Search Documents

By W. K. Katoto

The Tailings Leach Plant (TLP) of the Zambia Consolidated Copper Mines Ltd at Nchanga was commissioned in 1974 as the world's first largest successfully operated agitation leach SX-EW plant for copper production. The design, development and operation of the plant soon after commissioning termed as TLP stage II has been described by Holmes et al (1). In the initial phase the plant was designed to treat approximately 25,000 tonnes per day of current flotation tailings from the Nchanga Concentrator operations, and had a design capacity to produce 75,000 tonnes per annum of copper. Further expansion took place in 1986, and TLP stage III was successfully commissioned to treat an additional 20,000 -25,000 tonnes per day of large reserves (over 135m tonnes) of reclaimed tailings stockpiled since the early 1930's in four paddock type tailings dams (T01 to T04). The salient feature of TLP stage III expansion described by S K Mwenechanya et al (2 -3) was the installation of the world's largest Horizontal Belt Filter Plant with 26 filters each of 80 m2 filtration area.

Jan 1, 1996

By P. Zhang, S. Al-Thyabat

"Phosphate rock contains traces of rare earth elements (REEs) and can be a secondary source of these critical materials as large tonnages of phosphate rock are mined annually. Attention has mostly focused on the extraction of REEs from phosphogypsum, which contains more than 70 percent of the REEs reporting to phosphate concentrate, with only limited work conducted on REE extraction from sand tailings and slime even though they account for 16 percent and 15 percent, respectively, of REEs mined with phosphate matrix.In this work, phosphate flotation tailings were upgraded by gravity separation and froth flotation. Gravity separation was conducted using a laboratory shaking table, while flotation was conducted in a Denver D-12 flotation cell. The concentrated tailings were then leached by nitric acid followed by REE extraction with solvent and ion-exchange resin.The sand tailings were assayed as having 2.6 percent phosphate (P2O5 ) and 198.1 µg/g REEs. It was found that the shaking table could produce tailing concentrate assayed as having 8.6 percent P2O5 and 616 µg/g REEs but with only 20 percent REE recovery, while the froth flotation produced froth concentrate assayed as having 8.1 percent P2O5 and 368.2 µg/g REEs with 63.5 percent REE recovery. Leaching the flotation concentrate with 5.2 M (25 percent) nitric acid followed by extraction with solvent and ion-exchange resin yielded precipitates with REE contents of 0.926 and 0.314 percent, respectively, compared with 0.716 and 0.213 percent when table concentrate was used.IntroductionRare earth elements (REEs) consist of a group of 17 elements: the 15 lanthanides along with yttrium (Y) and scandium (Sc). They are rare not because of their scarcity in the Earth’s crust but because they are rarely found in economic and mineable deposits. REEs are called “seeds of technology” because of their importance to some critical technological industries such as renewable energy, hybrid cars, electronics and batteries. On average, an electric car or a hybrid car contains about 10 kg of REEs (Grasso, 2012; Radhika et al., 2011).REEs are usually categorized into light (LREE) and heavy (HREE). LREEs consist of lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pr), samarium (Sm), europium (Eu), gadolinium (Gd) and scandium (Sc), while HREEs consist of terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), lutetium (Lu) and yttrium (Y). About 200 minerals contain traces of REEs, but only three are considered economically significant: bastnasite, with the formula La,Ce(CO3)F; monazite, with the formula(Ce,La,Nd,Th)PO4; and xenotime, with the formulaYPO4 (Jordens, Cheng and Waters, 2013)."

Jan 1, 2016

By K. A. Natarajan

Platinum electrodes are not inert as originally thought to be. The reactivity of platinum electrodes can explain their erratic behavior in many electrochemical measurements of metallurgical interest, e.g., in flotation systems, streaming potential measurements, contact-angle measurements, and in leaching systems. The anomalous behavior of platinum electrodes in redox potential measurements in aqueous systems was studied through Eh and pH measurements in water-oxygen, iron-water-oxygen and manganese-water-oxygen systems. Stability relations between Fe++ and Fe(OH)3 and between Fe(OH)2 and Fe(OH)3 were studied to judge the correspondence between experimental and theoretical equilibrium lines. The practicality of redox potential measurements in estimating ferric-ferrous ratios in aqueous systems was investigated along with their suitability as indicators in leaching operations, e.g., the removal of iron by aeration from manganese leach solutions.

