Search Documents

By Tetsuo Yamazaki

Manganese nodules on deep ocean floors have continuously received attention as potential sources for strategic metals such as Co, Ni, Cu, and Mn, due to their vast distribution and relatively higher metal concentrations (Mero, 1965; Cronan, 1980). Several registered Pioneer Investors have already identified promising sites in deep-sea regions for manganese nodule mining (ISA, 1998), and appropriate mining technologies have been developed during the last thirty years by the international consortium and several nations (Welling, 1981; Kaufman et al., 1985; Bath, 1989; Charles et al., 1990; Yang and Wang, 1997; Yamada and Yamazaki, 1998; Hong and Kim, 1999; Muthunayagam and Das, 1999). The mining feasibility for manganese nodules, including an economic evaluation, has been examined in detail by some researchers (Andrews et al., 1983; Hillman and Gosling, 1985; Charles et al., 1990; Soreide et al., 2001).

Jan 1, 2011

By Rolf B. Pedersen, Filipa Marques

The extension of the Mid-Atlantic Ridge north of Iceland has collectively been referred to as the Arctic Mid-Ocean Ridges (AMOR). The AMOR extends from the northern shelf of Iceland, to the Siberian shelf in the Laptev Sea, passing en route through the Norwegian- Greenland Sea, the narrow gateway of the Fram Strait, and across the Eurasia Basin. The AMOR is 4000 km long and is divided into six super segments: 1) the Kolbeinsey Ridge, 2) the Mohns Ridge, 3) the Knipovich Ridge, 4) the Molloy Ridge, 5) the Lena Trough, and 6) the Gakkel Ridge. After continental rifting at 60-50 million years ago, around 2.5 million km2 of oceanic seafloor has formed by seafloor spreading - resulting in the formation of the Norwegian- Greenland Sea and the Eurasian Basin. This northernmost part of the global ridge system is anomalous in several ways: The seafloor spreading takes place at an ultraslow rate (less than 2 cm/y) with spreading rates decreasing northward to around 1 cm/y at the Gakkel Ridge - which is the most slow-spreading ridge on Earth. As a result, the volcanic activity along the northern part of the AMOR is low, the oceanic crust is unusually thin (around 3,5 km at the Knipovich Ridge, Kandilarov et al.2010), and the rift valley is deep (average water depth > 3 km). In the southern part of the AMOR, the ridge system is affected by the Icelandic plume and a hot spot below Jan Mayen. The ridge-plume interaction results in higher volcanic productivity, unusually thick oceanic crust (9-11 km, Kandilarov et al. 2012) and shallow ridge segments (1500-100 m). The AMOR also display contrasting spreading regimes, whereas some super segments are dominated by orthogonal spreading (Kolbeinsey and Gakkel Ridge) others are characterized by highly oblique spreading (Mohns and Knipovich ridges). Some ridge segment displays asymmetric spreading, like the Mohns Ridge where core complexes preferentially form along the northwestern flank. Together these variations in ridge characteristics results in large diversity of hydrothermal systems and associated mineral deposits.

Jan 1, 2018

By Carl L. Kaiser

This abstract discusses selected recent technology developments at the Deep Submergence Lab at the Woods Hole Oceanographic Institution aimed at fundamentally changing the nature and scope of AUV operations in the deep ocean. The Autonomous Underwater Vehicle (AUV) Sentry is described in its current configuration with discussion of emerging capabilities. Telepresence enhanced AUV operations are discussed including moving both operations and data processing personnel off the vessel. Autonomous Surface Vessel (ASV) aided AUV operations are discussed including recent experiments where an ASV provided both navigational aiding and a satellite based relay for acoustic communication of telemetery and mission redirection. New flexible communications strategies to perform intervention and manipulation tasks from an untethered vehicle are discussed. The abstract concludes with a brief discussion of industrial collaborations, including the newly launched Center for Marine Robotics.

