Search Documents

By Kevin M. Connor, O&apos

This report documents-the process of literature review, site selection, instrument installation, data acquisition, and preliminary data reduction performed to evaluate the influence of rock mass discontinuities on coal mine subsidence. A system of surface, subsurface and mine level instrumentation was installed at the Armco No. 7 Mine in Montcoal, West Virginia where the overburden varied in thickness from 630 to 1040 feet. Survey monuments, borehole pressure cells, full profile borehole inclinometer-extensometers, mine level extensometers, stressmeters and tape extensometer convergence stations were installed to monitor displacements and stress changes. Final design of the instrumentation system was based on: a) review of available information, b) field mapping and analysis of areal photography, c) drilling, and d) borehole geophysics. The report contains the complete graphed data of stress and displacements accompanying the longwall mining of a 4800 ft long by 480 ft wide coal panel.

Jan 1, 1983

By Robert W. Waytulonis

The Federal Bureau of Mines contacted 29 organizations--mine maintenance departments and equipment manufacturers--concerning service experience and construction of diesel exhaust-gas water scrubbers. Scrubbers are used primarily on mobile diesel-powered mining equipment subject to 30 CFR 36. Because the scrubbers cool exhaust gas and act as flame arresters, their failure would compromise safety in underground mines. Scrubber maintenance problems and frequency and modes of failure were identified, and construction materials and techniques were evaluated. Three failed scrubbers were randomly selected from two cooperating mines, and their modes of failure were determined. In conjunction with failure analyses, mine water and scrubber water solution samples were chemically analyzed to characterize corrosive properties. Sludge and mineral deposits and different types of corrosion and metal fatigue were identified as problems leading to scrubber failure. The corrosion process is explained; maintenance practices, construction materials, and manufacturing methods that could be used to reduce premature failures and allow longer effective scrubber life are identified; and basic changes in scrubber design are suggested. If type 304 stainless steel is used throughout the scrubber and regular maintenance is performed, long, dependable service can be expected. Other materials such as 304L, 316, or other more exotic steel alloys may be necessary under certain conditions.

Jan 1, 1982

By J. W. Jensen

This report was prepared as a background reference for future publica¬tions concerning the damping capacity of metals and alloys. It contains a broad description of the theory and methods of measuring damping capacity and correlates the developments of the past decade in terminology, units, and techniques. Damping-capacity instrumentation at the Mississippi Valley Experiment Station, Rolla, Mo., is described. The bibliography contains over 150 references to recent articles, each tabulated as to material investigated and test variables, such as frequency, stress, mode of vibration, and temperature. INTRODUCTION After it discovered high-damping manganese-copper alloys before World War II, the Bureau of Mines began research on the damping capacity of alloys and has continued to expand this activity to the present time. In physical metallurgy, damping capacity has become an important research tool in the Bureau. The physical measurement of the damping properties of alloys was begun at the College Park laboratories, and later conducted at Salt Lake City under the direction of Dr. E. V. Potter. Among the many articles resulting from this work, Damping Capacity of Metals (108)3/ has received frequent men¬tion in more recent literature and describes briefly the methods of measurement employed at that time.

Jan 1, 1959

In Bureau of Mines research on recycling chrome refractory wastes, used refractories from argon-oxygen decarburization and electric steelmaking furnaces were beneficiated, concentrates were reformed into briquets, and modulus of rupture tests were conducted at 1,350° C. The test results indicated that the beneficiated minus 6-mesh material could be used for producing magnesia-chrome refractories.

