Search Documents

By Patricia Pride, Mike Robison, Jon Bergenthal, Wojciech Klecan

"The Lower and Middle River Des Peres (LMRDP) CSO Storage Tunnel is the largest single component of Metropolitan St. Louis Sewer District’s (MSD) CSO control system improvements planned to meet consent decree requirements for MSD’s Lemay Service Area. The 13.7-km (8.5-mile) long, deep, hard rock tunnel will have a finished diameter of 9.1 m (30 ft). Beginning at the Lemay Wastewater Treatment Plant (WWTP), the alignment follows the channelized River Des Peres to the outfall of the existing Forest Park tubes, as indicated in Fig. 1.The project includes three construction shafts, 34 intakes and a deep, cavern-style pump station located adjacent to the WWTP. The tunnel will be driven from the Defense Mapping shaft to the Macklind shaft. Another shaft is located near the midpoint at the tunnel in River Des Peres Park.The Forest Park intake, located at the upstream end of the tunnel just beyond the Macklind shaft, is a large, tangential vortex intake structure. With a peak flow rate of 170 m3/s (6,000 cfs), it will have a 6.1-m (20-ft) diameter dropshaft to transfer flow into the tunnel.The project includes another three large tangential vortex-flow intake structures with peak flow rates ranging from 28 to 44.5 m3/s (990 to 1,570 cfs). These large intakes are located at points where three large sewers (formerly creeks) enter the River Des Peres. Dropshaft diameters for these intakes range from 3 to 3.7 m (10 to 12 ft) in diameter. The 30 remaining intakes are smaller tangential vortex-style, with dropshafts in the range of 0.8 to 1.7 m (30 to 66 in.) in diameter.Each intake structure drops flow into a deaeration chamber constructed adjacent to the tunnel at tunnel depth. Intake tunnels transfer flow from the deaeration chambers to the main tunnel. Most of the intake tunnels are short. However, two are long. The Glaise Creek tunnel will extend 762 m (2,500 ft) from the main tunnel to the Alaska Park intake, while the Rock Creek tunnel will extend 823 m (2,700 ft) from the main tunnel to the Rock Creek intake. The dewatering pump station, located at the downstream end of the tunnel, will be built inside a large, horseshoe-shaped cavern with two access shafts. Excavation of the cavern and its access shafts will be performed by the tunnel contractor. Build-out of the dewatering pump station will be performed under separate contract."

Jun 1, 2019

By George D. Brunton

The past and present argillaceous rock studies for the U.S. National Waste Terminal Storage Program consist of: (1) evaluation of the geological characteristics of several wide- spread argillaceous formations in the United States; (2) laboratory studies of the physical and chemical properties of selected argillaceous rock samples; and (3) two full-scale in situ surface heater experiments that simulate the emplacement of heat-generating radioactive waste in argillaceous rock.

Jan 1, 1981

By John Murray, Daniel Ebin, Robert Gould, Yiming Sun, Lizan Gilbert

The Atlanta Plane Train Tunnel West Extension is being constructed at Hartsfield-Jackson Atlanta International Airport using the Sequential Excavation Method (SEM). The tunnel has shallow ground cover and mixed-face conditions and passes underneath the SkyTrain and MARTA stations and airport terminal buildings. It includes a twin tube Bifurcation with a span of over 45 feet and ground cover of 12 feet. A flat roof is being constructed at the Bifurcation to maximize rock cover and minimize surface settlements. This paper focuses on design and construction challenges for the Bifurcation and tunneling beneath the world’s busiest airport, while minimizing impacts to operations.

Dec 1, 2022

By Arthur Miller

Most of the production of copper in the United States comes from a few large companies. Often overlooked, however, are the more numerous small mining operations, which collectively produce a significant portion of the nation's copper. The objective of this paper is to describe the operations of a small mining company - Ranchers Exploration and Development Corporation - how it views its place in this industry of giants, how it exploits the advantages offered by its relatively small size, and how it protects itself from the hazards being small introduces. Environment is, of course, a critical factor for such a company because it does not have the resources which help large companies weather periods of financial stress. Ideally, this environment is characterized by a heal thy economy, strong product demand, relatively stable prices , adequate grades and tonnages of ore commensurate with depth and over-burden, ready access to utilities, a dependable labor pool, and suitable technical "know how". When the environment is right, properties which were previously uneconomical to operate attract the attention of companies whose primary interest is a return on investment commensurate with risk over a reasonable period of time. Naturally, the amount of the investment and the duration of operation determines the size of the company which would be interested in such a venture. Such is the case with Ranchers Bluebird Mine at Miami, Arizona - a small property operated by a small company in a favorable economic environment.

