Search Documents

By Maura Malone, Neil Gao, Daniel Liu

"Corrosion is the primary failure mode for aluminum cathode sheets used in Teck's Trail Operations electrolytic zinc plant. It was observed that the corrosion performance of Al cathodes from different suppliers varied considerably. This suggests that the material properties of Al cathodes have a strong influence on corrosion resistance. In the current study, various types of Al alloys, including 1050, 1060, 1070, HIS and 1090, were characterized through chemical analysis, corrosion testing, mechanical testing and metallography. The results are discussed with a focus on the effects of impurity elements and second phase particles on corrosion resistance. The findings were used to improve the Al cathode sheet specification and to develop a standardized screening procedure which details qualification steps for comprehensive evaluation prior to a plant trial.IntroductionAluminum (Al) cathode replacement is a major operating expense at Teck's Trail Operations zinc electrolytic plant. Currently, approximately 0.5% of daily stripped Al cathodes are removed from service because of failures caused mainly by corrosion. Edge corrosion and acid (solution) line corrosion are the most severe types of corrosion, resulting in more than 50% of cathode failures.Corrosion of Al cathodes has been intensively investigated for over two decades and the origins and mechanisms of Al cathode corrosion are well understood [1-4]. Halide anions contained in the electrolyte are the primary culprits for the corrosion and sticking problems of Al cathodes. Both fluoride (F') and chloride (Cl"") result in localized passivity breakdown on the surface of the Al cathode, causing pitting corrosion. Bouarzaiga investigated the corrosion of Al cathode samples partially immersed in electrolyte and found that the formation of Ch at the electrolyte/air interface was the primary contributor to solution line corrosion [2]. Because of the significant impact of F"" and Cl"" on Al cathode corrosion, it is imperative to maintain these concentrations as low as possible in the electrolyte."

Jan 1, 2012

By N. A. Vatolin, L. I. Leontjev, S. V. Shavrin

The ever growing interest to the complex iron ores may be attributed to possible production of the naturally alloyed metals and the efficient recovery of the associated elements. However, the conventional technique for complex ore processing is complicated and in some cases even impossible. A pyrometallurgical benefiation of such ores without melted slag formation has been advanced. A version of the technique assumes pellet production with metal coagulated within a slag shell on grinding the pellets, the metal phase is mechanically separated from the slag shell. The technique has been run up with ferro chromo nickel, high-titanium, high-magnesia, alumina phosphorus ores and concentrates. Another version of the pyrometallurgical benefication without melted slag formation in a rotary kiln has been developed from the schemes for processing red mud of alumina manufacture and high-titanium concentrates. Means have been put up to improve schemes available for lex iron ore processing with primary emphasis on material pretreatment before blast furnace and steelmaking processes. Vanadium-bearing titanomagnetite conentrate oxidized pellets possess low strength at reduction. The technique suggested for pelletizing in the controlled atmosphere improves the afore said pellet metallurgical properties. Prodution of metallized pellets in a conveyor roasting machine holds considerable promise for blast furnace and steelmaking processes. In processing the high-sulphur iron ores still another technique is proposed to roast the fluxed pellets with 95% and more desulphuration.

Jan 1, 1988

By Yanxia Lu

Porous silicon carbide (SiC) has been the top selection for diesel particular filters (DPFs) since 2000 because of its high thermal diffusivity and strong body, which help it to survive in the harsh environment of a diesel exhaust system. However, the process to produce SiC DPFs is a costly one. The work presented herein describes more cost effective composite materials for this application, namely Si-SiC and Si₃N₄-SiC. Both composites have shown excellent filtration efficiency, low back pressure and outstanding survivability of regeneration at high soot loadings. Since the composites are batched from silicon metal, they can be prepared by a low temperature process that is impossible in the production of pure SiC PDFs. In fact, fabrication of SiC composites simply involves reactions between nitrogen gas and silicon metal, or silicon metal bonded with SiC, and as such uses a much less costly process when compared to the one employed to make SiC. In addition, the pore structure of the composites can easily be tuned by selecting raw materials and changing the ratio of two components. A typical pore structure consists of well connected pores with a median pore size of 5-20 µm and a porosity of 40-55%. This talk will describe the exothermic behavior as well as the mechanical and thermal properties of SiC composites in comparison to those of SiC filters. It will also show the superior thermal shock resistance of Si₃N₄ bonded SiC which is due to the unique combination of these phases that lowers the thermal expansion and elastic modulus relative to pure SiC.

