Search Documents

By William E. Frazier

The presence of minute amounts of sulfur (10ppm) in nickel-base superalloys has been associated with reduced oxidation resistance and the premature spallation of protective coatings. Removal of sulfur by annealing these alloys in a hydrogen atmosphere has been successfully attempted by several researchers. This paper examines the fundamental thermodynamics and kinetics governing hydrogen desulfurization of elemental nickel. Limiting conditions for successful desulfurization are delineated. Assuming that the diffusion of sulfur is the rate limiting process of desulfurization, the effectiveness as well as time associated with hydrogen desulfurization is explored.

Jan 1, 1994

By B. Ozturk, K. Ito, R. J. Fruehan

"A simulation model for bath smelting processes for the production of iron was developed which predicts the coal, flux, ore, and oxygen consumptions and the off gas volume, temperature and composition. The model is comprehensive in that it takes into account all of the important variables including coal composition, metal composition, ore composition, slag basicity, post combustion ratio, (PCR), prereduction degree (PRO), heat transfer coefficient (HTC) , flux, scrap charge, and heat losses. Four basic cases were considered: I. 30% PRO-50% PCR; II. 90% PRO-O% PCR; III. 60% PRO-30% PCR; and IV. 0% PRO-50% PCR. Several different coals were considered and a sensitivity analysis of the critical variables was performed. The model also estimates the sulfur content of the metal. The major conclusions included:1. Post combustion significantly reduces coal consumption but above 20% PCR little reduction of FeO to Fe can be performed with the off gas.2. Prereducing to FeO (Case I) and having as much post combustion as consistent with good heat transfer is an attractive process. This process only requires a simple pre reducer, uses less coal, and is relatively insensitive to the type of coal used.3. High off gas temperatures may pose a potential problem. The off gas temperature can be reduced by using an 02-Air mixture for post combustion, limiting post combustion or adding water to the gas.4. The use of CaC03 in place of CaO or of supplemental electricity does not appear attractive.5. The melting unit is theoretically an energy efficient scrap melter. For Case I using 200 kg of scrap as part of the charge the coal consumption decreases by about 80 kg.6. With PCR > 30% the FeO content of the slag is expected to be 2-5%, and the metal will not be saturated with carbon. These factors and the increased sulfur load since coal is the fuel indicate the sulfur content of the metal may exceed 0.25%"

Jan 1, 1988

By Leonardo Mota, Felipe Perissé Duarte Lopes, Marcelo Gomes da Silva, Sergio Neves Monteiro, Helion Vargas

"Natural fibers, as a class of material, are attracting the interest of engineering sectors owing to specific advantages such as comparatively reduced cost and lower density as well as environmental benefits associated with renewability and biodegradability. For industrial applications, thermal properties, among others, are required. These are major requirements, especially in the case of an insulating natural fiber. In the present work, thermal properties of the curaua were investigated by photothermal techniques, i.e., the open photoacoustic cell and a method based upon the monitoring of the temperature evolution as a function of time. This investigation, in tum, permitted to evaluate two important thermal properties: the thermal diffusivity and the specific heat capacity of the curaua fibers. Indirectly, by means of simple mathematical relations, the thermal conductivity was also obtained. The results were compared with other materials and characterize the curaua fiber as an efficient insulator.IntroductionMaterials are gaining attention in recent years owing to their benefits for the environment as compared to synthetics. Being biodegradable, yearly renewable and recyclable, the natural planted-based are considered fully sustainable [1]. In particular, their life-cycle, from growing to industrial processing, absorbs as much C02 as it is emitted and makes them neutral with respect to greenhouse gases responsible for global warming [2]. Typical examples of these environmentfriendly materials are the lignocellulosic fibers that have been used in simple items such as ropes, baskets, textile, modest roofing, etc, since the beginning of our civilization [3]. In the past few decades, these natural fibers have been extensively investigated [ 4-1 O] as a possible reinforcement phase of polymer composites in substitution for synthetic fibers. In fact, engineering application of lignocellulosic composites are today in the market, especially in the automobile industry [11-13]. Out of the hundreds available natural fibers, only part of them exhibits superior properties to be qualified for composite reinforcement."

