Search Documents

By Travis Q. Lyday

The Other South Pacific Island states extend from Palau, also called Belau, near the Philippines in the west, to French Polynesia in the east. However, a number of countries and territories have been omitted, from this chapter because their mineral production was insignificant to the local economy. These include the French over-seas territories of French Polynesia and Wallis and Futuna Islands; independent states, including Kiribati, Marshall Islands, Micronesia, Palau, Tonga, Tuvalu, and Vanuatu; the New Zealand freely associated state of the Cook Islands, and the New Zealand dependency of Niue. What mineral production existed in these islands was limited to construction materials such as coral reef limestone, crushed stone, and sand and gravel in minor quantities solely for domestic consumption. FIJI The mineral industry of Fiji continued to be dominated by gold, although this sector contributed less than 1 % to the gross domestic product (GDP) of the country. Gold and silver together ranked second in value among the country's exports. Fiji's economy contracted 11% during the 8-month period following the first, on May 14, of two military coups. Although the island nation had been a member of the British Commonwealth of Nations since its independence on October 10, 1970, Fiji's membership terminated with the emergence of the Republic or Fiji on October 15.

Jan 1, 1989

By Charles W. Huggins

The Bureau of Mines investigated palygorskite, a natural asbestiform material, to accumulate knowledge that might serve as a foundation for future synthesis of a similar material. Unit cell, chemical analysis, DTA, TGA, optical constants, and electron microscopy data were obtained. Selected palygorskite samples of bettor than 97-percent purity were used to obtain this information. Chemical analysis revealed the following formula: (OH2)4 (OH)2 Ca0.01Fe0.02K0 .c3Mg2.10A12.00Si7.93020.3.91 H2O. The optical constants for sodium light are a = 1.522; S = 1.530; ?=1.533; biaxially (-). The following orthorhomibic unit cell constants were determined: ao = 12.690 A, Z = 2, bo = 17.857 A, Dx = 2.327. co = 5.207 A, Identical diffraction patterns resulted from the three palygorskite samples that were studied. X-ray, chemical, DTA, TGA, and optical data were compared with literature values for similar fibrous materials. X-ray diffraction lines were indexed. Several electron micrographs were made to compare the structures of palygorskite and attapulgite with that of chrysotile. The micrographs revealed extremely short laths for attapulgite, very long flexible laths for palygorskite, and tubular structure for chrysotile.

Jan 1, 1962

By E. R. Cole

Bench-scale research at the Bureau of Mines has resulted in the successful development of a combination electrorefining-electrowinning method for recycling all the lead in scrap batteries. The method reduces energy consumption and eliminates toxic emissions, in contrast to present pyrometallurgical smelting, and the lead produced is pure enough for use in maintenance-free batteries. Anodes cast from molten lead scrap were electrorefined in 1-and 2-liter plastic cells using an electrolyte composition of 70 g/l Pb and 90 g/l free H2SiF6 (fluosilicic acid). Both reagent-grade and waste H2SiF6 were used. Cathode starting sheets were made from refined lead. Aloes, and later bone gelatin, and calcium lignin sulfonate addition agents were employed. The sludge remaining after separation of the lead metal was treated in a two-step leaching operation to solubilize the lead for recovery by electrowinning. Conditions for electrowinning were essentially the same as for electro-refining, except that insoluble Pb02-Ti (lead dioxide-coated titanium) anodes were used. The best results for both electrorefining and electrowinning were obtained with a current density of 170 amp/m2 and a cell temperature of 25° to 35° C. Cathode purity ranged from about 99.9 to 99.99+ pct Pb. Maximum energy consumption after 3 days, for electrorefining and electrowinning, was 90 and 700 kwhr per metric ton of refined lead, respectively.

Jan 1, 1981

By W. P. Yant

Publication of lists of the devices for giving respiratory protection which have been approved by the U. S. Bureau of Mines is made periodically for the purpose of aiding consumers in procuring equipment .374/ The last published list , approved to March 15 , 1935 , appeared as Information Circular 6845 with the same title as this article . The schedules of requirements and tests which the devices must meet in order to obtain approval are published 2/6/1/8/ by the Bureau of tests the devices must Mines and are available to the public . It is pertinent to mention that the preparation of a schedule of requirements for fresh-air supply devices of the types commonly known as positive -pressure respirators , airline respirators , sand- blast helmets , and hoods , has been practically completed and will soon be ready for release to the public .