Jan 1, 2006

By P. A. Manohar

This paper describes an implementation of the Potts model for simulation of grain growth in 2D on a distributed-memory parallel architecture. The simulation scheme utilizes a continuous-time, asynchronous parallel version of the n-fold way algorithm. Each Processing Element (PE) carries a piece of the global simulation domain while the virtual topology of the PEs is in the form of a square grid in 2D and Torus in 3D. Different PEs have different local simulated times. Inter-processor communication is carried by the Message Passing Interface (MPI) routines. Sample results for grain growth simulation in 2D are presented for a 840 x 840 global domain size distributed over 16 PEs. The grain growth kinetics obtained in the simulation of pure, isotropic systems is in good agreement with the theory. Grain size distributions obtained in the parallel simulation are well described by the lognormal distribution, thus validating the simulation procedure. Keywords: Metropolis algorithm. n-fold way algorithm, asynchronous parallelization, grain growth

Jan 1, 2003

By A. McLean, S. Dawson, N. D. G. Mountford

"IntroductionIn order to predict the accepted industrial practice for the year 2000, it may be helpful to first consider the rate of development of scientific knowledge. If the speed with which man can travel on commercial vehicles is taken as a criterion for determining the rate of progression, then it can be seen from Figure 1 that advancement in our present century is very rapid. Likewise, if computer technology is used as a criterion for the measurement of scientific advancement, it becomes evident that technological evolution can be highly exponential. These two examples are sufficient to demonstrate that engineers and managers cannot afford to regard scientific development as being linear with respect to time if they are to avoid underestimating the needs of society.Within this framework of overall development, the time required for individual ideas to progress from inception to regular application has decreased considerably. For example, X-rays first discovered by Roentgen in the 1890's and now used widely in medicine and engineering, required a developmental period of some eighty years. The motorcar evolved from early beginnings at the turn of the century to a position of great social impact in sixty years. Rectifier materials used in high frequency radar to the present explosion in communications, required forty years. As illustrated in Figure 2, the period is shortening rapidly.The use of sound waves appears to be following a similar path. There is now a considerable body of knowledge concerning their behaviour and exceptional advances have been made. In medicine and engineering the sonic approach to examination is well established, and acoustic testing forms the basis of several diagnostic and quality control applications. With respect to metals engineering, ultrasonic testing has contributed to the understanding of the relationship between the size and number of internal defects and the probability of premature failure. This has allowed the designer to incorporate appropriate safety factors in his designs; but more importantly, the realization of the deleterious effect of inclusions on the performance of the final product has resulted in a continuous pressure on the material suppliers to reduce the number of defects in their products.It is not only the designer who is demanding defect free material but also the fabricator, as material breakdown during manufacture can be prohibitively expensive. Examples of this can be found in both the aluminum and steel industries where ultra clean sheet is required to ensure that rejections are minimized during beverage can manufacture and other deep drawing operations."

Jan 1, 1988

By Osarnu Inoue

In Mitsubishi Continuous Copper Smelting and Converting Process, smelting, slag-matte separation and matte converting are continuously carried out in series in three furnaces connected by launders. As a result of this operational configuration of the furnaces, influence of the change in operating condition in upper stream, such as variation of feeds in the smelting furnace, propagates to down stream with some delay. In order to achieve stabler operation, process control algorithm based on the dynamic characteristics of each furnace would be very effective. In this study, the dynamic process simulation model was developed for the smelting furnace. The model consists of two mathematical modules, i.e. the thermodynamic module and the mixing module. The calculation results using operating data obtained at Naoshima Smelter showed good agreement with the actually observed change in temperature, composition and flow rate of matte and slag at the outlet of the furnace. In addition, operation parameters such as reaction efficiency of oxygen and coal, dead volume of melts were estimated.

Jan 1, 1999

By Jack Thibodeau

During the past six years, most states have promulgated water quality regulations which contain numerical aquatic life standards for heavy metals. In addition, the Environmental Protection Agency (EPA) promulgated national water quality standards in 1992 which also include numerical aquatic life criteria for heavy metals. Numerous wastewater discharge permits have been issued by the states and EPA to industrial facilities which include low microgram per liter heavy metal limitations. In many instances, the limitations are below detection limits or treatability limits using state-of-the-art analytical methods or treatment technologies. This paper will discuss options for conducting studies, including the use of water-effect ratios, metal partitioning coefficients, and recalculation procedures to develop site-specific metals criteria and higher permit limitations. The installation of expensive metal treatment systems to remove trace metals may be avoided if higher permit limits are indicated by the site-specific studies.