Sep 14, 2011

By Gale L. Hubred

Kennecott?s Ledgemont Laboratory developed the Cuprion Process to recover metal values from manganese nodules in the early 1970s. A reducing leach of monovalent cuprous ion attacks the manganese oxide matrix, converting the manganese dioxide to manganese carbonate and releasing the copper, nickel, cobalt, and zinc as ammine complexes. Cuprous ion is generated by contacting leach liquor with carbon monoxide. Copper, and nickel, are recovered by solvent extraction and electrowinning. Cobalt is precipitated as cobalt sulfide and recovered as cobalt powder. Manganese, molybdenum, and zinc can be recovered optionally but have not been included in this process. Kennecott authors have described aspects of the process, but the Cuprion process has not been revealed except in patents. Tables are included for capital and operating costs and revenue. Even though economic recovery of nodules is not anticipated in the foreseeable future, some of the process steps may have application in other places. The Ledgemont Laboratory was a unique operation we think worth documenting. The report is based upon work done up until the mid 1970s. The report represents the work of the entire Kennecott nodule team. It is this author?s intention to save this result and credit the work of that nodule team. The paper is dedicated to the memory of Dr. Herbert Barner, a key member of the team who died in 2003.

Jan 1, 2005

By Ivar Eskerud Smith, Ole Jørgen Nydal, Niranjan Reddy Challabotla, Svein Sævik

INTRODUCTION Airlift pumping, utilize compressed air that is injected at the bottom of a vertical pipe submerged in the water, reduces the mixture density inside the pipe and lifts the liquid or mixture of liquid and solids. This type of pumping technology, which is simple and without moving parts submerged in water, which provides several advantages compared to the mechanical pumping. Airlift is used in various difficult pumping applications such as transport of fluids corrosive to metals, explosives, nuclear and toxic materials in chemical industries, diamond mining and coal transport. Application of airlift to deep sea mining conditions was investigated by extensive laboratory experiments [1], theoretical analysis [2], and limited proof of concept field studies [3] starting in 1970’s with the discovery of huge amounts of manganese nodules discovered on the seabed at a depth of ranging from 4000 to 6000 m . Even after extensive investigations over the last five decades, there exists no commercial application of airlift technology for lifting of minerals. The major problems with the application airlift for deep ocean mining was (a) lack of control over the expansion of the injected gas, which increases the velocity in upper part of the riser pipe (b) lower efficiency compared to mechanical pumping [3]. Different flow regimes are encountered in airlift pumping: bubble, slug, churn and annular flow. Annular flow regime is the least efficient in lifting of particles and churn flow has better efficiency [3].

Jan 1, 2018

By James R. Hein

Barite and Fe-Mn-oxide deposits that occur along faults in the Southern California Borderland formed by low-temperature hydrothermal processes. The Borderland region consists of block-faulted continental crust within the broad transform boundary of the North American plate. The fault-bounded basins are anoxic and partially filled with hemipelagic and turbidite sediments. Barite was collected from four dredges and a submersible dive (DSV4-355) in the southern California Borderland, and was collected from two sea-cliff sites along the Palos Verdes Headlands near Los Angeles. Barite at these seven locations occurs along strike-slip and basin-margin faults from the shoreline to 1800 m water depth. Submersible observations showed a series of mounds up to 10-m high composed of friable, white barite associated with diffusely venting milky fluid; the mounds support large benthic colonies, including tube worms (Lonsdale, 1979). Barite samples recovered from dredges are brown, green, and white and range from porous, vuggy fragments to massive fragments cut by banded barite veins. Samples from two dredge sites contain fossil worm tubes 1-3 mm in diameter and >10 cm long. All the samples are nearly pure barite, with only minor to trace amounts of other minerals. Chemical analyses show 94-98 wt. % BaSO4, low total rare-earth element (REE) contents (<45 ppm), Sr contents from <2 to 10,000 ppm, and Hg contents up to 1 ppm. Chondrite and shale-normalized REE patterns show light REE enrichments and large positive Eu anomalies. These REE pattern characteristics are typical of marine hydrothermal fluids and minerals. Sulfur isotope ratios (d34SCTD) from +21.6 to +67.4? range from seawater values (+21?) to exceptionally high positive values. Strontium isotope ratios are lower than the modern seawater ratio as well as the seawater ratio that existed at the time of deposition of the host rocks.

Jan 1, 2002

By Carsten Rühlemann

Between 2008 and 2013, the German Federal Institute for Geosciences and Natural Resources (BGR) carried out five exploration cruises to the German license area in the eastern Pacific Nodule Belt. The first two expeditions were mainly dedicated to multibeam mapping to obtain an overview of the seafloor topography and acoustic backscatter strength. These data were used to identify ten to fourteen prospective nodule fields for potential future mining, which together cover about 16% of the total license area of 75,000 km2. During the last three cruises, three of these potential mining areas were explored in detail. For this purpose, the BGR developed a suite of exploration methods to map nodule size distributions and nodule abundances. These methods include acoustic surveys with vessel-based multibeam systems as well as near-bottom video mapping complemented by in situ sampling. The economically most valuable field has a size of ca. 2,000 km2, of which 34% is covered by medium to large nodules (> 4 cm long axis of nodules) with an average abundance of 22.4 kg/m2 and 44% is covered by small nodules (< 4 cm) with a mean abundance of 17.5 kg/m2. The total mass of nodules in this field comprises more than 30 million tons wet weight and could sustain deep-sea mining for at least 10 years.

