Search Documents

By A. C. Maffei, M. V. Lins Gonçalves

Ore concentration processes are a function of the respective particle size distribution; however, most of them do not use an efficient operational method to determine it. From a practical point of view, the surface area can be calculated for any size analysis. The physical principles for determining the size distribution in each method are different, for the results will not be compared directly. During the development of the research project of the sulfide ore flotation method using inert gas, different methods for calculating the specific surface area have been used, such as sieving, sedimentation/X-ray, laser diffraction and BET, i.e. specific techniques to determine the specific surface area of copper and gold ore concentrates. The statistical method of minimum squares was used to achieve practical correlation equations among them. Regarding these two ores, if one knows a specific surface area value using one of the methods above, one can predict the result of the others. Diminution of the reagent consumption was so controlled and it could be even decreased by using inert gas.

Jan 1, 2003

Sluice box operating practices in Papua New Guinea (PNG), and published work on sluice boxes are briefly reviewed. Some recent work on sediment entrainment mechanisms occurring in sluice boxes have also been described. In the light of this information, some drawbacks in the commonly adopted sluice box operating practices in PNG, and ways of overcoming them, are also highlighted.

Jan 1, 1991

By Michael J. Kelly

IAMGOLD?s Westwood project is the site for the largest, by volume, bored vent raise in North America. When completed, it will be the fifth largest bored worldwide in a single pass. This paper will review the highest capacity raise drill system ever built (Redbore 100); as well as the technical difficulties in a single pass boring a 2,773 ft x 20 ft to 22 ft diameter raise. The difficult ground conditions and associated problems will be reviewed, as well as the solutions to overcome them. Use of the RVDS drilling tool to achieve .04% accuracy (14.5?) and the Geotube® water filtration system will also be covered.

Oct 1, 2010

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

By T. G. Joseph, K. Barron

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an “apparent friction” concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of triaxial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock. This strain-softening relationship is then applied to coal. Having determined the post-failure stress-strain curve for coal specimens, this information can then be used in a finite element program, such as Phase 2, to examine the post-failure characteristics of coal pillars. Using example data, the strength of coal pillars of different width/height ratios are estimated and compared with well-known empirical pillar size-strength relationships. In addition, the post-failure stress-strain behaviour of a coal pillar is compared with an empirical relationship reported in the literature.

Jan 1, 2003

By M. Li, J. D. Miller

Many technology problems must be solved if we are to continue to produce phosphate at our current rate of consumption. The U.S. produces at least 25% of the world's phosphate, 40 million tons of phosphate rock per annum with most of the production coming from Florida. Of particular concern are improved separation efficiency and the ability to treat new dolomitic resources. Phosphate flotation technology needs include: 1. Simplification of the standard flowsheet 2. Improved recovery of coarse phosphate 3. Selective flotation for phosphate recovery from dolomitic resources Preliminary results, including tests on plant feed from Florida show that these objectives may be achieved with a new collector chemistry depending on the specific circumstances. The effectiveness of the new collector chemistry has been demonstrated by the preliminary results from single stage flotation experiments both at the University of Utah laboratories and at Florida Institute of Phosphate Research (FIPR) laboratories. In the best case, from these experiments with low grade (5% P2O5) coarse feed (16x35 mesh), a single stage phosphate recovery of 95 % was achieved with a concentrate grade of 31 % P2O5. Such a separation efficiency could not be achieved using the traditional fatty acid/fuel oil collector. Based on these results it seems that a one step process may be possible for phosphate flotation and a research program is justified for the development of this new flotation strategy.