Jan 1, 1970

By Ahmet Tezcan, Zeki M. Dogan, Yalçin Kaytaz

Autogenous grinding in Turkey was first applied to quartzite where the mill is grate discharge type with an internal diameter of 2.99 m, having a length of 3.20 m and a capacity of as to 11.0 tons per hour. The second autogenous grinding was applied to a copper ore at Murgul Cakmakkaya Flotation plant of (KBI) Black Sea Copper Works having three mills 26 feet in diameter and 10 feet in length in close circuit with hydrocyclones. Recently, alterations were made in grinding circust by adding pebble mills. Furthermore, rubber liners and lifter bars were introduced pebble extractor and classifier were new features in the primary mills and circulating load was reduced by 20-50 tons per hour. At the end of these charges, capacity of each mill line was increased to 48 tons per hour with a full capacity of more than 9000 tons per day. Thirdly, autogenous grinding has been executed successfully on the slags of Samsun Smelting Plant of (KBI) Black Sea Copper Works with a mill of 20 feet in diameter and 6 feet on length having pebble mill following autogenous grinding.

Jan 1, 1992

By A. J. Stewart, M. Guay, J. W. Critchfield, A. P. Hoddeson

The MetroWest Water Supply Tunnel project includes three main work shafts, excavated primarily in rock. Shaft L is 9.8 m (32 ft) diameter and 124.1 m (407 ft)deep. Shaft E is 7.0 by 12.8 m (23 by 42 ft) and 91.4 m (300 ft) deep. Shaft 5A is 7.9m (26 ft) diameter and 72.5 m (238 ft) deep. Construction methods are compared and contrasted. Lessons learned involve a differing site condition in soil overburden, contractor-proposed modifications, and remedial slurry wall work. Other aspects discussed include noise and vibration control, groundwater inflow, water treatment, muck handling and contract administration issues.

Jan 1, 1999

By R. Hogg

A standard procedure for determining size-specific gravity distributions of fine coal (including the -400 mesh fractions) by sieving and centrifugal sink-float separation is described. The significance of using a centrifugal sink-float technique and the effect of the magnitude of the centrifugal force on the separation of fine coal are confirmed in the present study. The relative merits of cumulative versus incremental sink-float are discussed. The procedure is evaluated quantitatively using data obtained for the products of froth flotation of -100 mesh coal.

Jan 1, 1994

By Robert L. Grayson

An application of goal programming (GP) in evaluation of proposed purchases of major mining machinery is presented. It incorporates historical operating data compiled on mechanical delays to production time. The goal programming technique, which is an extension of integer programming, is used to maximize an objective function. The objective function combines the capital budgeting evaluation methods of net present value, payback period, profitability index, and total net earnings as goals weighted according to a management preference. The GP method gives an optimal solution to a multiple-goal problem. A sensitivity analysis is performed to determine the effect of an increased production forecast or a tightened budget on proposal selection.

Jan 1, 1982

By Xinyang Wang

It is believed that sulfur and volatile matter contents in coals are the main intrinsic properties to cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal's self-heating should be quantified. This study is aimed to improve the previous mathematical model developed by the authors for studying the coal's propensity for spontaneous combustion. It enhances the model's ability to consider the effects of sulfur, volatile matter and moisture contents in the coal - three important factors affecting the coal's self-heating process. Sulfur exists in coal primarily in the form of pyrite which will be oxidized rapidly under suitable conditions. Volatile matters, higher in low rank coals, are more easily to be oxidized. Heat of water condensation provides initial energy for low temperature oxidation. Heat release rates for pyrite oxidation and moisture condensation are built in the model. Finally, the simulation results in terms of time versus temperature on pyrite oxidation and moisture condensation are validated with the adiabatic testing data respectively.

Jan 1, 2013

By T. W. Martin

The use of conveyors in large, open pit mines and their drawbacks are discussed. Technological developments such as long distance conveyors capable of handling large rocks are explored. The development and testing by the Bureau of Mines of a prototype crib and cable conveyor for handling large rocks are discussed, and possible modifications of the concept for a production model are examined.

Jan 1, 1984

By Joseph Goessling, Mark Kroncke, James Parkes

The I-35 Capital Expressway (CapEx) Central Drainage Tunnels will serve as a stormwater collection system for the forthcoming I-35 Capital Express Central reconstruction project through downtown Austin, Texas. The schematic level concept design included three tunnels, 10 to 14 ft ID, totaling 26,000 LF. Constructability reviews during design development indicated issues with the concept design including phasing of construction, conicts with future retaining walls, staging area concerns, and signicant mixed face tunneling. The design was updated to mitigate these risks. The revised design includes two tunnels, both 22-ft ID and totaling 33,000 LF, that will be mined almost entirely in rock.

Jun 23, 2024

By R. Bhaskar

The control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. The understanding of the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of the existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been attempted. In this paper, first a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It incorporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.

