Search Documents

By M. A. Barakat

Large amounts of zinc ash and flue dust containing more than 80 % zinc are accumulated during galvanization processes at the surface of molten zinc bath and in the chimney respectively. Pyrometallurgical recovery of zinc from both of the ash and dust samples has been carried out. The ash was sieved with the help of an industrial sieve shaker provided with mesh sieve having a pore size 0.9 mm. The oversize fraction cut (+ 0.9 mm) was melted at 550 °C under ambient conditions. The produced ingot (1) was analyzed whereas the coarse fraction of the produced slag (+ 0.9 mm) was treated as the coarse ash or added to it. The dust was enriched with suitable fluxing salt prior to heat treatment at 600 °C for 1 h. The produced ingot (2) was analyzed whereas the resulting slag was mixed with the fines of the ash and treated by hydrometallurgical processing to prepare valuable salts of zinc. Parameters affecting recovery processes such as time, temperature and flux percentage were studied. Results obtained revealed that the two prepared ingots (1&2) were successfully recovered with recovery efficiency amounts to =85 %. The obtained samples meet the standard specifications with relatively low price. Also in the light of the strict environmental regulations of pollution control, reuse of these wastes materials will help in keeping the environment clean.

Jan 1, 2000

By Patrick R. Taylor

Thermal plasma technology has a wide range of applications in extractive and process metallurgy. Beneficiation of complex ores, oxide reduction, melting/remelting of refractory metals and scrap, and the recovery of precious metals from waste products are some examples of potential uses for plasma technology. The highly concentrated enthalpy provided by plasma torches is a cleaner energy source and may give higher processing rates per reactor volume than conventional technologies. Some of the other advantages may be: controlled furnace atmosphere, ability to treat fine feed materials and rapid quenching. A review of some of the uses for plasma processing in non-ferrous process and extractive metallurgy is presented.

Jan 1, 1993

By William Petruk

An investigation was conducted to determine types of particles that tend to be recovered in concentrates by mineral beneficiation. It was found that, in concentrates of the same grade the proportion of desired mineral occurring as apparently liberated grains varies widely. In contrast the proportion is nearly constant when the grains considered are apparently liberated grains plus unliberated grains in particles composed largely of the desired mineral. It was also found that the types of particles which tend to be recovered in concentrates are dependent upon the concentrate grade. Hence it is much more important to determine the characteristics of recoverable particles and to measure the percentage of mineral that occurs in recoverable particles. than to measure the percentage of totally liberated mineral. A relationship between concentrate grade and type of particle that tends to be recovered in concentrates was established.

Jan 1, 1989

By Marilda Macagnan, Rosana de Cassia de Souza Schneider, Valeriano Corbellini, Tiago Bjerk, Mariela de Souza Vieira

The great potential of Brazil for the agricultural production makes our country a generator of agro industrial residues. In this context, the solid-state fermentation appears as a technology that shows alternative ways for those residues, adding values to these raw materials, through the production of substances of industrial interest, besides reducing the possible environmental problems. The main objective of this study was to apply the bovine fat residue associated to the garden grass for the fungal lipase production. Initially, 75 microbial cultures were isolated from garden grass samples after incubation of the mixture with bovine fat. From these cultures were selected the filamentous fungi, whose lipase production abilities were evaluated. The isolation and the selection were accomplished by using a differential culture medium containing Tween 80 as inducer substrate of lipase production. The colonies with lipolytic potential were detected by the presence of white precipitation haloes on the agar. With agro industrial residues the best lipase producer fungus was identified as Penicillium sp in 6 days of solid state fermentation. The crude enzyme obtained was tested in transesterification process for the biodiesel production.

Jan 1, 2008

By R. P. King

The linear intercept distributions provide unambiguous and accurate characterizations of the texture of mineralogical materials. The relation between the measured linear intercept distributions and the spatial correlation function is shown to be given by: in the Laplace Transform domain. The linear intercept distributions of the two phases in a low- grade chromite-serpentinite ore were measured. and the spatial correlation functions for both phases were evaluated using the above relation. The correlation functions are the primary relations for integral geometric models of mineralogical texture and this work demonstrates the relation between the 10 stereological model and the 3D integral geometry model for mineral liberation.