Jan 1, 1980

By Richard A. Dick

Underground blasting in permanently frozen gravel was studied in a 7-by 12-ft drift by running a nonreplicated 2 X 2 X 2 factorial experiment on the effects of type of cut, delay, and explosive on the fragmentation subsystem. Comparisons were made between a V-cut round and a burn-cut round, millisecond delays and half-second delays, and 40 percent special gelatin and 60 percent high-density ammonia dynamite. The number of large blocks in the muck pile) loading time, shuttle car operating time lost because of cleanup needs, length of advance per round, and length of muck pile were recorded and statistically analyzed. None of the blast parameters had a significant effect on the length of advance or length of muck pile, although the half-second delays tended to give a shorter muck pile than millisecond delays. The burn cut required less secondary breakage, less loading and cleanup time, and gave better overall fragmentation than the V-cut. The ammonia dynamite shots required less secondary breakage and less loading time than those using special gelatin. The half-second delays gave better overall fragmentation and required less cleanup time, but the millisecond delays gave a better loading rate. None of the differences between delays and explosives were notably significant.

Jan 1, 1970

By R. M. Santmyers

The pigments, whose colors are due primarily to iron exides and iron hydroxides, comprise a variety of yellow, brown, red, and sometimes black paint-coloring agents, both natural and artificially prepared. The natural pigments in this group include ocher, umber, sienna, mineral paints, paint rock, and mortar colors. When the natural color or tinting power--either in the raw state or after treatment--is too weak, these pigments may be "forti- fied" or strengthened. Ocher, umber, and sienna, rhile often described as "iron oxide pigments," are also known as "earthy" rigments. Inasmuch as the iron content of these pigments is, in general, somewhat lower than that of other iron oxide pigments, the ochers, umbers, siennes, and other brown earth pigments are not discussed in the present paper. In addition to a discussion of natural or artificial pigments whose color is due to the presence of iron oxide in some form, this paper contains data on mortar colors, which are medium or low grade pigments used for tinting mortar, cement, and concrete. A great variety of materials are used for theso purposes, including "blue billy" (residue left from roast- ing pyrite), ground slate and shale, and even culm from coal washeries. Dur- ing the past three years, there has been a definite trend among the producers of iron oxide pigments to push the sales of the better grades of colors for tinting mortars. Due to the amount of low-grade coloring matter that is re- quired to impart a strong color to concrete (in soro cases as high as 15 per cent of pigment is necessary) the strength of the cement may be materially impaired. The addition of some 2 per cent of the higher grades of iron oxide to the concrete mix imparts a brighter and stronger colcr, does not weaken the material, and in the end is not as expensive as the low-grade pigments formerly used. Iron oxide pigments occur in nature in various shades and colors, but the red pigments are the most important and account for the larger part of the total red pigments used.3/ The nomenclature of these red pigments is involved and the names given to them are descriptive of the shade rather than of origin, method of produc- tion or chemical composition. In most cases the red pigments under this class may occur naturally or may be produced by heating hydrous iron oxide pigments such as yellow ocher to a sufficiently high temperature to drive off the water of composition. They may also be prepared by fortifying naturally-occurring pigments with stronger natural or synthetic oxides or with coal-tar dyes (e.g. alizarine lake), Most of the mineral reds derive their color from the presence of ferric oxide (Fe2O3), the mineral hematite. This may be present in relatively small percentages, as in the red slates and shales, or it may constitute as much as 90 per cent or more of the material, as in Spanish red. The principal iron oxide pigments used in the manufacture of paint are discussed in the following pages.

May 1, 1932

By Albert L. Toenges

The purpose of this paper is to describe some of the methods and practices of mining coal mechanically where more than one shift is worked, with the view of determining the advantages and disadvantages of various types of equipment and mining systems now in use. This paper is in the nature of a progress report, and, as the number of mines discussed in it is limited, the conclusions drawn in the comparison of various systems are not final but may be revised after subsequent investigations. Physical conditions vary in different and in the same mining districts and determine, more

Jan 1, 1938

By M. John Brodie

This report reviews the regulatory environment as it pertains to waste rock management and disposal from mining operations, excluding coal and placer gold operations, in the \irate of Alaska. It is based on the EPA's staff position on an effective program to regulate mining waste as presented in the May, 1990 Strawman II document. The unique conditions which occur in pans of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a waste rock facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection, are examined.