Jan 1, 1985

By D. Bahrami, W. K. Asante, G. L. Danko

It is prudent to interpret atmospheric monitoring signals in real time for checking the safe limits of the air conditions in underground mines. In gassy mines, real-time evaluation increases the safety of operations. In all mines, continuous monitoring and evaluation contributes to maintaining air conditions within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase in hazardous contaminant concentrations can be predicted by signal pattern recognition, root cause analysis of rapid changes toward deterioration, and forward prediction in time using algorithms and numerical models. The paper describes an early warning system for analyzing monitored signal patterns continuously in real time as well as forward predicting the various environmental and working conditions to recognize dangerous trends that may affect safety and health in underground mines. A dynamic, numerical ventilation model with heat and gas contaminant simulation components is used for the analysis of atmospheric data. Methods and test results are discussed with numerical examples for signal propagation prediction. Several mine examples are studied using controlled, synthetic data for malfunction simulations to evaluate time delays between the detection time of suspicious signal trends and the time of dangerous threshold crossing marking an accident scenario. Delay time is found in the order of 20 min in the examples, signifying the useful time period for preventive intervention between EWS warning and the likely breakout of a following accident.

By D. Bahrami, W. K. Asante, G. L. Danko

It is prudent to interpret atmospheric monitoring signals in real time for checking the safe limits of the air conditions in underground mines. In gassy mines, real-time evaluation increases the safety of operations. In all mines, continuous monitoring and evaluation contributes to maintaining air conditions within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase in hazardous contaminant concentrations can be predicted by signal pattern recognition, root cause analysis of rapid changes toward deterioration, and forward prediction in time using algorithms and numerical models. The paper describes an early warning system for analyzing monitored signal patterns continuously in real time as well as forward predicting the various environmental and working conditions to recognize dangerous trends that may affect safety and health in underground mines. A dynamic, numerical ventilation model with heat and gas contaminant simulation components is used for the analysis of atmospheric data. Methods and test results are discussed with numerical examples for signal propagation prediction. Several mine examples are studied using controlled, synthetic data for malfunction simulations to evaluate time delays between the detection time of suspicious signal trends and the time of dangerous threshold crossing marking an accident scenario. Delay time is found in the order of 20 min in the examples, signifying the useful time period for preventive intervention between EWS warning and the likely breakout of a following accident.

By H. X. Li, A. Correa, M. M. Zhang, W. Xuan, M. Andrade

"With increasing demand for steel and depletion of high-grade iron ore deposits, more research efforts are being directed toward extending the life of existing ore reserves and developing technology to treat low-grade iron ore resources. Among all the reported technologies, biotechnologies in mineral processing – specifically bioleaching and microbially induced flotation – have emerged to be considered as low-cost, environmentally friendly potential alternatives to many of the current mineral processing techniques. This paper provides a comprehensive review of current research on the use of microorganisms for iron ore beneficiation and, further, discusses the applicability of bioleaching, bioflotation and bioflocculation for the beneficiation of low-grade iron ores.IntroductionIncreasing global demand for raw materials has led to diminishing resources of high-grade iron ore. As a result, the mining and utilization of low-grade hematite, limonite, specularite, siderite and goethite ores have attracted more and more attention. However, these types of iron ores are of complex paragenesis and fine disseminated grain size, and often contaminated by phosphorus in the form of solid solution. The distribution of phosphorus throughout the iron mineral crystals prevents the effective use of physical separation techniques, and these complex ores are at present largely untapped due to a lack of cost-effective and efficient processing methods. Chemical leaching and roasting-magnetic separation approaches have been mainly tested only on the laboratory scale and are all either cost prohibitive or ineffective when used on low-grade complex iron ores."

Jan 1, 2015

By A. Dell’Era, E. Ciro, C. Lupi

The indium recovery via electrowinning from sulfate baths has recently gained significant attention as it does not present toxic emissions, hermetically sealed system requirements, human health, and environmental hazards. Following previous works related to the optimization process for AISI 316L and Ni cathode, it was observed significant importance of the metal supports on the input and output parameters of the indium electrowinning process from sulfate solutions. Thus, comparing input and output parameters in both cases seems very interesting. Particularly, regarding the input parameters, the attention has been focused on the electrolyte composition, current density, and temperature, while productivity, morphology, and structure have been considered regarding the output parameters. Considering the productivity as the optimal output, the findings for Ni cathode were better than that for AISI 316L in most of the selected conditions studied. In the case of morphology, indium grains appear rounded and dendritic on the AISI 316L, while those on the Ni cathode show stratified lamellar grains. Anyway, the indium deposit obtained on Ni cathode shows bigger grains independently from the used operative conditions with respect to that on AISI 316L. Regarding the structure, it is clearly tetragonal, but preferential orientation, crystallinity, and deformation of the structure strongly depend on the metal support.

