Search Documents

By John A. Herbst, Kuang Y. Lee

Coarse particle size measurement is essential for the automatic control of a size reduction process like crushing or SAG milling in order to achieve optimal process performance. However, the on-line size measurement of coarse material is not easily obtained due to the problems of material handling and sample statistics. A technique based on advanced image analysis and quantitative stereology has been successfully developed and tested in a pilot scale setting. The chord length distribution of coarse particles on a moving conveyor was measured with an image analyzer and then transformed to the mesh size distribution with a stereological model and a special numerical method. Some test results as well as the technique's industrial suitability and limitations of this method are also discussed.

Jan 1, 1992

By S. Chander

Neutralization of acidity by addition of alkaline materials is a commonly used method to treat acid mine drainage. However, this procedure requires large amounts of reagents based on acid-base accounting. The potential use of organic additives in preventing or ameliorating acid mine drainage was investigated in this research. The tests were conducted in weathering columns using refuse samples from a coal cleaning plant. Both cationic and anionic compounds were tested. For a comparison, tests were made in the presence of limestone and lime. The results show that some of the reagents substantially retarded the rate of oxidation whereas others even enhanced it. The suppression of the rate of pyrite oxidation was ascribed to surface chelation. Formation of surface compounds prevented the pyrite particles from further oxidation. Such a treatment required only small quantities of reagents since the reaction was confined to the surface.

Jan 1, 1992

By Martin Knights, Geoff Featherstone, John Flanagan, David Lawrence

The proposed paper will address specific transport, engineering, environmental and community related issues concerning the current construction and future operation of Europe’s biggest urban road tunnel project—the US$500m Dublin Port Tunnel. Situated in Ireland’s capital, the three mile long, 40 ft diameter twin tunnel project encounters a range of ground conditions using TBM, Shield, Cut & Cover with diaphragm walling and major slope stabilisation and Multi-jacked pipe techniques. Where possible units of measurement are given in feet and inches.

Jan 1, 2003

By John F. Papp

Chromite is used both as a metallic and nonmetallic mineral. Chromite ore is used as the source of chromium by the metals industry and is used, without chemical alteration, in the refractory and foundry industries. Chromite ore is also the source of chromium for the chemical industry. On average worldwide far more chromite ore is used by the metallurgical industry than by any other industry. Thus, although the primary purpose of this chapter is to describe the nonmetallic uses of chromite, the metallurgical uses must also be discussed in order to provide a complete description of this commodity.

Jan 1, 1994

By Y. Luo, S. S. Peng

This paper presents some results obtained from research on long-term subsidence over and near chain pillar systems - the area available to long-term subsidence in longwall operations. Although the long-term subsidence for most longwall operations is insignificant, it does exist in some cases. In the cases that showed significant long-term subsidence, it was found that the development process could be expressed by an exponential decaying function. The stability factor of the chain pillar system and the potential for long-term subsidence are the two most important factors that control the magnitude and development characteristics of the long-term subsidence process.

Jan 1, 2000

By Chris Mills

El papel de la separacion gravimétrica en la industria minera es brevemente considerado en perspectiva. Las pruebas e intentos de laboratorio y mineralógicas para el diseñio de los procesos gravimetricos son examinados poniendo especial énfasis en la selección de la tecnologia del proceso. Es tratado y comentado el material disponible en equipos para pequeña escala y trabajo de pruebas-piloto, particularmente en relación a la escalacion y a la adquisición de datos precisos y fiables. El transporte del comportamiento de los datos desde la planta piloto a la planta a escala es igualmente explicado. Son resefiados todos los tipos de equipos a escala total existentes para la separacion gravimétrica, poniendo de relieve las unidades de alta capacidad. Es considerada la disposicion de la planta y la seleccion de 1os equipos auxiliares.