Jan 1, 1991

By Lztok Peruš, Goran Kugler, Matevz Fazarinc, Milan Tercel

"Hot deformability of M42 tool steel additionally alloyed with cobalt and molybdenum was investigated. Hot-compression tests were carried out in the temperature range 850 °C -1200 °C, at strain rates range 0.001--6s-l up to strain of0.9. Field-emission scanning electron microscope and optical microscopy were used for characterization of microstructure of deformed samples, which revealed a very complex precipitation of carbides that strongly depends on the soaking temperature, the soaking time, the stress state, the deformation temperature as well as on the strain rate. Gathered data was used to calculate the processing parameters such as process maps, apparent activation energies and strain hardening exponents. For better understanding of thermodynamical properties of the studied steel a simultaneous thermal analysis was conducted. Furthermore the analysis of phase equilibrium was calculated using Thermo-Cale software. On the basis of these studies the optimal soaking temperature and process windows were determined.IntroductionHot workability ofledeburitic tool steels is important economic factor. This means that for each tool steel individuallysafe range of hot working parameters should be revealed. Publications in the literature with regard to the hot workability of tool steels are rare and therefore more information from this research area is desired.The relatively low hot workability of ledeburitic tool steels, i.e. steels in which the solidification is completed by a eutectic transformation of the residual interdendritic liquid to austenite and various alloy carbides (ledeburitic carbides), is usually characterized by the production of surface and internal cracks during the hot deformation."

Jan 1, 2013

By F. Qian

An impinging gas jet on a liquid surface is found in many industrial process systems such as electric arc furnace, welding, steel-making operation and others. Fundamental understanding of the interaction of a gas jet on a liquid pool can provide important insights into process behavior resulting in improved efficiency. A numerical model is developed for solving the flow fields of both impinging gas jet region and liquid pool below, in which the deformed interface shape is predicted simultaneously. Using curvilinear coordinates, the Navier-Stokes equations of each phase are solved separately through coupling of static pressure, shear stress and velocity at the interface. Several cases for jet distances and flowrates were investigated both numerically and experimentally with an air-water model. Favorable comparison of numerical results with experimental data confirms the validity of the present numerical approach. An existing phenomenological model for 'penetration depth' prediction was extended for smaller 3et exit height to jet diameter' ratios.

Jan 1, 1995

By V. L. Richards, S. N. Lekakh, S. A. Dutler

"This study presents determination on the thermal properties of investment casting shell molds used in casting process modeling. Superheat and latent heat from solidification and cooling of a casting can either be accumulated by ceramic shell for thin-walled casting or transfer to environment for massive casting. Heat capacity and thermal conductivity both play important roles in casting solidification. Thermal properties of ceramic shell depend on shell composition and fabrication techniques as well as thermal history during shell preparation process due to multiple phase transformations. Inverse modeling was combined with corrected Laser Flash method to determine the applicable thermal properties of the shell during casting solidification. Pure nickel was poured into ceramic shells containing two thermocouples and experimental cooling curves were obtained. These curves were then fitted to the model by adjusting temperature dependent heat capacity and thermal conductivity.IntroductionCasting solidification in investment casting shell affected by shell thermal properties including specific heat capacity and thermal conductivity. For relatively thin walled casting, most of the melt superheat and part of latent heat are accumulated by the shell. This process is mainly controlled by shell heat capacity. In the case of massive casting, significant part of latent heat transfers to environment through the shell so that this process is mainly controlled by shell thermal conductivity."

Jan 1, 2012

By Merete Tangstad, Ragnar Tronstad

Ferromanganese production in electrical furnaces is quite an old process. However, as the furnaces are getting bigger, the requirements of cost, yield, product quality, emissions and security are raised. With the increased expectations, the fundamental knowledge must follow. Within the last 25 years there has been a great effort both in the industry as well as the academic environment to push the limits of this process. This article will show some examples of improvements within fundamental data, reaction mechanisms and emissions over this time period.

