Search Documents

By G. T. Hong

A numerical model for use in design is developed to predict the stresses and axial and bending displacements in a drilled pier in expansive soils. The prediction is based on the horizontal swelling pressures and uplift forces which act on the side of the drilled pier. The exponential suction envelope with the depth within the moisture active zone is estimated based upon the equilibrium suction, moisture diffusion coefficients obtained from laboratory tests, and minimum suction at the ground surface of the site based on field conditions. The volume change of soil is based on suction variations, soil properties, overburden pressures, crack influences, and the relationship between moisture contents and suctions. Considering the movement active and anchor zones on a soil-pile system in expansive soils, horizontal swelling pressures are formulated using the shear strength of an unsaturated soil and the Mohr?s circle and failure envelope. The movement active zone has two sub-zones in which horizontal swelling pressures are attributed to passive earth pressure failure and suction change in the upper and lower sub-zones, respectively. Horizontal swelling pressures which occur in the anchor zone are assumed to be in the at rest condition. The shear stress generated on the vertical surface of a drilled pier is supported by the nonlinear curves of load transfer versus relative displacement. The axial behavior and lateral bending of the pier in expansive soils are simulated using a beam column approach. The computed axial and bending displacements and stresses are used to provide structural design of the pier. Figures of computed results for typical cases are presented.

Jan 1, 2007

By Roger "Dean" Skaggs

Mechanical rock drilling is about 150 years old, and the fundamental principles of augering, penetration and dragging, pressure and rotation, and percussion have not appreciably changed. Surface mining blasthole drilling employs relatively shallow blastholes (to about 100 to 130 feet or 30 to 40 meters) with respect to the blasthole diameter and hole alignment while problematical is not a major universal problem. Modem underground mining methods are spacing development levels up to 400 feet (130 meters) apart, to take advantage of high powered mechanical drilling methods, requiring very long blastholes compared with surface mining. Blasthole alignment is a major problem in underground mining and this paper will address the aspects of percussion bit design which impact on hole alignment and drilling and blasting costs, i.e. bit geometry, cuttings removal, penetration-retraction.

Jan 1, 1997

By Ali Kahriman, Abdulkadir Karadogan, Deniz Adiquzel, Umit Ozer, Suat Bicer, Mehmet Aksoy

This paper presents the analysis and measurements of blast-induced ground vibrations during the construction of Istanbul Kagithane – Piyalepasa – Dolapdere – Dolmabahçe highway tunnels. These tunnels known as T1 and T2 are being constructed by a joint venture group. Within the scope of the study, the particle velocities and frequencies associated with 126 shots during the advancement of the tunnels were monitored and analyzed by vibration monitors at the test site. During the statistical analysis, three different predictor equations widely used in the literature were used to predict peak particle velocity (PPV) and the results and comparison of the predictor equations are presented in this paper. Finally, the particle velocities and frequency values of all blast events were evaluated according to USBM and German DIN 4150 Norms in order to determine the damage risks of the neighboring buildings and structures.

Jan 1, 2008

By Nick D. Rose

Outline ?Background ?History of inverse-velocity for failure prediction ?Methodolog ?Case Histories ?Three case examples of predicted slopefailure to actual date of occurrence ?One case example of mitigated slope failure using inverse-velocity to forecast failure time and schedule remedial measures ?Conclusions