Jan 1, 2011

By Norman Schapiro

Future ore bodies will, most likely, be more costly to find, mine and process than those now in production because most of them will be of lower grade or found deeper. To evaluate an ore deposit for extraction of metal values it is important to select the optimum economic process from among the many available options. The physical and chemical behavior of the minerals present should govern the process selection. Process mineralogy which combines mineralogy and petrography with process development engineering generates the data on mineralogy, composition and texture of gangue and valuable minerals from which the optimum process steps can be selected in the commercial design of the ore processing plant. These insights also help in solving operating problems caused by changes in the ore body

Jan 1, 1981

By Baozhong Ma, Qian Li, Yonggang Wei, Shiwei Zhou, Bo Li, Chengyan Wang, Hua Wang

The magnesium-rich nickel oxide ore (w (Ni) =1.09 %, w (MgO)=29.08 %) mixed with 6 % and 8 % anthracite were roasted at different temperatures. XRD and SEM/EDS techniques were utilized to characterize the phase and microstructure transformation of the ores. The results show that lizardite and chrysotile of raw ore were converted into forsterite and enstatite during reduction roasting process. Simultaneously, iron and nickel oxide were reduced and migrated from the initial magnesium silicate. Fe3Si were formed when the roasting temperature went up to 1300 ℃ and 1350 ℃, and a small amount of Ni was observed in it. Temperatures got too high were not benefit to the polymerization of ferronickel.

Jan 1, 2015

By J. Vander Linden, R. De Ketelaere, M. Verhaege

In this paper, results are presented concerning the search to implement Supported Liquid Membrane (SLM) technology for the recovery of copper from electroplating effluents. Acid copper electroplating rinse solutions or effluents resulting from the post-treatment of, for example, cyanide-containing copper electroplating baths all contain copper (2+) in the lower concentration levels. A thorough study of the influence of the individual parameters and of their combined impact on mass transfer in small scale laboratory SLM modules has been performed, enabling to set forward the appropriate operating conditions for a pilot plant installation. The pilot plant, containing two SLM modules. of 18 m2 of surface area, has been tested extensively, including short and long term runs, with real process solutions. It was demonstrated that this installation is able to treat 40 l/h of acid copper sulphate rinse solutions· containing 500 ppm of copper. The final copper concentration in the effluent can be reduced to a few ppm while copper metal is recovered by electrolysis of the concentrate. This technology is also applicable to the treatment of solutions with low copper content of origins other than plating shops, such as tailings from copper plants or mine waters.

Jan 1, 2000

By C. M. Davidson

Contamination of by-product: sulfuric acid, by dissolved oxides of nitrogen ('nitrates') occurs under some operating conditions encountered in sulfide roasting and smelting,, notably when oxygen-enriched air is used. This 'nitrate' lowers the value of the acid and increases the effective cost of smelter gas desulfurization. The present paper describes measures taken at one smelter acid plant to remove this 'nitrate'; it discusses the mechanism by which 'nitrates' in some cases concentrate in one part of the plant and can be purged for more efficient treatment; and it describes a process developed by C-I-L Inc. for removal of 'nitrates' from such a purge stream. Advantages of the process include very low reagent cost, recovery of all sulfuric acid values and safe handling of nitrous fumes.

