Search Documents

By J. E. Flinn, S. A. Duran

The steady-state creep behavior of poly crystalline cad mi inn was studied over a temperature range of (1.56 to 0.94 Tm. Two distinct mechanisms were found to occur over this temperature range. They were described by: where and represerqt the minimum strain rates corresponding to the low- and high-temperature regions, respectirely. The two regions of constant acti11ation energy were connected by a transition region where the strain rate was controlled by both mechanisms acting in parallel. At temperatures below a transition temperature of about 0.7 Tm the agreement between the activation energy value for creep and that for self-diffiision suggests a rate-controlling mechanism of dislocation climb. For cadwzium, steady-state creep at temperatures above 0. 7 Tm appears to be controlled by another mechanism, perhaps involving the behavior of dislocation jogs. FRENKEL et al.1 studied the high-temperature creep of polycrystalline cadmium and reported an activation energy of 21 kcal per mole for the 0.5 Tm < T < 0.8 Tm range. Based on observations of creep rate at only two temperatures, a value of 22.1 kcal per mole was determined by Medbury. These two investigations were for the purpose of showing agreement between the activation energy for creep and that for self-diffusion, reported3 as 18.2 and 19.1 kcal per mole, respectively, for diffusion parallel and perpendicular to the hexagonal axis. Gilman4 investigated prismatic glide in single crystals of cadmium over a higher-temperature range of 0.72 to 0.93 Tm, and found an activation energy of 29 kcal per mole. He also reported5 an activation energy higher than that of self-diffusion for prismatic glide in zinc single crystals deformed at temperatures near the melting point. This value was in good agreement with those found for an equivalent temperature range by Flinn and Munson6 and by Tegart and sherby7 for polycrystalline zinc. These two independent studies also disclosed at lower temperatures another value of activation energy near that for self-diffusion. It would be expected from the creep results on zinc and single-crystal cadmium that creep studies on polycrystalline cadmium, extended to temperatures near the melting point, might yield an activation-energy value higher than the 22 kcal per mole value found in earlier studies. The purpose of this paper is to report the steady-creep behavior of polycrystalline cadmium over a temperature range of approximately 0.5 to 0.9 Tm EXPERIMENTAL METHOD The cadmium used in this study was obtained in the form of as-cast rods, 0.5 in. diam, through the courtesy of the Bunker Hill Mining Co. The material was of 99.995 pct purity, as determined by spectro-chemical analysis. The creep specimens, which were 0.250 in. diam by 0.400 in. long and annealed at 300°C for 45 min to produce a stable average grain diameter 0.25 mm, were tested in compression using an apparatus similar to that described by Sherby.8 The specimen temperature was controlled to within ±0.5°C with the help of appropriate constant-temperature baths. The applied stress was maintained within 1.0 pct of the desired value by the additions of lead shot at fixed strain increments. No barreling was observed over the strains encountered during testing. Isothermal creep tests9 were used in the study with only a few differential temperature tests10 run for comparison purposes. Steady-state creep data were obtained over a temperature range of 60 to 287°C (0.56 to 0.94 Tm) at five stress levels ranging from 28.1 to 140.6 kg per sq cm. RESULTS The minimum or steady-state creep rate may be described by an equation of the following form:" where i is the minimum strain rate, S is the structure factor, F is a stress function, Qc is the energy of activation, T is the absolute temperature, and R is the gas constant. The minimum strain rates obtained in this study for cadmium were recorded on a semilogarithm plot as a function of the reciprocal absolute temperatures for the various stress levels, as shown in Fig. 1. This figure shows a characteristic transitional behavior" with a parallel interaction of two mechanisms. It is obvious that the activation energies corresponding to the individual processes are insensitive to stress because the curves are parallel. The discrete activation-energies values for the low- and high-temperature regions for the various stress levels are reported in Table I, and were determined by the least-mean-square method. For the low-temperature region, an activation energy of 20.7 ± 0.6 kcal per mole was obtained, and for the