Jan 1, 1982

By Stéphane Servant, Jacques Ouellet, Ferri Hassani

This paper presents essentially the logistic and practical aspects involved for in situ testing of mine paste backfill with a self-boring pressuremeter. The investigation discussed in this paper is part of an extensive and ongoing research project to identify and validate an in situ testing technique for cemented mine backfill such as hydraulic or paste backfill as well as Insitu behavior of backfilled stopes. After a literature review on field testing of soils and past experiments on mine backfill in situ testing, the self-boring pressuremeter was selected as the most appropriate instrument for this task. The authors presents in this paper the technical aspect involved in a field trials that was conducted in a Canadian underground mine using paste backfill. The results of this first successful trials show that self-boring pressuremeter test can provide high quality and reliable backfill characteristics results, using analytical techniques developed for soils (Ouellet et al., 1998). The parameters obtained were: estimation of the lateral stress in the ground, the soil stress-strain response and the soil strength. The logistic and equipment required to conduct such testing underground is fully described. Performance achieved in the field and technical difficulties encountered are highlighted. Recommendations for future experiments with such instruments are given. Some potential technical improvements to better adapt this in situ testing technique to mine backfill are proposed.

Jan 1, 2001

By G. Davey

High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. The operating experience of two existing copper operations will be covered to show the effect of the introduction of the Metso Stirred Media Detritor (SMD) a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from the introduction of this new technology. The benefits and process difficulties are covered and explained.

Jan 1, 2003

By R. L. Lewis

A simple method for estimating the steady-state water quality of a pit lake is presented. The steady-state concentration of a conservative chemical constituent in a pit lake is shown to be a simple function of the inflow rate, the evaporation rate and the inflow concentration. An analytical method is presented for estimating the equilibrium ground water-inflow rate for use in water-quality predictions. The time required to reach chemical steady state is estimated using an iterative mass-balance model. Mine operators should find the methodology useful for planning and screening regulatory applications where conservative estimates of pit lake water quality are desirable.

Jan 1, 2000

By Weixiang Meng, Zhao Song, Ming Guo, Zhigao Liu, Shoubao Zhang

"There are many multi-layer coal reserves in China which account for nearly 20 to 25% of the existing proven reserves. When the coals are mined in a descending order using the fully mechanized long wall mining method, they usually have roof collapse with cavity and air leak in roadways and long wall stopes; this is especially relevant when the thickness of the rock between two coals is less than 5.0 m, as the roof stability of lower seam would be greatly reduced. At the Wuhushan Mine, such abnormal strata behavior occurs, including abnormal support stress, irregular period roof pressure, and roof falls in the face. The main reasons for these behaviors include smaller roof thickness, lower rock strength, and mining influence of upper coal; these reasons were determined by analyzing the in situ conditions. A mechanics-based model of the mine geometry was set up to study the sources of stress, the stress evolution of coal, and the discriminant method of roof stability; to obtain the smallest safe thickness of roof between two coal layers, numerical modeling was applied to analyze the relations between the roof thickness and its displacement distribution. Based on the above research, the No.1001 face was divided into easy roof caving zone (ERCZ), roof caving transition zone (RCTZ), and unlikely to roof caving zone (URCZ). In the ERCZ, comprehensive grouting to reinforce the roof was implemented; in the RCTZ, local grouting to reinforce the roof was implemented. Furthermore, a face stability control index and its range were developed in a fully mechanized face combined with mine pressure observation. After implementing this strategy, there have been no unexpected roof caving or other serious strata behaviors.INTRODUCTIONChina is the country with the largest coal production in the world, and the conditions for its coal seams are particularly complicated. For example, in China’s Datong, Wuda, Pingdingshan, and Qinshui mining areas, there are a large number of multi-layer coal seams. The thickness of these coal seams ranges from 1.3 m to more than 10 m, and the spacing between layers is from under 1.0 m to over 30 m. A common problem with these coal seams is that one layer of mining has a large impact on other coal seams, which are customarily referred to as close-distance coal seams. According to statistics, close-distance coal seams account for about 20–25% and 15–18% of China’s coal reserves and production, respectively.From the reference research of Huang (1999, 2002, 2018) and Tu (2010, 2011) we can learn that in the mining process of close-distance coal seams, downward mining is mainly used. When the upper-layer coal is mined, it has a huge mining disturbance effect on the floor (that is, the roof of the lower coal). The mining disturbance increases the mining fissure in the rockmass and weakens the strata strength. The mining problem formed by this issue is that when the lower coal is mined, problems such as difficulty in roadway support, collapse of stope roof, and difficulty in ventilation are often encountered. Especially for the mining of medium-thick coal seam groups with a layer spacing of less than 5.0 m, there has been a large-scale roof collapse accident with a fall height of more than 10.0 m. In response to such problems, domestic and foreign scholars and engineers such as Tan, Zhao, and Xiao (2010), Xie et al. (2017), and others have also carried out targeted theoretical and practical research."

