Search Documents

By D. Tahija

"Hecla's Greens Creek silver-gold-lead-zinc mill began using carbon dioxide rather than sulphuric acid to control pH in April, 2015. High pH levels in the grinding and lead flotation circuits are caused by the presence of re-mined cemented paste backfill in mill feed and need to be lowered to achieve good flotation response. Carbon dioxide has proven to be quite effective at controlling pH in the lead circuit with greatly improved pH target attainment. The allowable amount of carbon dioxide used is not limited by effects on lead-zinc selectivity and by poor froth characteristics, as was the case with sulphuric acid. Startup and implementation went smoothly, with few operational issues needing to be resolved. Early results from implementation of the system and its effects on mill performance will be presented. INTRODUCTION Hecla Greens Creek is a silver-gold-lead-zinc mine producing flotation lead and zinc concentrates, as well as a gravity gold concentrate. Besides their base metal contents, both the lead and zinc concentrates carry precious metals. The circuit is largely conventional, with SAG and ball mill grinding being followed by graphite removal preflotation, then conventional lead flotation and conventional zinc flotation. Both rougher concentrates are treated in regrind steps, followed by cleaner flotation. The cleaners tails are treated in an unorthodox bulk circuit to produce a low-grade zinc-lead concentrate marketed to Imperial Process smelters (1). BACKGROUND Backfill and Flotation pH The Greens Creek mine is an underground operation in which mined areas, after ore extraction, are backfilled, using rammed paste or pumped slurry. The backfill consists of mill tailings to which approximately five percent Portland or similar cement is added to enhance its compressive strength. Later mining near backfilled areas inevitably results in a considerable amount of old backfill being mixed with new ore before being shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed is often 20% to 25% and sometimes even higher. Commercial cement, and consequently backfill prepared using it, contains excess lime. Because of this, backfill in mill feed is indistinguishable from the addition of a large amount of lime, so mill natural pHs often range above 10 or even 11. Similar situations have been recognized for many years at mines throughout the world (2)."

Jan 1, 2016

By M. F. Martin

Dewatering aids are chemicals which enhance the efficiency of mechanical dewatering equipment such as vacuum disc filters and centrifugal dryers. A new dewatering aid has been developed which significantly lowers the moisture content of the mineral concentrate and causes none of the undesirable side effects normally associated with dewatering aids. Highlights of product development from laboratory screening through field testing will be discussed.

Jan 1, 1985

By B. K. Parekh

Large reserves of coal pond fines are found in the Illinois Basin-over 40 million tons in Western Kentucky, over 65 million tons in Southern Illinois, and over 35 million tons in Southern Indiana. If these fines are used to produce coal-water slurry (CWS), fuel costs, NOx. emissions, and pond closure costs can be reduced. Coal fines from this region that are used to produce CWS for co-fire or re-burn may require processing, however, to attain proper particle size distribution and fuel quality. To evaluate the effectiveness of using coal cleaning technologies to control these CWS quality parameters, a simple flowsheet for recovering and processing coal pond fines was designed and tested. Coal fines processing consisted of using classifying cyclones to size at nominal minus 200 mesh, cleaning the classifying cyclone underflow using spirals, and cleaning the overflow using column froth flotation. Ash content of the dean coal from the spiral was reduced to about 10 percent, which is satisfactory to use for CWS co-firing in a cyclone-fired boiler. The clean coal from column flotation may be used for re-burn in a cyclone-fired boiler or as co-fire fuel in a wall-fired or tangentially-fired boiler. Heating value recovery during laboratory-scale, pilot-scale, and commercial-scale coal cleaning testing was about 80 percent.

Jan 1, 1998

By Robert Charles Alfred

Evolution is continuing in the field of rock drilling, Campbell Limestone Company is experimenting in the higher air pressure phase of drilling, It has been determined that there is a definite relationship between Air Pressure, Penetration Rate, Bit & Tool Wear and Life, In our drilling we have determined that &e higher air pressure gives a better penetration rate with less bit wear per foot. Drilling with 180 to 200 PSI air pressure, instead of 100 PSI for air and/or churn drills, has decreased our primary costs by approximately one half.

