Search Documents

By S. M. Shelton

Tests employing various ore-dressing methods were made on a manganese wad ore from the W. A. Chinn property in the Batesville-Cushman district of Arkansas in an effort to develop a practicable procedure for the production of ferromanganese-grade concentrates. The ore body occurs as a bed approximately 7 feet thick in the residual clay of the Ferndale limestone formation5/. The crude wad ores are soft aggregates of various oxides of manganese, which are loosely bonded together. Hard lumps of high-grade ore are disseminated throughout the wad. Hausmannite, pyrolusite, and psilomelane are the principal minerals. Some clay is present, but most of the gangue consists of leached fragments of the original siliceous and calcareous rocks in which the manganese occurred. In addition, hydrated oxides of iron, which axe present, also must be considered as gangue. Definite phosphate minerals have not been identified.

Jan 1, 1942

By Richard L. Fowler

An automatic steering control system was designed, installed and tested on a coal mine shuttle car. The system utilizes sensors and associated signal processing electronics developed under a previous phase of this contract. The automatic steering system performs the routine guidance functions of turning corners and straight-through tramming. The shuttle car driver retains full authority of speed, braking, load and unload functions and at any time may exercise his option with manual override or steering. Steering information is generated from signals derived from the existing Lateral Guidance sensor subsystem, and all operational features of the previously developed open-loop system are retained. Above ground system tests were conducted in a simulated mine constructed of wood panel ribs. Results were in good agreement with prior hybrid computer simulations undertaken to validate the basic control system over a broad range of conditions and to select system parameter values. The automatic steering system was successfully demonstrated in the above ground simulated mine to USBM technical representatives. Designed to meet USBM permissibility requirements, the system is ready for a Phase II underground testing program. Testing in actual underground mine environment is expected to provide additional data regarding recommended performance improvements and implementation techniques.

Jan 1, 1975

By D. J. Pandelis, W. J. Schlittler

Auxiliary Equipment pumping systems to support primary, secondary and regrind grinding circuits will be the primary focus of this paper. Every grinding system is unique and requires special design considerations for proper application of pumps to transport mill discharge. To satisfy the majority of applications, a new series of pumps has been developed by Svedala, known as World Class Pumps. Selection of these newly developed pumps for each type of grinding circuit will be presented. Specific components of selection are materials of construction, piping system, classification method, material characteristics and slurry characteristics. Both horizontal and vertical pump applications will be reviewed with emphasis on rules of pump piping and sump design.

Jan 1, 1999

By R. L. Balmer

This information circular, which describes the methods and costs of sinking a small underground shaft with steel supports at the Keystone mine of American Smelting and Refining Co., near Crested Butte, Colo., is one of a series being prepared by the Bureau of Mines on current shaft-sinking practices in various mining districts of the United States. Preparations for sinking a combined exploration, development, and production shaft from the lowest level of the Keystone mine began early in 1957. This vertical, three-compartment, 6-1/4-by 16-foot rectangular shaft was to be sunk in separate stages or lifts so as to correspond with the progress of an associated lateral exploration and development program. The first section of the shaft was collared and sunk to a depth of 209 feet between September 1957 and April 1958. Because of the depressed base-metal market, the mine was shut down as soon as the initial phase of the exploration and development program had been completed and before any deeper sinking could be attempted.

Jan 1, 1962

By Frank G. Horino

This report presents a method of utilizing the Coulomb strength criteria for estimating the strength and stability of pillars and pit slopes containing planes of weakness. It is assumed that the Coulomb theory, as a special case of the Mohr envelope, is a satisfactory first approximation of failure in uniaxial compression or triaxial loading with low lateral loads. Accepting this assumption for brittle materials, an expression for the strength decrease of rock pillars containing a plane of weakness or fracture at any angle of orientation is derived. As few as six samples (three solid cores and three fractured cores at a failure-oriented angle) are required for testing uniaxially and triaxially to statistically determine the coefficients of friction and the shear strengths of both the solid rock and the fracture plane and the range of failure angles of the fracture plane. Interpretation of the data shows that the mean normal stress and maximum shear stress technique of analyzing the data is superior for solid core and that shear and normal stress values using angles of failure should be used for fractured specimens with failure-oriented angles. Plots of either the strength or strength ratios against fracture angles obtained from oriented drill core samples give a useful first approximation of strength decrease due to fracture. Using the same test conditions for both fractured and unfractured material increases the validity of the tests.