Jan 1, 1967

IN the early period of steelmaking, ingot structure and segregation were of no practical importance. Crucible melting required very small ingots that gave little segregation, and a small inserted hot top prevented pipe. As larger ingots were poured from bessemer converters and open-hearth furnaces, segrega- [ ] tion, piping, and gas evolution became increasingly important. The techniques of making semikilled and rimmed ingots were developed with little knowledge of the actual mechanism of the process. The first studies of solidification were made by the Brearleysl and Gathmann,2 who used stearine to show the effects of shrinkage and mold shape. Fig 11-1 is a picture of a series of stearine ingots at various stages of solidification. These studies showed that the liquid solidifies at a nearly uniform rate from the sides and bottom of the mold and demonstrated the formation of

Jan 1, 1951

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always have the same properties. The properties considered here, of course, are those inherent in the ingot immediately after solidification and not qualities imparted by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. Other variations in properties are due to variations in those constituents of steel (elements or compounds) that are not ordinarily included among the elements specified, thus not a part of the specified "composition." The term "constitution" is used to include not only the specified composition but also the nature and distribution of every element or compound contained in the steel entering the ingot mold ; also included are items such as aluminum oxides and nitrides, presence of soluble gases, and dispersion of nonmetallic particles. When it is considered that the constitution of steel is determined by the addition or absorption into the bath of all such constituents from whatever source, it follows that constitution is of necessity the final result of steelmaking practice. It is the agency through which steelmaking practice operates to control the properties of the steel. The term steelmaking practice is here used in the broad sense, meaning the control of all the materials entering the steel and of the conditions under which the process is carried out. Steelmaking practice, thus defined, establishes the chemical system within which the reactions between components must proceed in obedience to the laws of chemistry. Thus the chemical constitution of the steel is established and, through constitution, the properties of the metal are established. In the preceding chapters it has been shown how the constitu-

Jan 1, 1964

By Chas. Y. Clayton, Francis B. Foley, W. E. Remmers

DuRing the summer of 1919, the late Dr. Henry M. Howe, then Chairman of the Division of Engineering of the National Research Council, organized a committee to obtain a better insight into the behavior of carbon steels under the influence of various treatments by a proper control of the time and temperature factors. During part of 1919 and 1920, work in connection with this investigation was carried on at Dr. Howe&apos;s laboratory at Bedford Hills, N. Y. During 1921 there was an enforced hiatus in the work, occasioned by the illness which resulted in Dr. Howe&apos;s death in 1922. At that time one of the present authors compiled the results of the work which had been done and this was published in 1923.&apos; Following the publication of this work, it seemed desirable to carry on in the same manner an investigation of steel of C 0.75 per cent., which steel had not been as fully treated as had the other steels of C 0.34 and 0.52 per cent., used in the published work. Furthermore, certain unusual results have been obtained in the treatment of C 0.52 per cent. steel by quenching and drawing, and repetition of this part of the work seemed advisable. This has been done during the past year at the School of Mines and Metallurgy of the University of Missouri at Rolla, Mo., by a cooperative undertaking of the School and the Bureau of Mines, working in conjunction with the Committee on Heat Treatment of Carbon Steels of the National Research Council. The present paper is a report of the results obtained in this work.

Jan 1, 1926

By William E. Ford, Edward Salisbury Dana

34. Axial Ratio, Axial Plane. - The crystallographic axes have been defined (Art. 22) as certain lines, usually determined by the symmetry, which are used in the description of the faces of crystals, and in the determination of their position and angular inclination. . With these objects in view, certain lengths of these axes are assumed as units to which the occurring faces are referred.

Jan 1, 1922

By A. J. Goss, M. Tanenbaum, W. G. Pfann

THE purification of two metals, antimony and tin, by zone refining is described, and a reciprocating method of passing molten zones through a straight ingot, which effects a considerable economy of time and apparatus, is discussed. Antimony has been used extensively as a doping agent in germanium and silicon. More recently, it has become important in the preparation of new semiconducting compounds such as InSb, GaSb, and AlSb. High purity is especially necessary in this latter use, since the antimony may comprise as much as 80 pct by weight of the compound. Antimony is generally available in a commercial form of about 99.8 pct purity. Column 1 of Table I is a typical emission spectra analysis of commercially available 99.8 pct antimony. Zone refining has been quite successful in increasing the purity of such samples. Columns 2 to 4 of Table I are analyses of an ingot of the antimony of column 1 after the passage of seven molten zones in an atmosphere of nitrogen. The ingot length was 9 1/2 in.; the mean zone length was 2 in.; convection was the only means of stirring. The column headings are sample locations in inches from the leading end of the ingot. The results illustrate both the merit and a limitation of zone refining. It is seen that four of the five impurities—nickel, arsenic, lead,

