Search Documents

By Abdurrahman Cetinbas

The periphery of longwall panels in the Pocahontas No.3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray system.

Jan 1, 1974

By W. F. Watts

This report describes the Mine Inspection Data Analysis System (MIDAS) developed by the Bureau of Mines to analyze the records of industrial hygiene samples collected by the Mine Safety and Health Administration (MSHA) in metal and nonmetal mines. MIDAS is the first system capable of sorting, editing, analyzing, and reporting these data. It is also the first system designed to be used by a number of Government agencies. At present the system contains 225,000 personal and area samples for 61 contaminants in 45 industries. The records date from 1974 to early 1980, and MSHA plans to provide yearly updates to the system. This report presents preliminary analyses of dust exposures and discusses the potential uses and limitations of these data. Analysis of the dust data for 1978 and 1979 showed that bagging had the highest percentage of dust overexposure. Morn than 40 pct of the 1,536 respirable quartz dust, total nuisance dust, and total silica dust samples exceeded the MSHA exposure limit. Other dusty occupations are ranked according to their percentage of overexposure.

Jan 1, 1981

By Michael A. Staiano

The objective of this study was to determine the magnitude and sources of environmental noise from mining operations near populated areas, to de-scribe monitoring techniques, and to identify applicable existing noise abatement techniques. To this end, noise surveys of a representative sample of mines and quarries were conducted. Noise levels at site boundaries and near specific equipment and ensembles of equipment were measured. Noise exposures in terms of annual day-night sound level were calculated for the boundary noise measurement locations. In addition, the relative sound level contributions were estimated for the mining equipment noise sources affecting the boundary locations. Noise abatement methods falling into three categories were analyzed: equipment practices, operational/administrative practices, and equipment quieting. Selected applications of noise abatement methods were evaluated in hypothetical situations with emphasis upon machinery selection and use. Procedures for measuring noise around mining operations were provided.

Jan 1, 1981

By Thomas E. Finch

This report is a continuation and expansion of a previous USBM grant (No. G0254004) which examined alternative methods of handling the parting between two coal seams in a surface mining operation. The alternative methods consist of equipment implementation in either a stowing or haulback technique. Following a typical strip mine conformation, the parting is directly stowed or hauled back and placed in the pit bottom after second seam removal. The objectives are to produce an environmentally sound material placement technique and to increase prime stripping machine utilization. This report contains the engineering philosophy behind two computer programs created to evaluate parting handling methods over d wide range of coal and parting thickness ratios. The nature of the computer approach allows cost sensitivity analysis and quick updating of costs. The two programs are clearly presented with documentation and examples such that consumers may apply then to their own operations.

Jan 1, 1977

By Andrew B. Cecala

The Bureau of Mines conducted a brief laboratory study on the 10-mm diam Dorr-Oliver nylon cyclone to investigate (1) whether high wind speed (>300 ft/min), or sampler inlet orientation with respect to wind direction, can introduce errors when sampling respirable dust, and (2) whether any such errors can be reduced by using an inlet shield. Being preliminary in nature, the study was not structured to produce definitive results, but rather to discern likely trends and to indicate whether or not a more in-depth study of the problem is warranted. Photometric mass sensing measurements suggested that as the wind velocity increased, the cyclone sampling directly into the high-velocity airstream tended to oversample, relative to the cyclone sampling in a low-velocity airstream. Orientation of the sampler introduced measurable differences in sampling efficiency at higher wind velocities. A shield placed around the cyclone diminished the effects of wind velocity and sampler orientation on sampler performance. Results of this work offer sufficient evidence to substantiate the need for a more in-depth study.

Jan 1, 1983

By Verne E. Hooker

This Bureau of Mines report summarizes the results of modifications in the borehole deformation gage design and subsequent changes in the overcoring techniques. Modifications in the borehole deformation gage have greatly improved the creep characteristics and enhanced the versatility of the gage. In situ field tests in competent rock near St. Cloud, Minn., provided sufficient data to compare the reliability between gages and new techniques in obtaining good engineering estimates of stresses. Near-surface horizontal stresses at the test sites are compressive and biaxial in nature.

