Search Documents

By Immo H. Redeker

This is a final progress report on a cooperative project conducted by three private feldspar companies,** North Carolina State University, and the federal Bureau of Mines. The object of the project was to reduce the feldspar tailings disposal problems at the flotation plants in the Spruce Pine area of North Carolina. The initial phase of the project revealed that high tonnages of saleable feldspar and quartz were lost in the tailings and the three feldspar companies are now concentrating their efforts on feldspar recovery, either by reclamation from the tailings as suggested by the Asheville Minerals Research Laboratory or by improvements in metallurgy in the existing plants.

Jan 1, 1970

By Guangyao Si, Ismet Canbulat, Xun Luo, Yi Duan

Routine analyses of seismicity and event locations are essential for coal burst risk management, especially in the presence of unfavorable and complex geology. In an Australian longwall coal mine, a small-scale seismic monitoring network was installed to monitor a section of a major dyke intersected by the roadway, which was classified as a coal burst prone zone. The Deep Convolutional Neural Network (DCNN) technique was adopted for automatically discriminating seismic events to assess seismicity in this zone. The discriminated seismic events were located with the Shortest Path Method based on the Boundary Discretization Scheme (BDS-SPM) for temporal-spatial seismic event distribution analysis. The results demonstrate that the seismic events are discriminated with an average accuracy of 94%. Moreover, the seismic events are more accurately located using the BDS-SPM with a 3D heterogeneous velocity model compared with results obtained with a homogeneous velocity model. The temporal and spatial variances in seismic activities identify that the rock fractures in the dyke zone are closely related to the longwall mining process and a local dyke has a controlling influence on the stress concentration in its vicinity.

Apr 26, 2022

By W. C. Shanks

Metalliferous sediments and/or saline brines have now been discovered in numerous sea floor deeps along 900 km of the axial rift zone of the Red Sea (Fig. 1). The Atlantis II Deep remains the most interesting of the the brine deeps both in terms of intensity of submarine hydrothermal processes and in terms of potential economic importance. In fact, successful completion of a pre-pilot mining test in 1979 indicates that the Atlantis II Deep may become the first deep sea base metal sulfide mine (Mustafa and Amann, 1980). Under the most optimistic scenario, the Atlantis II Mine might be established 4-6 years after completion of a year long pilot mining test in 1983-84. If established, mining would produce about 100,000 tons per day of wet mud with about 200 tons per day contained zinc, and proportional amounts of Cu and Ag. Expected mine life would be about 15-20 years (Anon., 1981). In addition to direct economic importance, the Red Sea brines and metalliferous deposits provide significant insight into exploration for sea floor brine-related ore deposits and for analogous ancient deposits. In this paper I will concentrate on the economic potential of Red Sea deposits and sea floor exploration for brine related deposits, but some ramifications of relevance to ancient deposits are extant.

Jan 1, 1982

By J. A. Domenico

A safe and precise mineral separation alternative to heavy liquids is being used for mineral sands exploration on large scale orebodies. The separation process, Magstream®, uses ferro-fluids and magnetic and centrifugal forces to produce precise split points over a range of specific gravities from 1.5 to 18.0 g/cc. This paper describes a commercial scale exploration program treating, roughly, 90 samples per day in Senegal (West Africa). Separation results comparing Magstream® and conventional heavy-liquid separation are presented.