Jan 1, 1955

By G. O. Hiers

THE object of the experiments reported in this paper is to determine the eutectic composition of copper and tin and to determine the location of the part of the liquidus line immediately above the eutectic composition in copper. Three methods were used in the investigation: (1) the method of dissolving copper in a bath of molten tin at constant temperature, with the idea that when the bath was saturated with copper its copper content, by analysis, together with the temperature at which the saturation took place would locate a point on the liquidus line (2) the method of the differential cooling curves, and (3) the method of microscopic examination. This paper is principally concerned with the results of the last two methods mentioned. The results of the first method, that of dissolving copper in molten tin, did not agree with the .results of Miller,1 by the same method, nor with the results of other investigators by other methods, nor yet with the results of the cooling-¬curve experiments and microscopic examination reported here.

Jan 1, 1929

By P. W. Barton, A. A. Johnson, E. J. Hughes

THE only systematic work on the effect of carbon on the recovery and recrystallization kinetics of iron so far reported in the literature is that of Venturello et al.1 These workers found that doping high-purity iron so that it contained up to 86 ppm C caused a marked retardation of recovery but had little or no effect on the recrystallization kinetics. Such evidence for an effect as was obtained was inconclusive. In the course of a study of electron-beam zone-refined iron the authors have recently examined the effect of added carbon on the recrystallization kinetics of this material. The amount of carbon added was about 50 pct more than was used by Venturello et 01. and definite evidence was obtained that carbon at this level retards recrystallization. The starting material was taken from a batch of 0.2-in.-diameter Johnson-Matthey spectroscopically pure iron rods which had been further purified by being given three passes at 4 in. hr-1 in a standard MRC electron-beam zone-refining unit. The purity of this material. which was used in two other investigations of the properties of high-purity iron,2,3 was established by an extensive series of analyses. Four laboratories, the National Research Corp., Newton, Mass., the Naval Research Laboratory, Washington, D.C.. the Battelle Memorial Institute, Columbus, Ohio, and the National Physical Laboratory. Teddington. Middlesex, England. carried out analyses for carbon. oxygen. and nitrogen. and in addition a complete mass-spectrograph analysis was carried out at Battelle. In all, twelve analyses were carried out for carbon, seventeen for oxygen and twelve for nitrogen. The amounts of these elements found to be present were 10 * 7, 8 i 5, and 0.9 i 0.1 ppm, respectively. The limits given are rms deviations. Two results, one of 46 ppm of oxygen and another of 31 ppm of nitrogen, were rejected as anomalous. The mass-spectrograph analysis revealed the major impurity to be 25 ppm of tungsten. All of the other elements detected were present in amounts less than 0.5 ppm. Some of the rods were doped with carbon by being immersed in a suspension of carbon in oil, heated in a vacuum at 400°C, and then zone-leveled to make the distribution of carbon uniform. Carbon analyses carried out on three of the doped rods gave a mean value of 130 ± 45 ppm. Some of the doped and undoped rods were deformed 58 pct by swaging and cut into specimens 1/2 in. in length. Isothermal recrystallization experiments were then carried out on them at 575", 600°, 615", 630°, and 650°C, the volume fraction of each specimen recrystallized being measured by a point-counting method described by Hilliard and Cahn.4 The results for the two types of specimens are shown separately in Figs. 1 and 2. In Fig. 3 the pairs of recrystallization curves for each temper-

Jan 1, 1965

By W. J. Taylor

The discussion on my paper entitled "Experiments with a Straight or No-bosh Furnace," read at the Philadelphia Meeting, September, 1884 (Transactions, vol. xiii., p. 489), suggests the propriety of slipplementing it with another, giving my views as to the cause of the failure, which was so decided as to create surprise among furnace men. As then stated, the Chester (8. J.) furnace, which had been 60 feet high, and 13 feet in diameter at the bosh, was altered to an 8-foot bosh, with a 7-foot hearth, 7-foot stock-line, and 4-foot bell,