Jan 1, 2001

By B. Salt, R. Sullivan, E. Roos, M. de Vries, K. McKenna, L. R. Nelson, M. J. N. Uys, P. Jacobs, E. Munnik, P. Lewarne

A review is presented of the furnace cooling system design and operating developments since the initial furnace start up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators in particular to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement to operate this slag in a relatively highly superheated state (?T ? 400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomisation. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to Hatch high-intensity, water-cooled, copper Waffle coolers and tapblocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area) coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the Hatch Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

By J. Szlazak, A. Tor, M. Borowski, N. Szlazak, D. Obracaj

This article presents the analysis of ventilation systems used in dead-end headings, while being drilled, in coal mines. Special emphasis is put on methane and dust hazard. Mathematical model for distribution of methane concentration in a heading is given as well. This model takes into consideration sources of methane emission and change in air flow rate due to leaks in a duct line. Solving equations presented in this article enabled giving dependencies describing distribution of concentration along the heading. On the basis of these dependencies there is a possibility of determining places with higher methane concentration and ways of combating this hazard. Determining the distribution of methane concentration in dead-end headings ventilated by a separate ventilation system is of great importance as far as work safety conditions are concerned. The information obtained may be of use when finding proper places for installing methane sensors. Three kinds of separate ventilation systems were distinguished: forcing, exhaust and overlap. The development in construction of fans and spare parts of a duct line enables using both forcing and exhaust ventilation systems in headings developed by continuous miners, with length above 1000 m, in the conditions of methane, temperature and health-detriment dust hazards.

Jan 1, 2003

By Wenbo Lu

A combined method is present in this paper in analysis the dynamic stability of rock slope under the loading of blast induced seismic, in which, by combining the dynamic load calculating method of quasi-static method with the load inputting method of dynamic finite element method, such factors as the decay of seismic wave along its way of propagation, the frequency. amplitude. the phase difference of seismic wave, etc., can all be taken into account in analysis of the dynamic stability of slope.

Jan 1, 1999

Recent work on decoppering lead is reviewed CUS is formed rapidly even from dilute solutions of copper in lead. The mechanism of decoppering is discussed and an explanation for the retention of metals such as silver in lead is advanced. As decoppering tin appears to be an analogous process, the, Cu-Sn-S system is studied at 300°C.. CuS, which is not an equilibrium product, is found m decoppermg drosses. In the removal of nickel from lead, Ni3Pb2S2 is formed; preliminary measurements show the equilibrium nickel content to be greater than that obtained by stirring in sulphur. Decoppering bIsmuth IS thermodynamically favoured, but is complicated by the occurrence of CuBiS2 The Cu-Pb-S system IS the only one of the four studied where the equilibrium can be calculated simply, as the presence of ternary sulphIde or other phases invalidates calculations based on binary data.

Jan 1, 1971

By Jean-Marc Simard, Vincent Jourdain, Denis W. Roy

"Seven lithologic units, informally characterized, were recognized in the vicinity of the Montauban orebody. The first five lie in stratigraphic order. From structural bottom to structural top these are: (1) grey composite gneiss; (2) dark grey quartz-biotite gneiss; (3) quartz-biotite-garnet gneiss hosting several calcareous, aluminous and magnesian members and gold mineralization; (4) light grey quartz-muscovite-(sericite)-biotite gneiss; and (5) metabasafts. The last two intrude the sequence: (6) amphibolite dykes and (7) pegmatite veins. The orebody lies on the inverted limb of an overturned synform verging to the west with the metabasafts marking the core of the fold. As the foliation is folded, this fold is attributed to deformation ""D2""; deformation ""DI"" being responsible for the formation of the foliation. A late brittle deformation developed shear zones with probable strike-slip motions. The refined stratigraphy and the identification of the structural position of the orebody provide new tools for regional interpretation and prospecting.RESUMESept unités lithologiques ont été définies informeffement à proximité du gisement de Montauban. Les cinq premieres reposent en ordre stratigraphique; ce sont de la base au sommet structural: (1) le ""gneiss mixte gris""; (2) le gneiss gris forcé à quartz biotite; (3) le gneiss a quartz-biotite-grenat comprenant plusieurs membres calcareux, alumineux et magnésiens ainsi que la minéralisation aurifère; (4) le gneiss gris clair à quartz muscovite- Isericitel-biotite; et (5) les métabasaltes. Les deux autres unites sont intrusives dans la sequence: (6) les dykes d ‘amphibolite et (7) les veines de pegmatite. Le gisement se sitlie sur le flanc inverse d'un synforme déverse vers I' ouest dont les métabasaltes occuperaient le cœur. Comm e la foliation est plissée, ce pli est considère appartenir d la deformation ""D2""; la deformat ion ""DI"" etant responsable de la formation de lafoliation. Une deformation cassante tardive se traduit par des zones de cisaillement, d rejet apparemment directionnel. Cette stratigraphie plus précisé et l'indentification de la position structurale du gisement fournissent de nouveaux omits de prospection et d'interprétation regionalé."

