Search Documents

By K. S. Raja, B. Pesic, S. Kshetri

"We investigated the electrochemical corrosion behavior of commercial permanent magnetic material (NdFeB alloy) in 0.1 M NaH2PO4 solution (pH:4.75) containing 0 – 1000 ppm of chloride at room temperature (298 K). The material was evaluated in magnetized and demagnetized condition with different surface preparations such as: Ni-Cu-Ni coated, uncoated (bare), and anodized (in fluoride containing ethylene glycol at 60 V for 15 minutes to form a thick nanoporous oxide surface). The nickel coated magnetic sample showed reasonable pitting corrosion resistance up to 100 ppm chloride addition. The uncoated samples showed passivity in chloride free phosphate solution. Chloride additions caused pitting and the pitting protection potential was equal to the corrosion potential with 100 ppm chloride addition. Demagnetization did not alter the electrochemical polarization. However, the passive film formed on the magnetic sample showed higher charge carrier density than the film formed on the demagnetized sample. INTRODUCTIONSintered NdFeB permanent magnets exhibit excellent magnetic properties such as large energy product [(BH)max > 450 kJ/m3], high saturation magnetization (1.6 Tesla), and high coercivity (1.2 – 2.08 x 106 A/m) (Sugimoto, 2011). However, the NdFeB magnets are prone to corrosion attack because of the presence of Nd-rich intermetallic phases, such as Nd4Fe (Jurczyk & Jakubowicz, 2000). Nd-rich and B-rich intermetallic phases are distributed in a matrix of Nd2Fe14B tetragonal ferromagnetic compound in a permanent magnet. Generally, several types of Nd-rich phases are present in the magnet with Fe:Nd ratios ranging from 1:1.2 to 1:7. The volume fractions of Nd-rich and B-rich (Nd1+xFe4B4 type) phases are about 10% and 7% respectively (Li, Ma, Li, & Wang, 2011) . Among these intermetallic phases, Nd-rich phase has the most active electrochemical potential. Therefore, dissolution of this phase occurs in preference to other phases by galvanic corrosion when exposed to moisture. Since Nd-rich phases are present at the grain boundaries of the Nd2Fe14B matrix, corrosion leads to disintegration of the magnet."

Jan 1, 2012

By J. G. Conaway, P. G. Killeen

"Gamma-ray spectral logging, a useful technique for uranium exploration and evaluation, has generally been underutilized by the Canadian mining industry. Provided that the technique is properly applied, it is capable of yielding reliable quantitative information regarding the distribution of uranium and other radioelements along the borehole under most conditions.In practice. there are numerous factors which potentially can degrade the quality of the log and thus any quantitative interpretation based on it. Fortunately, the appropriate choice of logging equipment and technique can avoid many such problems, and corrections can be applied to the data to compensate for most of the others."

Jan 1, 1980

By Robert B. Parsons

"On February 15, 1984 Finance Minister Lalonde presented to Parliament a budget heavily flavoured with the current consultative mood of the Government. Notably absent from the budget was the typically long list of tax changes of immediate effect. Instead, the bulk of the budget papers consisted of a wide variety of white papers on significant topics that would have a far reaching impact on the future of all Canadians.This month. Tax Notes examines the highlights of Mr. Lalonde's budget.IntroductionThe mining industry need not feel slighted in Finance Minister Lalonde's budget of February 15, 1984: the budget offered very little that would have an immediate impact of significance on any sector of the economy. Apart from some welcome announcements for the oil and gas industry to postpone the implementation of certain negative tax changes, the budget was surprisingly scant in terms of definitive tax proposals.While massive revisions in the rules relating to pensions, small businesses, commodity taxation and profit-sharing were brought forward, many of these proposals are set out in White Papers or other documents to be implemented into legislation only after further consultation. Canadians will accordingly have to wait for such promised benefits as increased RRSP and other pension contribution limits."