Oct 1, 1936

By F. C. Gregory

"Introduction.The third annual mine-rescue maneuvers of the Globe-Miami District First Aid and Mine Rescue Association were held at Globe, Ariz., on November 5 and 6, 1923. The first demonstration was held in October 1922, and the results** from that experiment, both in the practical training and the interest aroused in the apparatus men, were so much more satisfactory than those from the ordinary smoke-chamber training, that Orr Woodburn, director of the Association, decided to hold similar maneuvers at frequent intervals. The second test was held on March 21-22, 1923, in connection with the meeting of the Southwest Mining Section of the National Safety Council at Globe.Place and Organization.The recent maneuvers were held in the same mine and conducted in the same general manner as the first, and the points of interest not brought out previously are described below. By studying the accompanying map the movement of the teams can be better understood.Thirty-three apparatus men were out on the first day and thirty-two on the second day, a total of forty-three men being trained.Mr. Woodburn was aided in directing the work by his two assistants from the mine-rescue station, two local safety engineers, and an engineer from the Bureau of Mines. Local mine superintendents and the State deputy mine inspector were interested spectators."

Jan 1, 1924

By Vern L. Kegler

This paper is one off a series dealing with mining methods and costs, sponsored and published by the United States bureau of Mines. ACKNOWLEDGMENTS The author acknowledges the, constructive and helpful suggestions and criticism of W. F. Lamoreaux, vice-president, and general manager of the Ducktown Chemical & Iron Co. United States Geological Survey Professional Paper- 139, by W. H. Emmons and F. B. Laney, has been drawn upon for some of the information contained in the paragraphs or history and geology.

Jan 1, 1931

By Robert L. Thorne

As an integral part of the investigation of critical and essential minerals in Alaska , the Bureau of Mines examined the lead deposits in the Slana area . Four examinations were made during June , July, and August 1945 in the 200 - square -mile area immediately northwest of Slana . The settlement of Slana lies near the conflux of the small Slana River with the mighty Copper River less than 60 miles southwest of Tek Junction on the Alaska Highway . Travel through the area and the examination of the properties were conducted by a three-man crew consisting of the author , a caterpillar operator , and a laborer . An RD6 caterpillar , equipped with blade and winch , was used in breaking trail and freighting through the country . Supplies and equipment were loaded on a 7- by 14 -foot , double - end , go -devil , which was hauled by the tractor .

Nov 1, 1946

By W. K. Sawyer

In this Bureau of Mines investigation, one-and two-dimensional gas reservoir simulators were combined in such a manner that pressure distributions both in an induced vertical fracture and in the surrounding formation, could be determined as a function of time for any specified well production rate. The technique used consisted basically of the alternate ust of one-and two-dimensional algorithms for obtaining new pressure distributions in the fracture and in the reservoir, respectively. The pressures at adjacent reservoir and fracture nodes were used to calculate flow rates from the formation into the fracture, which provided source terms for both algorithms. The combination model developed provides the only known means of simultaneously simulating transient gas flow in a vertical fracture and the surrounding formation. Thus, the technique developed would be useful in locating wells in a gas storage field in that the effects of both fracture length and conductivity could be considered prior to drilling and fracturing operations. In addition, it will be helpful in analyzing pressure drawdown tests in a vertically fractured gas well since the entire test can be readily simulated for a wide range of reservoir and fracture properties.

Jan 1, 1974

By B. S. Covino

The Bureau of Mines has conducted a laboratory and field corrosion test¬ing program to determine materials of construction for the leaching and gas-sparging crystallization environments of the clay-HC1 process in order to more fully utilize the alumina from domestically available kaolinitic clays. Laboratory tests were used to determine the corrosion rates of 22 metals and alloys by weight-loss measurements in these two environments of the process. The results of this laboratory study were used both to suggest metals and alloys for field testing and to determine the effect of the individual solution components on the corrosion behavior of the metals and alloys. Results from the field tests were used to recommend Ta, Ta-2.5W, and Ta-10W for con¬struction of the agitators for the leaching process. The metals and alloys recommended for construction of the gas-sparging crystallizer heat exchangers were Ta, Ta-2.5W, Ta-10W, Nb, Nb-1Zr, Nb-3Zr, Nb-28Ta-10W-1Zr, Nb-10Hf-1Ti, and Zr for the first stage and Ta, Ta-2.5W, Ta-10W, Nb-28Ta-10W-1Zr, Nb, Nb-10Hf-1Ti, and Zr for the second stage.

Jan 1, 1981

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Guatemala has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State.