May 1, 2006

By Roberts W. P H, Chant R. A

Investigation of the "whole-rock" major element geochemistry of the Broken Hill lodes and of the rocks immediately enclosing them has been carried out on the full lengths of 19 diamond drill cores transecting B lode,A lode, No. 1 lens and Lead lode in The Zinc Corporation Ltd.-New Broken Hill Consolidated Limited, at the southern end of the line of lode.It appears that the abundances of all of the principal "non-sulphide components" - Si02, AI2O3, Ti02, CaO, MgO, MnO, K2O, TiO2 and P203 - are closely tied to the incidence of sulphide. The well-known direct relationship of calcium and manganese with the incidence of sulphide is confirmed, and to this is now added the pairing sulpnide-phosphate, which is particularly welldeveloped in the zinc lodes. It is also now shown that there is a clear inverse relationship between sulphide on one hand and AI2O3, Ti02 , MgO, and K2O on the other.Total Fe-which is an important constituent of both sulphide and non-sulphide-appears to occur in essentially similar amounts in ore and enclosing materials. The incidence of Na20, while generally depressed in ore, issomewhat erratic and equivocal. Si02 and sulphide usually show a highly systematic inverse relationship-a feature stemming inevitably from their being by far the two most abundant, and hence two co-dominant, materials ofthe ores.These features of elemental abundance are interpreted in the context of seaflooor hydrothermal ore deposition to give some insight into the amount and nature of detrital and of chemical sedimentation, the formation and accumulation of different clay minerals, the chemical and physical characteristics of the bottom waters, and the reasons for the comparative paucity of iron in the Broken Hill lode.

Jan 1, 1978

By Linneas W. Laage

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation.

Jan 1, 1995

By Manqiu Xu, Peter Wells, Gord Bacon

"A methodology is proposed for milling flowsheet design using flotation rate, selectivity and residence time distribution data. The flotation rate data and the difference in flotation rates between the main minerals to be separated are determined from laboratory batch tests. The residence time distribution (RTD) data is calculated using the tanks-in-series model assuming each flotation cell is a perfect reactor. The rate, selectivity and RTD data can be used to calculate the optimum flotation cell number in a bank for rougher/scavenger in a commercial plant.This methodology is demonstrated in a case study of a nickel sulfide ore. It is shown that miniplant rougher/scavenger data can be closely predicted from a batch test using the proposed methodology.INTRODUCTIONIt has been the trend in the past several decades that large flotation cells are increasingly used. This is largely driven by the economics as ore grades are getting lower and the rate of ore processing must be increased in order to keep mining operations economically viable. The development and evaluation of 250 to 500 m3 WEMCO SmartCell and Outokumpu TankCell flotation machines are well in progress. There are many advantages in using large cells: fewer cells, less floor space, lower power cost (although this is now being questioned for fine particle flotation), simpler circuit, simpler control, and lower auxiliary equipment cost (Arbiter, 1999). As flotation cells are getting larger, the importance of cell hydrodynamics, namely, air/slurry dispersion, power intensity, froth transfer, residence time distribution (RTD) and short-circuiting are being fully recognized (Jonaitis, 1999; Weber, et al., 1999; Gomez and Finch, 2002). It is not the intention of this paper to discuss flotation cell scale-up. The intention is to answer what is the optimum number and size of cells in a flotation bank for a given throughput. Figure 1 illustrates this problem facing design engineers. The same mean residence time required for a given throughput can be achieved in a single large cell, or many smaller cells in a row. A few cells of large size may be more cost-effective but they may not be as effective as more cells of smaller size in achieving the optimum metallurgy."

Jan 1, 2005

By Lee W. Abramson, Kenneth P. Akins

The authors have accumulated published data on residual soil and rock tunnels in the United States and have compared it to transit tunneling experience in Atlanta, Georgia, and tunnels in other soil and rock conditions. Two 6.1 meter (20 foot) diameter shield driven, compressed air tunnels were constructed for the Metropolitan Atlanta Rapid Transit Authority (MARTA) connecting the Five Points Station (central hub) with the Peachtree Center Station (first station on the north line). Because of the historic multi-story structures above the tunnels and the variety of subsurface conditions, a comprehensive ground monitoring and observation program was conducted. Conclusions are drawn regarding residual soil and rock ground response due to tunneling. Comparisons are made to ground response due to tunneling in other soil and rock conditions.

Jan 1, 1983

By Jom Kresta

Fundamental changes in the Bitumen Production process at Syncrude have led to the integration of Mining and Extraction operations. Successful operation of the integrated process requires the coordinated effort of several business units. Hence, decision-making has become increasingly more complex and better tools are required. IO2 is a collaborative effort to develop a proof-of-concept prototype of a distributed decision-support system for integrated short-term production and maintenance planning with fleet allocation and dispatching. The prototype includes three main modules (planning, dispatch, and maintenance), a shared database, and a simulation module. At this stage, this prototype is used to plan and operate a simulated mining operation. It is used to demonstrate the viability of the chosen systems architecture and algorithms, as well as the information flows and interactions necessary for improving the overall performance of the integrated operation. While the problem is demonstrated using Syncrude?s site, the methodology is applicable to most integrated resource allocation problems.

