Search Documents

By T. W. Peglas, J. Doherty, R. A. Day

The South East Transit Project is a $520 million project in Brisbane, Australia which includes the construction of a 32 km Busway to access the south-eastern suburbs. Close to the centre of Brisbane, tunneling techniques have been used to minimise surface disruption. This paper describes some of the features of the longest driven tunnel on the project, the Vulture Street Tunnel. The Busway is a two lane expressway for buses which requires a 10.2 m finished width and a 12.6 m excavated span of driven tunnel. The Vulture Street Tunnel carries the Busway at minimal cover beneath the operating Vulture Street Railway Station, beneath a three storey office building and beneath the roadway to the Mater Hill Busway station. Halfway along the route, a Y-junction has been constructed to enable future connection with a light rail route. Key features in the design and construction of the Vulture Street Tunnel include: Use of canopy tubes to drive a 12 m wide tunnel beneath operating railway tracks with less than two metres of cover in highly weathered rock. Underpinning the office building in the route of the tunnel construction from within the building carpark. Construction of a 24 m span Y-junction with 7 metres cover of weathered and faulted rock. Use of predictive analysis as an adjunct to traditional back analysis to estimate the tunnel settlements from pressuremeter test results. This paper describes the design methodology with particular reference to settlement prediction, as well as construction innovations used to complete the tunnel. This paper will be of interest to all designers who have to create large spans in minimal cover in weak rock in urban areas and who have to predict the settlement

Jan 1, 2001

Barrick Gold plans to have four new gold mines in production by 2006. Together, the mines would increase the company’s output by 40 percent. The projects include Veladero in Argentina, Alto Chicama in Peru, Cowal in Australia and Tulawaka in Tanzania. All of them are scheduled to begin production between the first quarter of 2005 and the first quarter of 2006. They are expected to drive Barrick Gold’s growth profile to a target of 211.5 to 217.7 t (6.8 million to 7 mil-lion oz) of gold production in 2007. The company’s projected output for 2004 is 152.4 to 155.5 t (4.9 million to 5million oz) in 2004. Overall, higher production and lower costs are expected in the early years from the new mines.

Jan 1, 2004

By F. Calizaya

This paper describes the basic requirements for the utilization of belt air to ventilate working sections at remote locations in relation to the main fans. It highlights the risks involved, potential problems, and the provisions that must be followed by mine operators for the safe use of belt air. The paper also presents a brief review of the current regulations, conveyor belting tests, atmospheric monitoring system requirements, and the experience gained by mine operators to utilize the belt entries to ventilate remote working sections or areas where mechanized equipment is being installed or removed. The paper concludes with a set of recommendations with respect to the utilization of belt air and the composition of belt material in under-ground coal mines.

Jan 1, 2008

By T. R. Jr. McMillan

Introduction Examining the short- and long-term job prospects for engineers in the coal industry might include looking at coal tonnage projections, future export markets, federal regulations, and the decrease in overall graduates. But coal is the US most competitive basic industry. As such, why not go back to basics? That is, there are three basic challenges that need to be faced by students, faculty, and members of the coal industry. These challenges are counseling, career placement, and professionalism. Counseling Counseling can include elementary, high school, and college students, as well as individuals already employed. But what happens to students after they have selected a course of study at a particular university? As shown in Fig. 1, only 87,000, or 7.25% of our graduates have technical degrees. Generally, there is a strong market projected for these engineering graduates. However, many students who have majored in other nontechnical curriculums, have to scramble for jobs. This says something about our ability to make students aware of where the real job opportunities are. As a student spends four or five years pursuing a degree, he or she is looking for professional guidance. The student has the right to expect "real world" counseling - counseling that is not "the way it should be" but "the way it is." The influence of faculty members is significant. They should take this long opportunity to tell students not what they want to hear or what the problem's of academia or the industry are, but what the real job market is all about. If faculty do not use this opportunity, they in-advertently-through omission - mislead their students. Once a student graduates and is a working alumnus, faculty should take advantage of their relationship with the student and continue to stimulate conversation leading to a two-way exchange of ideas and information. Faculty should also encourage and solicit financial support for their mining departments from their alumni. These monies, in many cases, will be matched dollar for dollar or more, depending on the company the alumnus works for. In the private sector, the responsibility is to communicate with faculty and students. Alumni can be effective by participating in this two-way dialogue with their professors at meetings, technical seminars, and conventions. In many cases, alumni will employ summer or co-op students in their organizations. While getting to know these students, industry members should level with them on where the true opportunities are and what it takes to be successful. It is important to communicate with both faculty and students candidly on both the posi-