Jun 14, 2023

By S. J. Lefond

Most people, when Borates are mentioned, mentally visualize the famous twenty mule team (really eighteen mules and two horses), trudging across the Mojave Desert or "she burns green Rosie, we are rich." Actually, however, the first use of borax was prior to Babylonian times. Their emissaries had orders to bring borax Iron the Gobi desert for use as a flux by the Babylonian goldsmiths. The borate mineral imported for this is not known but probably was borax. The ancient Persians and Arabians knew about borax and the Arabic word "Baurach" appears in a two thousand year old manuscript. The Sanscrit word for borax was tincana which has been corrupted to tincal. The Chinese were using borax as a glaze in three-hundred B.C. Marco Polo brought the first borax, along with gunpowder and spaghetti, from Mongolia to Europe in the late 1300's. Borax from Tibet was imported to Europe for nearly 500 years. In 1772 boric acid (sassolite) was discovered around Tuscany, Italy as a precipitant from volcanic steam vents. Production of boric acid started there about 1815 and provided the sole competition to the borax from Tibet. Borate deposits in Turkey have been known and exploited on a small scale since the 13th century. It is only recently that the operations are being modernized and production increased. About 1836, borax minerals were found in Chile and Argentina with borax production starting in 1852 in Chile and in Argentina in 1886. During the latter half of the 19th Century, Chile was the principle world producer of borax.

Jan 1, 1980

By Alan Rhodes

This study is initiated to investigate the efficiency of separation of mineral slimes using electroflotation as compared to that of column and conventional flotation techniques. Important parameters such as collector concentration, pH, current density, aeration rate, etc., have been studied. The results indicate that electroflotation can be used more efficiently in processing rutile slimes (10 µ) under certain operating conditions.

Jan 1, 1982

By R. L. Bullock

For the past 30 years there has been a gradual evolution of mechanical excavating systems in underground hard rock mining applications. This paper traces many of the tests of various tools and methods to break hard rock, up to the present. The tools include impact hammers, boring machines, disc on boom mining machines, disc on revolving wheels and drums, picks and drag bits on revolving hubs, rock splitters, slot cutting systems, and with customized explosives/powder mini-blasting. While the progress has been slow, successes are being achieved in hard rock and more opportunities exist today than ever before.

Jan 1, 1995

By J. G. Groppo

A series of performance studies have been conducted using counter-current column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia and utilized a 0.15m (6 in.) I.D. column that was 5.79m (19 ft.) high. The refuse streams tested included both thickener feed and classifying cyclone overflow with a typical size distribution of 100 mesh X O. The percent solids of the column flotation feed varied from 1.5 to 15% while the ash content ranged from 30-60%. The concentrates produced contained 2-10% ash with BTU recoveries of nearly 90% using 0.12-1.25 kg/ton (0.25-2.5 lbs/ton) fuel oil and 0.12 kg/ton (0.25 lb/ton) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from 7 different seams are discussed as well as scale-up relationships utilized to design a full scale installation presently in operation.

Jan 1, 1990

By H. Askari-Nasab, B. Osei, K. Awuah-Offei

The U.S. coal mining industry consumes approximately 142 billion kWh/a of energy. The U.S. Department of Energy estimates that the industry’s annual energy consumption could be reduced by 49%. This constitutes nearly $3.7 billion of potential savings on coal production costs at 5.3¢/kWh of energy. Additionally, with climate change regulation on the horizon, any benefits from energy savings in the near future are compounded by associated reductions in CO2 emissions. Research indicates that operating conditions significantly affect energy efficiency. Modeling and simulation have been shown to be a cheap and reliable means of evaluating the effects of process interactions and operating conditions. The goal of this work was to apply stochastic process simulation to model the energy efficiency of a typical truck-and-shovel mining system and use the model to evaluate production strategies to improve energy efficiency. The research team conducted energy audits of truck-and-shovel overburden removal and used the results to develop regression models describing truck and shovel fuel consumption. The team then built a stochastic simulation model of the truck-and-shovel overburden removal operation and used it to assess a variety of improvement measures by simulation experimentation. Valid fuel consumption models for shovel loading and truck haulage have been formulated, based on the energy audit results. Valid stochastic process models of truck-and-shovel operations have been formulated to study energy efficiency. The following strategies, in decreasing order of impact, provide the most energy savings for truck-and-shovel overburden removal at the mine: (1) shorten haul roads, (2) increase shovel capacity and (3) increase shovel utilization through optimal truck matching. Additional data will be required to adequately describe operator effects on energy efficiency.

Jan 1, 2011