Jan 1, 1987

By Urie R. W

Fluidized bed roasting of copper concentrates from Mt. Morgan, Mt. Lyell, Mt. Isa, and Peko was performed in a 3 ft 6 in diameter, slurry fed, pilot plant roaster operated under autogenous conditions to produce calcines with desirable leaching properties. A 12 in. diameter, externally heated roaster, provided with a dry feed system, was also used.An account is given of important factors which influence roaster behaviour and performance, and the effects of operating variables on calcine composition and leaching properties are described. Due to copper ferrite formation, a maximum of approximately 50 per cent of the copper in the calcines may be in the form of CuO before the copper leach efficiency falls significantly below lOO' per cent. Recovery of gold by cyanidation of leach residues was consistently high and independent of roasting conditions.INTRODUCTIONIn traditional practice copper is produced by pyrometallurgical techniques when the ,copper minerals in the ore or concentrate are predominantly sulphides, and by hydrometallurgy when the minerals are oxidized. Copper smelting is most suited to large scale operations, and for many years small to medium size mines with sulphide orebodies have been interested ill; alternative processes.Since hydrometallurgical plants (ie. leaching and electrowinning plants) are essentially unitized, they may be scaled down in output without much loss in efficiency or increase in processing cost, and many proposals have been made for the application of this type of process following roasting of the sulphides to render the copper soluble. However, until the advent of fluidized roasting, it was not possible to control the roasting operations sufficiently precisely to produce calcines consistently of the required leaching characteristics.

Jan 1, 1961

By Wang Hong Qu

This paper observes the shape of throw explosion crater its ejecta locus of internal medium and the process of distance along with slope's angle developing. It was discovered that initial velocity is inversely proportional to slope's angle. The velocity of surface distribution at the lower half crater of explosion is larger than at upper one. It carries the relevant calculated formula and physical process of explosion crater forming under the inclined boundary conditions, and some important law. It proved that the gravity influence is very distinct for the blast action in the little resistance line.

Jan 1, 1991

By K. G. Correia

The replacement of the dry mining method at Guajú Mine by the dredging method was a means of ensuring its feasibility by maintaining the production levels. Dry mining increased the cost of the deposit with the distance and presented a limited mined volume, while the decreasing grade of the deposit led to a production drop. With the new methodology, there was a considerable reduction in unit cost of the mine and an increase in the production level of a deposit with low heavy minerals content.

Jan 1, 2005

The Golden Cross project was a joint venture between Coeur NZ Ltd (80 per cent) and Viking Mining Company (20 per cent). The site is located in the Waitekauri Valley, 8 km north-west of Waihi, on the Coromandel Peninsula, in the North Island. The mine-site is situated close to the Coromandel Range Divide between the headwaters of the Waitekauri River and the Martoto Stream. The site has a history of Gold Mining dating back to 1892. The more recent mine comprised an open pit and underground gold and silver operation from December 1991 to April 1998, MacGillivray, Maton and Goldstone (2000).Doug Hood Ltd commenced the first of three contracts on site in September 1997 and was responsible for completing the final stages of open pit mining, landslide remedial works mine closure and rehabilitation works. The Mill Closure and Rehabilitation and Drainage Works contract, for which this submission relates, commenced in September 1999 and was officially completed by Doug Hood Ltd. on the 26 May 2001.This paper endeavours to highlight the project objectives and backgrounds them against the difficulties experienced with respect to the site-specific conditions, the design complexities and risks associated with the contract, from a contractorÆs perspective.