Jan 1, 1974

By Eugene L. Grumer

High-expansion foam was applied to the flames of six fuels burning in a 1-foot-diameter tray. The flames of three hydrocarbon fuels were more readily extinguished than the flames of methanol, acetone, or unsymmetrical dimethyl hydrazine. The result is rationalized on the basis that heat transfer from flame to fuel surface is primarily radiative with the hydrocarbons and more largely convective with the nonhydrocarbons. INTRODUCTION Equipment for producing high-expansion foams has been developed by the Bureau of Mines to control coal mine fires.5 Recently such equipment has been redesigned for portability and has now been produced commercially for other fire-fighting applications. In May 1961, a 50-by 50-foot gasoline fire was extinguished within 2 minutes by a trailer-mounted foam unit that produced 12,000 cu.ft./min. of high-expansion (1,000:1) foam.6

Jan 1, 1962

By J. J. S. Sebastian

The process development described in this report was carried out at the Morgantown Station of the U. S. Bureau of Mines in cooperation with West Virginia University. An experimental laboratory-scale pilot unit to gasify coal dust in entrainment was constructed on the Campus of the University in Morgantown. The enormously accelerated demand for liquid and gaseous fuels and utilization of our immense coal resources require that a low-cost process be developed for the gasification of a wide variety of coals. Such a process would be a major factor in lowering the cost of synthetic liquid fuels. None of the proc3sses developed in Germany prior to and during World War II, such as the Winkler process, the H. Koppers dust gasification process, the Wintershall-Schmalfoldt process, etc., meet all the requirements for a low-cost process under American conditions. Nor has any other process designed and experimentally operated at atmospheric pressure during the post-war period in this country appeared to fulfill all of the necessary conditions for a low-cost process.

Jan 1, 1950

By David L. Bickel

The following instructions and descriptions are presented in two parts to assist an individual to make the borehole deformation gage transducer, and to assemble and test the three-component borehole deformation gage. This Bureau 8 of Mines three-component borehole deformation gage (4, 8, 11)2 fits in a 1-1/2-in-diameter borehole that is drilled in rock and then overcored to determine rock stress.

Jan 1, 1978

By E. D. Palmes

Phase I of these studies demonstrated the feasibility of measuring the efficiency and capacity of sorbents in tube-type samplers for contaminant gases. This was accomplished by measuring concentration at various points along the length of the diffusion path during sampling. Concentrations were measured by removing small aliquots with gas-tight syringes and gas chromatography. With hexane as the gas and activated charcoal as the sorbent the procedure was quite successful and we proceeded with Phase II of the study; this involved application of the principle to gases of importance in diesel exhaust using a variety of sorbents. When we worked with high concentrations of the test gas we clearly demonstrated the differences in both efficiency and capacity of the sorbents for each of several gases. The chief drawbacks of the system were that we were unsuccessful in determining more toxic gases at realistic occupational exposure levels or determining formaldehyde at any level using the flame ionization detector. It was concluded that, although the method is feasible, more sensitive methods of measuring concentrations of gas in the tube must be developed to make the procedure applicable to regions of chief industrial hygiene interest.

Jan 1, 1983

By Ronald T. Mayerle

A mineral survey of portions of two contiguous WSAs (Wilderness Study Areas) along the South Fork Owyhee River in southwestern Idaho and north-central Nevada was done by the U.S. Bureau of dines in 1984. The portions of the WSAs, known as study areas, have a combined area of 47,610 acres. The Idaho study area consists of 42,430 acres of the 42,510-acre South Fork Owyhee River WSA (ID-16-53). The Nevada study area consists of 5,180 acres of the 7,840-acre South Fork Owyhee River WSA (NV-010-103A). The Idaho study area is within the Boise District of the Bureau of Land Management, and the Nevada study area is within the Elko District. In the Nevada study area, no claims or hard rock mineral occurrences are known.