Jan 1, 1886

By Avnulf Muan, Egil Aukrust

The activity-composition curve for cobalt oxide in (Co,Fe)304 solid solutions with spinel-type stmcture has been determined experimentally by studying the equilibrium between the spinel phase and a coexisting cobaltowüstite phase, "(Co,Fe)O", at 1200°C. A large negative deviation from ideal behavior prevails in the spinel at low cobalt oxide concentrations and a positive deviation at high cobalt oxide concentrations. The activity-composition curve for iron oxide in the solid solution is determined from the above curve by integvation of the Gibbs-Duhem equation along the join Co3O4,-Fe3O4. The standard free energy of formation of cobalt ferrite, CoFe2O4, from the oxide components CoO and Fe2O3 is calculated to be -8.2 kcal. ThERMODYNAMIC properties of (CO,Mn)3O4 solid solutions with spinel-type structure have been presented recently.&apos; The present paper deals with similar relations in another spinel solid-solution phase, that represented by the system Co3O4-Fe3O4. The principles involved in measurements and calculations of thermodynamic properties for the system Co3O4-Fe3O4 are analogous to those used and discussed in detail in the work on (CO,Mn)3O4. A (CO,Fe)3O4 solid solution coexists in equilibrium with a (Co.Fe)Ot solid solution over a considerable Here acOo1.33 and aao are the activities of cobalt oxide in the spinel and the oxide solid solutions, respectively, pO2, is the oxygen pressure of equilibration, and pb, is the oxygen pressure at which CoO and CosO4 coexist in equilibrium in the binary system Co-O at the same temperature. The activity-com position curve for cobalt oxide in the (Co,Fe)O solid solution in contact with metal has been determined in a previous investigation by the present authors.&apos; The system shows a small positive deviation from linear behavior. Because of the large defect concentration in wiistite and in (Co,Fe)O solid solutions, one cannot assume that the activity-composition relations in the oxide phase coexisting with a spinel phase at relatively high oxygen pressures are the same as those prevailing in the oxide solid solution coexisting with metal. However, a Gibbs-Duhem integration over the ternary Co-Fe-0 solution can be used to determine activities of cobalt and iron, and hence of CoO and FeO, from a knowledge of the oxygen potentials. Several papers have dealt with the subject of application of the Gibbs-Duhem equation to multi-component systems. 3-6 In the present case, it was

Jan 1, 1964

Paper withdrawn from publication September 8,1977, after book was printed. Pages 258.272 are therefore omitted.

Jan 1, 1977

By H. H. Stout

IN the early fall of 1025, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500° to 1600°F. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F." Smoot&apos;s reaction, after a few moments considera-tion, was, "It looks perfectly all right to me." The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after confer-ring as to ways and means, decided to go ahead with preliminary laboratory experi-ments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: I. Since brittle cathodes were often unin-tentionally produced, it seemed probable that the laws controlling this type of deposi-tion could be ascertained. 2. We had already proved the gas-clean-ing feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia Uni-versity for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrounded and heated by a resistance coil of Nichrome wire. Broken tough cathodes were used.

Jan 1, 1940

By George Langford

THE McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dikes of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compres-sive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed-an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magma that supplied the albitite dikes.

Jan 1, 1938

[Estimated Receipts Dues: Arrears $ 3,500.00 Current 108,115.00 New Members 11,937.00 In Advance 1,763.00 $125,315.00 Initiation Fees 7,250.00 Initiation Fees-Additional if increased to $20.00 7,250.00 Sale of Transactions....3,000.00 Sale of Binding 7,092.00 Sale of Magazine 2,913.00 Sale of Pamphlets 70.00 Sale of Indexes and Emmons Vols 313.00 Sale of Pyrometry 900.00 Sale of Raymond Vol 100.00 Interest received on Bank Balance 500.00 Interest received on Life Memberships 500.00 Advertising-Gross 27,000.00 Voluntary Subscriptions-Estimated 16,000.00 Income from James Douglas Fund 5,000.00 Total $203,503.00] [ ]