Jan 1, 2019

By Edward D. Elkins

CalMat Co. is one of the largest producers of construction aggregates in the United States. The CalMat Reliance plant is located in Irwindale, California, and is situated on an alluvial fan formed by the San Gabriel River. The fan deposits are of Quaternary age and were derived from granitic and metamorphic bedrock exposed in the San Gabriel Mountains to the north. The sediments are poorly sorted and range in size from large boulders to clay size particles. The coarse material is hard and durable and consists of quartz diorite, granodiorite, granitic gneiss, schist and minor amounts of volcanic rock. The matrix is comprised of silty sand with varying amounts of clay. Thin silt and clay lenses occur sporadically throughout the deposit. The clay content of the matrix and the degree of weathering of the coarse material increases with depth. Based on seismic data, the alluvial fan varies from 200 to 400 feet thick and overlies crystalline bedrock. The Reliance plant was constructed in 1971 and 1972. It has a nominal capacity of 1200 to 1400 tons per hour, and typically produces more than three million tons of aggregate products per year. Alluvial fan sediments are mined from a gravel pit situated adjacent to the plant. The material is fed through a mobile, 48- by 60-inch, in-pit jaw crusher, then transported by conveyor to the main plant to be processed. The plant is modern and highly efficient. It has a typical wet and dry circuit and is capable of producing a wide range of aggregate products. To extend the life of the plant, a 9,000 foot conveyor system is being constructed to connect it to a granite quarry operated by Azusa Rock Inc. The quarry is located north of Irwindale, and is 50 percent owned by CalMat Co. The conveyor will be used to export crushed rock from the quarry to Reliance. The existing plant will be modified to process the crushed rock.

Jan 1, 1995

By Thomas Schultheis, William Heron, Paul Watson, Colin Warren

This paper describes the geology and geotechnics associated with construction of the Thames Tunnel, part of the UK’s Channel Tunnel Rail Link (CTRL). The 2.5km long twin tunnels run beneath the river Thames at depths of up to 40m and are currently under construction. They pass through varying geology comprising alluvium, terrace gravels and chalk with flints and are currently being bored using Herrenknecht mixshield slurry tunnel boring machines (TBM’s). This paper outlines the lithology and engineering properties of each geological formation and describes the geotechnical processes, potential hazards and difficulties experienced in the works. A summary is given into the extent of the investigative work in terms of route selection, tunnel design, TBM optimisation and further details are provided on the geotechnical aspects associated with the construction of the tunnel approach structures and the tunnels.

Jan 1, 2003

By H. Suharyono, R. Hogg, P. Bunnaul

The flocculation of fine-particle suspensions by polymers is a nonequilibrium process whose performance is strongly influenced by physical as well as chemical variables. A standardized test procedure has been developed that provides quantitatively reproducible measurements of process performance in terms of the floc settling rate, supernatant turbidity and sediment compressibility. The procedure provides information on the development of flocs in response to polymer addition and on their degradation behavior during subsequent handling. Extensive experimental observations using a variety of solids and flocculant types have been used to develop criteria for reagent selection and process design. It is shown that the appropriate choice of reagent(s) is determined primarily by chemical factors (solid type, solution chemistry, etc.). However, actual performance depends more on physical variables, such as agitation intensity and the rate of flocculant addition. Some general guidelines for flocculant selection and process design in industrial applications are suggested.