Jan 1, 1986

Provide optimum visibility of mining operations while maintaining protection and comfort for ma-chine operators. Approach Cabs and canopies with hydraulically powered variable-height control were developed for several machines and tested in underground mining operations. How It Works From his position in the cab, the operator can raise or lower the cab, selecting a height that offers either more visibility of the working place or greater clearance for tramming. The entire cab enclosure moves up and down on guide rollers that ride on a pair of rails, and is actuated by a hydraulic cylinder controlled from within the cab. Normal working heights, for each of the four different cabs developed, are with the cab bottom from 6 to 8 inches above the mine bottom. A typical range of elevation (excursion) afforded by this design is shown in Figure 1.

Jan 1, 1978

By R. F. Chaiken

The Bureau of Mines has carried out experimental and theoretical studies with prilled and pulverized ammonium nitrate-fuel oil (AN-FO) mixtures containing varying amounts of fuel oil in an attempt to quantify the effects of stoichiometric composition, nonideal detonation behavior, and expansion volume on the production of CO, NO, and N02 fumes. Experimental fume measurements were obtained in the Bureau's large closed gallery facility (7.2 X 104 liter expansion chamber) and in the standard Crawshaw-Jones apparatus (90--liter expansion shamber) using a prepackaged charge configuration containing about 450 g of explosive.4 The theoretical calculation of toxic fumes was achieved with an equilibrium detonation code called "TIGER,," Contrary to initial expectations, the NOx (= NO + N02) fumes from the large gallery test were found to be in essential agreement with the Crawshaw-Jones results. It was also concluded that (1) "TIGER" calculations offer a good approach to the prediction of toxic fumes; (2) there is a basic problem in extrapolating laboratory measurements of CO fumes to mine conditions--this being due to postdetonation oxidation of CO to CO2; and (3) the detonation velocity decay rate of an explosive is a useful experimental parameter for correlating toxic fumes production with nonideal detonation behavior.

Jan 1, 1974

By S. L. Crouch

An important class of mining problems involves excavations in planar seam or vein-type deposits. In many instances it can be assumed that the seam is at 'infinite' depth in a homogeneous, isotropic or transversely isotropic, linearly elastic rock mss, and that the normal to the plane of the seam is a principal stress direction. Rational planning of excavations in such deposits requires a knowledge; of the stresses and displacements induced by complicated, irregular excavation geometries in the plane of the seam. This problem previously has been solved either numerically or by means of an electrical resistance network analog. Both of these methods effectively simulate the mined portions of the seam as a dislocation in an otherwise continuous mass, and determine the complete solution in terms of the stresses and displacements at the seam. In both cases, the plane of the seam is divided into a number - say, M x N - of squares, and the solution to the problem is determined in terms of the solution to an M x N system of equations. The numerical approach requires that these equations be solved explicitly, while the analog; solves them instantaneously with current analogous to stress and voltage to displacement. A purely numerical solution of practical problems can require a substantial amount of computer time, particularly in situations that demand some sort of sequential analysis, either due to successive mining or to nonlinear behavior of the seam material. This report describes a combined analog-digital computer system for solving problems that are impractical when either device is used separately. The digital computer and the analog are interfaced so that the digital computer can receive information from the analog via a switching matrix and an analog to digital converter, and can activate points of the analog via another switching matrix and a set of digital to analog converters. The resulting hybrid system can be used to simulate arbitrary "stress-strain" characteristics for any portion of the seam by an iterative procedure similar to the initial strain method used in nonlinear finite element analysis. Thus, the hybrid system combines the speed of analog computation with the decision-making capability of the digital computer: the analog instantaneously solves the set of equations, and the digital computer decides how the initial strains must be altered for the solution to be compatible with the prescribed "stress-strain" characteristics for the seam material. The hybrid computer system has many implications for rational planning of underground excavations, since it allows practically any type of inelastic seam behavior or artificial support characteristics to be simulated. Inelastic seam behavior, for example, might be due to either rock failure or to time-dependent deformation.