Oct 1, 1929

By John Henderson

If you missed this year?s Texas State Holmes Safety Association meeting, you missed a great one. On January 23 & 24, 2009, we held the meeting that was rescheduled when Hurricane Ike threatened Corpus Christi in September 2008. Sixty-five persons from across the state attended the meeting held at the Holiday Inn Emerald Beach. The weather was 82 degrees, and the sky was clear and perfect for a safety meeting. Evaluations submitted by the attendees gave the presentations, the networking, and even the food top marks. There were eight councils represented; Big Country, Central Texas, Costal Bend, Heart of Texas, Hill Country, North Texas and North Central. Presentations included Workplace Examinations, Emergency Preparedness, Screen Safety, Contractor Responsibilities, Powered Haulage, Supervising for Safety, and Basic Inspections of Slings and Rigging. Mr. Edward Lopez, SC MSHA District Manager, gave the State of the District Address.

Jan 1, 2009

By A. J. Kraemer

The Bureau of Mines for a number of years has been carrying on an investigation of properties of crude petroleum from producing, fields in the United States and the Western Hemisphere, and has published a series of reports on these fields, including oil fields of Oklahoma2. Acknowledgements Thanks are due to R. R. Brandenthaler and Peter Grandone, of the Petroleum Experiment Station of the Bureau of Mines, at Bartlesville, Oklahoma, who reviewed the manuscript and contributed valuable suggestions. The samples were analyzed under the direction of E. C. Lane at the Bartlesville station of the Bureau of Mines.

Jan 1, 1927

By A. G. Starliper

Research was conducted by the Bureau of Mines to determine feasible roasting methods for the removal and the recovery of germanium, cadmium, and lead as enriched fractions from sphalerite concentrates. The two types of roasting processes studied were: (1) Batch, with a stationary bed, and (2) continuous, with a suspended bed, Results indicated that either method gave satisfactory metallurgical recoveries} but the continuous process is recommended because of inherent advantages. Final products were enriched fractions that could be treated by conventional methods for production of metallic germanium, cadmium, and lead. In the batch process, the concentrates were placed in a large tube furnace and heated at 1,080° C, an average of 3 hours. During the heating period, inert, reducing} or sulfur-laden gases were passed over the stationary charge to convey the sublimed metal sulfides from the hot portion of the tube to a lower temperature condensing zone at the end of the tube, where the metal sulfides were collected on baffles and recovered. In the batch and fluidizing roasting processes alike, the gases passed over or through the charge and served only as carriers for the sublimates and as suspension media in fluidization roasting. Since both processes depended on the volatilization, at relatively high vapor pressures, of the sulfides of germanium, cadmium, and lead, it was imperative that very little oxygen come in contact with the charge to alter the sulfide minerals. Germanium has a high affinity for oxygen, but in this instance it was buffered by being in solid solution in zinc sulfide.

Jan 1, 1961

Preventive maintenance practices are listed in the manufacturers' instruction books. In general, equipment that requires frequent and extensive preventive maintenance is generally the most costly. The manpower spent on these frequent trips to remote areas is such that it is usually better to invest in a more costly system which requires little preventive maintenance. The best preventive maintenance for the system is a good installation. 7.2 Preventive Maintenance and Inspections With any system, periodic inspection is required because of the corrosive atmosphere and adverse conditions that exist in underground mines. These inspections can spot potential trouble in the system. Repair or replacement at that time averts the possibility of losing effectiveness of all or part of the system. 7.2.1 Cables Approximately once per month all cables in the communications system should be inspected for kinking, chafing, cracking, wear, stretching, or other signs of physical abuse. Particular attention should be paid to cable glands at the entry or exit points to the various units in the system, where the cable goes around sharp corners, in the vicinity of holding cleats which may be clamping the cable too tightly causing potential damage, and across the areas where the cable is exposed to physical damage from outside sources, such as equipment or falling objects. If a cable is damaged, it should be replaced as soon as possible. It is mandatory that the ground leads and connections to carrier current phones be thoroughly inspected and maintained in good condition, since considerable hazard may exist to the operator or equipment if a ground connection is broken. 7.2.2 Pager Phones The most readily available test set to determine if a pager telephone is operating correctly is the pager phone itself. The following physical check of the system can be performed at any phone station. 7.2.2a Listen Circuit Remove the handset from its cradle and listen to determine if the circuit is functional, as indicated by the presence of noise or conversation on the line. If no noise or voice signals are present at the handset receiver, take the following corrective action: 1. Operate the handset press-to-talk switch several times. Any corrosion on the contacts of this switch may cause a receiver to be temporarily inoperative. Repeated operation may clear the condition. 2. Open the cabinet and see if the battery cables are properly connected and are making firm contact. Check the handset cable and its connections in the cabinet of the pager phone, and see if there is any evidence of a break in the cable, corroded contacts, or poor connections. 3. Remove the handset receiver earpiece by unscrewing it counterclockwise (to the left), and remove the receiver from the socket. Examine the handset cavity; in some units, a patch of cotton batting or floss is used as a barrier to reduce acoustic feedback in the handset. If the cotton patch has absorbed moisture, remove it and replace with a crumpled ball of soft rubber, stuffed just far enough into the handset so it will not touch the receiver or switch terminals. 7.2.2b Page Circuit and Talk Circuit Push the page switch, squeeze the handset press-to-talk switch, and call any other phone. Release the page switch