Jan 1, 1970

By C. W. Owings

One phase of Bureau of Mines health and safety work is promotion of the use of safe and effective dust-collecting devices in connection with rock drilling in coal mines. To insure that adequate equipment of this type is available to the coal-mining industry, the Bureau of Mines conducts investigations and issues approvals for dust-collecting equipment that meets the requirements of a schedule established for testing dust collectors intended for use in connection with roof drilling for roof bolting and for other rock drilling. 6/ Performance tests are conducted under the provisions of this schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for approval and lists drill-dust collectors that have been granted approval as of January 31, 1956. The addresses of manufacturers of approved devices are listed alphabetically at the end of this circular.

Jan 1, 1956

By Etienne Audibert

No satisfactory theory has yet been advanced to explain what takes place when an explosive is fired in a mixture of firedamp and air. The only means of measuring the' danger is to fire the explosive into the gas mixture and note the effect, but the conditions of firing must be chosen carefully. This report is presented in the hope that it will assist in determining what method to use. The experiments have been designed to show the effect of the principal factors involved in the conditions of firing, and the results give information that seems to have some value.

Jan 1, 1940

By Etienne Audibert

No satisfactory theory has yet been advanced to explain what takes place when an explosive is fired in a mixture of firedamp and air. The only means of measuring the danger is to fire the explosive into the gas mixture and note the effect, but the conditions of firing must be chosen carefully. This report is presented in the hope that it will assist in determining what method to use. The experiments have been designed to show the effect of the principal factors involved in the conditions of firing, and the results give information that seems to have some value.

Jan 1, 1940

By Bernard Baum

Combined preservative/fire retardant systems were pressure impregnated into Douglas fir and Ponderosa pine samples and evaluated for decay, flammability, and mechanical properties. The objective of the evaluation was to identify cost-effective systems for use with mine timber, and to provide an information and data base from which Federal code regulations could be established. Thirty systems, based on combinations of commercially available preservatives and fire retardant impregnants and coatings, were applied to Douglas fir samples and evaluated for decay and flammability. The ten most promising systems were ap¬plied to both fir and pine and reevaluated for decay and flammability before and after water leaching. The five best systems were given a thorough laboratory evaluation using both pine and fir. Evaluations included flame spread, smoke density, toxic gases, decay, compressive strength, flammability after artificial weathering, and cost. All systems had acceptable toxic gas levels and smoke densities, but flame spread was only borderline acceptable for most of the samples tested. A trade-off analysis showed Acid Copper Chromate/Fyrprufe with Albi-107A/144 intumescent paint and Koppers NCX to be the-best systems. Recommendations are made for further large-scale testing using the two best Systems.

Jan 1, 1978

By M. Sagheer

An 8.5-km (5-mile) conveyor has gone into operation in western Turkey to eco¬nomically transport crushed lignite from the mine area to a power plant. This conveyor has replaced trucks as the principal mode of transporting the lignite. One principal element of Turkish govern¬ment policy is the country's commitment to increase electricity supplies for mining and other industries. Lignite is an important source of electric power supply in Turkey. Production was about 48 Mt (53 million st) in 1987, amounting to more than 20% of the total power supply in Turkey. In the western Anatolia supply network, it plays a major role for power generation. Deposits are located in the Soma region of western Turkey. The lignite is of low quality, deposits are scattered, and the terrain is dif¬ficult and hilly. These conditions demand an economical and technically feasible method of transporting the raw material from mining areas to the central thermal power plant. The Soma power plant is located about 120 km (75 miles) northeast of Izmir, near the coast of Aegean Sea. An overland conveyor of a unique design has gone into commercial operation at the Soma power plant facilities of the Turkish state electricity organization, Türkiye El¬ektrik Kurumu (TEK). The conveyor re¬places truck transport to ensure economical use of the lignite deposits. Computer-aided design (CAD) added more precision, qual¬ity, and flexibility of engineering in design activities. It also helped quick realization of the project that was executed in cooperation with the German company Krupp Industri¬etechnik and the Turkish firm Gama Endüstri AS. Unique features The conveyor includes several major features rarely combined in a single flight: Overland long distance conveyor. • Horizontal curves. -Steep vertical concave and convex curves to match the difficult terrain. Down-hill conveying. Frequency converter drives with vari¬ able belt speed. Generating operation mode to backfeed the energy to the network. Layout The 8.5 km (5 mile) long conveyor takes the -200 mm (-8 in.) lignite from the primary crushing plant located near the mine to the central, final crushing plant located in the stockyard area near the power station. The drive and belt tensioning assemblies are situated near the tail end of the flight. The high voltage switchgear is housed in a room in the primary crushing plant build¬ing upstream from the conveyor flight. The frequency converters are installed in the low voltage switchgear room located below the control room within the primary crushing plant building. Conveyor design The conveyor includes two 4 km (13,120 ft) radius horizontal curves, one left-hand and the other right-hand. The minimum radii