Jan 1, 2014

By Hideki Yamamoto, Shigeno Matsumoto, Junji Shibata

"Some fundamental studies were carried out in order to produce composite powders comprising of two or three metal oxides ~y using liquid-liquid extraction and to develop the control technology of the particle size. The combination of samarium and cobalt was selected as the two component composite powders. Both stripping and crystallization occurred at the same time by emulsifying the organic phase loading the two metals extracted with Versatic Acid 10 and the aqueous solution containing oxalic acid. The effect of aqueous pH, oxalic acid concentration and agitation speed was examined on some properties such as crystallization percent, particle size and shape of each metal oxide powders obtained in this process. The analysis by using EDX showed that the two metal oxides were distributed uniformly.IntroductionComposite metal and metal oxide powders with high purity are indispensable as industrial materials in the fields of electrical engineering, electronics and metallurgy. It is difficult to mix metal powders or metal oxide powders uniformly for the production of alloy powders. If insoluble metal salts are allowed to collect as crystallization products in the crystallization-stripping process, the conventional melting and crushing process can be avoided. After mixing of the organic phase containing metals in fixed composition, fine metal and metal oxide powders of alloy composition are produced by using a crystallization-stripping method. Versatic Acid 10 and D2EHPA, both acidic extractants, were chosen in this experiment, and the metal oxide powders were produced by using oxalic acid as a crystallization reagent. Mixed metal oxalates containing samarium and cobalt were precipitated from the mixed organic phase containing these metals. Furthermore, the physical properties of the powders, such as particle size, shape and thermal decomposition, were measured in order to evaluate them for industrial purposes."

Jan 1, 2000

By Shiwei Sun, Hongxu Li, Xiangxin Hao, Xie Yang

"Environmental impact assessment of copper metallurgical processes will soon become a compulsory activity in the future. The goal of this work is to analyses the copper metallurgical processes including pyro-metallurgy and hydrometallurgy based on the life cycle assessment method implemented in GaBi software. The evaluation indicators such as global warming potential (GWP), acidification potential (AP), photochemical ozone creation potential (POCP) and human toxic potential (HTP) are taken into account. The results show that the major environmental impact phase in pyro-metallurgy derives from beneficiation because of the largest material and energy consumption. It is also shown that copper hydrometallurgy has significantly lower environmental impact than pyro-metallurgy. Based on the evaluation results, some corresponding optimization methods are recommended to reduce environmental impact.IntroductionCopper is an important metal in modem society due to its wide variety of uses, including electrical wiring, heat exchangers, piping and roof construction and increasingly consumer electronics. Demand for copper has increased dramatically over the past decades, driving production rates almost exponentially. Annual production of copper was estimated to be 20 million tonnes in 2012 with Chinese production at about 6.06 million ton in 2012P1. The production process of copper has environment impacts that often go unnoticed by the producer. Higher production, coupled with declining ore grades, is placing increasing pressure on the natural environment.Sound environmental management helps producers improve their manufacturing technique. LCA is a well-established tool for assessing environmental impact potential and can be readily adapted to map impact potential over time, which can be used to quantify the environment impacts of a product or a process [21. This is achieved by creating an inventory of all the energy and material flows used in the process's life cycle. The results of an LCA can be used to improve the operation of a process so that they have less impact on the environment."

Jan 1, 2014

By Yoshihiko Maeda

"Although Japanese mining industry once had been a polluter of toxic heavy metals and gasses, it has been struggling for improvement of environment at mining and smelting facilities under the strict Japanese regulations. Through these efforts, the industry has developed various environmental technologies to be applied in other industries and society.Recycling of metal scraps, for example, has been conducted at smelting facilities. Treatment of hazardous waste, cleanup of contaminated soil and management of landfill are other examples of application of mining and smelting technologies and facilities. In accordance with the worldwide environmental concerns, the industry has become one of the leading industries to promote ""Sustainable Development"", and it is expected further contribution in reducing various environmental burdens to earth by utilizing its mining and smelting technologies and facilities. Some of the examples of these applications are presented in this paper.IntroductionDowa Mining Co., Ltd., established in 1984, is known as one of the ~op Japanese producer of nonferrous metals. Base on its special expertise in the mining and smelting of complex ores, it has expanded its business areas to downstream activities ranging from highly purified metals and alloys, electronics materials, chemicals and related various businesses. Dowa Mining now is becoming more active in the field of waste treatment and recycling.Dowa Mining had operated some mines until 1980th, located at the western part and northern part of Honshuu Island in Japan; the former is pyrite mine while the later is ""Black Ore"" mine,· a complex sulfide ore composed of high grade of copper,· silver, lead and zinc. However, due to the strong yen began in1985; Dowa Mining closed its mining operation in 1994, and has sifted to mining operations in Mexico."

