases the thermal diffusivity is so much larger than its solutal counterpart that thermal diffusion is considered instantaneous, wherein the system can be approximated as isothermal such that the multi-scale calculation does not need to be performed. This is certainly a reasonable approach in most conventional castings. However, there is a class of solidification problem in which this approach is far from satisfactory, namely Rapid Solidification (RS). The application of isothermal phase-field models in such situations are highly likely to produce spurious results or to fail totally, particularly for temperatures below To (the temperature at which the free energies of the solid and liquid phases are equal at the concentration of the bulk alloy), wherein partitionless solidification may occur."

Jan 1, 2013

"An experimental study has been performed to investigate the dispersed phase holdup induced by a high-strength submerged gas injection in a bottom blown air-stirred one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor using two different tuyere configurations. The air flow rates varied from 0.00599 m3/sec to 0.01312 m3/sec. In these series of experiments, water height and kerosene height were kept constant at 0.23m and 0.02m respectively. The dispersed phase holdup was determined at various gas flow rates, and tuyere orientations by using water and kerosene.The dispersed phase holdup increased with gas injection rate and decreased with vertical distance from the original interface. At constant gas flow rate, as the vertical distance increased in the centerline, off-center configuration of nozzles displayed higher values of the dispersed phase holdup than those of the center configuration. The variation of the dispersed phase holdup with the dimensionless axial distance and the gas injection rate was correlated by using the Modified Froude Number. The experimental values of the dispersed phase holdup were found to be in good agreement with the calculated values obtained from the correlation equations."

Jan 1, 1999

By John L. Watson

Many metals-based industrial processes experience limitations in their operations due to an inability to effectively separate solids and liquids where partidesizes are less than 25 microns. Steel plant sludges ,generated, from the cleaning of furnace off-gases represent a typical example of processing difficulties attributable to material characteristics, and recycling or even efficient disposal of these materials is often a major problem. The use of a magnetic field to augment the traditional mechanisms of vacuum dewatering has, been demonstrated in previous work to have significant value in separating solids and 'liquids, where the solids exhibit some magnetic character. Magnetic vacuum dewatering has been used with magnetite ores and with blast furnace sludges and magnetic fields have been incorporated successfully in drum and disk vacuum filters. The research described in this paper investigates the use of magnetic seed material and flocculants to extend the application of magnetic, vacuum filtration to non-magnetic pulps. It is shown that the addition of a flocculant can enhance the capacity of drum and disk magnetic fIlters when treating materials, such as steelmaking sludges, which are only partially magnetic. In addition, the use of seed magnetite with a flocculant is shown to improve the dewatering of fine hematite pulps in a drum magnetic filter. However the use of a flocculant and seed magnetite had only limited success in improving filtration in a disk magnetic filter with a fine quartz pulp. A disadvantage of magnetic vacuum filtration with seeding appears to bean increase in cake moisture due to water entrapment in the floes resulting from agglomeration and magnetic attraction.

Jan 1, 1999

By W. B. Carter, A. T. Hunt, G. W. Book

"Combustion Chemical Vapor Deposition (CCVDSM ), an open air, flame assisted CVD process, is under development. The CCVD process produces non-line-of-sight, epitaxial deposition. Materials deposited include YBa2Cu3Ox' Y2BaCuOx, BaTiO3, Y2FesOI2, ZrO2, yttria stabilized ZrO2 (YSZ), partially (yttria) stabilized ZrO2 (PSZ), and amorphous silica. Two modifications of the CCVD process are being studied. Liquid fuel CCVD deposition, involves the combustion of an organic solvent that contains dissolved reagents carrying the desired coating cations. Gaseous fuel CCVD deposition uses a flammable gas as fuel. A non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol prior to its combustion. Substrates to be coated are held near the flames' ends.IntroductionThin films and coatings can be deposited using a wide variety of techniques including chemical vapor deposition (CVD). CVD is ""a materials synthesis process whereby constituents of the vapor phase react chemically near or on a substrate surface to form a solid product.""lIn conventional CVD processing, gases carrying coating constituents flow into a reaction vessel where deposition occurs onto a heated substrate. The deposition process is often conducted at reduced pressure. Both cold and hot wall reaction chambers are used. Heat can be provided by a resistance furnace, rf induction, or high-intensity radiation lamps. Plasma, microwave, photo, laser, RF, and electron-enhanced CVD processes have been developed. The necessity of using a reaction vessel limits the substrate size and affects coating economics. Although most CVD depositions are performed as batch processes, continuous deposition can be accomplished with the use of appropriate hardware.The chemical vapor deposition of thin, dense oxide films has been accomplished in the open atmosphere with a flame assisted process. The process is called combustion chemical vapor deposition (CCVDSM).2 Two modifications of the CCVD process have been developed. The liquid fuel CCVD process involves the combustion of an organic solvent in which reagents (containing the coating cations) are dissolved. The gaseous fuel CCVD process uses a flammable gas as fuel. In this modification, a non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol of small droplets prior to its combustion. Substrates to be coated are held near the flames' ends."