Jan 1, 1989

By William R. Wessels

This report describes a field survey and laboratory investigation into the causes of failure of resiliently clad screen decks applied to coal preparation plants. Blinding of screen deck perforations and delamination of the resilient cladding are studied and mechanisms responsible for these failure modes are hypothesized. A laboratory test program to simulate the mechanisms was begun and abandoned when it became apparent that meaningful test results would require a substantially redirected effort. No meaningful test data was obtained from the laboratory simulation.

Jan 1, 1982

By S. M. Shelton

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well-known that there are largo deposits of low-grade ore in the United States, production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stock piled ore is depleted through inability to obtain adequate supplies from foreign sources. Consequently, a program of laboratory and pilot-plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines. This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series, Report of Investigations 3506, Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent, and C. H. Schack. Other reports will be published as the work progresses.

Jan 1, 1942

By J. S. Bays

Industries are challenged to meet increasingly stringent regulations for selenium and metals. Cost-effective treatment is required to minimize the economic impact of environmental compliance. Low-cost biological treatment of selenium can be achieved passively using biochemical reactor cells composed of natural organic media components such as wood chips, sawdust, hay, composted manure, and peat. The reactor cells create an anaerobic microenvironment for biological reduction and sequestration of selenium and other metals. Biochemical reactors can be combined with constructed wetlands for flow equalization and to remove the organic byproducts in reactor cell outflow. Passive treatment reduces capital cost and operational effort compared to more expensive and complex physical and chemical treatment. Recent pilot and full-scale projects by mining companies and by the US Bureau of Reclamation demonstrate that passive treatment can achieve compliance with selenium concentrations over a range of flows and environmental conditions. Case histories of passive selenium treatment systems and their key findings are provided, and prospects for future applications are summarized.

Feb 27, 2013

Productivity in underground metal and nonmetal mines is contingent upon work methods, mine layout, and ore handling techniques. One of the most important factors impacting productivity is the efficient movement of men, materials and supplies from the surface into and throughout the mine. Various transportation systems such as man-trains, service shafts, rubber-tired diesel equipment, etc. are currently used to transport men and supplies in underground mines. In many underground mines, it is not uncommon for a worker to spend 25% of his eight-hour working day traveling from the surface to his work area and returning to the surface.

Jan 1, 1975

Coal mining in New Zealand is principally a State-owned and controlled operation where the State produces 70 per cent of the coal in New Zealand and 65 per cent of coal mined in the Waikato. The State's flexibility in production quality and price makes them tough competition. Coal in the Waikato varies in quality considerably throughout the region making the high quality coal deposits as in the Huntly district a highly sought after commodity. The high quality of coal is often offset against transport costs as, for example, Maramarua coals can compete effectively in the Auckland market and dollar per calorific value basis.

Jan 1, 1984

Atlas Copco Construction and Mining Australia identified a number of issues in regard to the skill levels, labour turnover and productivity of our service technicians. In 1994 we were experiencing a labour turnover rate of 42 per cent per annum amongst our technicians. Exit interviews were held with each individual and one of the major areas of dissatisfaction was the degree of product training provided on our equipment, compared to what is required to be competent across the range of our products. These tradespersons were prepared to accept the reduced remuneration that an OEM offers, for the benefit of comprehensive, professional training that, in theory, could be provided. The truth is that we were achieving approximately 40 per cent of our target for training hours because of the demands of field service, pre-deliveries, etc. So, the summary was the same as the industry was experiencing at that time because of skilled labour shortages, production demands, etc people were employed and thrown in at the deep end. A recipe for failure that will be successful every time.