Jan 1, 1984

By Roy F. Abernethy

This report describes a method developed by the Bureau of Mines for the determination of beryllium in coal ash. Samples are put into solution by standard wet chemical procedures. Interfering elements are complexed with Na2EDTA, and the beryllium is separated by extraction of its acetyl acetone complex with chloroform or carbon tetrachloride. Final determination is made with Beryllon II.

Jan 1, 1970

By C. M. McCulloch

As part of the Bureau of Mines methane control program, the Pittsburgh coalbed was studied in Washington and Green Counties, Pa., and in Marion and Monongalia Counties, W. Va., where this coalbed is now being mined at its greatest depth. The coalbed thickness appeared to be structurally controlled; the bed was generally thinner near the axes of anticlines and thicker near the axes of synclines. The overburden isopach shows a similar relationship. Most of the clay veins in coal occur in the synclinal troughs, generally under sandstone roof. Cleat orientations measured in 18 underground mines showed that face cleats are perpendicular to the axial trends of the folds, and the butt cleats are parallel to the axial trends, indicating structural control of the cleat. Measurement and analysis of surface joint orientations provide a method for predicting the cleat orientations of the coalbed, but linears measured from infrared photographs and photoindex sheets helped only to determine regional trends. The results of these investigations provide a geologic framework for rational planning for underground mine development to use the best available technology to cope with methane emissions, coalbed discontinuities, and related ground support problems.

Jan 1, 1975

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION In previous reports 5 results were given of a manhole investigation carried out over a period from June 1929 to July 193C in cooperation with the Edison Electric Illuminating Co. of Boston. Mass., and during 1931 in cooperation with the Edison Electric Illuminating Co. of Boston and the Boston Consolidated Gas Co., to determine the general hazards of combustible gases and vapors in manholes and other underground openings owned by the Edison Electric Illuminating Co. and to develop methods of eliminating these hazards. These investigations have demonstrated that the detection, control, and elimination of combustible hazards in manholes can best be obtained by a close cooperation of the interested parties through a systematic and continuous inspection of manholes, under proper supervision.The investigation carried out during 1932 has been along lines similar to those conducted during 1929, 1930, and 1931 test crew consisting of two men, one an employee of the Consolidated Gas Co. and the other an employee of the Edison Electric Illuminating Co., was continuously employed during the year in the testing of gases in manholes served by the Edison system. The test crew was under the direct supervision of John Campbell, superintendent of the special service department of the Edison Electric Illuminating Co., and F. M. Goodwin, vice president of the Consolidated Gas Co.As in the previous investigations, all tests were numbered. The test-data sheets, on which the information regarding the tests was recorded, were prepared in triplicate, ono copy going to the Edison Co., one to the gas company, and the third to the Bureau of Mines at Pittsburgh, Pa. These test-data sheets were then filed (1) according to the town, (2) the street location, and (3) the manhole number; in this way a complete record of each manhole tested was immediately available. A typical test-data sheet was given in the 1931 report. These data sheets were found to entirely satisfactory and no changes were made during the 1932 investigation. The procedure of sampling manhole atmospheres, shipment of the samples to Pittsburgh, and method of analysis has been the same as that described in the 1931 report and need not be repeated here. Likewise, there has been no change in the method of calculation of explosibility of the samples analyzed or the use of charcoal filter tests given in appendix A."