Jan 1, 1983

By Frederico Muylaert Margem, Giulio Rodrigues Altoé, Glenio Daniel, Pedro Amoy Netto, Sergio Neves Monteiro, Maria Carolina Andrade Teles

The environmental concern is creating pressure for the substitution of high energy consumption materials for natural and sustainable ones. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as flexibility and toughness. So there is a growing worldwide interest in the use of these fibers. Fique fiber extracted from fique plant, presents some significant characteristic, but until now only few studies on fique fiber were performed. This work aims to make the analysis of the tensile strength of polyester composites reinforced with fique fibers. The fibers were incorporated into the polyester matrix with volume fraction from 0 to 30%. After fracture the specimens were analyzed by a SEM (scanning electron microscope).

Jan 1, 2015

By A. S. Usmani

The flow associated with the pouring of molten metal into moulds has been modelled on the basis of certain simplifying assumptions. A finite element based Navier-Stokes equation solver has been used to analyse the flow. The velocities obtained from the Navier-Stokes equation solver are used to advect a pseudo-concentration function for modelling the fluid front. A simple problem with a known analytical solution is solved first to test the model. Subsequently, several more examples with varied geometrical configurations are modelled, including one with curved flow boundaries.

Jan 1, 1992

By B. K. Chakrabarti

Modeling and a screening design of experiment (DOE) was performed with the process variables to identify the greatest effect of variables on the response quality in the dead burning of magnesite refractory in a rotary kiln. Among various interdependent variable factors, the design variables chosen were raw magnesite (RM) feed rate, kiln rotation time i,e, seconds per rotation(SPM) and burning zone temperature (BZT). The response variables chosen were exit gas temperature and density of dead burnt magnesite(DBM). ANOVA and normal plots were used to evaluate the effects.This work had enabled to correlate the BZT, RPM, RM feed with the exit gas temp and density of magnesite produced. The result opens up an avenue to look into the optimum region of operations within the ranges of variables considered in order to conserve energy and to minimize the exhaust gas temperature and to maximize the density of the DBM produced

Jan 1, 2015

By Priscilla Aki Mori de Hanashiro, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Hugo Hashimoto

"The LCDs are used in televisions, calculators, mobile phones, computers (laptops and tablets), video games and other electronic devices. The advancements in technology make obsolete these devices, causing excessive disposal of LCDs and therefore decreasing life span of landfills. In this context, the LCDs from LED LCD TVs arise as an additional source of waste electrical and electronic equipment (WEEE). Thus, it is essential to develop LCDs recycling methods, beginning with the LCD characterization followed by displays processing, aiming the materials separation and using some Ore Treatment Techniques, and finally, the recovery of indium using acid leaching. The analysis methods that will be used in this work are: Fourier Transform Infrared (FT-IR) and Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES).IntroductionLiquid Crystal Display (LCD) technology is applied in modem televisions, calculators, mobile phones, computers and a wide range of electronic devices. It has replaced Cathode Ray Tube (CRT) technology as the most advantageous display product, due to lower electrical power consumption, size and weight reduction, and no radiation emission [ 1]. The constant improving of LCD screen technology reflects on its growing contribution to the amount of waste electrical and electronic equipment (WEEE): an estimated 50 million tons of WEEE are produced every year [2]. Once the most common method of its disposal are landfills, the LCD technology therefore became an environment issue [3].LCD structure is composed by components made by different materials. In order to develop a LCD recycling methodology that gives the right destination to these materials, a previous characterization stage is required. This characterization includes a disassembly process and material identification analysis. One of the LCD components is the screen, which is composed by polymeric and glass layers. The liquid crystal glass was the starting material of this study. It contains indium in the form of indium tin oxide (ITO) film. This ITO film is deposited in the glass by a sputtering process and acts as the electrode material [4,5]. It has in its composition 90% ofln203 and 10% ofSn02 [6]."

Jan 1, 2014

By W. Gutmannsbauer

Thin films of TiO2 nanoparticles have been prepared by different reactive deposition methods, such as electron evaporation, ion plating and ion beam sputtering. Many properties especially the optical properties, are strongly related to the film morphology and surface roughness. Scanning force microscopy was employed to obtain information on the surface structure of as-deposited Ti(h thin films. The influence of the deposition conditions and the film thickness on the optical and structural properties has been investigated. The as-deposited films were found to be amorphous or polycrystalline with anatase structure.

