Search Documents

Controlled blasting experiments in small development drifts were conducted at CANMET's Experimental Mine, from August 1992 to November 1993. The objective of these experiments was to develop suitable controlled blasting techniques for small development headings drilled by jackleg with 32 mm diameter holes. The experimentation also aimed to provide insight into blast damage mechanisms. Particular attention was given to the physical-mechanical properties of the rock and the rockmass structural data in order to make the results applicable to other geological environments. The drift faces were approximately 2.4 m by 2.4 m with 36 to 43 holes drilled to a depth of 2.4 m. Cartridged water gels, emulsions and semigelatin dynamite were used in the cuts and as primers, ANFO as the main explosive and decoupled 19 mm diameter semigelatin dynamite charges were used in the perimeter holes. Smooth blasting techniques and pre-splitting were tested in the underground mine. All the blasts were monitored with a multi-channel blast vibration monitor to which was attached sets of high frequency geophones and accelerometers. This first set of experiments has illustrated the efficiency of con-trolled blasting techniques to reduce blast damage and demonstrated the need for further research to improve the safe and efficient use of explosives.

Jan 1, 1995

By A. E. Isaacson

The U.S. Bureau of Mines is investigating a systems approach to metals recovery from leach liquors produced by in situ leach mining techniques. A successful in situ leaching process requires a thorough under-standing of the complex interrelationships that exist between leaching chemistry and metals recovery. Laboratory research is addressing these interrelationships in the solution mining of a copper oxide deposit. Laboratory tests have been conducted to gather baseline data related to the design and operation of continuous leaching-solvent extraction-electrowinning circuits. This paper addresses the findings of the baseline studies. Specific results include the characterization of simulated in situ leach liquors produced by leaching chrysocolla and chrysocolla-atacamite-bearing copper ores. Metal recovery procedures, utilizing four commercial solvent extraction reagents, are also characterized, and potentially troublesome leach liquor contaminants that may complicate waste management procedures are identified.

Jan 1, 1990

By P. B. Queneau

An operating problem encountered at the Moa Bay operation in Cuba, where nickeliferous laterite ore is processed by sulfuric acid pressure leaching, is the formation of alunite and hematite deposits on the autoclave walls. The AMPX Extractive Research & Development, Inc., metallurgical laboratory (Golden, Colorado) has made substantial improvements in the Moa Bay process in the areas of metal recovery, energy consumption, and feed versatility. One of the advantages of AMAX's process is its ability to treat substantial portions of nickel- and magnesium-rich serpentine while maintaining acid utilization efficiency. The process minimizes scale formation by combining staged acid addition with vigorous agitation and 270°C operation, but does not eliminate scaling. This paper describes how advantage can be taken of MgSO4?XH20 precipitation both to inhibit alunite scaling and to disperse hematite scale within the MgSO4?XH20 matrix. Cooling the autoclave from its 270°C operating temperature down to 180°C takes advantage of the reverse solubility of magnesium sulfate. The magnesium dissolves, liberating entrained hematite, thus providing a means for control of autoclave scale with minimum process disruption.

Jan 1, 1984

By Wayne Wride, Amy Lamb, Debra Sonntag

In today's "information age", we have the ability to collect volumes of data about a company's performance. The challenge is to turn that data into information employees can understand and use to fine-tune equipment, modify work processes, and ultimately manage production. Software programs have increasingly given end users control over what data is used and how it is presented. Kennecott has implemented an information system capable of collecting and storing data at the primary level. This enables plant personnel to transform historical data into information for action. Kennecott plans to expand its data collection and use trending and reporting capabilities to move toward a fully optimized operation.

Jan 1, 2000

By Keith G. Wallace

The effect of face resistance on ventilation air leakage through stoppings was measured in a twin development heading. Face resistance was varied by alternately tightening or loosening the face line brattice to change the line brattice leakage. Results indicated that tight brattice lines are necessary to maintain acceptable airflow at the face but result in higher leakage throughout the entire system, reduced overall ventilation efficiency, and higher operating costs. Conversely, a low face resistance which simulated an auxiliary fan/duct system gave reduced stopping leakage losses, higher quantities of air at the last open cross-cut and greater entire system efficiencies

Jan 1, 1984

By Z. Yunquan

The flocculation and dispersion behaviors of microsize wolframite and quartz are systematically studied in this paper. For synthetic mixtures, the floc separatory method on gravity units--electromagnetic vibration table (EVT) and lifting column (LC), have been approached. Satisfactory results can be obtained with a weak shearing. A better metallurgical performance can also be achieved for natural ore slimes through the combined technique. The efficiency is better than that of single gravity separation. Finally, the mechanism has been investigated.