Jan 1, 2000

By Milton Manrique

The thermal decomposition of ilmenite concentrates in a non-transferred arc; thermal plasma flow reactor was investigated. The plasma torch was operated using argon-helium and argon-nitrogen mixtures as plasma gases. The effect of power, feed rate and particle size was studied. Products were characterized by XRD, SEM, TEM and ICP techniques. Free energy minimization plots were used to predict the thermodynamic behavior of the system under different operating conditions. The results of this investigation showed a significant segregation process where titanium-rich products are collected in the reactor, while iron-rich products are collected in the quenching box and filter. The average size of the product is in the sub- micron range. Titanium nitride was formed and condensed in the reactor zone when using an argon-nitrogen mixture as the plasma gas.

Jan 1, 1998

By John Fallavollita

Conventional gas atomization produces powders that vary widely in size distributions and microstructures, thus making it very costly to produce powders tailor made in a narrow size distribution and microstructure. Furthermore, it is difficult to determine the relationships between atomizer operating conditions and resulting powder characteristics. The Impulse Atomization Process (IAP) was developed at the Advanced Materials and Processing Laboratory to produce powders with narrow size distributions. Powders produced by the IAP were reproducible and their sizes could be easily controlled by adjusting experimental conditions. Characteristics of Zn, Sn-Pb, AI-Cu, and Cu powders will be described to illustrate the flexibility of the process to tailor-make powders.

Jan 1, 1994

By A. De, J. S. Zuback, T. Mukherjee, T. DebRoy

For successful commercial applications of additive manufacturing, metallic parts need to be defect free, structurally sound and reliable. However, additively manufactured metallic parts are susceptible to distortion, lack of fusion defects and compositional changes. Methods to measure susceptibilities of various alloys to these defects are needed but not currently available. Here we show that the necessary theories can be developed based on a well-tested numerical heat transfer and fluid flow model and decades of research in the field of welding. The proposed theories are validated with experimental results reported in the literature.

Jan 1, 2016

By Yongfeng Jia

Lime neutralization and co-precipitation of As(V) with iron(III) is the most widely used and most economical method for the removal of arsenic from mineral processing solutions and effluents. However, the arsenate fixation mechanism in the coprecipitated solids is not fully understood. It was suggested by various researchers to be a ferrihydrite precipitation process during which arsenate is removed by adsorption on ferrihydrite. In this study, XRD, EXAFS and microprobe were employed for the speciation of arsenic and the effect of various factors on arsenic solubility was also investigated. The results indicate that coprecipitation is a more complicated process than simple adsorption resulting in lower arsenic solubilities. Poorly crystalline ferric arsenate was observed for the first time to be present in the coprecipitated solids. In case of lime as base, there exists some type of Ca-Fe-arsenate association. A general term ?coprecipitate? is suggested to describe the precipitated arsenic-bearing solids instead of those widely used specific terms ?arsenical ferrihydrite? or ?arsenic-bearing ferrihydrite?.

Jan 1, 2005

By Kenshi Kawabata, Mitsuji Ueda, Junko Umeda, Katsuyoshi Kondoh, Kantarou Kaneko