Jan 1, 1994

By A. E. Jack Swanson, Brian P. Micke

INTRODUCTION Nevada Goldfields began underground mining development at the Kingston Project in September, 1986, followed by mill start-up in March, 1987. The first gold pour in April followed three years of preparatory work in establishing a North American operational base for the production of precious metals by Golconda Minerals N.L., an Australian mining firm. GENERAL CORPORATE BACKGROUND The Golconda Group of companies was established in early 1983 in Australia. It began operations by successfully retreating tailings at several old gold mining sites throughout Australia. With the limited reserves available for tailings retreatment, Golconda began to look toward the future by conducting a gold exploration program in Australia. However, the continued high price of gold in Australia had limited the possibilities of acquiring good properties at a reasonable cost and consideration was given to looking outside Australia in addition to Golconda's domestic exploration activities. North America was favored because of the proven potential for substantial gold deposits, the established infrastructure which would allow for rapid and cost-effective development of new projects and the advantages of similar political and economic climates. In mid-1984, Golconda established an office in California and began an extensive study of over 100 prospects throughout the United States. Two prospects were identified as a result of this study whch showed merit; one was located at Empire, Colorado and the other at Aurora, Nevada. Negotiations were then successfully undertaken to acquire these two properties. Golconda's U.S. offices were moved to Reno, Nevada in early 1985 to facilitate management of its projects. To operate and manage these projects, a small Canadian company listed on the Vancouver Stock Exchange, Cannon Minerals, was acquired by Golconda and renamed Nevada Goldfields Corporation. The current structure of the company is shown below in Figure 1. A private placement of 2,575,000 shares of common stock at US54.00 per share was arranged by Jacksons Limited of Australia in association with W.I. Carr (U.K.) Limited of London. This placement resulted in US510.3 million being available in May, 1986 for the acquisition and initial development of the Aurora and Empire projects. While the financing was underway, project planning commenced on both the Aurora and Empire projects. The Aurora project was selected as the one to be initially developed because of its relatively advanced stage of development. The

Jan 1, 1987

By J. T. Winkelmann

The Mineral Park Mine is an open pit copper-molybdenum mine located in northwestern Arizona, approximately twenty miles northwest of Kingman, Arizona. The concentrating facility has been regarded, with the expansion in 2011, as a plant capable of treating fifty thousand short tons of feed per day for the mixture of supergene and hypogene ores available. The grinding circuit consists of two 32? x 14? SAG mills and four 20? x 28? ball mills. As ores became harder with greater depth in the adjacent pit areas, however, the SAG mills became severely throughput limited. The traditional treatment for similar properties is the installation of a recycle pebble crushing circuit. Because the cost of such an installation is quite elevated, and preliminary testing and research was inconclusive regarding the predicted throughput increases, management and technical personnel set out to find another solution to the problem. The result entailed a redesign of SAG lifters/liners and a nearly unique circuit change which was, at best, a difficult step that defied current grinding logic. This paper describes these changes, events leading up to them, and the results.

Feb 23, 2014

By Robert A. Blake

Introduction Sulfide copper, zinc and iron concentrates are recovered in the 5000 ton per day flotation plant operated by Cities Service Company at Copperhill, Tennessee. The heavy-sulphide ore is first ground to 50 pct. minus 200 mesh and a bulk concentrate floated. The bulk concentrate, over 60 pct. of the ore weight, is reground to 72 pct. minus 200 mesh and then treated in a selective flotation circuit to recover copper and zinc concentrates. The tailing of selective float is the iron sulphide material source for the manufacture of sulfuric acid and iron sinter. The valuable minerals in the ore are chalcopyrite, marmatitic sphalerite, pyrite, and pyrrhotite. A typical mineralogical analysis will be found in table 1. A typical material flowsheet will be found in figure 1. Shown in the flowsheet are a scavenger float on the bulk rougher tailing and a copper-talc separation unit. At times a lead-copper separation circuit has been run.

Jan 1, 1971

By J. T. Graves

Bauxite, dolomite, and magnesite are natural occurring minerals that are used extensively in the manufacture of refractory products. In addition, magnesia produced from seawater or brine finds its way into the production of refractories. All of these materials must be processed at high temperatures, 1500°C to 2200°C, to produce an intermediate raw material (refractory grain) , which can then be used in the final manufacture of refractory bricks and shapes. During the last 20 years, the major supply of refractory bauxite has been from Guyana, and at times the annual production has ranged up to 1,000,000 tons per year. More recently, China has become a major source of refractory grade bauxite by supplying over 300,000 TPY. Other sources of bauxite in lesser quantities have been Surinam, Brazil, and the U.S.A. During 1980, the estimated available world tonnage amounted to slightly more than 1,300,000 tons. The bulk of this material has been calcined in rotary kilns except for some of the Chinese production, which was treated in shaft kilns. Recent work has indicated that an excellent product can be produced in the Nichols Shaft Kiln using much less fuel than the conventional rotary kiln. Details of the Nichols Shaft Kiln will be provided later in this paper.