Jan 1, 1963

By V. M. Johnston

The most abundant fuel resource in the U.S.A. is also the most under-utilized. Proven reserves of bituminous coal, sub-bituminous and lignite constitute from 60% to 90% of our total fossil fuel reserves -- dependent upon the parameters used by the analyst making the estimate. Despite this ample supply, bituminous coal provided only 20% of U. S. energy consumption in 1967 and 1968, this dropping to 17.57 in 1971 and 1972. By 1978, according to my projections, 16.7% of the Nation's mechanical energy will come from bituminous coal. However, our energy needs are growing at such a rate that the 20.6% provided by bituminous in 1967 equalled 480 million tons while the 16.7% of U. S. consumption visualized for 1978 will require nearly 650 million tons. In order to view coal's position with perspective in this developing energy crunch, it is necessary to examine the total energy situation. To this end, I have prepared a couple of tables which you should have before you. I chose this procedure rather than slides because I would need to utilize an entire wall to make the data visible to an audience. Therefore, I refer you to the long sheet entitled "U. S. Energy Consumption - Trillion Btu - 1967-1978." As you can see from the heading, I am confining my treatment of the problem to the intermediate term. In the long run, if we are willing to pay the cost, we can do a lot of things, including the complete conversion of coal into a sulfur-free fuel.

Jan 1, 1973

By M. Wasel

The Gross Rosebel gold deposits are located in the Guiana Shield of north central Suriname. Initial discovery of surficial gold in 1880 by local artisanal miners preceded small-scale mechanized mining from 1885 to 1939. The first systematic exploration program was carried out by Placer Development from 1974 to 1977. In May 1992 Golden Star Resources optioned the property. Initial shallow reconnaissance diamond drilling of the extensive surface geochemical anomalies intersected sporadic gold mineralization with no apparent continuity between drill sections. Successive deep augering, trenching and systematic grid drilling based on information from surface mapping allowed development of a preliminary geological model. Further drilling of specific structural-lithologic targets and more complete synthesis of geological data from the trenching and deep auger sampling added to the geological model and defined the multiple controls of gold mineralization. Carefully planned infill drilling on a tighter grid spacing resulted in progressive definition of reserves within six discrete gold deposits. In a complex geological setting, the key to success at Gross Rosebel was persistent, systematic exploration, detailed mapping, careful core logging and perceptive geological interpretation. Reserves now stand at 48.6 Mt at 1.6 glt Au, or 2.4 million ounces of gold. The purpose of this paper is to describe the progression of exploration activity that led to the definition of substantial gold reserves and to summarize the geology of the deposits.

Jan 1, 1998

By R. R. Johnson

The Hama Mining Company owns and operates The Groveland Mine near Iron Mountain, in the Upper Peninsula of Michigan. The orebody is part of the Menominee Range of the Lake Superior District. The ore (generally known as Jasper taconite) contains an average of 35% iron ranging from 28% to 39% with an overall split of 60% magnetite and 40% hematite. The variations encountered throughout the orebody require a certain amount of blending to reduce feed changes to the mill. One of the variables which affects the crushers, as well as the mill, is the range of hardness which has a low of 7.9 and a high of 24.6 as measured by the Bond Twin pendulum impact and crushing technique. Reference is made to hardness only to point out its effect on crushing and wear rate variations. Over a period of time, these variables do, of course, average out. Mining of the low grade ore started in 1959 and has operated continuously to date. Preparation of the feed for conventional rod and ball mill grinding is accomplished by three stages of crushing. Reduction of crude ore is first passed through a 54 inch gyratory crusher; then through a secondary crusher; followed by two or three tertiary crushers in closed circuit with screens as production quotas require (Figure 1). Current demand to the crushers is about 5,200,000 tons of crude ore per year.

Jan 1, 1976

By R. M. Cox

Pneumatic coal loading and conveying systems provide alternative methods for the safe and efficient mining of the thin high-grade coal seams found in the Southern Appalachians. Pneumatic systems eliminate most of the health and safety hazards associated with the operation of conventional mining and haulage equipment in small low-coal mines by removing powered mobile equipment from the mine. Ventilation is also improved by the coincidental removal of gas and respirable dust from the mine by the operation of the pneumatic loading and conveying system. Other significant advantages of pneumatic coal recovery systems are relative simplicity, operating flexibility, low capital cost, quiet operations, environmental benefits, and ease of automation. The design considerations and field evaluations of experimental prototype pneumatic coal loading and conveying systems, installed and operated in small thin-seam mines, are presented in this report. In addition, fundamental design criteria and recommendations for the installation and operation of a variety of pneumatic coal loading and conveying systems are proposed, which offer alternative coal recovery systems that alleviate the serious health and safety concerns of current small mine operations.

Jan 1, 1999

By J. J. Carlson

An important factor in filtration is the zeta potential of the particles. Since zeta potential is a function of pH, it was hypothesized that adding CO would lower the pH and zeta potential. A reduction in zeta potential should enhance the flocculation and increase the filtration rate. This paper describes the effects CO on the zeta potential of both pure hematite and samples of hematite concentrate from an iron ore processing plant. A significant shift in the zeta potential, as a function of pH, curve was observed. These results point to an alteration of the particles mineralogy, not just a shift in pH.