Jan 1, 1967

By Thomas V. Mullen

Some 146 kt (4.69 billion oz) of gold have been mined throughout history. Of this, 70% has been mined in this century alone, with 17% produced from 1985 through 1996 (Fig. 1 and Table 1). Until the mid-19th century, placers were the chief source of gold. Advancements in mining, metallurgy and geological thinking have resulted in underground mining (first of veins plus stockworks and later of Rand-type deposits) becoming the principal source of gold. With the demise of the South African deposits and the move towards lower grade ores, the primary source of gold will be from disseminated deposits exploited through large, open-pit mines. For the past 200 years, there has been a fairly constant ratio of about 31 g (1 oz) of gold to each person alive. If this ratio is to be maintained, annual gold production will have to rise from about 2.3 kt/a (73.9 million oz/year) to more than 3.1 kt/a (99.7 million oz/year) by the year 2000. To effect this increase, an unforeseen breakthrough in exploration or metallurgy is needed. Barring this, there will be pressure for an increase in the price of gold. This article traces the historical production of gold from 4000 B.C. - the earliest record of gold mining - to today and relates this 6,000-year record to advances in geological thinking, mining engineering and extractive metallurgy. It also proposes that man's thirst for gold, reflected in the price he will pay for gold, and his ability to find, mine and refine gold have combined to effect an equilibrium based loosely on the historical ratio of 31 g (1 oz) of cumulative gold production per each man or woman alive.

Jan 1, 1998

By Brad Simser

Several case histories from Glencore’s Sudbury Operations show how passive seismic monitoring data is used for geotechnical decision making. The data comes from three different seismic arrays monitoring two open stoping deposits, and a narrow vein cut and fill/blasthole operation. Mining depths range between 1000 to 1680m below surface. The deposits are hosted in hard igneous rocks typical of the Sudbury basin, with characteristically high horizontal stress (approximately 1.8 times the depth of overburden). Rockbursting is the main geotechnical risk, due to the strong brittle nature of the rock and local high mining extraction. Fault related seismicity includes both fault slip events, and the stress channelling effect as the mining front approaches a major fault structure. Planar data trends generally line up with known faults and often indicate early stage fault activation. The structures are risk ranked based on their seismic response. This has been particularly useful at the Nickel Rim South Mine (NRS) where the structural fabric (jointing and small-scale faulting) is generally parallel to the more through going faults. The persistence of structures is difficult to measure, and the NRS faults generally have low offsets and thin gouge. The visual difference between the more persistent structures that occasionally generate large seismic events (up Mw 2.9 to date) and localised joints/slips is often minor. The seismic monitoring data clearly shows the more active structures. This information is highlighted on mine plans to help guide enhanced ground support and seismic re-entry protocol barricade locations. Pillar loading/yielding is a key element to the blasthole operations where a primary/secondary mining sequence is used. The secondary pillars are mined in a yielded state with just-in-time development. An example of the seismic signature of a secondary stope is shown with emphasis on the need for high location accuracy given the stope widths of 12.5 to 15m. The ratio of the shear wave energy to primary wave energy (Es/Ep) has long been used as a method to estimate source mechanisms; the higher the ratio, the more likely the event is fault slip versus rock fracturing. Data sets are filtered on Es/Ep ratios to highlight both fault slip populations and stress fracturing mechanisms. Examples of seismic data quality checks, high stress development, and re-entry protocols are also shown in the case histories.