Jun 1, 1933

By Oliver Bowles

"A Product from Mica Mines.Mica commonly occurs in pegmatites which consist of large crystals of feldspar and quartz, mica constituting but a small proportion of the total rockMuch of the feldspar thus thro n out during the process of mining is pure and of high quality, end the Bureau of Mines has suggested that much of it could be utilized for ceramic purposes. Encouragement is given to such utilization by the fact that several mines now worked for mica were formerly operated for the production of feldspar. ""'here mines are not readily accessible to railroads feldspar utilization might not be feasible, for it is a much lower priced product than mica and cannot therefore bear as heavy transportation expense. '""here mines ire located close to railroads, however, such utilization would tend to reduce the cost of mica mining, and at the same time assist in the solution of the waste disposal problem.The Bureau has recently been informed that some of the feldspar from mica mines near Spruce Pine, N.C., is now being sold and shipped away. An extension of this by-product industry is to be recommended.A Mica Deposit in New York City.The Bureau recently received a mica specimen obtained from a. building excavation at 157th St. and Riverside Drive, New York City. The specimen was about 2 by 4 inches in size, and fairly clear though containing numerous hair cracks. It was obtained only 7 or 8 feet below street level. At greater depth and with more careful methods of excavation material of much better quality might be obtained. The material submitted could be used for mica washers but not for sheet mica. It is stated by an official of a prominent mica company that many such fragments are obtainable in this locality and the possibility of the occurrence of a good mica vein is thereby suggested."

Jun 1, 1920

By J. S. Miller

The Bureau of Mines developed methods for fragmenting oil shale formations with chemical explosives to prepare oil shale for in situ retorting and to evaluate the extent of fragmentation by various methods. A combination of three methods of explosive fracturing was used: (1) The displacement and detonation of a liquid chemical explosive in a natural fracture system; (2) the use of 60-pct dynamite to relieve stress conditions of the rock around the wellbore; and (3) the use of pelletized TNT in a series of wellbore shots to fragment the oil shale. An attempt was made to seal or grout around the fragmented oil shale by drilling 67 holes and displacing approximately 200 bbl of neat cement in the fracture system to aid in evaluating the fragmented zone, Seven methods were used to evaluate the fragmented zone. The primary evaluation method was the recording of seismic waves to delineate the fragmented zone with results based on arrival time, amplitude, and record quality. The data from the seismic measurements indicated the extensively fragmented zone was approximately 95 ft in diameter and 70 ft thick. Results of the remaining methods of evaluating fractures--including air-flow tests, coring of the expected fragmented zone, elevation measurements to indicate overburden crowning, and surveys with high-speed camera, impression packer, and down-hole camera--agreed with and supported the data from seismic measurements. Further field application of explosive fracturing and evaluation methods is needed to determine when a zone of oil shale is effectively fragmented for efficient in situ retorting.

Jan 1, 1973

By Verne S. Mutton, William A. Slivensky, Eric S. Weiss, Kenneth L. Cashdollar, Deepak R. Kohli

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, cooperated with Tecrete Industries Pty. Ltd. and BHP Australia Coal in a research program to evaluate the strength characteristics and air leakage of four seal and two stopping designs for use in underground coal mines. A fundamental safety research area for NIOSH is to eliminate the occurrence of coal mine explosions or to mitigate their effects. One approach to achieve this goal is to develop new and innovative seal designs that provide increased explosion isolation protection for the mining personnel against ignitions that originate from within the gob or. other worked-out areas of the mine Full-scale seals and stoppings were constructed in the Experimental Mine at Lake Lynn Laboratory near Fairchance, Fayette County, PA. They were ail--leakage tested, then subjected to a series of explosions with average pressure pulses ranging from 25 to 500 kPa (3.5 to 72 psi). Instrumentation measured seal displacement and acceleration as a function of time, providing data to assist in the development of numerical models 1'01- future seal design. All three seals designed with Meshblock wire forlnwo~-k ant1 a lnonolithic shotcrete core withstood the first explosion test, which generated an avcr-age rnaximu~n pressure of - 140 kPa (-20 psi) while maintaining acceptable air leakage rates. These seals I-anged from 175 to 325 mm thick. They included a 2.7-m-high by 325-mm-thick seal that was tesled 27 hr after completion against this - 140-kPa explosion pressure, a special requirement of the test program. This seal survived explosions with pressure pulses up to 300 kPa (43 psi). The 2.3-m-high by 325-mm-thick Meshblock seal survived three explosion tests with overpressures up to 455 kPa (66 psi) and satisfied the air leakage criteria. A I ,200-mm-thick plug seal was constructed of two Gunmesh formwork walls in-filled with shotcrete and a 3,450-kPa (500-psi) strength Aquablend core. This plug seal survived three explosions with pressure pulses ranging 11-om 150 lo 430 kPa (-22 to 62.5 psi) with no measurable postexplosion air leakage. Two Gunmesh stoppings with thicknesses 01' 40 and 75 inln withstood explosion overpressures of 23 and 115 kPa, respectively. Anchoring all seal and stopping designs into the roof, ribs, and floor with steel "rootbolts" provided very effective boundary constraint that is critical to the performanceofstructures subject to explosion overpressures.

Jan 8, 1999