Jan 1, 1984

By M. Pelser, H. Gous, J. H. W. M. Brits, K. Voogt

The effect of impurities; iron and selenium, on current efficiency and deposit quality in copper electrowinning was investigated using an at-line cell at the Rustenburg Base Metals Refiners’ Copper Tankhouse. The tankhouse is a direct leach, starter sheet electrowinning operation with a unique electrolyte composition. The effect of iron on the current efficiency in the at-line cell was found to be less severe than reported in literature. However, the distinction between the chemical impact of iron on current efficiency and the physical impact of iron on a starter sheet operation needs to be realised. The effect of selenium on current efficiency and deposit quality is also reported. INTRODUCTION Anglo American Platinum’s Rustenburg Base Metals Refiners’ (RBMR) Copper Tankhouse serves a unique function in the refinery flowsheet in that its primary functions are the removal of copper and production of acid for the leach circuit. This function needs to be performed to specification in order to keep the leach circuit operating optimally. Current efficiency is seen as an indicator of tankhouse performance and efficient energy use. The tankhouse plates starter sheets onto titanium blanks which, after stripping and preparation, return into the production cells for further plating. Approximately 78% of tankhouses surveyed (Robinson et al., 2013) use permanent cathode technology whereas older, smaller operations still use starter sheet technology. Drawbacks of the starter sheet technology are that the starters are thin and bend easily leading to increased shorts, they need to be removed after two days of plating to be manually straightened and are then returned to the cells. In addition, the electrolyte levels in the cells need to be adjusted during the plating cycle to improve loop adhesion to the cathode and reduce loop corrosion. The starter sheet technology is therefore very labour intensive and the final quality of the product is dependent on the quality of the starter sheets produced. In comparison, permanent cathode or direct plating technology lends itself to automation, allows for higher current densities and better cathode quality due to more robust geometric stability in the cell. The present barrier to implementation of permanent cathode plating at the RBMR Copper Tankhouse is the capital cost required to convert the tankhouse, i.e. blanks and stripping machine. At present, alternatives to titanium blanks, such as LDX 2101, are being investigated for the unique electrolyte composition of this tankhouse.

Jan 1, 2019

By A. McLean, D. K. A Donyina, R. S. Segsworth

"Various aspects of processing ferro-manganese fines generated during the crushing of standard ferro-manganese have been studied in laboratory-scaleplasma furnaces. These laboratory furnaces are based on the use of conventional graphite electrodes rather than water-cooled non-consumable torch devices. The reactor system has separate, distinct zones for pre-healing, melting and smelting. This unique feature assists in the removal of undesirable elements from the molten alloy. Ferro-manganese alloys containing over 82% manganese, 0.004% sulphur, less than 0.01% silicon, 0.006% nitrogen, 0.001% oxygen and 0.0006% hydrogen have been produced from the offgrade ferro-manganese fines.IntroductionThe major application of manganese is as an alloying additive to numerous metals such as steel, aluminum, copper and magnesium. Manganese is mainly consumed in the ferrous industry in the form of ferro-manganese and silicon-manganese, or in its pure state as electrolytic manganese when certain impurities inherent in the manufacture of ferro-manganese and silicon-manganese alloys must be avoided. Before being sold on the market, ferro-manganese is crushed and during this process alloy fines are generated. Due to the nature of the casting process, the fines produced are contaminated with silica sand. In addition, due to segregation effect s, the pho sphorus content of the alloy fines is higher than that found in the bulk of the material produced. Because of the smaller particle size and the higher impurity content, there is only a limited market available for the alloy fines. For this reason, there has been increasing attention directed toward the development of processes for recycling fines through the conventional smelting furnaces. The fines may be charged to the furnace either directly or after agglomeration. The detrimental effects of charging the fines directly include:(1) decrease in gas permeability, causing irregular gas flow;(2) increase in the amount of dust produced;(3) packing and bridging; and(4) intensive reactions due to sudden flow in hot zones."

Jan 1, 1982

By C. Dodds, R. S. Ferrari-John, The University of Nottingham, G. Dimitrakis, J. Katrib, A. R. Batchelor