May 1, 2002

By Yavuz Ali Topkaya

Rare earth ferrosilicide is a versatile alloy mainly used to control the detrimental effects of sulfur in steel and to modify graphite structures in cast iron. The aim of this study was to determine the optimum conditions to make rare earth ferrosilicon alloy using a preconcentrate produced from a bastnasite type of ore present in the Beylikahir-Eskisehir region of Turkey. This concentrate contained 23.5%REO, 41.37% CaF2, 10.69% BaSO4, 8.50% CaCO3, 4.18%Fe2O3, 2.83% Al2O3, 2.74% SiO2, 1.20% P2O5 and small amount of other oxides. The initial metallothermic reduction of this concentrate using ferrosilicon and aluminum in a graphite crucible placed in a muffle furnace gave very low recoveries due to the difficulties encountered in adjusting the slag composition, temperature and amount of additives. Therefore, two batches of rare earth oxide concentrate containing 61.1% and 81.7% cerium oxide, respectively, that were procured from a Turkish glass producer, were used to optimize with respect to temperature, duration, slag-making additives and amount of reducers. In these experiments, smelting and reduction was done in an induction furnace with graphite crucible, and, ferrosilicon and aluminum were added after melting the charge. As a result, there was no difficulty in obtaining a rare earth ferrosilicon alloy containing 35-55% RE, 5-25% Fe and 20-40% Si, with about 80% metal recovery. When the optimum conditions were applied to the preconcentrate, alloys of similar compositions were obtained with 70-80% recovery. Experiments were also done with mixtures of preconcentrate and rich concentrate, and, recoveries as high as 95% were obtained. Only in this case, to increase the recovery, mixtures had to be charged to the empty graphite crucible after heating the crucible to the required temperature.

Jan 1, 2006

By Wm. Ross Wayment, Innes P. Grantmyre

INTRODUCTION It has been recognized for some time that major changes in mining methods will be required in the near future. Two types of factors contribute to this need for change. Intrinsic factors include ground control problems associated with mining at increasing depths, noise, dust, toxic fumes, and logistics problems which arise from operation in a cyclical fashion. Extrinsic factors include competition for labor from industries offering safer and less difficult work, pressure for less impact on the environment, and changing economic and political conditions. The search for new mining methods has resulted in extensive research being carried out on such novel approaches as thermal fragmentation, high-pressure water jets, sonic drilling, microwave fragmentation, and laser cutting, among others. Joy Manufacturing Co. has elected to concentrate on impact breaking in stopes as a first generation continuous hard rock miner. IMPACT BREAKING Fragmentation techniques show a drop in specific energy as efficiency improves. Specific energy is the energy consumed per unit volume of rock removed and is affected by such variables as rock material properties, fragmentation method used, operator skill, tool design, etc. Mechanical fragmentation methods generally have specific energies much lower than that of the more novel methods. Table 1 shows impact breaking to have an efficiency exceeded only by that of drill and blast methods and it is this high efficiency which led Joy to impactors as the subject for research on potential mechanisms for continuous mining in hard rock.

Jan 1, 1976

By Ryan W. Ulansky

This paper presents the conceptual design of a magnetically-levitated skip for use in an underground mine. A skip is used to move rock from an underground mine to its surface processing facility. Conventionally the skip is raised and lowered by cables, similar to an elevator. In a magnetically-levitated skip, the cable is replaced with a linear induction or synchronous motor to provide propulsion and levitation. Removal of the cables in a magnetically-levitated skip provides many advantages over a conventional system including the ability: to negotiate corners, to travel vertically in the shaft as well as horizontally to the mining face, and to move a very large volume of material using multiple skips in a small shaft. A magnetically-levitated skip is a safer, more environmentally-friendly, productive alternative to conventional skipping. It has the further advantage to decrease haulage distances for underground vehicles.