Jan 1, 2010

By M. E. Grimes

The Port Radium mine of Eldorado Mining and Refining Limited, located on Great Bear Lake only a few miles from the Arctic Circle in north-western Canada, is the oldest uranium producer in Canada, The first concentrates were produced in 1933 and except for a period between 1940 and 1942 the mill has operated continuously. Although it is located in a remote area, and compared to more recent mines in other areas is a small tonnage operation, nonetheless the relatively high grade of the Port Radium ore has permitted operation to date on an economical basis. The mill process at Port Radium includes the original gravity concentration mill, and since 1952 an acid leaching plant which treats tailings from the gravity mill and tailings recovered by dredging of residues from underwater dumps in Great Bear Lake. The pregnant solution from the leach plant has to date been processed through aluminum reduction to yield an intermediate grade uranous phosphate-arsenate precipitate, Because of the rising costs of the aluminum reduction process, and its sensitivity to ore composition, Eldorado became interested in possible application to Port Radium of the solvent extraction processes of which we were obtaining increasing information in the latter part of 1954 and during 1955.

Jan 1, 1958

By B. E. Davis

A problem that has continued to plague the Florida phosphate industry is the loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µ m) in a separate circuit have resulted in limited success, but recovery is still not optimum. The Bureau of Mines is investigating ways to improve the recovery of coarse phosphate through improvements in the conditioning step. Studies to optimize conditioning parameters such as agitation energy, conditioning time, conditioner solids, and residual clay content have resulted in improved P2O5 recovery. Optimizing these and other conditioning parameters resulted in a rougher concentrate grading 30 pct P2O5 with a P2O5 recovery of 97 pct.

Jan 1, 1993

By Robert J. Garino

Around two-thirds of world silver mine production comes from mines where the majority of ex-mill revenue is obtained from other metals. In this talk I will illustrate the importance of this output of silver as a by-product of the mining of various base metals. I will also consider the impact of relative changes in base and precious metal prices on mill-head revenue, and therefore, on production decisions. During the latter half of 1982 improving silver prices encouraged re-openings at several base metal mines. Thus some production of lead, zinc and copper can be regarded as partly conditional on the prevailing silver price. Conversely, a good deal of silver production can be considered to be independent of the silver price and dependent on the production of some base metal. It is the degree to which the value of silver mined affects the revenues of nominally, base metal, producers that is the central concern of this presentation.

Jan 1, 1983

By M. Dondi, M. Surracco, G. Alfano, P. Saba

Recent investigations on fine grinding with jet mill miprototypes of original design, constructed at the DIMM and Centro Studi of the National Research Council at Cagliari University, have led to the realization of a third generation micronizer characterized by large capacity and high efficiency. The new model and its distinctive features are described here and the results are presented of grinding tests on typical, high grade Sardinian minerals used for quality products. The operating principles of the jet mill are described in relation to the mechanico-elastic properties of the minerals treated. In particular the efficacy of the comminution process is demonstrated in terms of both solid treated and of impact, attrition and shearing forces generated in the micronizer. Particle size distribution of the finished products are reported, that satisfy the most stringent market specifications for the different minerals, as well as energy consumptions. The alternative operating options for solving particular grinding problems and minimizing energy consumption are discussed. Lastly, the main developments of the jet mill for a possible application at industrial scale are suggested.

Jan 1, 1995

By S. P. Winkelmann

The expansion in gold production in the Carlin 'Trend over the last few years has been one of staggering proportion. To increase gold production while minimizing capital requirements and providing for the safe and efficient mining and processing of ores has required a tremendous effort by the Mine Engineering group at Newmont Gold. This paper discusses the organizational changes implemented to effectively deal with a full range of engineering problems and how the Newmont Gold Mine Engineering group dealt with these problems. Specially developed computer software and their applications will be explained. Improvements in the techniques used in converting geologic resources into reserves, and in scheduling the mining of multiple pits to feed multiple processing facilities, as well as ore control procedures are presented. Current mine engineering practices are discussed.