Jan 1, 1990

By D. M. S. Bhatia

Five sulfide minerals from the Magiwnt mine, southeast Missouri were analyzed for 31 trace elements in over 300 samples by laser microprobe spectrographic analysis of polished sections. The concentration of several trace elements shows a pattern of progressive variation with depth (space) and variation with different paragenetic stages (time) of each mineral. Factor analysis of the geochemical data shows sympathetic correlation both in space and in time of Bi, Cd, Ge, and Sn in galena and sphalerite, and Ni and Co in sphalerite and marcasite.

Jan 1, 1979

By Stewart R. Wallace

In the spring of 1959 while visiting the offices of the US Geological Survey (USGS) in the Denver Federal Center, I had a chance encounter with Paul Theobold, a former but, at that time, casual associate. Paul mentioned to me the results of his work on stream sediment geochemistry (Theobold and Thompson, 1959). Using panned concentrates, Theobold and Thompson had discovered a tungsten anomaly in Clear Creek and followed it upstream to its source on Woods Creek, a small tributary to the West Fork of Clear Creek. The specific source was a debris cone about 0.8 km (0.5 mile) upstream from the mine yard at the Urad molybdenite deposit. Because of the genetic and zonal association of tungsten and molybdenum at Climax, I found this very interesting. Accordingly, I related this information to Robert Henderson, general manager of western operations for Climax, and asked his permission to do some follow-up work. He, in turn, telephoned Frank Coolbaugh, the president of Amax, telling him of my interest and saying that, "Climax would take care of it." On my first visit to Urad, my companions (Dave Jonson, Bruce MacKenzie, and Dick Baker) and I were confronted by a "Cousin Jack" caretaker who made up for his diminutive stature by a "pistolover" that hung down almost to his knee and by a watchdog that was one-half wolf and one-half mean sled dog. We retreated discretely to Clear Creek and then climbed up the "back" side of Red Mountain by separate routes, across the ridge crest, and part of the way down the "front" side, sampling as we went. Although much of the ground was covered with snow, we found lots of puzzling but friendly looking rocks and the geochemical results were interesting. A geologic map of central Colorado showing the location of the Urad-Henderson and Climax deposits is shown in Fig. I.

Jan 1, 1991

In this paper, a number of novel hypotheses that provide a fresh perspective on the characterization of strata movements associated with longwall mining are developed by analyzing subsidence measurements with an influence- function-based computer program. With this influence-function technique, easily obtained surface displacements can be used to determine some of the complicated, expensive, and difficult to measure movements of the immediate roof strata in a longwall panel. The primary hypothesis developed by this analysis proposes the existence of an area of partial roof caving near the edge of a panel called the "edge effect." A second hypothesis, interrelated with the first, promotes the importance of the effect of gate-entry closure on the observed strata movements. Both the primary edge effect hypothesis and the secondary hypothesis concerning gate-entry closure are justified and quantified in an extensive analysis of surface subsidence that uses supporting information from related theories, design criteria and insitu measurements. Next, the edge effect and the gate closure hypotheses are extended further and used to provide an explanation of the complex subsidence interaction of adjacent longwall panels in what is termed a "redisturbed" effect. Finally, in the conclusions of this paper, the importance of accurately understanding these longwall strata movements for proper subsidence prediction or gate design is stressed.

Jan 1, 1986

By Arthur B. Cummins

It is appropriate to discuss diatomite at an AIME meeting in San Francisco. California has led the nation, and the world, in the production of diatomite products for more than 40 years. It appears that our State will maintain this position for a long time to come. Diatomite today ranks high in the list of California mineral commodities, with a total value since 1889 well in excess of $100 million. California's production has more than doubled since 1942. In 1959, the value of diatomite production in California is exceeded only by the following industrial mineral materials-borates, stone, sand and gravel and cement20,28. Also, not unimportant is the production of diatomite in each of our other Pacific Coast States, including Nevada. First, let us define diatomite. It is a sedimentary siliceous rock of organic origin, which consists mainly of the fossilized remains of diatoms. Diatoms are microscopic aquatic plants which have the capacity of precipitating silica bio-chemically so as to form a part of their organized structure. In the economic sense, we are not concerned with the numerous types of sedimentary materials which contain minor amounts of diatom residues, or with impure or highly indurated siliceous materials, which may have been formed from diatomite2. Diatomite (synonyms--diatomaceous earth, kieselgurO is a term generally restricted to material of such qualities as to be suitable for commercial uses. Diatomaceous silica is a designation which is best used to distinguish the basic component of diatomite, that is, the substance of the silica shell itself, and which is the major' constituent of beneficiated diatomite or processed diatomaceous products.