Apr 26, 2022

By Dermot M. Ross-Brown

The objectives of this generic study were to use numerical modeling techniques to determine under what conditions seismic waves generated by an earthquake might cause instability to an underground opening, or cause fracturing and joint movement that would lead to an increase in the permeability of the rock mass. In general, the study showed that moderate earthquakes (up to 0.41 g) did not cause instability of the tunnel or major fracturing of the rock mass. An artificial rock-burst tremor with high accelerations, however, was found to be amplified around the tunnel, and fracturing occurred as a result of the seismic loading in salt and granite. In shale, even moderate seismic loading resulted in tunnel collapse.

Jan 1, 1981

By K. Biswas

For the pillars, which have been standing long after mining, the stability depends much on the weathering action in the presence of mine moisture. From the field observations, it has been found that this weathering action becomes critical in terms of pillar stability if the coal seam contains partings or binders in it. The weathering action degrades both the partings and coal in terms of their load bearing capacity as the mine moisture penetrates into them. This paper investigates the effect of weathering action on coal and partings in the laboratory. In the field, the strength profile in the coal and the partings and the effect of time (in terms of the pillar age) on them have been studied by using borehole penetrometer. In this paper, an attempt has also been made to establish formulae for time dependent strength of coal and partings.

Jan 1, 1997

By J. Drelich

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size and distribution of mineral inclusions in coal on its wettability are briefly reviewed.

Jan 1, 1999

By L. A. Alcorn, H. E. Camargo, G. Gwaltney

"Una de las enfermedades más extendidas en la industria minera es la pérdida de audición inducida por el ruido. La exposición de los mineros a niveles de ruido superiores a los niveles de exposición permisibles resulta en la pérdida de audición de aproximadamente el 80% de los mineros del carbón a la edad de jubilarse. En este contexto, el Instituto Nacional para la Seguridad y Salud Ocupacional (NIOSH, por sus siglas en inglés) está realizando investigaciones para desarrollar controles de ruido aplicados a los sistemas de minado de tajeos largos. Este método de minado es usado para extraer la mitad de la producción nacional de carbón subterránea. A partir de las mediciones en campo, se determinó en investigaciones anteriores que los componentes dominantes que generan sonido en el cizallador de un sistema de tajeos largos son los dos tambores de corte utilizados para extraer el carbón. Debido a las dimensiones y complejidad de los sistemas de minado de tajeos largos, el proyecto NIOSH desarrolló un modelo de elementos finitos validado del tambor de corte para utilizarlo en la predicción del sonido generado por este debido a las fuerzas de excitación experimentadas en las operaciones subterráneas. Este mismo modelo se utilizará para desarrollar controles de ingeniería para el ruido del tambor. Las fuerzas de excitación surgen de la interacción de la broca de corte y el carbón, y se transmiten al tambor de corte a través de los sujetadores de brocas. Debido a las condiciones adversas en el frente y la falta de instrumentación aprobada para uso subterráneo, las fuerzas operativas de corte de carbón no han sido evaluadas anteriormente. Para este fin, NIOSH, en colaboración con la Universidad Tecnológica de Michigan, desarrolló una broca instrumentada autónoma con seguridad intrínseca para medir estas fuerzas. Este artículo describe el desarrollo de la broca instrumentada y la medición de las fuerzas operativas de corte de carbón en tres minas. Las mediciones revelaron que las fuerzas tienen un espectro plano, algo característico de la naturaleza del impacto de estas fuerzas, hasta alrededor de 100 Hz. Por encima de esta frecuencia "cutoff", la magnitud de la fuerza disminuye a una razón proporcional al cuadrado de la inversa de la frecuencia."