Jan 1, 1994

By Richard W. Brummett

Problems in new strip mine development is a subject that could require several days to cover adequately. Coupled with the fertile imagination of television writers, we could probably expand it into a series rivaling Gunsmoke in longevity with just as many shootouts at sundown. It would-of course-be subject to a high Neilson Rating. To bring the subject into perspective, we will limit the comments to a general discussion covering western strip coal developments. Stimulated by increased demand for low sulfur coal, surface mineable western coal operations began a shift into high gear approximately four years ago. Then came last year's "energy crisis" that increased the pressure on coal development not only in the west, but nationwide. Several eastern power plants having dual oil and coal burning facilities were directed to discontinue using oil. Also, a number of new south and southwestern power plants scheduled to burn natural gas or of I commenced an ordered conversion to other fuels, namely, coal. The involved utilities with reserve positions accelerated their planning while others began the search for long-term commitments from coal producing companies. In addition, announcements were made for proposed mine mouth coal gasification projects in New Mexico, Wyoming, and North Dakota.

Jan 1, 1974

By G. I. Voiloshnikov, V. E. Dementyev

Wide use of adsorption methods for metal recovery is one of the most important achievements of gold metallurgy of the last decades. Anion exchange resins or activated carbons may be used as adsorbents. This paper presents a brief overview of IRGIREDMET effotts on development, testing and implementation of techno­logical flowsheets using both adsorbent types and attempt to compare their technological properties. IRGIREDMET Institute was founded in 1871 as a laboratory for gold smelting and gold ore testing. In 1930 it obtained the status of the Research Institute. IRGIREDMET functioned as leading research center for gold mining industry in the former Soviet Union. At present it is the Open Joint Stock Company dealing with all s01t of research and design works for gold min­ing (ranging from geology to gold refinery). IRGIREDMET started development of ion exchange technol­ogy in 19641• The first stage of work (1964-1970) including development of principle flowsheet of RIP process was carried out jointly with the Moscow VNIIKHT Institute (All-Russian Scientific Research Institute of Chemical Technology)2• The flowsheet of RIP process is presented in Fig. I and includes the following basic operations: gold adsorption from pulp; washing of loaded resin; acid treatment; thiourea adsorp­tion; gold elution by acid thiourea solution; resin washing to remove thiourea; alkaline treatment of resin; resin washing and gold recovery from eluates by electrowinning. The technology developed and equipment used were tested for treatment of clayey ore of Kuranakh deposit at a pilot plant of the Lebedinsky gold complex ("Aldanzoloto" company, Yakutia, Russia). The pilot plant throughput was 200 t/day. At the same time IRGIREDMET conducted the tests on ion exchange technology for ore and concentration products of oper­ating gold plants and for ores of new deposits. Laboratory and pilot plant tests were done and developed initial data and process design criteria for designing of 15 plans of the former Soviet Union. In the course of this work a great number of newly synthe­sized anion exchangers including strong and weak base resins was studied, the peculiarities of anion exchange resins using two different raw material types ( ores and concentrates includ­ing clayey, carbonaceous, silver bearing, arsenic, antimony and base metals bearing products); some theoretical regularities of adsorption process were investigated; the technology of two stage adsorption of gold and silver from silver gold ore, improved flowsheet for gold elution and resin regeneration, design of adsorption equipment including pulsation columns, design of electrowinning cells were developed; conditioning technology for pulp with complex ion composition prior to gold and silver adsorption was developed, etc.3·8• IRGIREDMET specialists took part in commissioning of practically all the plants in the former Soviet Union using RIP and RIL process including Lebedinsky, Kuranakh, Sovetsky, Karamken, Matrosov's plant and Mnogovershinny plants. Due to this works RIP process became standard technology for Russia and the CIS.

Jan 1, 1998

By Rowan Melrose, Naj. I. Aziz, Arvind Misra

Mathematical models have been developed to simulate longwall heading development systems in Australian Longwall Mines. The models developed consider the effect of non concurrent cutting and supporting systems and concurrent cutting and supporting systems. They also consider the impact of operating parameters on each of these systems. Operating parameters that are considered include pillar dimensions, the use of surge cars, bolting time, shuttle car speed and heading advance per cycle. The effect of these parameters is considered with respect to production rates and also panel advance rates.