Jan 1, 1959

By F. F. Peng, Y. Xia

In modeling of hindered-settling bed separators, the published separation mechanisms are based on differences of particle density and size distributions, without the details of complexity of particles-liquid interactions. A fluid dynamic model for the separator is developed using Euler-Lagrange approach of Computational Fluid Dynamics (CFD). Fluid motion is obtained from solving the movement of liquid governing equations. The damping effect on flow pat-terns caused by the movement of particles resulted in liquid-particle coupling is included in the model. Effects of particle size, and particle density compositions, feed rate, feed water flow rate, upward fluidizing water flow rate, etc., are simulated in the 2-D separation model. Flow pattern effects on the separation of fine particles in the separators with center downward-flow and side cross-flow feed systems are investigated.

Jan 1, 2004

By Morgan M. Sears, Mark Morris, Joseph Bright

In an effort to advance the science underlying modern coal pillar stability analysis, researchers at the National Institute for Occupational Safety and Health are currently involved in research aimed at better understanding the impact of an in-seam rock parting on the strength of coal pillars. The purpose of this study is to determine a suitable virtual mining height that could be applied using current pillar stability analysis tools. To accomplish this, the boundary element model LaModel was used to back analyze data collected on pillar performance in a room-and-pillar panel at the Maple Eagle Mine located in Southern West Virginia. In a previous work, data collected from borehole pressure cells (BPCs) and extensometers were taken from three instrumentation sites. Data collected from the back bleeders were used to measure the rear abutment stresses, and data collected from two instrumentation sites in the wraparound bleeder were used to measure the front and side abutment stresses as well as the peak strength and performance of the slabbed leave pillar. The utilization of two nearly identical instrumentation sites in the wrap-around bleeder provided much needed repeatability of the obtained measurements. In this study, the data collected from BPCs at the three instrumentation sites was calibrated to match the Bieniawski pillar stress gradient. To model the measured pillar behavior, the LaModel program was selected due to its capability of being directly comparable to the Analysis of Retreat Mining Pillar Stability (ARMPS) and Analysis of Coal Pillar Stability (ACPS) programs. The model was then calibrated to match the measured abutment extent and abutment stress. Finally, the model was validated by reducing the modeled mining height until the yielding of the slabbed leave pillars in the model matched what was measured in the field. The final calibrated mining heights show that a reduction of the shale parting thickness, not including any clay layers, of 52% is applicable. This research study provides the first known measurement of the ARMPS/ACPS “50% Rule” and its applicability to this panel of the Maple Eagle Mine. This finding provides a proof of concept and could have significant implications for future research.

Feb 1, 2024

By K. S. Olson

My reaction when first asked to present this paper was; "What could I possibly say that would hold the audience?s attention for 15 minutes? What could I offer that anyone familiar with the Nevada Barite Industry wouldn't already know?" Well, quite frankly I can't. The industry has certainly been anything but exciting for the past 10 years and, in fact, quite depressing. The challenge, for those few of us left in it, has been to keep it alive. At times it has felt like a doctor must feel with a terminally ill patient. All I can do is recap the past ten years, review the present state of the industry, and offer a few personal opinions and observations as to where I think we are headed.

Jan 1, 1993

By Thomas H. Dubaniewicz

(XP) enclosures to enclose electrical ignition sources to prevent propagation of an internal methane-air explosion to a surrounding explosive atmosphere. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a lithium-ion battery thermal runaway test within a modified MSHA-approved XP enclosure to assess thermal runaway containment. Thermal runaway produced jet flames emanating from the cover joint at several locations and distorted the cover joint and bottom plate of the enclosure beyond allowable limits. The test demonstrates that XP enclosures may not provide adequate explosion protection against lithium-ion battery thermal runaway. This paper suggests some approaches to mitigate the hazard.

Feb 1, 2024

By Kanaan Hanna, Mir Heydari, Dipack Sengupta, Gordon B. French

This article, first in two, discusses the safety, technology, and economic impact of eliminating safety fuse from metal and nonmetal mines. It is based on operation and manufacturer experience over the past five to 10 years. If safety fuse is eliminated, blasting accidents will decrease. There should be only limited technical impact. The economic impact will be minor for large operations, but will be significant enough for small operations that some will likely close rather than change. Most mines would probably change over, with the market absorbing the extra cost. Elimination of safety fuse would obviously have an impact on the two safety fuse manufacturers. One manufacturer produces an alternative system and would be unaffected. The other, however, will be affected if it does not change its production strategy. From the standpoint of employment and production, abolishing safety fuse will have a very minor effect on the mining industry as a whole. This article discusses the current use of initiation systems, incidence of accidents, and fuse consumption. Next month, part two describes the economic impact of eliminating safety fuse on the mining industry and manufacturers, and presents an economic analysis of the initiation systems. Introduction The objective of this study was to determine the safety, technology, and economics of eliminating safety fuse from metal and non-metal mines. There were five major tasks: • Studying initiation-related accidents from the Health and Safety Accident Center (HSAC) data file; • Visiting mines, collecting relevant data, and interviewing mine operators; • Establishing the trend in safety fuse consumption and type of users; • Corresponding with fuse manufacturers, domestic and foreign; and • Developing an idealized blasting cycle to evaluate the possible economic impact of safety fuse elimination on large and small operations. More than 450 explosives-related accident reports have been screened and analyzed by investigating HSAC files. These reports have been studied and classified according to the four initiation systems, size and type of mines, and time and frequency of accidents from 1973 through 1978. Twenty-four mining operations were visited to obtain supporting data for this study. Mine personnel were interviewed to determine attitudes about safety fuse and alternative detonating systems. This article decribes available data. It also attempts to provide information that can be used to answer such questions as: • Is the use of safety fuse (an antiquated detonation system) a major cause of mining accidents? • Are alternative systems available that could result in fewer in-juries to miners?