Jan 1, 1998

By L. J. Barnes

The process for bio-remediation of sulphidic slag (BROSS) operates at 45 degrees C in a neutral (pH 7), aerobic aqueous environment in which sulphide in the slag is converted to sulphate. A two-stage version has been developed that involves quantitative chemical pre-oxidation of total sulphide to thiosulphate, followed by complete biooxidation of thiosulphate to sulphate. Ferric hydroxide, also produced, acts as a flocculant in the bioreactor effluent, concentrating heavy metal precipitates in the thickener as a sludge which can be returned to the smelter. The process has a high sulphate production rate and low acid and nutrient consumptions. Microorganism growth is the rate-limiting stage, requiring a minimum liquid residence time in the bioreactor of about 7 h. Although large quantities of oxygen are needed, sufficient gas mass transfer can be attained in an air-lift reactor. Products are an aqueous stream containing sodium sulphate with only trace levels of toxic heavy metals and a benign, toxic metal-containing sludge

Jun 18, 1905

By I. V. Lunkin, E. B. Muhamedzhanov, A. B. Begalinov, B. R. Rakishev

Almost all the ore deposits of ferrous, non-ferrous and rare metals of Kazakstan, are exploiting by the open-cast method, are the complex-structural, multi-component ones. Their rational working requires precise organization of extracting works. In this connection it is necessary to set up the best intercommunications between drilling-blasting, excavating-loading and transport works. This requires the stable functioning of the quarry for dispatch of ore raw material of required quality with minimum of corresponding expenses. For this purpose, proceeding from the quarry’s ore output and the assumed parameters of the exploitation system, the first problem about rational arrangement of excavating-loading equipment in extracting faces is solved. By solving the problem the model with dynamic, adapting properties had been used. It was solved numerically by the method of statistical tests. By setting up the necessary link between type-sizes of excavating-loading and transport equipment, the minimum prime cost of loading and transportation of 1 ton of mining mass from the face to the receiving station was adopted as the criterion of optimality. Depending on the type of excavating-loading equipment, the efficiency function may be different. By using wheel loaders, their displacement between the faces is possible, therefore, the efficiency function of the problem may include expenses for their displacement. By using excavators like power shovel, the problem’s restrictions must exclude its displacement between the faces. The efficiency function consists of minimum expenses for loading, proceeding from set of volumes of extraction from the faces, satisfying required quality. The volumes of extraction from the faces, satisfying required quality of ore in output stream, are determined by the method of statistical tests. Sample range is given, proceeding from the restrictions for maximum productivity of the excavating-loading equipment. Volumes of extraction, not satisfying required quality, are cut off. The efficiency function meaning is then determined and minimized. Keywords: Excavating-loading equipment, its placing in extracting faces, optimal load-carrying capacity, specific expenses for loading and transportation of mining mass.

Jan 1, 2003

By B. M. England, C. Y. Yang, L. T. Matthews, J. Y. Yin

The domestic concentrate used by the Shanghai Meishan Metallurgical Corporation in Nanjing contains significant siderite, magnetite and haematite, the siderite having a substantial influence on its sintering behaviour. On the basis of experimental findings and published information it is proposed that siderite decomposition starts at c.400 degrees C and results in the formation of CO and/or H2, which then reduces the haematite to magnetite prior to the initiation of high-temperature sintering; inter-mixed particles of Australian haematite and pisolite ores also undergo significant reduction. As the gaseous reduction process is so effective, low-temperature forms of silico-ferrite of Ca and Al (SFCA) cannot form even at high sinter basicity. The bench-scale results were confirmed in a pilot-scale facility whose sinters consisted mainly of magnetite, high-temperature SFCA and glass, which is typical of sinters formed from mixes with high magnetite levels

Aug 1, 1995

By Joseph M. Kurtak

The Bureau of Mines is currently conducting a four year mineral assessment of the 5.7 million acre Valdez Creek Mining District in Southcentral Alaska, as part of its ongoing statewide mining district evaluation program. This report is a summary of the 1987 field work, which included the examination of mines, prospects, and mineral occurrences in the study area. Placer gold has been the most important metal produced in the area, and production totaled 161,131 oz, with the majority of the production coming from the Valdez Creek Mine. Lode gold and silver production totaled 1,581 oz and 8,617 oz, respectively and came mainly from the Golden Zone Mine. Varying amounts of other metals, including copper, lead, zinc, molybdenum, antimony, chrome, nickel, cobalt, tin, tungsten and platinum exist in the study area. Occurrences of industrial limestone and coal are also located in the area.

Jan 1, 2011