Jan 1, 1990

By R. Yang

This paper presents a kinematic approach for blast modeling with examples of blast models that were developed previously. A kinematic approach was applied successfully in developing blasting models that can simulate all blast design parameters for field applications. Several applied blasting models have been developed and applied widely in the world. A kinematic approach to blast modeling refers to using measurements of kinematic quantities such as the velocity, strain, or displacement and well-established assumptions to model blasting phenomena, rather than being restricted to use first principal of physics, such as, the stress- and material-constitutive relations. The kinematic quantities are easy to measure in the field. Due to the complexity and inhomogeneity of rock mass properties, using first principles of physics, many parameters of rock and explosive properties must be involved, which are hard or impossible to quantify. This creates a major impediment when trying to simulate the total process of blasting based upon first principles of physics. The 3D kinematic model for muckpile formation was developed and applied to open pit blasts. The multiple blasthole fragmentation model developed during recent years has been applied successfully to many mine sites around the globe. These models are typical examples of blast modeling using the kinematic approach, which enables the models to catch major trends of the blasting process and explicitly simulate full blast design parameters and complex geometries. Blast modeling using the kinematic approach results in easy model calibration and validation against field measurements and effective applications to practical problems. Using kinematic models of the muckpile formation and the multiple blasthole fragmentation model, this paper demonstrates the merits of the kinematic approach for blast modeling. New developments of the models were also presented in the paper, which illustrate the potential of the kinematic modelling approach.

Mar 2, 2022

By Hsu-Hui Hsing

In several previous studies from this laboratory (1-4) the autophobicity concept of Zisman and co-workers (5, 6) has been extended to gas phase adsorption processes. Low molecular weight alcohols adsorb on silica or alumina to yield novel isotherms in that monolayer adsorption occurs at low relative pressures indicative of strong bonding, but subsequently multilayer adsorption is quite sparse and diminishes with molecular weight of the alcohol. Such isotherms fit no standard classification scheme, however, in the vacinity of monolayer coverage alcohol isotherms give an excellent fit to the Langmuir or B. E. T. , Type I model (7). Monolayer adsorption is relatively irreversible and it is thus possible to prepare these chemisorbed layers and perform subsequent adsorption studies thereon. All indications are that the adsorptive properties on such films is radically different from that on the underlying alumina (4, 8) and in one study finite contact angles for hydrocarbon fluids were observed. One perennial conceptual difficulty is that there is no observed upper bound to the adsorption isotherm which would be necessary for autophobic adsorption to occur. The cause for this has been studied, and it is currently believed that adsorption is complicated by reversible capillary condensation at contact points between powder particles. The evidence for this is that large particle powders give less "apparent" adsorption at high relative pressures and in one very tedious study adsorption on planar sheets, oxidized aluminum displayed similar reduced uptake at high relative pressures when compared with high specific surface area powders (3).

Jan 1, 1974

By Hans Breuer

The new regulations for the bituminous coal mining industry, issued by the mining authorities of the Federal Republic of Germany, are aimed at reducing to a feasible minimum any development of the coal workers pneumoconiosis (CWP) by lowering the admissible dust exposure of mine workers. Additional and improved measures of dust suppression and job assignment control *) are required for the purpose In this connection two basically different demands are placed on dust measurements: As far as dust suppression is concerned, the causes of dust development and the effectiveness of methods applied to reduce dust concentrations have to be identified, whereas with regard to the control of job assignment, the dust exposure of mine workers has to be depermined. Demands placed on dust measurements -- specifically for determining dust exposure -- are liable to become more severe since the threshold limit values were considerably reduced in these last years and since any additional dust suppression measures as well as a purposeful job assignment to certain mine workers are dependent on relevant measuring data. Therefore, research work has been carried out with the objective of measuring and evaluating, in terms of their effect (i. e. their incidence on the development of a CWP), size distribution, concentration, and specific noxiousness of any prevailing dust conditions.

Jan 1, 1980

By S. G. Ozkan

Boron minerals of economic importance are primarily colemanite, tincal, and ulexite. Turkey and the United States are the leading producers of boron minerals and compounds. Other production includes datolite in Russia and synthetic colemanite in Chile. This paper will discuss various types of chemical and physical treatments of boron ores to produce the marketable minerals and compounds that are consumed in commercial products.

Jan 1, 1995

By Peter B. Dowden, David T. Cass

A shield on a tunneling machine has two basic purposes. Firstly to provide temporary support in unstable ground, maintaining the integrity of the bore and protecting the operators, and secondly, in conjunction with other sealing devices, to prevent the ingress of water. In any specific tunnel, unstable ground and water may or may not occur together. Further, there are a number of different ground behaviors that may be termed unstable and these must be defined in order to determine the most suitable type of machine. Beyond the shield itself, the cutterhead and the mucking system design are critical in successfully traversing difficult geology. In any but the shortest tunnels, variations in the geological conditions and the requirement of an acceptable advance rate can impose increasing degrees of sophistication in the machine design. In this paper we will review current designs of shielded type machines and their application, and discuss new developments which blend hard and soft ground tunneling technology. We will also indicate that in some conditions, although first impressions seem to favor a shielded machine, in fact an open gripper TBM may be the wisest choice.

Jan 1, 1991

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill.

Jan 1, 1999