Jan 1, 1984

By Thien Sok, Yaojun Lu, Craig Gilbert, Jeremy Scott

Feedwells play a pivotal role in gravity thickeners, governing flow distribution, feed dilution, and flocculation condition during solid–liquid separation. This study presents an optimized design and digital prototyping framework for FLSmidth’s E-volute and E-Duc Feedwell systems, integrating advanced computational fluid dynamics (CFD) with quantitative criteria introduced at SME2024. Building on established FLS technologies, a series of novel configurations were developed and systematically assessed under full-scale and site-specific conditions. CFD provided quantitative insight into flow distribution, feed dilution, and flocculation efficiency, enabling iterative refinement of design parameters. The optimized feedwell demonstrated superior hydraulic performance, enhanced mixing, and improved flocculation outcomes. Beyond the specific design advances, the work highlights CFD as an effective and economical tool for digital prototyping, facilitating early identification of design limitations, reducing dependence on physical trials, and accelerating innovation. The methodology underscores the value of simulation-driven design in advancing feedwell performance and improving thickener technology.

Feb 22, 2026

By Jürgen. F. Brune, CLAIRE STREBINGER, ADITYA JUGANDA, Gregory E. Bogin Jr

The abstract highlights the risk of methane gas explosions in underground coal mines and the potential of computational fluid dynamics (CFD) modeling to simulate such events and assess their impact on mine ventilation. The study focuses on developing CFD models for large-scale explosions in longwall mines, specifically simulating methane gas explosions resulting from face ignition during coal cutting. The research demonstrates the integration of a combustion model into a longwall mine ventilation model and shows how the availability of explosive gas mixtures significantly affects flame propagation and explosion pressure.

Mar 27, 2022

By Mathew Cook

Technological developments in Distributed Fiber Optic Sensing and improvements in both hardware and software have allowed fiber optic sensing systems to be deployed in a variety of applications such as pipeline leak detection, perimeter security monitoring, and power cable real time thermal rating. Recently, there has been a larger adoption of monitoring of conveyor belts in so called Conveyor Health Monitiring Systems (CHMS) within the mining and bulk material handling industries to identify idler conditions on an ongoing basis. Several attempts have been made to institute sensing capabilities into conveyors with mixed success. However, recent breakthroughs in modeling, installation methodology, and technology, as well as increased understanding of application and industry requirements, have allowed the technology to be deployed at both experimental and commercial scales. This paper summarizes the application conditions and requirements, design considerations, methodologies used, the outcomes achieved, the logistical and field considerations, and the future possibilities of the use of this technology in CHMS using Distributed Fiber Optic Sensing.

Feb 22, 2026

By E. Woodburn, H. W. Smith, M. C. Fuerstenau, R. Putman

This paper presents a review of developments to date in computer control practice, based in large part on Canadian experience. The basic problem examined is that of stabilizing control; matters considered are control strategies, hardware and software aspects of system implementation, reliability, human factors, and economic results.

Jan 1, 1976

By William J. Lang

In just over a generation, the United States bentonite industry has grown from almost a rake and shovel operation into one with a multimillion ton annual production rate and exports to all corners of the globe. Bentonite production, pressed to keep pace with the soaring demand, has increased more than 10 fold in the last 30 years. The worldwide demand for bentonite is expected to double during the next eight to ten years. It remains to be seen whether U.S. producers will be able to maintain the dominant position in the world market. It should be noted that accurate statistical information regarding production or market information is difficult or impossible to obtain abroad and also within the United States. Published information obtained in response to questionnaires of the Bureau of Mines tends to be on the conservative side. FOUNDRY It has only been in the last thirty or forty years that bentonite has become an indispensible part of the age old metal casting industry. The relationship has proven most beneficial to both industries and promises to be long lasting. The foundry market for bentonite was the least of the three major markets twenty years ago but now leads all others and consumes 1/3 or more of the

Jan 1, 1971