Solid-state recycling process of in-house scraps of machined magnesium (Mg) alloy wastes has been established to directly produce wrought materials via the repetitively plastic deformation by Roll-compaction (RCP) and the conventional hot extrusion. The coarse chips, wasted in machining AMX602 (Mg-6Al-0.2Mn-2Ca) cast billets used for the gate bar used in Electronic Toll Collection (ETC) of the high-way system, were employed as the input materials in this study. RCP process enabled to serve coarse Mg alloy powder consisting of refined grains and intermetallics with no re-melting. They were easily consolidated by hot extrusion, and their wrought alloys showed both homogeneously refined grains less than 1~2 µm by dynamic recrystallization and randomized texture by repetitive plastic deformation on the input wastes. These materials revealed extremely advanced mechanical properties of high tensile strength of 356MPa and high ductility of 14.8%, compared to the originally virgin materials with 270MPa TS and 5% elongation. When applying the same Mg alloy wastes via RCP process to the mass production in the company, the large-scale extruded materials also indicated the superior tensile properties. It means that this direct solid-state process is held as “Up-grade recycle of metal wastes”.

Jan 1, 2008

By Neil Smith

Mineral processing plants typically procure a range of industrial services from contractors. Their satisfaction and value received is directly affected by how the services are procured, rationalized and delivered. Conventional purchasing strategies often focus on price rather than on optimizing the service relationship between supplier and customer. The nature of this relationship may have the greatest potential to reduce costs and enhance production. It has been documented that a service involves simultaneous production and consumption. A high degree of customer involvement is often necessary for a successful outcome and the expectations and attitudes of the customer can positively or negatively affect delivery of the service. This indicates that the customer can enhance or diminish their own satisfaction and value received and the supplier cannot act alone for best results. The Optimax? Program for industrial services is a service delivery framework whereby a customer and supplier work together to raise the efficiency of the service exchange. The Optimax? Program is intended to help the customer optimize costs and maximize production by connecting the customer and supplier through shared information and objectives. This paper will review the basic nature of services, provide a couple of examples of conventional procurement strategies for services and outline the features of the Optimax? Program. A Case Study showing recent results from implementing the Optimax? Program will be included.

Jan 1, 2006

By C. Lupi

Electric arc furnace dust generated during the production of steels is regarded as hazardous waste because of the presence of leachable elements such as Cr, Pb, Cd .... Different processes are available according to the management policy chosen by the steelmaker: disposal. recycle and/or recovery. The feasibility of an hydrometallurgical Zn recovery process on fumes generated during the pyrometallurgical treatment of EAF dust has been investigated. The recovery of metallic iron, chromium and nickel as molten metal provides fumes very rich in zinc oxide ( 63.1% ) and poor in zinc ferrite. This secondary dust is still an hazardous waste and represents the raw material for the recovery of Zn and Pb. The waste material is first leached in 1.5 M sulphuric acid at 30°C to provide a Zn, Fe and Mn rich aqueous solution and a Pb and Ca sulphate rich sludge. The iron is eliminated by precipitation because is harmful to the following electrowinning process. The ftltered and purified leached solution is acidified in order to obtain good electrowinning conditions. A pure cathodic deposit of zinc is then produced in an electrolytic cell at laboratory scale.

Jan 1, 1996

By J. M. Tourre

1995 have seen a continuation of a positive trend in the Rare Earth industry The availability of a greater diversity of Raw Material has brought additional flexibility to the Producers permitting better economics China remains the major raw material source; Chinese concentrate producers have increased capacity in 1995 (Baotou, Sichuan, etc) China's role in the Rare Earth industry will continue to evolve; the acquisition of a majority equity position by San Huan/CNNC will have a significant impact on both the Rare Earth and Magnet markets Chinese producers are increasing the quality of their products and realize their true values Chinese market, itself, is also changing as the internal needs for separated rare earth's grow Already already producer of Lamps, Loudspeakers, Magnets, and TV tubes, China is in an unique position where the potential of its internal market might be more promising than the prospects outside China 1995 has also seen the application market become more diverse and complex. There are new applications growing at a very strong pace (such as battery alloy), applications that are now penetrating their target markets with significantly increased growth rates (such as bonded NdFeB), and some applications that became more complex requiring much more sophisticated products (such as catalysis). Rare Earth producers have to spend significant ressources in order to monitor the market trends in order to predict the demand and then adjust their raw material mix. Even though there is a greater diversity of raw material available, there is still some Rare Earth elements that are in excess, while other are just in balance. As a consequence rare earth producers invest heavily in R&D in order to develop new applications for these excess elements.

Jan 1, 1997