"Sorting technologies have the potential to reduce energy use in comminution by rejecting uneconomic ore before feed material enters the mill. However, a major challenge for sorting porphyry copper ores is providing a basis of discrimination between valuable and non-valuable fragments, due to their complex mineralogies and textural features. Microwave heating in combination with infra-red detection (MW-IR) has been shown to provide upgraded feedstock for certain ores at bench scale. Selective heating of copper sulphide minerals compared to the gangue leads to an increased thermal response for valuable fragments, providing the basis for sorting.Rapid scale up of MW-IR from bench scale to a 100 t/h continuous pilot plant facility has been facilitated by the design of microwave choking structures to allow continuous operation at industrially meaningful throughputs, whilst meeting health and safety and electromagnetic compliance standards, and the integration of materials handling with electromagnetic systems.Laboratory batch testing on a pilot scale microwave system has been undertaken to investigate the thermal response of copper ores under industrial conditions, at microwave energy inputs up to 1 kWh/t. These results provided the operating window and recommended test conditions for the continuous pilot plant. Sortability curves predicted in the laboratory are in good agreement with separations achieved during continuous pilot plant operations. The potential microwave sortability of a number of ores has been studied, allowing informed decisions to be made about potential ore candidates based on mineralogy. Future development of the technology will be underpinned by the creation and validation of scale up concepts for 1000 t/h operations. Understanding the value proposition for individual sites/applications will be central to unlocking the potential economic and environmental benefits of microwave sorting."

Jan 1, 2016

By M. Scobie, G. R. Baiden

"This paper describes recent developments at Inco Limited, Ontario Division, in the field of information systems for automated mining. A CA TV cable network has been combined with a broad spectrum radio antenna system to allow the supply of voice, data and video services to underground mining. The system formed the basis of a field experiment at the Copper Cliff North Mine of the Ontario Division in 1990.The experimental information system was developed to supply underground mining with voice, data and video services to mobile and stationary locations. In order to test the communication system, telephones and radios were linked together with the outside phone lines for voice communication. Stationary data was implemented on a SCADA (Supervisory Control and Data Acquisition) system for mine monitoring and control using PLCs (Programmable Logic Controllers), while using personal workstations for the mine planning and engineering functions. Stationary video was installed in the experiment to observe crushing, conveyor transfer points and skip dumping areas. Mobile data and video were tested by the teleoperation of an LHD. The functions supplied to the vehicle were monitored through a computer, with control being maintained through a standard radio interface and real time video pictures for the operation of the machine.This paper discusses the field testing of the information system and results achieved to date. It concludes by discussing the options considered to be open to provide information systems for future automated mining."

Jan 1, 1992

By Alan G. Galley

"Advances in our knowledge of the petrochemical attributes of deposit environments and of the character and extent of hydrothermal systems associated with certain deposit types has resulted in increased application of lithogeochemistry to exploration programs. Lithogeochemistry can be used to vector an exploration program toward an area of high potential through the use of a series of collapsing scales of analysis from a tectonic subprovince down to a particular stratigraphic segment. In the case of volcanogenic massive sulphide (VMS) deposits this involves the recognition ofsuitable volcanic domains, and the identification of subvolcanic intrusions and cogenetic felsic extrusive complexes. The recognition of chemical vectors within regional-scale alteration zones and associated chemical sedimentary rocks allows the geologist to identify the stratigraphic units with the most potential for hosting a base metal deposit.An integrated lithogeochemical program requires the judicious use of major, trace and rare-earth element and isotopic analysis. Standard discriminant plots may be employed to identify suitable tectonic and lithologic environments. Analysis of the chemical and mineralogical variations in broad-scale, semi-comfortable alteration zones provides a useful set of vectors to VMS mineralization. These may include contouring raw data, element ratios on XY plots, normalizing data against known rock values, or calculating mass changes in alteration zones."

Jan 1, 1995

By Leroy G. Hagenbuch

"IntroductionAn integrated Truck Management Information System (Truck MIS) evolves as seemingly separate functions combined to yield a single homogeneous result / product. The concept of a computer integrated Truck MIS includes truck dispatch, truck maintenance management and truck weighing.A truck management system is only as good as the information / data bases input to it. The concept of an integrated system works best with automated data gathering. Automated data gathering provides timely and normally, the most accurate historical information/data bases. Data bases are, however, historical, which is a problem to be overcome in a computerized truck management information system, especially in regards to a truck dispatch system as loading sites / loading conditions and some dump site conditions continually change. As these changes occur, data base s must change as well, and thus the need for the continual update of data bases that the computer uses for a Truck MIS.For a truck dispatch system to achieve reliability / viability, dispatch decisions need to revolve around real time data gathered in an automated way. Integration of all truck management function s through automated data gathering lead s to the best over-all system.An integrated system is a combination of many different factors and is only as good as each factor / building block put in the system. With the proper building blocks, an integrated Truck MIS is very feasible - an MIS System that includes weighing, time and motion study, truck maintenance and maintenance management, as well as truck dispatch.Truck MISAn integrated Truck MIS provides for truck dispatch as the ultimate end result, a truly automated /integrated truck dispatch system (to function non-operator-dependent). The following comprises its central building blocks:-Time.- Haul Cycle Segments.Truck Status, i.e. Load on truck,- being loaded,- loaded,- unloaded,- in service,- out of service.- Vehicle Location.Loading Equipment Status.- in service,- out of service.Optional- distance travelled in each haul segment.With this data provided on a non-operator dependent basis, it is possible to build good data bases so a computer can make truck dispatch decisions. Knowing what information is needed as the central core to a good Truck MIS, how can this information be automatically gathered and fed into a central control computer?"