Jan 2, 1985

By Georgene Renner, William R. Yernberg, Steve Kral

ABB provides integrated pro-cess control, optimization and information systems, drives and power-distribution equipment as well as other services and support to the mining industry. ABB also supplies electrical equipment and control systems for the openpit mining industry. This includes products for the automation of electrical equipment in mine shovels. The company offers low- and medium-voltage drives for various mineral- industry applications. And ABB provides gearless mill drives for equipment, such as semiautogenous grinding mills that are too large for conventional drives. ABB Industrial IT provides innovative hardware and software systems that cover all the requirements of the modern mining and processing plant.

Jan 1, 2004

By Gary E. Slagel

The year was 1974. The event - the United States Congress was embroiled over what issues should be included in the proposed national surface mining law. The question - what should be done with underground mines? The leading bills ultimately addressed the environmental impacts associated with underground mines including provisions to protect the surface from subsidence impacts. Amid the fears that this subsidence language might discourage underground mining, sponsors of the bill were asked to explain the meaning of the provision that read "to prevent subsidence to the extent technologically and economically feasible." Was this an attempt to limit mining that caused planned and controlled subsidence? Former Deputy Director of the Office of Surface Mining, Dean Hunt, reviewed some of these historical events in a 1985 presentation before the Eastern Mineral Law Foundation. He reported that in 1974 Congressman Morris Udall took the floor to respond to these concerns expressed by other members of Congress and the industry. Mr. Hunt cited Congressman Udall's July 10, 1974 Congressional Record statement: "The House bill contemplates rules 'to prevent subsidence to the extent technologically and economically feasible.' The word prevent led to fears expressed by the Secretary of the Interior Morton, that the effect would be to outlaw longwall mining, with its obvious subsidence ... in fact the bill's sponsors consider longwall mining ecologically preferable and it and other methods of controlled subsidence are explicitly endorsed." Further, the report that accompanied the front-running bill, HR11500, provided the following clarification on the issue of subsidence prevention: "It is the intent of this section to provide the Secretary with the authority to require the design and conduct of underground mining methods to control subsidence to the extent technologically and economically feasible in order to protect the value and use of surface lands. Some of the measures available for subsidence control include: (1) leaving sufficient original mineral for support; (2) refraining from mining under certain areas---or (3) causing subsidence to occur at a predictable time and in a relatively uniform and predictable manner. This specifically allows for the uses of longwall and other mining techniques which completely remove the coal." It is clear from the preceding statements that Congress considered the removal of all the coal and causing subsidence in a predictable and uniform manner to be equal to or better than leaving support coal and causing no subsidence. While the actual provision in the bills talked of preventing subsidence, a subsequent exception made it clear that the real intent was to control it. This is evidenced in the specific planned subsidence language that appeared in the bills and ultimately in Section 516 (b) (1) of PL95-87, the Surface Mining Control and Reclamation Act. It reads: "...adopt measures...to prevent subsidence ... except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." In spite of this historic record that supports controlled subsidence, something has been lost in the implementation. The primary focus by many regulators over the past few years has been on the "prevent" aspect irrespective of mining method being used. This has appeared to change the original intent of Congress from one of controlling subsidence to one of minimizing damage. The objective of this report is to review some of the current regulatory issues that impede full extraction mining and offer some suggestions on possible ways to deal with these issues.