Jan 1, 2014

"The National Mining Hall of Fame and Museum (NMHF&M) announced the 2015 National Mining Hall of Fame inductees and the 2015 Prazen Award winner. This year’s inductees, selected by the National Mining Hall of Fame’s Board of Governors, represent the technology, management, mineral policy, education and health and safety aspects of the mining industry. They envelope a diverse cross section of the mining industry and were selected for being visionaries, leaders, educators and ambassadors.In 2015, Frank F. Aplan, T S Ary, Ralph E. Bailey, John Campbell Greenway and Edward Steidle will join 227 other mining industry honorees when formally inducted into the National Mining Hall of Fame. The Prazen Living Legend of Mining Award will go to the Powell River Project Research and Education Center, a partnership of Virginia Polytechnic Institute and State University (Virginia Tech) and the Appalachian coal mining industry.The 2015 annual induction banquet and ceremony will be the 28th such event and will be held this year in Pittsburgh, PA, on Oct. 23, 2015, in the Omni William Penn Hotel ballroom.2015 National Mining Hall of Fame inductees:Frank F. Aplan is among the most influential mineral processing leaders in both industry and academia. His studies of the processes involved in the preparation of coal and mineral ores are acknowledged worldwide for their broad applicability. An authority on flotation, Aplan is especially known for his studies of the wetting of solids and their control through the adsorption of surfactant films, and for his work on atomic defects on properties and behavior of solid-liquid interfaces."

Jan 1, 2015

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

The level of automation employed in flotation production is relatively low. In an actual concentrator, operators use their judgment to adjust the production state based on the visual characteristics of the flotation froth surface. There are shortcomings, such as strong subjectivity and lagging process operation, that easily cause the waste of manpower and material resources. Machine vision technology is introduced to replace human visualization, achieving a quantitative description of the visual characteristics of the froth surface. The state variable parameters are provided for the identification of the flotation conditions.

By Ken E. Baylis

Current over-capacity in coal production provides assured and relatively low-cost supplies to coal importers. At the same time, it is of serious concern to coal producers who invested considerable sums in the expectation that overseas demand would continue to grow rapidly. This paper assesses the reserves available for export, the export facilities, the coal supplies which can be put through them, and the market prospects for the future. It assumes, rightly or wrongly, that there will be no major and prolonged disruptions in supply from any major sources of coal. COAL RESERVES FOR EXPORT Economically recoverable reserves in the non-communist world amount to about 470 billion tonnes. These are sufficient to sustain current production levels of 2 billion tonnes a year for 235 years.

Jan 1, 1984

By Martin B. Treuhaft

Expectations for coal in the early to mid-1970's prompted the government and industry to pursue research and development programs to increase underground and surface mining coal productivity and net coal recovery. Several programs concerned advanced surface mining methods for thin seam coal recovery. Three such programs, along with related areas of interest, are presented in this paper, namely: (1) extended depth augering for trench-strip applications; (2) high recovery auger heads for enhanced recovery; and (3) variable wall mining in low cover longwalls. Conceptual development is examined, prototype testing is discussed, and potential operations are considered.

Jan 1, 1983

By James A. Finch

The Gaudin lecture is devoted to fundamentals. Given my involvement with column flotation over the last 20 years, this is my topic. I have tried to identify spinoff basic research and provide a personal list of favorites. Two are selected for discussion here. They are single bubble rise and bubble surface area flux. The rationale for such work, as well as some of the findings, are reviewed. Support for fundamental work seems as volatile as the economy (and the link is probably not coincidental). I hope some utility to the minerals industry is evident in the text. Column flotation in its current form originated in the early 1960s. The method was invented by Boutin, patented by Boutin and Tremblay and pursued doggedly by Wheeler. Their aim was to overcome the problem of mechanical entrainment of fine particles in the water carried by the bubbles, which they were convinced contributed to lowering flotation concentrate grades (Wheeler, 1988; Finch and Dobby, 1990). The solution was a combination of columnar geometry, the addition of wash water into a deep froth and the maintenance of an excess of water to the tailings, as compared to the feed (a so-called positive bias). Success at Les Mines Gaspe, Quebec, on cleaning Mo in the early 1980s signaled the start of industrial acceptance, making the column one of the flotation machines of choice today. Over the next 20 years, column applications mushroomed to cover virtually all mineral commodities, as well as nonmineral applications such as soil decontamination, deoiling of water and deinking of recycled paper. In the wake, research groups are continuing to probe the fundamentals, conferences and workshops have been transferring the technology and specialist companies have emerged to service the demand. Innovations were triggered as problems arose (for instance, in gas injection systems) and novel flotation cells, much in vogue in the 1990s, had the door opened. Mechanical cell manufacturers have not been idle - there is nothing like competition to provoke a fresh look at an established business. Flotation-cell technology has probably not seen so much activity since the patent rush in the early days of flotation, which occurred around the turn of the century. For an industry often considered reluctant to risk innovation, this is not a bad record. A good idea will find a place, but patience (not always an innovators strong suit) and careful preparation are required. Two books (Finch and Dobby, 1990; Rubenstein, 1996), three symposia (Sastry, 1988; Agar and Huls, 1991; Gomez and Finch, 1996), and a series of reviews (Dobby and Finch, 1991; Finch and Dobby, 1991; Finch, 1995; Finch et al., 1995) document the period. Like many good ideas, column flotation has been overexposed, and there have been disappointments. In a recent example, columns performing scavenging duty were replaced by mechanical cells (Chong et al., 1998). The further applications stray from the original - to