May 1, 2002

By Keith A. Heasley, John L. Ellenberger, Paul W. Jeran

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 m (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.’s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysis of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

By Jack Elorenta

We often hear that, "Blasting was an art, but now blasting is now a science". 'Scientific' blasting implies that we have quantified and reproducible measurements of the feedstock and product of the blasting process. However, the industry's reluctance to adopt two key technologies, drill monitoring and optical size analyzers, sheds doubt on the claims of scientific blasting.

Jan 1, 2003

By A. J. Partos

One Liberty Place, at 315 m is the tallest building in Philadelphia, PA USA. It is supported on drilled piers socketed in heterogeneous rock. 3832 kN/m2 end bearing and 383 to 766 kN/m2 shaft resistances were selected. Design load distribution was 40% on the base and 60% by shaft resistance. The maximum compression on the corner core columns is supported by clusters of 3 drilled piers. In order to confirm load distributions along shaft and at the base, Drilled Pier G-10 supporting T13-A type outrigger column was instrumented. This column supports 53,849 kN compressive load which includes 13,440 kN windload. This paper reveals details about the process to select the final design for One Liberty Place together with pertinent Information about site geology, foundation construction, quality control, and methods of steel erection. It also presents detailed Information on the type of Instruments, their calibrations, field fabrication, and installation in the shaft of Pier G-10. Readings of concrete temperatures, computed loads, and load distributions are presented for a period from October 1985 through May 1988. The building was completed in 1987.

Jan 1, 1989

By S C. Labram, A Stabile

"Modern train load out stations are becoming faster and have the ability to load a 100 wagon train in less than three hours. At 70 metric tonnes per wagon, that is an average fill rate of 2333 t/h and considering the train is continuously moving, the instantaneous feed rate into the wagon is in the region of 4200 t/h.The main feed conveyor that maintains the level in the surge hopper, above the final weigh hopper, operates in excess of 5000 t/h to ensure uninterrupted charging of the weigh hopper to not disrupt the train loading operation.To avoid demurrage costs (a charge by the Rail Operating Company for exceeding the contractually agreed loading time) the train has to be handled speedily and efficiently and spend the absolute minimum time at the loading facility. Everything else has a much lower priority, including sampling.Thermo Fisher Scientific’s brief was an engineering, procurement and construction management (EPCM) contract to provide a sampling scheme adjacent to the prepurchased and predesigned load-out facility, but which interfaced seamlessly with the loading system of the trains and provided the following: an instantaneous particle size distribution (PSD) result for each truck loaded, and a final PSD for the total train prior to the train leaving the loading facility a crushed (-3 mm) composite sample for chemical analysis for the whole train a composite physical analysis sample for the whole train.The design presented some interesting challenges to our team, but the end result is a system that not only ‘stands alone’ but interfaces seamlessly with the loading system. This paper discusses the design itself and potential improvements to future systems.CITATION:Labram, S C and Stabile, A, 2017. An automatic sampling methodology to determine contractual particle size distribution in rapid train load out stations, in Proceedings Eighth World Conference on Sampling and Blending, pp 229–234 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

The history of mining is rightly proud of its achievements in improving productivity and cost improvements over the years. No matter what measure is used, tonnes per manhour, cost per tonne, etc vast improvements have been made over the last hundred years. In fact over the last ten years in Australian coal mines raw coal output per employee has increased by 60 per cent. When one examines why these improvements have taken place the principal reasons have been technological advancement in mining equipment, excavator and dump truck capacity increases, longwall and continuous miners continually improving in reliability and size. Of course all these improvements are correlated to an increase in capital cost. Even with the above-mentioned advances the pressure for increased performance is as strong as ever. The international mining and mineral-processing sector is currently operating in a recessive market with some traditional commodities, eg gold trading at 20 year lows. During recessive times senior management will demand greater returns on capital employed: the obvious choices being reducing costs or increasing throughput. In addition, head office environments will often place a capital freeze on operational management so the opportunity to take advantage of technological change is not available. The challenge is, therefore, to increase throughput and cut costs without the need for capital. The answer is to optimise the existing labour and plant. If done systematically a result in productivity improvement, in our experience, as high as 45 per cent can be achieved with the average across South East Asia and Australasia being 21 - 23 per cent. The intention of this paper is to present a systematic approach to labour and machine utilisation thereby gaining the greatest possible return on the existing capital base.