Jan 1, 1986

By Kevin Beirne

Most people involved in the mining industry are familiar with student-industry co-op work-study programs. Many colleges and universities have used them for years. Northern College’s Haileybury School of Mines student co-op program adds a new dimension of productivity to the college and the mining industry. The college is located in Hailey-bury, Ontario, Canada. An example of the program’s success is the school’s relationship with Sabin Metal’s SMC (Canada) Ltd.’s McAlpine Mill in Cobalt, Ontario. Students gain practical knowledge and experience while industry gains an eager-to-learn worker. And many of the college’s advanced research services are made available to industry to supplement their own capabilities. The McAlpine Mill was established to provide custom milling of slags and ores. It also recovers metal values from other products of the primary and secondary precious metal industries.

Jan 1, 1999

By W. R. Dengler, R. S. Brown

In 1974, Brunswick Mining and Smelting Corporation Limited started a 48 million dollar expansion programme at their property in Bathurst, New Brunswick. A portion of the expansion plans includes a 26 foot diameter 4,525 foot deep shaft, underground crusher and conveyor excavations and lower level access development. J. S. Redpath Limited was awarded the contract for the new shaft and associated rock work in May 1974. Brunswick Mining and Smelting Corporation Limited, a member of the Noranda Group, operate this 10,000 ton per day lead, zinc, copper plant with proven reserves in excess of 90 million tons. While most of the ore is provided by the underground operation at the Number 12 ore body, some tonnage is produced from the open pit at the Number 6 ore body. Long range plans indicate a phasing out of the open pit and an increase in production from the underground operation. Existing facilities at the underground mine could not provide additional tonnage, thus the requirement for a new shaft. (Figure 1) The new shaft will also provide access to ore below the 2,800 level which is currently the bottom level of the existing facility. The contract called for sinking a 26 foot inside diameter, nine compartment concrete shaft 4,525 feet deep (Figure 2). Station access and ramp development from existing workings would be required to the bottom of the new shaft. In addition, development work for new crushing and conveying facilities was needed simultaneous with the shaft sinking.

Jan 1, 1976

By S. C. Tadolini

Roof support systems have evolved from standing posts and timbers to a generation termed ?big nails? where steel bars are inserted into boreholes and anchored with expansion shells and/or resin cartridges. These systems have been effective but are limited to mining height. Additionally, the properties of steel do not resists shear forces or have the flexibility being required in difficult ground conditions. The next generation of roof support systems is coupling the best parts of the ?big nail? and resin grouted cable bolt systems. This paper will present the advanced technical solutions of the next generation of cable systems that includes an indented high-capacity PC-strand used with a variety of fixtures. Case histories of support applications will be presented.

Jan 1, 2012

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica surfaces immersed in solutions of hydrolysable cations and/or sodium oleate. Hydrophobic forces were observed at the pH range where the concentration of the singly-charged hydroxo-complexes (CaOH+ or MgOH+) in solution is the highest. In the absence of oleate, the adsorption of the hydroxo-complexes was indicated by the disappearance of the repulsive hydration force. These results suggest that the hydrolysable cations adsorb on silica as singly-charged hydroxo-complexes. Based on the results obtained in the present work, a model for the adsorption of hydrolysable cations has been developed.

Jan 1, 2009

By D. Olsen, S. Cole, J. Strid, G. Colzani

This paper focuses on the underground tunnel work at the Hollywood Water Quality Improvement Project (HWQIP) in Los Angeles, CA. The HWQIP is being constructed to provide a water distribution system to bypass the existing Hollywood Reservoir System, which supplies drinking water for 500,000 people. The major project features include, a 2.9-meter diameter 1,829 meter long bypass tunnel, a 1.8-meterdiameter 366 meter long utility tunnel, 3 jack and bore tunnels, two 136 million liters underground circumferentially wrapped pre-stressed concrete water storage tanks, associated piping, and mechanical facilities. The physical project location coupled with strong community involvement and stringent environmental concerns was a considerable driving force for this project located in the Cahuenga Pass area of the Hollywood Hills north of Los Angeles, CA.