Jan 1, 1982

By E. D. Goddard

There are similarities, and differences, in the surfactants used in cosmetics and detergents. In both applications anionic surfactants constitute the major category. Their main function is to clean, i.e. remove grease and particulate matter from fibrous or hard surface substrates. Cationic surfactants are used for conditioning substrates. Nonionic surfactants can function as a substrate cleanser but are seldom used as such in cosmetics; however, selected non-ionics are often employed as a primary emulsifier. Several specialized nonionic surfactants are used as a secondary surfactant in formulations to promote foaming and emulsification. Specific examples and modes of action of surfactants will be presented.

Jan 1, 1988

By B. A. Ashley

In 2007, Rosebud Mining Company (RMC) opted to extend the reserve base of Tracy Lynne Mine by developing through a sandstone channel. The extension provided access to approximately 6 million additional recoverable tons (approximately 8 years of mining) which originally had been deemed inaccessible. An evaluation of the mine?s existing ventilation system, which was designed to meet the needs of the original limited reserve, concluded that two ventilation shafts would likely be required to adequately ventilate the projected workings in the expanded reserve. To assist in the evaluation, a ventilation model of the mine was developed using Ohio Automation?s ?ICAMPS MineVent? software based on field data from Tracy Lynne Mine, prior ventilation survey experience at similar RMC mines, and relevant published sources. Model results suggested that the most economical shafts would be an 8-ft diameter return and a 4-ft diameter intake. Unfortunately, issues related to property leasing and shaft site permitting caused construction delays. Therefore, the model was also used and proved to be effective in prioritizing interim ventilation upgrades which could be implemented in order to maintain coal production. Model results indicated that the best interim upgrades included rehabilitating restricted entries and damaged stoppings and replacing the main fan with a higher pressure fan. From late 2010 to mid-2012, all interim upgrades and shafts were implemented. Current models and mine experience indicate that ventilation will not be the limiting factor for mining the additional reserve.

Feb 23, 2014

By A. W. Khair

This paper presents a strength formula for the design of coal pillars. The formula is derived from results of laboratory experiments, studying the effects of primary factors influencing the strength of the coal specimens/pillars. Five primary factors, significantly affecting the strength characteristics of the coal specimens/pillars were identified and extensive laboratory investigations were carried out. The five primary factors were namely 1) coefficient of friction between loading platens and coal specimens, 2) elastic properties of the loading platens, 3) coal specimen geometry, 4) coal specimen size, and 5) rate of loading. Four to nine levels of variation for each primary factor on the strength of coal were studied. An empirical formula, implementing the variation of the primary factors affecting the strength of coal specimens/pillars, has been developed. A comparative analysis of the results provided by this and some well known formulae is also presented.

Jan 1, 1994

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

By E. O. Jacobs

A coupled solid and rock fracture mechanics model is used to analyze the blast driven fracture propagation phase, predict propagation rates, and directly measure shockwave and particle velocity. The study incorporates quasi-static pre-stress conditions for different depths below the surface. The scaled experiments include dynamic material properties and quasi-dynamic fracture mechanics which are shown to significantly affect the fracture propagation. The study was performed using three-dimensional cube-type laboratory models fabricated from Polymethylmethacrylate (PMMA). The test cubes are loaded with explosives and resulting fracture networks are studied. The dynamic evaluation of the spatial crack system is monitored using a high speed image camera. An experimental model set-up is designed to indicate the pre-stress effect on deep borehole blasting and is shown that the pre-stress conditions have a decisive influence on fracture profiles and orientation. It is found that shockwaves rapidly exceed the slower dynamic fractures and a majority of cracks occur due to detonation pressure. Experimental testing using different parameters validate that explosive fracturing can predict the outcome of fracture and crack propagation in any rock type with known material properties. This can be accomplished under great stress conditions deep below ground surface. The experimental study results can be applied to a variety of industries such as mining and quarrying, tunneling, oil and gas, and construction.