Jan 1, 1999

By George H. Hope, Steve Ciccone

"The Red Dog Mine is both the largest known zinc reserve and the largest zinc producer in the world. The mine started in 1989, and by 1999 had increased production from approximately 300,000 tonnes per year (t/yr) of zinc concentrate to in excess of 900,000 t/yr. The VIP Mill Optimization Project further increased zinc concentrate production to 1.1M t/yr while improving both product quality and zinc recovery. The Mill Optimization project also addressed a number of issues related to risk reduction: power generation capacity, water treatment capacity and concentrate thickening. The project was faced with numerous challenges, the most daunting of which was the schedule. This US$105M project was executed, from conception to completion, inside of two years. Less than nine months elapsed from concept to delivery of materials and equipment to site. The project also faced a 100-day ice-free shipping window, the challenges of construction in an Arctic environment, and an extremely tight labour market for qualified craft personnel. These challenges were successfully addressed with several innovative approaches to project execution, including an Alliance contracting arrangement between the owner, engineer and contractor; full integration of the team; construction of modules in Anchorage; and fast-track engineering, procurement and construction.INTRODUCTIONThe Red Dog Mine, which began operations in 1989, is located above the Arctic Circle in Northwest Alaska, approximately 145 km north of Kotzebue (Figure 1). An 80-km road connects the mine site to the DeLong Mountain Transportation System (DMTS) port site. Red Dog is the largest known zinc deposit in the world, with known reserves totalling 94.5M tonnes, and is the largest zinc producer with a concentrate production rate of more than 1.1M t/yr.Open-pit mining is by typical drill, blast and load operation using moderately sized mining equipment. Ore is processed through conventional crushing, grinding, and flotation to produce separate lead and zinc concentrates. Filtered zinc and lead concentrates are trucked year-round to the DMTS port site, where they are stored in two A-frame buildings, 330 and 440 m long. A lightering barge system is used to transfer concentrate from the shallow water load-out to deep-sea vessels anchored approximately two miles offshore. Shipping is limited to a 100-day, ice-free window beginning in early July."