Jan 1, 2002

In addressing the need for non-degree tertiary training, let us examine some recent reviews of engineering and geoscience education. The Finniston Report (1) criticised the formation of engineers in the UK and stated that this was largely due to the narrow British conception of engineering as a branch of applied science which militates against an effective marriage between theory and application. It also criticised the system for not giving students sufficient grounding in the synthesis of technical, human and financial considerations within their undergraduate courses. As we all know, this report has led to the restructuring of engineering education in the UK. More recently, a Review of the Discipline of Engineering was carried out in Australia by a committee chaired by Professor Sir Bruce Williams (2). The report stated that: Australia has a fairly good system of engineering education that should be made better. more should be done to develop the communication skills of both staff and students. more attention should be paid to changes in engineering practice and the human element in technology. there is a serious shortage of state of the art equipment in most engineering schools. female enrolments in engineering courses should be increased from the current level of about 7% to 20% by 1997. employers should develop a better understanding of the need for continuing education. staff in engineering schools should develop closer relations with employers of engineers. higher education institutions with engineering schools should give financial and other inducements to staff to increase the proportion of study leave or professional development leave spent working as engineers in the business sector. there is considerable room for improvements in the teaching process and in the development of evaluation schemes for assessing the teaching contributions of staff. In its recent report to the Council of the Institution of Engineers, Australia, the Task Force on Engineering Education(3) makes the following points: managerial, entrepreneurial, professional and interpersonal skills should be introduced and integrated into the undergraduate courses but studied in depth as part of continuing education. the continuing education policy of the Institution should be promoted and strengthened with all engineers required to pursue continuing education. the Institution should develop a comprehensive guide to continuing education available from universities, colleges and other public and private sector organisations.

Jan 1, 1989

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By Mathew Janes

"Sheet piles remain an economic solution to many shoring problems. However, installation of sheet piling suffers high noise and vibration with conventional impact or vibratory methods or low production and high expense with push techniques. Many projects simply will not allow sheet piling due to vibration concerns.Installing sheet piles with a tunable, high frequency Resonant vibrator provides high production with imperceptible ground vibrations. Recent projects in Canada have proven the technique on production projects where vibration sensitive structures are present immediately adjacent to the sheet piling. A project in Whitehorse, Yukon required a Waterloo style impervious sheet pile barrier be driven immediately adjacent to a sensitive, large diameter sewer line. The 1800 m2 Waterloo barrier was driven to prevent hydrocarbon leachate from entering the Yukon River. Proposed driving of the sheet raised concerned as the sewer serviced downtown Whitehorse. Monitoring of the sewer during Resonant driving proved the ground vibrations to be imperceptible. Use of the Resonant Driver prevented all concern over ground borne vibration of the sewer and allowed the contractor to progress at conventional, high production while maintaining low cost to the owner.Subsequent projects continue to prove that Resonant driving of sheet piles achieves high production while eliminating ground vibration.IntroductionA complex environmental clean-up problem required a unique solution. A historic oil and fuel transfer station in Whitehorse, Yukon is located on the Yukon River. The facility has been in use since the Second World War and witnessed much careless activity. The sand and gravel site provided ease of transmission of hydrocarbon leachates directly into the Yukon River. Continued use of the site required a barrier wall be constructed to prevent hydrocarbon from leaching into the Yukon River. A short construction season and restrictive fisheries window made for a compressed schedule. Along the shoreline of the property and within the required clean up zone a large diameter sanitary sewer collector line was present that serviced the majority of downtown Whitehorse. The design called for a barrier wall to be constructed along the waterfront adjacent to the sewer with cofferdams constructed out into the Yukon River to recover contaminated riverbed soils. The coarse sands and gravels meant high hydraulic conductivity into any kind of excavation, including slurried or drilled shafts that may have been used to construct a low vibration shoring system. Conventional hammer or vibrator technology would result in high ground vibrations that risked damaging the sewer. The Resonant Driver method was selected for its ability to drive sheet piles with high production and zero ground borne vibrations."

Jan 1, 2014

Bioleaching of E-Wastes

Sep 13, 2010

By V L. Los, G J. Abramson

The paper examines three types of polar zoning of ore-forming and associated elements that can be detected from geochemical data. Polar zoning is mapped in the form of geochemical ore systems of various ranks. Various types of polar zoning can be found in some systems, which present a general geochemical model of the ore object. The genetic basis of zoning is examined from the perspective of the conception of geoelectrochemical redistribution of matter, including ore-forming elements. The volume of the geochemical ore system may be used in the prognosis of resources for every rank.

Jan 1, 1999