Jan 1, 1986

By P. E. Weidmark

"CANMET InformationPART 1-Published PapersAsmis, H. W., ""The dynamic response of caverns in discontinuous rock""; Proc 22nd U.S. Symposium on Rock Mechanics, Cambridge, Mass, June 1981, 272-277; 1981.Austin , M.W., Bray, J.W. and Crawford, A.M., ""A comparison of two indirect boundary element formulations incorporating planes of weakness"" ; Technical Note; Int J Rock Mech Min Sci Geomech Abstr; 19:339-344; 1982.Barrett, J. R., ""Applying geotechnical theory to underground metalliferous mining""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 210-222; 1983.Barron, K., Wright, P.L. and Smales, T., ""Guideline s for the design of coal pillars in the No .4 seam at Mclntyre Mines Ltd ., Grande Cache, Alberta""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of A IMMPE; 559-578; 1983.Bauer, A., ""Wall control blasting in open pit mines""; Mining Engng; 34:155-158; 1982.Bieniawski, Z.T., "" Improved design o f room-and-pillar coal mines for U.S. conditions""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 19-51; 1982.Blackwell, G.H. and Calder, P.N., ""Practical aspects of wall stability at Brenda Mines Ltd., Peachland, BC""; 3rd Intnl Conf on Stability in Surface Mining; Vancouver, BC, June 1981; SME-A1ME; 3:573-608; 1982.Blake, W., ""Microseismic monitoring for underground stability "" ; Proc 1st Intnl Cont on Stability in Underground Mining; Vancouver , BC, August 1982; SME of AIMMPE; 272-294; 1983.Brawner, C.O., ""Stabilization of rock slopes"" ; 3rd Intnl Conf on Stability in Surface Mining; Vancouver, BC, June 1981; SME-AIME; 3:289-310; 1982.Bridges, M.C., ""Review of open stope mining in Australia""; Proc 1st lntnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 813-828: 1983."

Jan 1, 1983

By K. D. Eng, W. T. Tierney

"During the past century, the development of vehicular transportation has benefitted tremendously from the performance improvement in engines in a situation where low-cost, plentiful fuel supplies were the order of the day. Engine advances were enhanced by and also dictated fuel modification to better adapt the energy source to the power plant.In discussing the several aspects of the change in approach from ""an engine and its fuel to a fuel and its engine"", the authors touch on the following areas:1. Description of an engine concept that provides the needed flexibility in fuel appetite at good efficiency to cope with future requirement s.2. The constraints placed on liquid fuel resource energy utilization efficiency by special engine-required fuel properties and the fuel efficiency of the various engine types available.3. Future vehicle engine fuel sources. This review will put into perspective the problem associated with the net energy available from future fuel sources under extensive research and development at present.4. A brief review of test data to show that fuel-tolerant and fuel-efficient engines are viable and that, in a fuel-resource-limited future, they can be a ""light at the end of the tunnel.""The Texaco Controlled Combustion System (TCCS)The TCCS is a unique means for stratified charge operation of an internal combustion engine in such a manner as to eliminate the requirement for octane or cetane number specification for the fuel. Octane rating is an empirical engine test method that evaluates a gasoline's resistance to spontaneous ignition or ""knock."" Cetane is based on a different engine test, which determines a diesel fuel's ease of spontaneous ignition . High cetane number enhances cold starting and permits high-speed diesel engine operation. As one would expect, the fuels in current use cover a band when the two values, octane and cetane, are plotted against each other."