Jan 1, 1974

By Terry McMahon

This Bureau of Mines report describes the rock burst problem and measures being taken for its alleviation in the deep underground mines of the Coeur d?Alene Mining District in northern Idaho. The geologic features that contribute to rock bursting in that area are discussed and briefly compared with similar features in other burst-prone mining districts throughout the world. Early investigations to understand and control rock bursting are reviewed, and the mechanics of bursting are discussed in terms of the seismic events that produce them. Sources of strain energy, rock failure mechanisms, and the conditions necessary for the release of seismic energy are covered in detail. Rock burst research in the Coeur d'Alene District is described. Included are discussions of the microseismic method as both a research tool and as a rock burst monitoring system, rock destress blasting and preconditioning methods for rock burst control, and stoping methods currently being developed to reduce rock burst hazards.

Jan 1, 1988

By Leonard Obert

This report presents evidence indicating that when rock is stress-relieved during the course of mining or in drilling a core, it may be altered or damaged to the extent that the physical properties of the relieved specimen are not the same as those of the in situ rock. Furthermore, this type of damage may result from stress change other than that accompanying stress relief, such as the application of a relatively large compressive stress. In some instances the damage is microscopic, manifesting itself as incipient cracks or the failure of individual crystal bonds. However, if the sample is taken from a high-stress area, macroscopic damage may occur.

Jan 1, 1962

By George J. Conroy

To provide data as a basis for proposed acceptance standards and procedures covering permanent splices in trailing cables, the Bureau of Mines conducted testing programs on the flexure life in flat types W and G dc trailing cable splices and ground conductors. Primary reliance was placed on laboratory testing, although some cross comparisons were made at manufacturers' plants and mine operations Besides providing data for acceptance standards and procedures, results of the program should promote the general improvement of commercially available splice kits.

Jan 1, 1977

To be able to continuously monitor the noise to which underground workers are exposed as a better way to help prevent hearing damage. The Approach: The Bureau of Mines has developed a Time-Resolved Audio Dosimeter which can be worn by miners to record noise level every 30 seconds and store It in a miniature solid state memory. Figure 1 is a photo of the dosimeter. [ ] How It Works: Acoustical noise is picked up by a micro-phone and fed to a sound level meter which produces a d-c voltage proportional to the A-weighted sound pressure level. (As specified by federal regulations, the A-weighted sound pres-sure level approximates the response of the ear by discounting the higher and lower frequency components of the noise.) This d-c voltage controls an oscillator which, together with related circuitry, produces a pulse train having a frequency that's proportional to the noise level.

Jan 1, 1975

The 1969 Lignite Symposium was held at Grand Forks, N. Dak., on May 1-2, 1969. Cosponsored by the University of North Dakota and the Department of the Interior, Bureau of Mines, the meeting was the fifth in this series. Registrants from many States and Canadian Provinces attended the meeting representing many segments of energy-oriented companies, State and Federal Government, and universities. At 2-year intervals, these symposia provide a common meeting place where recent research and developments in technology and utilization of energy resources with emphasis on solid fuels (lignite) are presented. Proceedings3 of the previous symposia including a Forum held in 1958 have been published.4

Jan 1, 1970

By C. T. Baroch

CESIUM-137 ISOTOPE began to displace cobalt-60 III the treatment of cancer during 1956. Production and Consumption.-Consumption of cesium and rubidium was approximately the same as in 1955. Production, however, decreased, as several companies shipped from stocks produced in previous years. South Africa was the source of most cesium and rubidium minerals used in the United States in 1956. Cesium and rubidium metals and compounds were produced from ore by: DeRewal International Rare Metals Co., Philadelphia, Pa.; Fairmont Chemical Co., Inc., Newark, N. J.; Foote Mineral Co., Philadelphia, Pa.; and Rocky Mountain Research, Inc., Denver, Colo. Most sales were to domestic consumers, but small quantities were exported to Australia, England, Germany, and Sweden. New production facilities were under construction in. 1956 by San Antonio Chemicals to produce mixed potassium, rubidium, and cesium carbonates. A plant capable of separating and packaging 200,000 curies of cesium-137 annually was under construction at Oak Ridge National Laboratory.6

Jan 1, 1958