Jan 1, 1996

By Ryosuke Matsuoka

Keywords: Tantalum capacitor, Scrap, Recovery, Titanium, Chlorination A recycling process for tantalum from capacitor scraps using an oxidation process followed by mechanical separation and chemical treatment was investigated. This study demonstrates that sintered tantalum electrodes inside the capacitor scraps can be mechanically collected after the oxidation of the scraps in air, and high-purity tantalum oxide powder (Ta2O5) was efficiently recovered after chemical treatment. By reducing the Ta2O5 obtained through magnesiothermic reduction, tantalum powder with 99 mass-% purity was obtained. Using the chlorination for tantalum recovery was also investigated, and the tantalum or tantalum compounds were reacted with chloride wastes such as FeClx. It was found that tantalum was effectively separated and purified when tantalum powder is reacted with FeClx at 1100 K under an argon atmosphere. This recycling process utilizing chloride scrap has now been extended to other reactive metals such as titanium.

Jan 1, 2004

By Gunnar Eriksson

Computer simulation has become an everyday practice in thennodynamic and materials research. Advanced thennochemical algorithms take into account heat transfer effects and salient reaction kinetics when applied for process models. In particular, the combination of mass transfer or overall reaction rates with multi-component Gibbs energy minimisation provides an effective tool for simulation of industrial thennochemical processes and processing of materials. In this work the combination of rate factors with the Gibbs energy technique was studied by using the novel program ChemSheet, which operates through Microsoft's Excel® spreadsheets. Such processes as, for example, CVD of pure silicon production, titania pigment manufacturing, vapour pressure of Mercury in amalgams (in Hg-Iamp manufacturing) and melting behaviour of low-temperature alloys have been modelled. Provided that the thennochemical data is available simulations can be performed with any thennodynamic system. The calculation can be performed as an affinity study without a particular reactor model or with a specific reactor scheme.

Jan 1, 2001

By Zhanjun Wang, Yongqi Sun, Mei Zhang, Zuotai Zhang, Min Guo

The role of fluorine on the viscous and crystallization behavior of CaO-SiO2-MgO-Al2O3-FetO-P2O5-(CaF2) slags were explored using the rotating cylinder method, non-isothermal differential scanning calorimeter (DSC), X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. It was found that the viscosity slightly decreased with increasing CaF2 content. It was also found that CaF2 addition can promote the primary phase transformed from MgFe2O4 spinel to Ca3(PO4)F, which was beneficial to the enrichment of phosphorus. Additionally, the structure of the slags explained by X-ray photoelectron spectroscopy (XPS) and magic angular spinning nuclear magnetic resonance (MAS-NMR) were further analyzed, which was well in accordance with the above analysis.

Jan 1, 2016

By Mao Chen, Baojun Zhao, Zhixiang Cui, Leonel Contreras

Viscosity is one of the important physiochemical properties of metallurgical slags which is important for slag tapping, metal loss in slag, freeze lining and fluid dynamics. High temperature viscosity measurements are time- and cost-consuming and the number of experiments is limited. Viscosity model is an effective way to predict the viscosities of the complex slags at high temperature. However, a reliable viscosity model can only be developed on the base of accurate experimental data. A unique high-temperature viscosity measurement apparatus developed at The University of Queensland enabled accurate viscosity data to be measured for the “FeO”-SiO2-CaO-MgO-Al2O3 system in equilibrium with Fe. An accurate viscosity model has been developed based on Eyring’s theory and extensive viscosity measurements. The viscosities of copper smelting, converting and cleaning slags over a wide range of compositions and temperatures can be predicted and applied in the process control.

Jan 1, 2016

By R. N. Reddy

The Pseudo capacitance of layered type Mn02 electrode material for electrochemical capacitors (EC's) was investigated. MnO2 was synthesized in our laboratory. Mn02 was prepared from heating of KMn04 at 300°C in air. Cyclic Voltammetry (CV) experiments were carried out using three electrode system, Saturated calomel electrode as reference electrode, platinum mesh as a counter electrode, and MnOz composite material mounted in a platinum mesh used as a working electrode. Two kinds of composite working electrode materials were used, one was mixture of MnOz and 25 wt% acetylene black, while the other was MnOz, 25 wt% acetylene black and 25 wt% carbon. All the experiments were carried out at 25OC. A maximum specific capacitance of 130 Fig and 118 Fig were observed at the scan rate of 2 mV/s and 20 mV/s respectively in 1M KC1 for composite electrode made with carbon. Results obtained in this study are compared with that of other electrode materials.