Jan 1, 1982

By B. Jena, M. Rigaud, S. C. Panigrahy

"The influence of flux addition on the structure and properties of pellets produced from low silica specularite with peat moss and bentonite as binders was investigated. Specific pellets basicities in the range of 0.4 to 3.2 were obtained by the addition of limestone or a combination of dolomite and limestone as flux. A t basicities < 1.6, the bonding in the pellets was provided by a glassy silicate phase. At basicities =1.6, calcium ferrites were the predominant bonding phase. When dolomite was added as a flux, presence of magnesia-ferrite was noted. The reduction behaviour of pellets at different basicities was found to be influenced by the type of flux and binder. The pellet compression strength and swelling characteristics were improved with increased basicity.IntroductionThe properties of iron ore pellets are influenced by the type and nature of the ore or concentrate, additives and their subsequent treatment to produce pellets. The interaction between various constituents of the concentrate and additives, i.e. iron oxides, gangue and fluxes etc. result in the formation of various mineralogical phases which affect the degree and nature of bonding achieved in the pellet and the structure and distribution of pores. The pellet properties such as pellet strength and reducibility are influenced by the extent and type of bonding achieved between the ore particles. In view of the present emphasis on the production of high quality pellets to meet progressively stringent quality control requirements, it is essential to investigate the effect of additives on the bonding mechanism and properties of the pellets.In the past, the effects of additives on the bonding mechanism of pellets have been investigated. It is important to note that the conditions and parameters to be controlled are typical of a given concentrate/ore. In this paper, the results of the investigation on characterization of fluxed pellets produced from a low silica specularite concentrate are reported.This investigation was also aimed at assessing the suitability of peat moss for use as a binder for the production of low silica fluxed pellets. Peat moss is abundantly available in the vicinity of iron ore mines in Quebec and encouraging results have been obtained du ring the production of high silica acid and fluxed pellets."

Jan 1, 1992

By R. C. A. Thurston

Introduction A mechanical spring has been .defined by Wahl ( 1) as &apos;an elastic body whose ?primary function is? to deflect or distort under load, and which recovers its original shape when released after being distorted&apos;. Most material bodies are elastic to some extent ? and will deform under load, but they are seldom regarded as springs since this is not their primary function. The principal applications of springs are the absorption of energy and the mitigation of shock, the support cf moving masses or the isolation of vibration, and the provision or measurement of definite loads or torques. A large number of spring types have been developed to serve these purposes and to meet the different operational requirements; they range from the large semi-elliptic leaf suspension spring to the delicate watch hairspring. The springs of most importance in machine design, however, are the helical round-wire compression or tension types. They are made in a wide variety of sizes and are used in tremendous quantities, mainly because of their low cost, their compactness, and their relatively high efficiency. Their field of application is as broad as that of machine design itself, but the bulk of production is almost certainly for suspension systems of vehicles such as automobiles, freight and passenger cars, and mine cars, and it is with the last of these applications that this paper is primarily concerned.

Jan 1, 1951

By B. R. Neufeld, M. G. Heximer, S. J. Roach, W. G. Van Luven, D. G. Reynolds

"Teck Metals Ltd. operates an integrated zinc-lead complex at Trail, British Columbia, Canada. In the zinc plant, zinc concentrates are roasted to produce calcine, which is then processed in the leaching circuit for zinc recovery. Calcine is first dissolved at pH <2.0. This is followed by a precipitation stage using additional calcine that removes iron as a ferric hydroxide precipitate which is recycled to the lead operations. It is during this pH adjustment that impurities, notably arsenic, antimony and germanium, are co-precipitated with ferric hydroxide which is the primary removal phase for these elements. Recent processing conditions have resulted in lower iron inputs to the leaching circuit and this has resulted in insufficient co-precipitation of key impurities. This paper summarizes the influence of iron concentrations on impurity removal using laboratory and plant scale surveys, and emphasizes key specification limits for the primary iron removal circuit.INTRODUCTIONThe Sulphide Leach Plant (SLP) at Teck Metals Ltd., Trail Operations produces a zinc sulphate electrolyte from three different zinc bearing streams:1. Calcine, primarily containing zinc oxide, from the roasters2. Zinc electrolyte from the Oxide Leach Plant (OLP) is produced by leaching zinc oxide fume from the pyrometallurgical lead smelting operations3. Zinc slurry from the Zinc Pressure Leach (ZPL) autoclaveThe feed sources are blended and introduced to the iron removal process to precipitate iron in the form of a hydrolyzed iron precipitate which is recycled to the lead smelting operation. Along with iron, impurities, namely arsenic, antimony, germanium and silica, also co-precipitate; this process acts as the primary removal step for these elements. Following iron removal, the electrolyte is further processed in the zinc dust purification circuits. Cadmium and copper are removed in the cold stage circuit via zinc dust cementation, followed by cobalt cementation in the hot stage circuit."