Jan 1, 1925

By W. E. Remmers

The defect in wire known as "cuppiness" has appeared and disappeared from time to time but the exact cause of its appearance or disappearance has not heretofore been known definitely. This defect is not limited to one particular metal or alloy but seems to be found at various times in all of the materials that are drawn into wire. Fig. 1 represents cuppy wire made from an aluminum alloy and Fig. 2 illustrates copper wire that became cuppy in drawing without intermediate annealing. Differences of opinion are current among the manufacturers of wire and in the literature (see bibliography at end of paper), some believing that the source of the trouble lies in segregation in the wire rod, oxides, sulfides, slag, etc.; others that the trouble is created by an unevenness of stress distribution across the section of the wire, usually thought of as being a function of die shape. All of the published work is of a qualitative rather than a quantitative nature. With this in mind, it was deemed advisable to make a study of the shape of the wire-drawing dies, as well as the oxygen content of the copper to be drawn. Experimental After several methods were tried, it was found that by studying the contour of the butt-end of the rod after drawing a measure of the "working" across the section of the wire could be made. The butt-end of the annealed rod was not sheared but was sawed off. The end was then smoothed with a fine file so that the plane of filing was perpendicular to the drawing axis. It is to be noted that this method is not an absolute measure of the distribution of cold working but is a very good indicative means of studying comparative values. The method of examining a tension break in wire was found to be the most sensitive in detecting cuppiness. Other methods, such as microscopic examination of longitudinal sections, X-ray radiographic studies, etching away of outer layers with nitric acid, and fracture by bending, can all be used to identify cuppy wire but the tension break will give the fracture characteristic of cuppiness before any of the other methods can

Jan 1, 1930

By Paul M. Tyler

MUCH information concerning pegmatites which was thought to be true a few years ago has been proved false, and what is now actually known about some pegmatites is not true of many others. The erratic and seemingly unpredictable structure and variable composition of this class of mineral deposits has been widely emphasized. Even parts of the same pegmatite body exhibit marked differences in texture, mineral composition, width, and attitude. Constructive geological thinking in respect to pegmatites now aims to establish general laws rather than to stress the confusing diversity of features having no special economic significance.

Jan 9, 1953

By R. E. Pray, M. C. Fuerstenau, J. D. Miller, B. F. Perinne

Quartz cannot be floated with potassium amyl xanthate as collector at any pH. Complete flotation is achieved with certain minimal additions of amyl xanthate and Pb from pH 5.8 to 8.5 and with amyl xanthate and Zn from pH 7.5 to 8.1. The active species of these metal ions responsible for activation are shown to be PbOH and ZnOH No flotation was effected when Cu and Mg were added as activators. Previous work1,2,3,4,5,6,7 has shown that quartz may be floated in the presence of sulfonate or soap when the following two criteria are met: 1) some portion of the added metal ion has hydro-lyzed to its first hydroxy complex, and 2) a precipitate of the metal-collector has formed. Since sulfonate and soap, two substantially different anionic collectors, conform to these criteria, this phenomenon may well be expected to be of a general nature. In this view then, it would appear that any anionic collector, including xanthates, should also float quartz when these two criteria are met. The object of this paper is to demonstrate the conditions under which quartz will respond to flotation in the presence of potassium amyl xanthate. EXPERIMENTAL MATERIALS AND TECHNIQUES Quartz was prepared by leaching the sized sample (48 x 150 mesh) with HC1 until no iron could be detected in the leach liquor. Conductivity water, made by passing distilled water through an ion exchange column, was used in the investigation. Potassium amyl xanthate was selected as collector. Purification of this reagent was effected with the following method: 1) a laboratory sample of potassium amyl xanthate was dissolved to saturation in hot ethyl alcohol and filtered several times while still hot, 2) the filtrate was cooled, during which time potassium amyl xanthate crystallized out of solution; the xanthate was then separated from the solution by filtration, 3) the amyl xanthate was dissolved in fresh hot ethyl alcohol and filtered, 4) step (2) was repeated, 5) the crystalline potassium amyl xanthate was washed with ethyl ether five times, and 6) the xanthate was dried for 24 hours under continuous vacuum. Inorganic impurities are insoluble in hot ethyl alcohol whereas dixanthogen is soluble in ethyl ether. Five-gram charges of 48x150 mesh quartz were conditioned for 3 min in 125 cc of solution containing the reagents and were floated with the small-scale cell and procedure described in previous papers.478 Reagent grade HCl and NaOH were used for pH adjustment, while reagent n-amyl alcohol was added as frother. Frother addition is necessary with this technique, but it should be mentioned that data, similar to those shown in Fig. 2 for 1 x10-4 mole per liter Pb++ and 1 X 10-4 mole per liter AX-, were also obtained with a Hallimond cell in the absence of frother. EXPERIMENTAL RESULTS Clean quartz could not be floated with amyl xanthate at any pH. Flotation was achieved under certain conditions, however, when various metal ions were added to the system. The activating ions used were lead, zinc, copper and magnesium, added as reagent grade chloride salts. Lead as Activator: The effect of Pb++ as activator was examined at five different additions of amyl xanthate (Fig. 1, 2 and 3). When 1x 10-5 mole per liter xanthate was added in the presence of 1 x 10"4 mole per liter Pb ++, no flotation was obtained at pH 6.5 or below, while a recovery of about 60% was effected at pH 7. When the pH was increased to 7.8, no flotation was again obtained, Complete depression was noted from pH 7.8 to about 10, at which point a recovery of about 30% was achieved. At about pH 11, the precipitate of lead amyl xanthate which was present below this pH dissolved and complete depression occurred. When 2.5x 10-5 mole per liter xanthate was added with the same lead addition, no flotation was obtained at pH 5.8 and below, whereas a recovery of