Jan 1, 2002

By Arvind Thekdi, Cynthia Belt2

"Waste heat from industrial operations in metals industry represents 20% to 50% of the total energy used in most manufacturing plants. Reduction and recovery of waste heat offers the most attractive and cost effective method of reducing energy intensity for an industrial plant to meet corporate energy saving goals. It is possible to reduce or recover 30% to 60% of the available waste heat by using conventional and readily available technologies. Projects to reduce or recovery waste heat may offer less than 3 years payback to as short as a few months. This paper presents information on most commonly used methods for waste heat reduction and recovery in the metals industry operations. It describes the methods and use of analysis tools that would allow a user to estimate energy savings, CO2 or GHG reduction potential, and economic benefit and includes appropriate case histories.Waste Heat SourcesSources of waste heat abound with the metals industry. While the overall quantity of energy is high, the sources are distributed throughout a plant. The largest source within the metals industry is within furnace exhaust / flue gases. This includes the high temperature gases from burners in process heating such melting, calcining, and sintering operations. It also includes lower temperature gases from heat treat, dryers, and heaters. Lower temperatures are also found after post processed hot gases. This could include heat left after heat exchangers, regenerative systems, thermal oxidizers, and emission control systems. Other hot gases include air used in direct and indirect cooling.While waste heat in form of exhaust gases is readily recognized, waste heat can also be found within liquids and solids. Waste heat within liquids includes things such as cooling water, heated wash water, and blow down water. Solids can be hot product at discharge after processing or reactions are complete. Indeed, not only is energy wasted in the hot metal that slowly air-cools, but additional energy may be used in providing air or water-cooling to increase the speed of cooling. Other waste heat sources are not as apparent and include things like hot surfaces, steam leaks, boiler blow down water, etc. Table 1 and Figure 1 show several major sources along with the temperature range and characteristics of the source."

Jan 1, 2011

By Zhang Libo, Wang Xin, Peng Jin-hui, Ju Shaohua, Guo Sheng-hui, Xu Lei, Huang Meng-yang

"China is lacking high grade titanium ores. This work intends to leach impurities such as Fe, Ca and Mg from a low grade titanium ore, to increase the grade. The original material contained 65% TiO2 , 16.12% Fe, 9.4% CaO + MgO, 4.2% SiO2, 1.25% A12O3, and the particle size is between 0.053-0.045mm. Microwave energy was used to enhance the leaching effect. The results showed that when normal heating was used to leach the mineral, the extraction of impurities Fe, Ca and Mg was very low. However, when microwave energy is introduced, the extraction of Fe, Ca and Mg increased dramatically. The optimized conditions are: relative power 5W/g, the ratio of concentrate to HC1 isl5%, leaching at 160°C for 20 min with a ratio of liquid to solid 12:1 mL/g. The material obtained under these conditions contains 92.73% TiO2, 0.207% Ca + Mg, 0.8% Fe, with 94.6% Ti recovery. The poduct meets with the quality for boiling chlorine.IntroductionThe resources of titanium are very abundant, and are distributed all over the world. There are almost 140 minerals containing TiO2 with a content of more than 1%. However, there are only several minerals which can be used for producing sponge titanium. They are mainly rutile and ilmenite. The grade of nature rutile concentrates is higher than 95% TiO2, and it is a high quality raw material. But the resources of nature rutile are relatively low; after mining for many years, its resources are exhausting gradually. Although ilmenite reserves are great, ilmenite cannot be used as a raw material because of its low content of TiO2, only 45-70%; also it has a high impurity content of Ca, Mg and Fe. In these years, there is a tendency for titanium industry to use high grade concentrate."

Jan 1, 2012

By S. Saptharishi

Selenium, which is a 6A group element of the periodic table, constitutes about 7x10-5 % of the earth?s crust. Even though selenium is a dispersed element with respect to its commercial exploitation, it is capable of forming number of minerals and nearly forty selenium minerals have been identified, out of which the copper ores are the richest sources of selenium. Electronics industries and glass industries are the major consumers of selenium, while pharma grade selenium used as micronutrient for humans and animals. Various methods have been developed to recover selenium as a by-product from copper anode slime during copper refining. Selenium being amphoteric in nature, it is soluble in both acid and alkali. While acid roast process is widely used, considerable work has been carried out in Russia for recovering selenium through alkali route. This paper enlightens the process developed at Central Research and Development Laboratory, for recovering selenium from decopperised slime through alkali pressure leaching. The decopperised slime is pressure leached with alkali under oxidizing conditions by which almost all the selenium present is converted to alkali selenate, which is easily separable from the rest of the decopperised slime. The solution so obtained is neutralized, during which, most of the impurities are precipitated out. Then selenium is precipitated in its elemental form upon purging sulphur-di-oxide under warm acidic medium. The purity of the selenium obtained by this process is higher than that of the selenium from acid roast process. Moreover selenium can be crystallized as sodium selenate and it can be marketed. The acidic content of the effluent is recovered and it is recycled back to the process. The sodium content of the effluent is converted into high purity sodium sulphate, which is marketable. The hazardous waste containing arsenic is precipitated as its sulphide and can be disposed off as landfill.