Jan 1, 2016

By R. W. Lawrence, A. Bruynesteyn

"Pre-oxidation of refractory pyritic concentrates by biological leaching to enhance the recovery of gold and silver in cyan ideation has been investigated. The results of laboratory tests on three concentrates are presented. In all cases substantial increases in precious metal recoveries were obtained following the pre-treatment. For one concentrate, gold recovery of 81% was achieved following an 87% oxidation of pyrite, compared with 24% recovery by direct cyanidation of non-oxidized concentrate. Gold and silver recoveries from the other concentrates were increased from the range 60-78% to over 90% and from 80-86% to over 98% respectively. Operating parameters are discussed and methods of maintaining high oxidation rates are evaluated. Methods of employing this pre-oxidation technique in commercial practice are described.IntroductionMany of the gold and silver deposits now being developed contain precious metals finely disseminated in sulphide minerals such as pyrite. These ore s often present considerable resistance to metal recovery. The ease with which gold may be extracted is usually related to grain size and its manner of distribution within the host mineral. In many cases, a significant percentage of the gold may occur in submicroscopic form, or in solid solution with pyrite, so that even very fine grinding fail s to liberate the metal for recovery by cyanide leaching. Such ores are often termed refractory. Even in cases where liberation by fine grinding is practicable, high cyanide and lime consumption may be experienced due to the presence of specific sulphide minerals, and poor metal recovery may result.Pre-oxidation methods for refractory ore s and concentrates are commonly used to improve precious metal recoveries. Roasting, for example, as a pre-treatment to cyanidation, removes harmful constituents by oxidation or volatilization, and liberates gold from pyrite. In some cases, however, this method of pre-oxidation can result in poorer metal recovery, particularly of silver, due to fusion and the formation of clinker, and the formation of compounds which consume cyanide in the subsequent metal recovery stage. Difficulties in compliance with environmental pollution regulations may also be encountered."

Jan 1, 1983

By S. N. Dixon

"Maximizing the value of each tonne of processed ore is the goal for all operations. Cyanidation processing of gold-copper ores has been challenging since its first use in 1889. The current practice treats a bleed or the total flow of mill solution to recover copper as copper sulfide (by sulfidization, acidification, recycling, and thickening), or to recover the cyanide (by acidification-volatilizationneutralization). The process presented uses the adsorption of copper cyanide by carbon and the selective elution of copper from carbon to concentrate copper into a smaller stream. Copper contained in the smaller stream is precipitated as copper cyanide.RÉSUMÉ Toutes les exploitations ont pour objectif commun d’optimiser la valeur de chaque tonne de minerai traité. Depuis sa première utilisation en 1889, la méthode de traitement par cyanuration des minerais aurifère et cuprifère s’est révélée complexe. La pratique actuelle traite la saignée ou le débit total d’une solution de traitement du concentrateur pour récupérer le cuivre sous la forme de sulfure de cuivre (par sulfuration, acidification, recyclage et épaississement), ou pour récupérer le cyanure (par acidification, volatilisation et neutralisation). Le procédé présenté dans cet article utilise l’adsorption sur charbon actif de la solution de cyanure de cuivre et l’élution sélective du cuivre depuis le charbon pour concentrer le cuivre en un plus petit jet. Le cuivre contenu dans ce plus petit jet est précipité sous forme de cyanure de cuivre."