Jan 1, 1999

By W. Hitchcock

To enable the analysis of stability for a mine feasibility study a variety of geotechnical engineering parameters need to be obtained. At the early stage of a project it is usual for those responsible for the study to require a wide spatial distribution of RC holes in order to define a resource at the lowest possible cost. By the time a geotechnical study has commenced drilling priorities have usually switched to improving the definition of a resource, by drilling with diamond coring methods in the central area of the main orebody. The usual timing for geotechnical data collection is therefore after a wide distribution of holes have been drilled but which contain little geotechnical information. Conventional methods employed usually involve estimation methods, including book values and examination of disturbed core, or expensive additional drilling. With downhole geophysical methods we can economically take advantage of existing holes to obtain continuous values for density, defect orientation and ranking, elastic modulus values, unconfined compressive strength estimates and fracture frequency. This paper presents the results of a geophysical study and discusses the advantages and potential pitfalls of the method as compared to conventional methods of data collection.

Jan 1, 1999

By Z. T. Bieniawski

Ground support requirements for safe and economical design of room and pillar coal mining layouts are reviewed. The design methods for mine roofs and mine pillars are discussed and the role of the geotechnical aspects is considered. It is shown that current support design procedures in the United States do not utilize fully the latest research findings and the need for more effective technology transfer in coal mine ground control is emphasized. Promising new developments in ground support are identified and possible research areas are suggested.

Jan 1, 1982

By J. Iannicelli

Spray drying is the principal drying method used in the production of over six million tons annually of beneficiated kaolin in Georgia. Thirty-three dryers in the Georgia Kaolin belt comprise the highest concentration of large tonnage spray dryers in the world. The steady growth of spray drying in the U.S. kaolin industry is paced by advances in design and development of large spray dryers which have led to large scale new applications in mining and related industries.

Jan 1, 1982

By Atta Ur Rehman, Kwame Awuah-Offei

This work evaluated the effect of bucket orientation and operating parameters on resistive forces and penetration for rubber tire loaders. The work used a 1:16 scale LHD model to test a rubber tire loader (RTL) bucket operating at different levels of tractive effort, speed, digging height, and rake angles in a full factorial design experiment. The work repeated the test on two different muck piles with different particle sizes and used generalized regression modeling to test the association of rake angle, tractive effort, speed, and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort, and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle, and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The observation that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces is a novel contribution that enhances our understanding of RTL loading. The results also show that the effect of speed, tractive effort, and height above the floor all change with changes in particle sizes. This work adds to the literature on the effect of rake angle, height above the floor, tractive effort, and speed on penetration and resistive forces for rubber tire loaders.

Aug 24, 2020

By F. S. Knoll

Electrostatic separation is one of the most misunderstood physical processes used to beneficiate minerals. Nonetheless, millions of tons of titanium ores, iron ores and other minerals are processed every year economically, efficiently and safely. Over the past ten years major advances in electrostatic separation and its application have occurred. New processes include dewatering clay slurries, separating halite and sylvite, and shape separation of vermiculite and gangue minerals. Electrostatic separation techniques are based on one of two methods, electrophoresis or dieleccrophoresis -- processes involving charged and uncharged particles respectively. In some cases, the combination of these two techniques has proven quite useful. The purpose of this paper is to provide a basic understanding of the physical processes collectively called "electro- static separation" in order to enhance one's ability to define and consider new possibilities in mineral processing and other fields.

Jan 1, 1984