Jan 1, 1965

September 28, 1915. The Nominating Committee of the American Institute of Mining Engineers has the honor to present the following nominations for officers of the Institute to be voted for at the 1915 Annual Meeting: For President: L. D. Ricketts District 0 For Vice-Presidents: Karl Eilers District 0 James MacNaughton District 4 For Directors: Thomas B. Stearns District 7 Charles F. Rand District 0 Charles W. Goodale District 5 Edwin Ludlow District 2 George D. Barron District 0 F. W. BRADLEY, Chairman.

Jan 11, 1915

By William Laird

The predominent method of coal mining in the United States for years has been room-and-pillar mining. The reason for this has been the advantages of room-and- pillar method which is a relatively flexible system and its capital investment. The room-and-pillar method permits some selectivity in mining, especially where gas wells, faults and possible coal quality may be a factor. The mobility of continuous and conventional mining equipment used to develop entries may also be used for retreat mining of rooms and pillars. Longwall mining of coal takes place along a long straight face, or wall, blocked out between two butt or panel entries. The long faces or walls are normally projected in lengths of 61 to 183 m (200 to 600 ft) in this country. The longwall method of mining had its beginning in the United States during the 1800&apos;s. During that period, pack wall and wood posts were used for roof support. The longwall face was mined by miners using picks to undercut the coal. To keep the coal face from turning over, short wood posts called sprags were set in a slant position as the coal face was undercut to the depth of two to three feet. When the under-cutting cycle was completed, the sprags were removed to permit the coal to fall from the roof pressure. The longwall mining of coal did not take a firm hold during the 18009s, and room-and-pillar prevailed. In the early 19009s, steel jacks were introduced, and along with it, the modified caving theory. In March of 1950, a retreat longwall mining system, utilizing a plow, manually operated props, wood cribs and chock releases, was installed in one of Eastern Associated Coal Corp.&apos;s mines.

Jan 1, 1981

By F. E. Gregory

MINING methods and customs in many districts of England are to this day strangely bound about by the records and traditions of the past. In some mining fields this is more apparent than in others, yet it is everywhere in evidence, for Cornwall with her mines under the sea, Wales with her famous quartzites, and Derbyshire with her remarkable cavern deposits, are all tinctured with quaint customs that have come out of the almost forgotten past. Here, modernism has never replaced tradition, and many of the laws are woven of the woof and warp of ancient custom. Indeed, these things exist because they have come to be part and parcel of the civil laws. And these laws are observed with meticulous care and accorded all the reverence due their venerable age. All activities pertaining to the mining of metals are hedged around by curious and ofttimes clumsy laws, each minute and trivial detail being covered by the civil code, and each petty law enforced by an ofttimes pompous official.

Jan 1, 1933