Jan 1, 2017

By Robert B. Parsons

"A joint federal/provincial/industry subcommittee of the Intergovernmental Working Group on the Mineral Industry (IOWG) has published an informative and readable report on taxation matters concerning Canada&apos;s mining industry. The report, which was presented to the federal and provincial mines ministers in September 1986, identifies and discusses key tax issues relating to this industry. The report is mandatory reading for anybody with an interest in mineral exploration or production in Canada.IntroductionIn 1986, Canada&apos;s federal and provincial mines ministers were presented with an important report concerning the taxation of this country&apos;s mining industry. This document is important for a number of reasons, two of the reasons being: first, the report contains an objective analysis of the key mineral taxation issues of the day; and, second, the report is the product of a cooperative exercise involving representatives of various facets of the industry and government. The report should be regarded as compulsory reading for anybody who has an interest in fiscal matters affecting mineral exploration and production.The ""Report on Fiscal Proposals"" was prepared by a subcommittee of the Intergovernmental Working Group on the Mineral Industry (IOWO). IOWO is a group of senior federal, provincial, and territorial government officials concerned with the analysis of mineral policy issues in Canada."

Jan 1, 1986

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed.The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grade, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the final cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure I."

Jan 1, 1995

By Peter A. Bevan

"In massive and semi-massive deposits, it is essential to take samples continuously for specific gravity determination as well as for assays of the various metals of interest. Failure to use specific gravity in mixed deposits of high density contrast will result in incorrect determinations of the average grade.Graphs and linear equations of specific gravity against the grade of one metal are not considered accurate enough in a multi-mineral deposit, but appear to be very satisfactory in a theoretical one-sulphide/gangue mix. Specific gravities based on base-metal values only in massive sulphide deposits will result in underestimating the effect of low grade areas on the average grade and also cause a reduction in the calculated tonnage.IntroductionBy definition, a base-metal assay is the percentage of metal by weight contained in a sample, whether it be a soil or silt sample, a grab, chip or channel sample, or a section of diamond drill core.In those cases where there is a series of contiguous samples, say in diamond-drill core, the average grade may be required of the various assays that are above a desired or required cutoff grade.Internal low grade or waste can be included if the assays one side or the other are used to ""carry"" the lower grade material and the resulting average grade is above the cut-off grade. To determine the average grade, the individual assays are ""weighted"" by multiplying these values by their respective lengths, adding up the cumulative assay times length and dividing by the total length. This method is essentially a weighting by volume, because the core diameter is constant and is common to all the samples being considered for estimating the average grade . If some of the core samples have much higher specific gravities than others, and the specific gravities are not used in the weighting process, the resultant average grade will be over-estimated or underestimated, depending on the grade of the heavier sections. When core assays of approximately the same specific gravity or weight are averaged by length, the error in the weighted estimation of the average grade is negligible."

Jan 1, 1993

By L. Hutton, S. W. Colley

"The release of soluble salts of base metals from acid mine pits and in the waste water from metal refiners is an avoidable source local pollution and contamination. Tightening of the regulations controlling natural resource extraction and industrial wastewater discharge is mandating the removal and recovery of metals from waste streams, and the remediation of contaminated sites. There is an economic incentive in recovering the valuable copper and nickel, as the value of the recovered metal can offset remediation costs and for high flow waste streams can be a source of income. Extraction of metals from waste streams by conventional Ion Exchange and chelation resins is widely practised, but has limitations on applicability in complex and dilute feeds due to the structure and properties of polymeric resin beads. Composite Advanced Ion Exchange (AIX) materials have been developed for the recovery and purification of base metals from base metal mining and metal processing industries. A silica-composite based resin has been developed for the selective extraction of copper from high iron containing feeds. This resin can be eluted with sulfuric acid yielding a copper stream suitable for return to solvent extraction or to electrowinning. We describe the development and application of the resin and process to two acid mine drain feeds of varying copper and iron concentrations, and show that the copper concentration can be considerably upgraded even at small scale with a final metal content of >95% copper.INTRODUCTIONWaste water with high sulphate concentrations, low pH and containing complex and variable mixtures of metals is an inevitable product in the mining, extraction and metal refining industries. One problematical water source is Acid Mine Drainage (AMD) which in addition to the metals of interest also contains a wide range of contaminating elements. Purge streams from metal refining are less complex in composition but contain significant quantities of the value metals. The typical treatment of such waste streams is treatment with lime to increase the pH of the water, precipitating the dissolved metals and sulphate as a sludge of mixed metal oxides/hydroxides and sulphates. The process is effective in producing a water stream that can be safely discharged but if there are significant concentrations of value metals such as copper, nickel, zinc then there can be a considerable loss of metal value."

Jan 1, 2016