Jan 1, 1992

By Allan E. Martin

As part of a comprehensive investigation of tie mechanism of desufurization of iron and steel by slags, the Blast Furnace Studies Section, Metallurgical Division, Bureau of Mines, in cooperation with the Institute of Technology-, University of Minnesota, has made a study of the forms in which sulfur occurs in blast-furnace slag. This report presents data on the three sulfides most important in iron smelting, namely, ferrous sulfide, manganous sulfide, and calcium sulfide. The tendency of these sulfides to form colloids in the molten slag was determined by an examination of quenched samples with an ultramicroscope. Vogt5/ conducted experiments on sulfide silicate melts and examined synthetic blast-furnace slags in a partly crystallized condition. His conclusions were that FeS, CaS, and bins, or isomorphous compounds, such as (FexCay)S and (MnxCy)S, were precipitated Prom the melt, depending on the composition of the slag. In all specimens sulfides were visible and were spherical.

Jan 1, 1941

By David E. Siskind

The Bureau of Mines studied airblast from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Research results obtained from direct measurements of airblast-produced structure responses, damage, and analysis of instrument characteristics were combined with studies of sonic booms and human response to transient overpressures. Safe levels of airblast were found to be 134 dBL (0.1 Hz), 133 dBL (2 Hz), 129 dBL (6 Hz), and 105 dB C-slow. These four air-blast levels and measurement methods are equivalent in terms of structure response, and anyone could be used as a safe-level criterion. Of the four methods, only the 0.1-Hz high-pass linear method accurately measures the total airblast energy present; however, the other three were found to adequately quantify the structure response and also represent techniques that are readily available to industry. Where a single airblast measuring system must he used, the 2-Hz linear peak response is the best overall compromise. The human response and annoyance problem from airblast is probably caused primarily by wall rattling and the resulting secondary noises. Although these will not entirely be precluded by the recommended levels, they are low enough to preclude damage to residential structures and any possible human injury over the long term.

Jan 1, 1980

By R. V. Ramani

Procedures have been developed which permit determining in either existing or new mines the optimum diesel equipment deployment schemes and the effect of. diesel exhaust on mine-air quality. Specifically, the following areas are covered in the report: 1. Description of diesel deployment schemes in four underground coal mines that were visited is provided. 2. Description of the analysis procedure to determine the number of shuttle cars required to maintain maximum theoretical continuous miner (or loader) production rates in typical room-and-pillar mining systems and of exhaust contamination resulting from the deployment of diesel powered shuttle cars are provided. Sensitivity analyses to determine the effect of changes in input variables on production and contaminant concentrations are also discussed. 3. Description of the analysis procedure to develop the locomotive operating parameters is provided. Assessment of both production performance as well as estimates of the magnitude of diesel exhaust contamination of the mine air are also made. 4. Recommendations for extensions of this research are outlined and include developing and testing procedures for 1) determining equipment duty cycles for the diesel equipment, and 2) studying the exhuast contamination of mine air on the basis of these duty cycles.

Jan 1, 1978

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crashed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summarizes of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling a t the same group of quarries. OBJECT OF STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By Franklin D. Cooper

The value of nonfuel raw mineral production in the United States for 1977 increased over that of 1976 by 5%, from $16.7 billion to $17.5 billion. Metals declined by 5% from $6.1 billion to $5.8 billion, chiefly because of strikes in the iron ore industry and a depressed copper market. Subsidization of mining industries in some foreign countries accounted in part for the excess of copper and some other metals on world markets. Weak metal markets and continued slowdowns in the world economy were the main reasons of the virtual absence of new mine projects. Increasing domestic governmental involvement affecting mineral industry activities, such as pricing controls, public land withdrawals, and the Surface Mining Control and Reclamation Act, effective August 3, continued to be controversial and to be criticized by various segments of the industry.

Jan 1, 1980

By Chas. F. Jackson

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By F. D. DeVaney

Metallurgists and coal-washing engineers have used heavy liquids for years in studying the characteristics of ores and coal. By such means true separations can be made between the various specific-gravity increments in the materials examined. To use of heavy liquids has permitted determination of the possible grades of tailings and concentrates by specific-gravity methods on any particular size, and therefore the size to which the ore must be crushed to free the valuable material. The simplicity of float-and-sink separation and the high degree of efficiency attained in the laboratory are factors that commend the method for commercial concentrations.