Jan 1, 2006

By Stephan Mulch, Christian His, Patrick M. Stephan, Thibault Champion

"When fuel costs increase dramatically, waste to energy (WTE) conversion technologies become a good alternative to produce energy. The potential energy available in domestic wastes, in developed countries, could be upwards of 4% of their total energy needs. Due to low energy recovery and low level of treated domestic wastes in many countries, the energy coming from waste is generally less than 0.5% of the country needs.Domestic waste incineration can convert heat to electricity for industry and housing and allow waste volume reduction in countries where land fills are a scarce resource.There is a request to improve existing combustion technology by increasing energy recovery with better heat transfer in the boiler and also by increasing lining durability with more resistant materials and technologies.The knowledge of corrosion phenomena and material performance allows Saint-Gobain Group to develop and propose high performance refractory lining solutions.IntroductionThe interest in alternative energy has been growing dramatically in the two last decades due to several combined factors, such as global energy demand, fuels prices evolution (e.g. crude oil, Figure 1) or environmental and geopolitics factors"

Jan 1, 2008

By Oleg I. Platonov

The process for desulfurizing coke oven gas in a regenerative system ?scrubber-stripper?, with sour gas being fed to Sulfur Recovery Unit (SRU) and tail gas being recycled to raw coke gas scrubber, has been developed. A key problem of this process is the presence of elemental sulfur in the SRU off-gas, which may deposit on gas-blowing equipment, thus disrupting its operation. A new treatment technology for SRU off-gas that has been worked out for a Claus unit operated by «Russian Metallurgical Company» (RMC) in Magnitogorsk (Russia) is presented. It incorporates a catalytic hydrolysis/hydrogenation stage, where all sulfur-bearing species such as sulfur dioxide, carbonyl sulfide and elemental sulfur are converted to hydrogen sulfide. The SRU in Magnitogorsk comprises three main units: gas re-heater; catalytic hydrolysis reactor and waste gas cooler. Re-heater is required to increase temperature of the process gas up to a level of catalytic conversion (beyond 330-3500C). Oxygen utilized as an oxidizing agent reduces the volume of waste gas to a minimal possible value. The operational data garnered since 16.07.2004 clearly shows that the new technology allows high-level purification of Claus tail gas from elemental sulfur. Unlike SCOT ? process, this technology does not require separate stages for H2S removal and enrichment that tangibly simplifies its implementation at lower capital and operation expenditures.

Jan 1, 2006

By George H. Edwards

Most cullets consumed in large-volume glass manufacturing processes receive little processing beyond crushing. But lead-glass cullets for specialty glasses such as industrial lighting refractors or cathode-ray tubes are combined with metals and various coatings that prohibit their direct recycling into the glass-melting processes that created them. In many cases, the contained lead renders these cullets hazardous. At present, virtually all industrial processes to separate one cullet from another depend on hand sorting, and thus are necessarily costly per unit weight. Lead-glass cullets of differing lead content are of interest because they offer the possibility of separating one glass composition from another by high-speed, automated processes at low cost. A potential process for comminution, cleaning, and separation of lead-glass cullets would involve primary and secondary crushing, magnetic and other metals separation, attrition scrubbing in water, separation of glass types by gravity techniques, drying if necessary, sampling, and preparation for transport to the point of use. Process water would be filtered to remove finely divided coating materials and glass, and reused. If carried out on a scale similar to a specialty industrial mineral processing plant, the cost per unit weight of such processing should be substantially less than the raw material value of the cullet in specialty glass production. The added value of avoiding waste disposal costs makes this process economically attractive.

Jan 1, 1994

By Zachery Zanetell

Flotation circuit performance has become increasingly more challenging due to the complexity of available ore sources. To optimize value mineral recovery, the mineralogical composition of the ore should be evaluated and understood. Utilizing a variety of mineralogical and analytical tools, flotation processing challenges can be overcome and potential limitations understood. In this paper, several case studies will be discussed in terms of the value that has been provided through the use of mineralogical analysis to optimize flotation performance.

By David E. Jones

In any manufacturing process, the generation of secondary, associated or waste products along with the primary product is inevitable. Today there is great emphasis on the concept of waste minimisation. As part of that overall strategy, the search .for markets for these materials formally regarded as wastes, can mean the development of whole new industries. This paper examines some of the work necessary to develop recycling and markets for associated products with particular reference to iron and steelmaking slags.

Jan 1, 1994