Jan 1, 1995

By Vinicius Alves Gomes, Jean Igor Margem, Thallis Cordeiro, Frederico Muylaert Margem, Roberto Faria Jr., Sergio Neves Monteiro, Marina Rangel Margem

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and neutral with respect to CO2 emission. In particular, the fiber extracted from the malva plant stem is nowadays recognized as one of the strongest lignocellulosic fibers. However, the thermal properties of the malva fibers have yet not been fully investigated. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity of a pressed malva fibers sample. The results revealed that these fibers showed a superior thermal insulation capacity.

Jan 1, 2015

By Huimin Lu, Liyuan Zhao, Zhijiang Gao

The aluminum matrix composite reinforced by graphene was successfully fabricated using high pressure torsion (HPT). With only 0.5wt% graphene, the grain size was reduced to 100nm while that of pure Al was about 500nm. The hardness of the composite increased from the center (64HV) to the edge (120HV) of the sample. Moreover, the tensile strength of this composite reached 197MPa, while that of pure Al was 157MPa. The enhancement in mechanical properties was induced by grain refinement, load transfer from the matrix to the reinforcement and dislocations piled up at the grain boundaries.

Jan 1, 2015

By Brian Patrick, Norman Bell, Mark Schoenfield, Thomas Weber, Dietrich Gross

"The reduction of carbon dioxide emissions and the resultant greenhouse gas affect is hampered by the fact that all fossil fuels contain copious quantities of carbon. Process tweaking can keep the amount of carbon dioxide to a minimum but cannot significantly reduce the amount of carbon dioxide generated. The very nature of utilizing fuels requires that they be burned to release the heat required for the various processes. Reduction of metal oxides to manufacture or modify pure metals, generation of power, transportation and many other forms of fuel usage result in much of the generation of man made carbon dioxide. Oxyfuel is a unique contributor to carbon dioxide emissions. While creating higher concentrations of carbon dioxide the total volume of carbon dioxide generated is reduced. This paper will examine the unique characteristics and potential of oxyfuel that make the generation of lower volumes of carbon dioxide possible.Nearly ten years ago a commercial application of oxy-fuel was installed at Jupiter Aluminum Company in Hammond, Indiana. This process was funded and developed by Dietrich Gross CEO. This aluminum remelt facility now runs completely on oxy-fuel and has continuously for over ten years. This has reduced the melt rates to as low as 750 BTU per pound in continuous melting periods."

Jan 1, 2009

By Dietrich Gross

This paper describes an advanced oxy-fuel combustion technology for re-melting aluminum that significantly reduces energy consumption and emissions. This oxy-fuel combustion technology developed by Jupiter Oxygen is a patented process for combustion of fossil fuels with pure oxygen while excluding air, thereby creating an undiluted high flame temperature and increased efficiency for process heating in industrial furnaces. This unique process has led to improved heat transfer and longer residence time while maintaining the same process temperatures as with air combustion. The energy efficient combustion process allows aluminum companies to operate at a substantially lower cost due to a dramatic fuel savings of up to 70% for natural gas and waste oil (1). The results of more than 10 years of day-to-day experience utilizing the Jupiter Oxygen Corporation oxy-fuel combustion technology licensed to Jupiter Aluminum Corporation in the aluminum re-melting business are discussed.

Jan 1, 2008

By David Hughes

The paper covers the utilization of on-line analysis in process control of solvent extraction in nickel leach solvent extraction processes in Finland and Australia and in copper heap-leach and solvent extraction in Chile. The goals of and requirements for controlling the solvent extraction stages of the processes are reviewed. The applications at three plants are compared. The development of the technology used is reviewed and design considerations are discussed. Requirements for on-line control and analyzer performance are compared. A new generation of analyzers and its effect on the set-up process of a project is introduced.