Jan 1, 2003

By G. Chi, A. Solomon, J. Lai

"The Buffalo gold deposit is a small deposit consisting of auriferous quartz-tourmaline veins within a granodiorite stock in the Red Lake greenstone belt. This study aims to characterize the mineralizing fluids through fluid inclusion and stable isotope analyses and to compare them with those of the world-class Campbell- Red Lake deposit. Four types of fluid inclusions were recognized, including carbonic, aqueous-carbonic, aqueous, and halite-bearing aqueous, with the carbonic type being the most abundant. Raman analyses indicate that the carbonic phase mainly consists of CO2, with minor amounts of N2 and CH4, and rarely detectable H2S. The homogenization temperatures of the carbonic inclusions range from -41.7° to 30.9°C. The homogenization temperatures and salinities of the aqueous, halite-bearing aqueous, and aqueous-carbonic inclusions are 130° to 276°C and 9.7 to 23.6 wt.% NaCl equiv., 155° to 207°C and 32.9 to 42.3 wt.% NaCl equiv., and 215° to 357°C and 8.3 to 19.7 wt.% NaCl equiv., respectively. The d18OVSMOW values of tourmaline range from 8.2‰ to 9.0‰, and those of quartz from 11.4‰ to 11.9‰, with estimated fluid temperatures from 323° to 399°C based on the quartz-tourmaline isotopic geothermometer. It is postulated that separate CO2-dominated and aqueous fluids intermittently invaded the fracture/vein system in response to fluid pressure fluctuations, with limited mixing. The CO2-dominated fluid, previously recognized in Campbell-Red Lake as the main mineralizing fluid, is inferred to have been derived from deeper parts of the crust. This deep CO2-dominated fluid reservoir might have been a common source for gold mineralization in the Red Lake greenstone belt. Le gîte aurifère Buffalo est un petit dépôt composée de veines de quartz-tourmaline à l’intérieur d’un stock de granodiorite dans la ceinture de roches vertes de Red Lake. Cette étude vise à caractériser les fluides impliqués dans la minéralisation par les inclusions fluides et par les isotopes stables ainsi que de les comparer avec ceux du gîte de classe mondiale de Campbell-Red Lake. Quatre types d’inclusions ont été notes, incluant des inclusions carboniques, aqueuses-carboniques, aqueuses et aqueuses avec halite, les inclusions carboniques étant la variété la plus abondante. Les analyses par spectroscopie Raman indiquent que la phase carbonique consiste principalement en CO2, avec des quantités mineures de N2 et de CH4, et rarement avec des quantités mesurables de H2S. Les températures d’homogénéisation des inclusions carboniques vont de -41.7° to 30.9°C. Les températures d’homogénéisation et les salinités des inclusions aqueuses, aqueuses avec halite et aqueuses-carboniques sont varient de 130° à 276°C et de 9.7 à 23.6 poids.% NaCl équiv., 155° à 207°C et 32.9 à 42.3 poids.% NaCl équiv., et de 215° à 357°C et 8.3 à 19.7 poids.% NaCl équiv., respectivement. Les valeurs de d18OVSMOW pour la tourmaline vont de 8.2 à 9.0‰, et celles du quartz de 11.4 à 11.9‰, avec une température estimée du fluide entre 323° et 399°C sur la base du géothermomètre isotopique quartz-tourmaline. Il est postulé qu’un fluide riche en CO2 et un fluide aqueux distinct ont envahi le système de fractures/veines par intermittence en réponse à des variations dans la pression des fluides, et qu’il y a eu peu de mélange. Le fluide riche en CO2 est également observé à Campbell-Red Lake ou il est le fluide minéralisant principal, il est présumé être dérivé de portions plus profondes de la croûte. Ce réservoir profond de fluides riches en CO2 pourrait être la source commune des minéralisations aurifères de la ceinture de roches vertes de Red Lake."

Jan 1, 2009

By Miyuki Morioka, Michael J. Griffin

Discomfort, annoyance, or interference with activities due to exposure to vibration is only expected if the vibration exceeds the threshold for the perception of vibration. When there is more than one vibration input to the body (e.g. at the hands, seat and feet), the sensation is first experienced at the location with greatest sensitivity. Knowledge of differences in the thresholds of perception for vibration at the hand, seat, and feet should assist the identification of sources of discomfort caused by vibration. Perception thresholds for vibration have been determined in several studies, but only a few studies have investigated perception thresholds in the horizontal direction for hand-transmitted vibration 1, 6 or whole-body vibration 4-5, and there has been little consideration of perception thresholds for the foot resting on a vibrating surface. This study determines absolute thresholds for the perception of sinusoidal lateral vibration, examining the effect of vibration frequency (8 to 315 Hz for the hand and foot; 2 to 315 Hz for the seat) and the effect of input location (the hand, the seat and the foot). Methods Three groups of twelve males aged between 20 and 29 years participated in the experiment. Subjects in each group attended an experiment to determine perception thresholds for lateral vibration via either a rigid handlebar (30 mm diameter) at the left hand (left hand), or a rigid contoured seat (250 mm x 150 mm), or a footrest at the left foot (30.5 mm x 10.5 mm with 10-degree inclination). For the non-exposed hand (right hand) or foot (right foot), a stationary handle and footrest with the same dimensions as the vibrating handle and footrest were provided so that the same body posture was adopted among the three groups of subjects. An up-down (staircase) algorithm was employed to determine thresholds in conjunction with a three-down one-up rule. A single test stimulus (2.0 seconds) was presented with a cue light illuminated during this period. The task of the subjects was to indicate whether they perceived the vibration stimulus or not. The threshold was calculated from the mean of the last two peaks and the last two troughs, omitting the first two reversals. Results The median absolute thresholds of the 12 subjects determined at each frequency for the hand, seat and foot are shown in Figure 1. A frequency dependence of the threshold contours within the investigated frequency range is evident, with similar shape to the threshold contours

Jan 6, 2006