Jan 1, 1996

By Stanley J. LeFond

After two disappointing years where most industrial minerals posted decreasing production, 1981 saw an increase in production over 1980, or at least in status quo. Several commodities did, however, post significant gains. For example, bromine posted a 14% increase; fluorspar production dropped 21% in 1980, but gained 24% in 1981; and sulfur production increased. However, perlite was off 13% and manufactured sodium sulfate off 18% in 1981, while natural sodium sulfate production remained almost even with 1980. In fact, many industrial minerals production either remained constant, increased, or decreased only slightly over 1980. Increasing energy costs had their impact on industrial minerals in 1981. Hopefully, the recent downward trend in energy costs, at least gasoline, will financially help some of the more marginal plants. The 1979 shortage of rail cars that did not carry through 1980 also did not carry through in 1981. Rail rates increased 12.8% over-all last year, while average freight rates for industrial minerals increased 15.5%, according to Neil Johnson, consultant. Also, the trucking industry posted a 5-6% decrease in rates due to deregulation. All in all, we in the industrial minerals section seem to be holding our own at least. Stanley J. Lefond Contributing Editor

Jan 5, 1982

By Randal J. Barnes

There are many methods available for the estimation of geologic parameters (Popoff, 1966; Barnes, 1980). In the last decade a new and relatively sophisticated technique using statistical theory has emerged: geostatistical kriging (David, 1977; Journal and Huijbregts, 1978; Rendu, 1978). An interesting property of geostatistical estimation is that when a geologic parameter is estimated for a given volume, not only is the estimate generated but an associated measure of certainty is produced as well. This statistical measure of estimation confidence is called the estimation variance. While the concept of an estimation variance is universally considered to be a good idea, mining engineers and geologists do not currently have the tools to incorporate it into their planning and quantitative analysis. This paper attempts to develop and present some of the necessary tools required to incorporate estimation uncertainty into mine planning. Geologic uncertainty is portrayed as an economic business risk. This risk is objectively characterized, and-the associated cost is quantified. Geologic delineation sampling is viewed in this light as an economic commodity with an associated cost and value. A coal mine planning example is used as a focus in this presentation. The data used is real, though it has been modified to maintain data security and project anonymity.

Jan 1, 1986

By Jeffrey M. Christian

Gold prices are rising, in what is coming to be seen as the beginning of a longer term upward trend. After languishing between $325/oz and $364/ oz from early 1991 into early 1993, prices began rising in the first half of 1993. Gold rose from a low of $326/oz in March 1993 to $414/oz on an intraday basis in early August. There was a speculative sell-off at that point, which took gold prices quickly back down to $350/oz briefly in October 1993. At that time, there still was a fair degree of skepticism about gold's price prospects. Many banks believed that gold prices could not mount a sustained rally. As prices dropped in August and September of last year, these suspicions seemed to be confirmed. Gold prices quickly rebounded, however, reaching $395/oz by early January 1994. The strength of this renewed increase led many banks, investors and others that had held negative views of gold to grow more positive. They began buying gold and trading it from the long side of the market. The result was that gold prices remained strong during the first quarter of 1994, trading between $375/oz and $390/oz.

Jan 1, 1994

By J. Pinkley

In June of 2002 Hilti North America received the first MSHA permissible approval for usage of a powder actuated tool device in a gassy mine atmosphere. The purpose of this paper is to discuss the implementation of this commonly utilized tool technology in the construction industry, to the underground gassy mining industry over the course of the last 5 years. Prior to June of 2002, underground gassy mining industry had attached materials such as ventilation curtains, power cables, communication cables, signage, and other materials by either manually driving individual spads or nails into the mine roof or rib or by attachment to existing roof bolt bearing plates. The Hilti DX 460 powder actuated tool is portable, durable, and lightweight (4.5 pounds). The Hilti DX 460 powder actuated tool system is powered by Hilti .27 caliber permissible explosive boosters. The energy force of the Hilti .27 booster?s acts on a captive piston principle in the Hilti DX 460 powder actuated tool, that applies the setting force for the direct fastening to the individual fastener chosen for the application by the end user. Each year Hilti can be called upon by MSHA to provide booster materials for re-testing per our Hilti DX PAD 1/00 approval.

Jan 1, 2008