Jan 1, 2001

By J. B. Hiskey

Introduction The domestic copper industry has suffered for some time from declining ore grades; rising costs associated with conventional mining, milling, smelting and refining; tightening environmental restrictions; and shrinking markets due to materials substitution. Ore grade depletion is a major problem. It is illustrated by the decline in average copper yield shown in Fig. 1. From 1979, copper grade has dropped 60%, lowering yields from 1.2% to 0.49% (Sousa, 1981). The US copper industry is taking drastic measures to enhance its competitive posture and to guarantee its future worldwide position. In a sense, this involves a general restructuring of the processing philosophy of US copper producers. Judging from recent trends, this restructuring relates to the application of solution mining techniques to the treatment of copper ores and low grade waste material. Recovering copper by leaching techniques has been practiced for centuries. As early as the mid-16th century, some Hungarian copper mines were recycling copper bearing leach solutions through waste heaps (Nash, 1912). In the US, recovering copper from dilute mine waters has been carried out for more than 100 years. There are, however, certain technical innovations that have elevated the importance of solution mining as a process for copper recovery. These include: • Advances in solvent extract-electrowinning (SX-EW); • Developments in acid and acid ferric cure processes for oxide and mixed oxide sulfide ores; • Improvements in heap and dump construction; and • Advances in in situ leaching technology. Generally, solution mining enjoys certain intrinsic advantages over conventional mining and milling. Compared to conventional milling, the combined capital and operating costs of leaching facilities are normally lower, start-up times are faster, and the leaching operation usually has less impact on the environment. Furthermore, solution mining represents an expedient way of extracting metals from small shallow deposits, and is particularly suited to the treatment of low grade sources. And, in the case of waste dump leaching, there is a tremendous resource in-place that has the mining cost already off the books. This paper updates current US copper solution mining trends. Solution mining systems Schlitt (1980) summarized the characteristics of the principle leach systems in the US. He pointed out that the wide variations in copper deposits make solution mining a more site-specific activity than conventional mining and milling. Heap leaching is usually selected for moderate to high grade ores having a copper mineralization that is amenable to acid leaching (oxides, silicates and certain sulfides). Higher grade ores mined specifically for heap leaching are usually treated to optimize copper extraction, therefore, crushing and some pretreatment (acid curing) may be justified. On the other hand, dump leaching practice usually involves leaching low grade waste rock placed on large dumps as dictated by topography and haulage costs. Mine waste is therefore treated in an uncrushed run-of-mine condition. Finally, in situ leaching is appropriate for either very deep ore bodies or for recovering copper from low grade rock left behind in abandoned pit walls, stopes, and subsidence zones from earlier mining activities. True in-situ solution mining should be defined as the leaching of ore in its original geologic setting. Heap leaching Heap leaching has a long history as a hydrometallurgical process for copper recovery. The methodology of heap leaching established at Rio Tinto in Spain more than 300 years ago is basically the same as that used today. Processing concepts, such as solution management (sprinklers and leach/rest cycles) and copper

Jan 11, 1986

By Geoffrey Fosbrook, Donald Phillips, Anil Parikh

The Second Avenue Subway is a $16.8 billion project planned by the Metropolitan Transportation Authority (MTA) in New York City. It will reduce overcrowding and delays on the Lexington Avenue Line, improving travel for both city and suburban commuters, and improving access to mass transit for residents of the East Side of Manhattan. The project is a new, two-track, 13.5 km (8.5 mile) subway extending from Lexington Avenue at 125th Street in Harlem on the north end of Manhattan, to Water Street at Hanover Square in Lower Manhattan. The first phase of construction includes rock tunnels from 92nd Street to 62nd Street and connection to the existing 63rd Street station, three new stations, and track and systems from 105th Street to 63rd Street, allowing service between 96th Street and Brooklyn via an existing Broadway Line. The following describes the Project in detail, discusses the construction challenges addressed in the design, and the initial design/build contract to be awarded in 2005. A discussion of the planned mined construction of two rock caverns and a cut-and-cover station construction are also included.