Jan 1, 1940

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By Jesse J. Brown

Over 60 simple; were prepared and forwarded to Dr, S. Z. Toma, TPO, PMSRC as a result of this project. Included among these samples were various low temperature forms of silica. Samples of quartz, cristobalite, and tridymite with iron, manganese, and titanium impurities present were prepared. In addition, a long series of samples both wet ground and dry ground for times from 1/2 to 8 hours were prepared. Numerous miscellaneous samples were submitted which included kaolinite, calcite, muscovite, illite, montmorillonite, Ba3(P04)2, and YPO4 among others, in response to special requests from the TPO. The silica rich portion of selected binary (CA 203-Si02, In 203-Si02, Li20-Si02) Na20-Si02, PbO-Si02, SnO2-Si02, Sn02-Si02 BaGa204-SiO2 and SrGa204-Si02) and ternary systems (Na20-Ga203-Si02 and Li20-Ga203-Si02) was investigated to determine the effects of solid solubility on the stabilization of the high temperature forms of tridymite. In addition to the determination of the extent of these crystalline solubilities, observations were made. on the mechanism of the transformation of silicic acid to tridymite and the rate of the reaction in the presence of foreign ions,

Jan 1, 1973

By W. C. Babcock

This report covers Phase V of .a continuing program to apply a new liquid membrane process called coupled transport to the recovery pf metals from hydrometallurgical leach solutions. During this phase of the program, a membrane system of moderate scale was constructed and field-tested at the Exxon Highlands Mine and Mill Co. site near Douglas, Wyoming. The test unit contained four hollow-fiber membrane modules, each with 100 ft2 of membrane area. In the field tests, about 1000 gallons per day of leach solution was processed. The unit was operated on the leach solution for about 50 days. Leach solution entering the unit contained 100 ppm uranium. This concentration was reduced to about 5 ppm by coupled-transport treatment, and the uranium was concentrated to about 2 wt% as a uranyl carbonate product. Under these conditions, a transmembrane uranium flux of about 2.5 lb/ft2-year was obtained. An economic analysis showed that the cost of recovering uranium from this leach solution via coupled trans-port is about $1.20/lb. At higher concentrations of uranium in the leach solution this cost is reduced. For example, at 1000 ppm the cost of uranium recovery is about $0.30/lb.

Jan 1, 1983

By F. D. DeVaney

Metallurgists and coal-washing engineers have used heavy liquids for years in studying the characteristics of ores and coal. By such means true separations can be made between the various specific-gravity increments in the materials examined. To use of heavy liquids has permitted determination of the possible grades of tailings and concentrates by specific-gravity methods on any particular size, and therefore the size to which the ore must be crushed to free the valuable material. The simplicity of float-and-sink separation and the high degree of efficiency attained in the laboratory are factors that commend the method for commercial concentrations.

Jan 1, 1940

By C. S. Tout

While investigating methods for determining the best temperatures for hot-working experimental stainless steels, the Bureau of Mines Albany Metallurgy Research Center developed a machine in which hot-twist tests could be made in a few minutes. This machine is similar to some used previously except that specimens are heated by induction instead of by radiation, and their temperature is measured by a calibrated radiation-detection unit instead of by a thermocouple. In. developing the technique for using the new machine, tests were made on specimens of medium-carbon steel, mild steel, and AISI (American Iron and Steel Institute) type 304 stainless steel. Tests also were made on as-cast specimens and preworked specimens of experimental AISI type 202, low austenitic stainless steel, and as-cast specimens of AISI type 301 experimental stainless steel. The optimum hot-working temperatures were determined for all types of steel tested. Also, data were gathered on the effects of test speed and temperature on torsional strength and the effect of twisting on tensile stress in the specimen.

Jan 1, 1962