Jan 1, 1994

By A. D. Neuman, C. C. Davis, M. R. Lopez, A. C. Martinez, T. A. Nothwang, S. L. Voit

"One of the thrust areas for the Global Nuclear Energy Partnership (GNEP) program is the development of actinide bearing fuels for transmutation in a fast reactor. Mixed Oxide (MOX) fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition from which minor actinides (MA) can be incorporated for use as a transmutation fuel. This study involves characterization of precursor powders and pellets to be inserted into the Advanced Test Reactor in Idaho. These pellets will have three compositions: one standard MOX composition, (U80Pu20)O1.98, and two compositions of MA-MOX with oxygen to metal ratios (O/M) of (U75Pu20Am3Np2)O1.98 and (U75Pu20Am3Np2)O1.95. The precursor powders, which consisted of, highly enriched uranium oxide, HEUO2, depleted uranium oxide, DUO2, neptunium oxide, NpO2, americium oxide, AmO2, and plutonium oxide, PuO2, were characterized using a field emission gun scanning electron microscope (FEG-SEM) for particle morphology, size, and size distribution prior to pellet production.IntroductionThe Global Nuclear Energy Partnership (GNEP) was created in order for “fuel-cycle supplier” nations to provide assured supplies of nuclear fuel to “fuel-cycle customer” nations. The customer nations would utilize the fuel for electricity generation and subsequently return it to the supplier nation after it is spent. This spent fuel would then be reprocessed by the supplier nation in order to recycle the actinide constituents, mainly uranium and plutonium, in advanced nuclear power reactors, and thus reducing waste volumes [1, 2]. Nuclear materials would also be strictly controlled through the International Atomic Energy Agency. One of the thrust areas for the GNEP program is the development of these actinide bearing fuels for transmutation in a fast reactor under the U.S. Advanced Fuel Cycle Initiative (AFCI) in order to transmute long-lived transuranic actinide isotopes into shorter-lived fission products [3]."

Jan 1, 2008

By June-Yong Eom, Jong-Jin Pak, Jung-Mock Jang, Min-Kyu Paek

The nitrogen solubility in liquid Mn-Si, Mn-Si-Fe, Mn-Si-C and Mn-Si-Fe-C alloys has been measured by the gas-liquid metal equilibration technique in the temperature range of 1673-1773 K. The additions of silicon, iron and carbon significantly decreased the nitrogen solubility in liquid manganese alloys. The experimental results were thermodynamically analyzed by the Wagner’s formalism to determine the first- and second-order interaction parameters of silicon, iron and carbon on nitrogen in liquid manganese. The thermodynamic parameters can be used to predict the nitrogen solubility in ferromanganese and silicomanganese alloy melts as functions of the melt composition and temperature at given nitrogen partial pressures.

Jan 1, 2014

By Wan Pu

Chrysotile asbestos samples from different mines have been studied by SEM and TEM, including high resolution electron microscopy, to find reasons for differences in physical properties of different types of asbestos fibres. The results show that the inner diameters of fibre tubes and the lattice images of fibres are different for soft and hard asbestos fibres. These differences are related to temperatures and geochemical conditions during the growth of chrysotile asbestos.

Jan 1, 1989

By G. White

Traditional atmospheres used for Aluminum annealing have been air, exothermic gas, and cryogenic purity Nitrogen. Air and exothermic gas have several problems associated with them such as surface discoloration, toxic emissions, and explosion hazards. High Oxygen levels can cause Magnesium streaking and oil staining, and therefore pure Nitrogen has been the atmosphere of choice for high quality Aluminum coils. A comparative study was made on key Aluminum alloys annealed in Nitrogen with different Oxygen concentrations to determine the effect on surface quality. The atmosphere composition inside the furnace was analyzed during the purge and heat cycle to determine its effects on purge times and exhaust emissions. The Aluminum coils after annealing were visually inspected for surface staining before and after rolling. The lab study revealed that Nitrogen with up to 1.0% Oxygen is acceptable, and did not adversely effects the surface quality or any of the other processing variables. However it isbelieved that higher Oxygen concentrations are acceptable depending on the rolling oils and alloy systems.

Jan 1, 1996