Jan 1, 2003

By Guangliang Wu, Dong-chang Huang, Xin-bin Liu

High temperature mechanical properties of 50Cr5MoV roll steel was investigated by Gleeble 1500 thermal simulator testing machine The morphology, composition and microstructure of fracture surface were observed and analyzed by OM, SEM and EDS The results are indicative of that, there are two brittle temperature zones of 50Cr5MoV roll steel at the temperature of 600°C~950°C and 1300°C~1450°C, respectively. The section shrinkage rate is less than 60% The fracture mode changes from mixed ones dominated by intergranular to toughness transgranular one with the increase of temperature at the range of 650°C~1300°C. The fracture is along the solid--liquid phase at the range of 1300°C~ melting point It is crucial to formulate the 50Cr5MoV casting technology, to prevent the cracks and improve the quality of 50Cr5MoV roll steel.

Jan 1, 2016

By R. H. Rubisov

Sulphuric acid pressure leaching of nickeliferous laterites has attracted considerable attention from the nickel industry during the past five years. The process is especially advantageous for limonitic laterites that mostly contain goethite, because iron precipitates releasing acid and thus rendering low acid consumption. It is also applicable to mixtures of limonites and saprolites, although at higher acid consumption due to magnesium. Effective process design requires the solubility of metals that precipitate during the process to be known. In the present work, determination of metal solubilities is based on a simple speciation program that assumes the presence of only one dominant complex for each metal. The thermodynamic data for the precipitation reactions are extracted from high-temperature experiments with monometallic systems published previously. The validity of the approach is then tested against mixed bimetallic systems, and finally applied to calculate the solubility of aluminium, iron and magnesium in laterite leaching effluents "at temperature". In both cases of limonitic feed and limoniticfsaprolitic blends, the prediction closely follows metal solubilities measured experimentally at temperatures from 230 to 270°C and at terminal he acidities ranging from 10 to 75 g/L.

Jan 1, 1999

By Bora Derin, Adnan Aydin, Onuralp Yucel, Hakan Morcali

"The steelmaking industry which uses electric arc furnaces (EAF) generates approximately 250.000 tons of EAF flue dusts annually in Turkey. These flue dusts contain valuable metals such as zinc, iron and lead. For example, if these flue dusts can be treated efficiently, disposal problems certainly decreases and annually almost 40.000-75.000 tons of zinc can be recovered. In this study, powder and pellet forms of EAF flue dusts taken from a steel mill were carbothermally treated in a temperature controlled pilot scale rotary furnace via carbothermal reduction in order to investigate the reduction behavior of Zn and Pb. Temperature (900-1000 and 1100 °C) and time (0-90 minutes) were selected as reaction parameters. The chemical analysis was performed for the sample residues.IntroductionTurkey’s steel production reached to 23.3 million tons in 2006. There are three integrated steel plants of which capacities vary from 0.7 to 3 million tons per year and seventeen EAF steel plants of which capacities vary from 0.06 to 2 million tons per year [1]. When it is considered that more than 74 % of the Turkish steel production is produced by EAF method and approximately 10 - 15 kg of dust is formed per ton of steel during this process, the amount of annual generated EAF dust may be estimated at approximately 0.25 million tons. EAF dust which contains valuable metals such as zinc, lead, iron, cadmium, and chromium, is considered as hazardous waste product in steelmaking industry. If these flue dusts can be treated efficiently, not only the disposal problems certainly decrease, but also annually almost 40.000-75.000 tons of zinc can be recovered. Many studies which exist on recovering of the valuable metals from EAF dust, propose and practice many hydro-metallurgical and pyro-metallurgical treatments [2- 7]. In this study a laboratory scale work were performed to investigate reduction behavior of zinc and lead in EAF dust by carbothermal process in a rotary furnace."

Jan 1, 2008