Feb 23, 2014

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk, T. Punt

This study investigated the performance of citric acid as lixiviant for cathode material from end-of-life lithium-ion batteries (LIBs). Black mass containing 84.2 weight percent MNC (LiNi0.45Mn0.4Co0.15O2) and 15.8 weight percent LCO (LiCoO2) material was leached at solid-to-liquid ratios of 20, 50 and 100 g/L. Leaching with 1.5 M citric acid, 2 volume percent H2O2 and a solid-to-liquid ratio of 20 g/L at 95 °C extracted 90 percent Co, 95 percent Li, 94 percent Mn and 94 percent Ni within 20 min. At the highest solid-to-liquid ratio of 100 g/L with 1.5 M citric acid, 10 volume percent H2O2 and 95 °C, 84 percent Al, 84 percent Co, 87 percent Li, 86 percent Mn and 96 percent Ni were leached after 40 min, producing a leach solution containing 0.68 g/L Al, 20.0 g/L Co, 6.0 g/L Li, 13.6 g/L Mn and 19.3 g/L Ni. Using stepwise addition of H2O2, instead of initial bulk addition, did not significantly improve the leaching efficiency but did reduce the required leaching time. Temperature control of the reactor was also more manageable with stepwise addition of H2O2, and evolution of gas was less vigorous. It was observed that the leaching efficiencies of Co, Li and Mn decreased slightly at solid-to-liquid ratios of 50 and 100 g/L, while the leaching of Ni increased slightly. The solution leached at 20 g/L could be stored for six weeks without any spontaneous precipitation. However, solutions leached at 50 and 100 g/L showed changes in concentration after one month of storage, suggesting that processes that have a large material throughput and use high solid-to-liquid ratios around 100 g/L must ensure that the solutions are not stored for extended periods of time.

Apr 1, 2025

By J. Hanna

The University of Alabama Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of carbon-ate gangue from sedimentary apatites "francolite" in the pH range of 4-6 without collector conditioning of the pulp. The process, which does not require an apatite depressant, was modified to beneficiate a high Mgo siliceous phosphate matrix from south Florida. The modified process includes two flotation stages, one for carbonate removal, as mentioned above, and the other for phosphate recovery from the siliceous gangue. The selective flotation separation of the carbonate and phosphate, from siliceous constituents of the matrix at various pH levels and collector dosages are discussed. In the carbonate flotation stage, about 70% of the Mgo was rejected in the froth and the phosphate flotation stage produced concentrates analyzing about 31% P2O5,0.7% HgO and 4% insol. The overall P2O5 recovery in the two stages is about 85%.

Jan 1, 1989

By O. Salami, G. Xu

Fire accident is one of the most classic safety concerns in underground mines both in the USA and abroad. It may occur from pool fires due to leakages in hose or pipes, vehicle fires, or fires in tires and conveyor belts in the underground mines. It may also result from the storage of flammable materials such as gasoline, diesel, and explosives in the underground. When fire occurs in an underground mine, it releases heat, smoke, and other toxic gases such as carbon monoxide, and methane to the surrounding thereby making life unbearable to the miners. Furthermore, smoke greatly impact visibility in the underground which makes evacuation even more onerous and challenging. To this end, a thorough investigation of fire behavior and spread of toxic gases in a practical underground mine is imperative to develop a reliable emergency evacuation plan in an event of fire disaster in the underground mine. The objective of this study is to investigate temperature variation and CO spread along mine airways by conducting full-scale fire experiment in the underground mine. The results presented from this study are crucial to developing evacuation plans in underground mines. In addition, the findings from this study could be used to validate existing evacuation models.

Mar 2, 2022

By A. J. Getz

The paper reviews the status of the major precious metals projects in Australia, Papua New Guinea, Indonesia, the Philippines, and New Zealand. The projects may be at the stage of exploration, development, operation, or expansion. The paper covers project location, reserves, method of resource exploitation, anticipated production, and other unique conditions.