Jan 1, 2005

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at tem¬peratures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Forma¬tion changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite.

Jan 1, 2007

By F. Mendaña

The characteristics of the igneous and metamorphic bedrock, extra-hard and abrasive, of the Guadarrama Tunnels, a bi-tube project of length 28.4 km without any intermediate attack, are first commented upon. Next, a detailed discussion is given of the most relevant aspects of the performance of the four double shield type TBMs. The experience of this leads to various recommendations to be borne in mind in future designs of TBM having to work in rock of similar characteristics.

Jan 1, 2007

By H. H. Murray

The largest reserves of palygorskite in the world are located in Anhui and Jiangsu Provinces in East Central China. The deposits are Middle Miocene in age and range from 3 to 6 m in thickness. The deposits are the alteration product of basaltic volcanic ash. The Chinese Geological Survey estimates the palygorskite reserves are in excess of 200 million tons. The elongate particle shape results in unique colloidal properties. Large quantities are exported to Japan, Taiwan, Southeast Asia, New Zealand, Australia, and West and Gulf Coasts of the United States. The markets include agricultural carriers, paint, joint tape compounds, animal feed binders, catalyst support, drilling muds, and suspending agents for chemicals, pharmaceuticals, and medicines. The viscosity is high and the quartz content is generally 5% or less.

Jan 1, 2009

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at temperatures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Formation changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite. © 2007 Elsevier Inc. All rights reserved. Keywords: Biwabik Iron Formation; Duluth Complex; Mineralogy

Jan 1, 2007

By S. F. Diehl

Drill cores from uranium roll-front deposits, hosted in lower Cretaceous strata, were examined from the proposed Dewey Burdock in-situ uranium recovery site in the northern part of the Edgemont uranium district, South Dakota. Uraninite (UO2), coffinite U(SiO4)0.9(OH)0.4, and doloresite (H8V6O16) occur as pore-occluding cements within the Fall River Formation in the Dewey area. In contrast, within the Lakota Formation in the Burdock area, uranium (with very little vanadium) is absorbed onto woody fragments and amorphous carbonaceous material in pressure-solution seams. Both areas have typical uranium roll-front mineralogy with 0.5 wt. % pyrite in the reduced solid phase and no pyrite in the oxidized solid phase. The groundwater at the ore zone is not oxygenated, so the uranium is relatively insoluble. Uranium in solution in ground waters is <10µg/L at Dewey and <22 µg/L at Burdock. Micromineralogic and geochemical data are being used to understand water/rock interactions, uranium distribution and movement, and as input factors for predictive reactive transport models.

Feb 27, 2013

By D. M. Lane, J. M. Berkoe

Engineers and Owners share a common desire to build reliable, efficient plants on schedule at reasonable costs. This paper describes one tool that Bechtel finds can integrate these objectives by “putting innovation into practice”. Examples of such innovative engineering practice include the use of computational fluid dynamics (CFD) to determine efficient designs. This paper outlines several examples of CFD applications on actual Mining and Metals Projects from around the world. The focus here is to highlight the modeling objectives, analysis strategy, actual benefit obtained from the work, lessons learned to improve future efforts and the common mistakes that can obscure the correct or best results, despite impressive graphics. The tools are powerful, and the results are more powerful when applied with skilled and well-directed human effort and ingenuity.

Jan 1, 2000