Jan 1, 1990

By Connor Meinke, Shaihroz Khan, Kevin Erwin, Rajiv Chandramohan, Muhammad Usman Siddiqui

A geometallurgy study aims to link metallurgy and geology to reduce technical risk and enhance the economic performance of a mineral-processing plant. It does so by accounting for variability in a deposit to develop cash-flow models with variable throughput rates. High-quality sample selection for metallurgical test work that is representative of the deposit is an essential component of a geometallurgy study, but the large multidimensional data set makes sample selection a daunting task, as classifying the data set while respecting its heterogeneity is difficult. This paper presents a streamlined approach for sample selection, using statistical analysis techniques in Python. It cuts down time to select samples from around 1,200 s per drillhole to about 60 s for data classification and from 12 h to 8 h for handpicking samples from the classified data set, translating to cost savings. The cumulative sum method and k-means clustering method are used in the methodology to elegantly classify the data and select representative samples. The effectiveness of the methodology is demonstrated by presenting data from a prefeasibility study of a copper-iron mine in which 40 samples were selected for flotation test work.

Dec 1, 2024

By W. G. Pariseau

"BACKGROUND The Crandall Canyon Mine (CCM) is located in the Wasatch coal field in central Utah. Extensive longwall mining at CCM preceded a decision to recover coal left in barrier pillars on each side of a set of main entries extending far into the mine. During mining in March, 2007, a major bump occurred that led to cessation of mining in the barrier pillar on the north side of the mains and to begin mining in the south barrier pillar. Subsequent loss of ground control in August, 2007, through coal pillar bursts had tragic consequences with loss of six miners and shortly afterwards three rescue team members. An MSHA report describes the events in detail (MSHA, 2008). An important lesson to be learned from CCM is the need to select a computer program suitable for pillar design. Computer programs are engineering tools; selecting the right tool for the job is essential. In this regard, a minimum program requirement is capability for computing stress distribution within a pillar and adjacent roof and floor strata. The reason is simple: strength of rock is stress dependent; both vary from point to point in pillars and adjacent strata. Preferably, one should follow the evolution of stress as the mining plan is executed from start to finish to assure safety or to warn of a potentially hazardous situation developing as mining progresses. The approach to the problem posed by barrier pillar mining at CCM is conventional in the sense of applying well known finite element modeling techniques to analysis of a proposed mining plan. The engineering purpose is to evaluate the mining plan with respect to ground control questions including roof, floor and pillar safety. Results of previous two dimensional finite element analysis indicated pillar safety was by no means assured (1, 2, 3). Geometry of barrier pillar mining is limited in two-dimensions, for example, crosscuts are not seen in vertical cross sections. While three dimensional analyses are preferred, even moderately sized regions often lead to very large problem sizes that exceed computer capabilities. However, a recent development in finite element modeling of tabular deposits allows for whole mine analysis in three-dimensions. This technique involves a dual node – dual mesh concept. Both have been used separately in much earlier work, but are only now are used in combination. Estimation of subsidence at a kilometer scale and details of stress, strain and displacement about barrier pillars, main entries and pillars, and so on at a meter scale are possible (4). No compromise involving empirical formulas or similar guess work is required. Indeed, all calculations are based on first principles: physical laws, kinematics, and material laws. Effects of joints and in situ variability or uncertainty in strata properties, elastic moduli and strengths, may be included for greater realism. An important objective of the present study is to assess the role of three-dimensional pillar geometry in arriving at conclusions regarding barrier pillar mining versus two-dimensional results."

Jan 1, 2015

By L. Zhou, D. Bahrami

Mine ventilation is one of the most important aspects of mining operations in underground mines. It is critical to maintain and deliver required fresh air to the active areas to reduce the risk of overexposure to hazardous contaminants or explosive atmospheres. An unexpected or unknown event such as roof collapse, unexpected mine door closure/opening, a fire/explosion, or fan malfunction could adversely alter the airflow distribution within the mine ventilation network that could lead to a hazardous underground environment. Knowing the occurrence and location of such an incident is of critical importance. In this study, the authors developed a novel methodology to assist mine operators in quickly identifying the location of any abnormal airflow change within the network using the airflow changes at monitored airways. The concept is based on a direct derivative method developed by the authors. This paper provides the details of the developed method as well as numerical verification examples. The application of this method can benefit mine operators and safety personnel in making better decisions during a mine emergency response operation to mitigate hazardous conditions arising from an unexpected airflow disturbance

Mar 2, 2022