Sep 14, 2011

By Richard Mills

Autonomous Underwater Vehicles (AUVs) are proven technologies used across market segments for survey, exploration and environmental monitoring tasks. When coupled with other autonomous platforms or sensor packages AUVs become part of an holistic system approach to exploration and environmental assessment and monitoring. Recent developments have seen AUVs deployed remotely with instantaneous access to data via the cloud. Our goal is to deliver the capabilities of each of these elements and present a cohesive data set with automated processing tools over a cloud based interface. nmanned Technology AUVs The HUGIN AUV System is the most commercially successful AUV ever built. Operated as a single vehicle, or as part of a swarm, HUGIN’s area coverage rate is unrivalled. Equipped with a comprehensive sensor package including Kongsberg’s synthetic aperture sonar, it collects a data set. Some of these data are processed in-mission to enable operators to readily access it when the vehicle is recovered. HUGIN is well suited to mining survey and exploration. Capable of reaching 6000 metre depths and conducting missions greater than 60 hours, HUGIN collects seabed sonar imagery, sub-bottom profiles, laser and camera images plus environmental data, with sensors running concurrently.

Jan 1, 2018

By Karsten Hagenah, Tor Jensen, Jens Laugesen, Øyvind Fjukmoen, Lucy Brooks

This paper describes operational environmental threshold levels for exploitation of mineral resources in the deep sea. Such criteria are needed to be able to monitor and control deep sea mining with respect to the stringent environmental requirements that are needed. It is recommended to use existing environmental threshold levels for comparable activities where such are existing. Fields of application are mainly but not exclusively seabed mining operation activities under the governance of the International Seabed Authority (ISA). The threshold levels and limits mentioned in this paper are proposed recommendations based on other activities than seabed mining but are a proven and accepted approach in other maritime industry activities. An example of such other activities with proven and accepted environmental threshold levels are Oil & Gas exploitation activities in the sea. Background The first exploitation of mineral resources is coming closer. At the moment regulations for exploitation for mineral resources in the Area are being developed by the International Seabed Authority (ISA). The ISA regulations will contain the framework related to environmental monitoring of exploitation. However, the regulations will not contain operational environmental threshold levels for the Contractor.

Jan 1, 2018

By Karsten Hagenah, Tor Jensen, Jens Laugesen, Øyvind Fjukmoen, Lucy Brooks

This paper discusses operational environmental threshold levels for exploitation of mineral resources in the deep sea. Such criteria are needed to be able to monitor and control deep sea mining with respect to the stringent environmental requirements that are needed. It is recommended to use existing environmental threshold levels for comparable underwater activities. Fields of application are mainly but not exclusively seabed mining operation activities under the governance of the International Seabed Authority (ISA). The threshold levels and limits mentioned in this paper are proposed recommendations based on other activities than seabed mining but are a proven and accepted approach in other maritime industry activities. An example of such other activities with proven and accepted environmental threshold levels are Oil & Gas exploitation activities in the sea. Background The first exploitation of mineral resources in international waters is coming closer. Presently regulations for exploitation for mineral resources in the Area are being developed by the International Seabed Authority (ISA). The ISA regulations will contain the framework related to environmental monitoring of exploitation. However, the regulations will not contain operational environmental threshold levels for the Contractor.

Jan 1, 2018

By Robert G. Ditchburn

The NW caldera hydrothermal vent field at Brothers volcano, of the Kermadec-Tonga arc, has associated massive sulfide mineralization. This includes an abundance of black smoker chimneys that contain significant concentrations of copper, lead, zinc and gold (de Ronde et al., 2005; de Ronde et al, 2010, under review). [ ] The oldest volcanic massive sulphide (VMS) samples recovered so far from Brothers have been dated using radiometric methods at GNS Science and found to be c. 1000 years old. By contrast, a volcanic cone that has formed in the southern part of the caldera has no associated VMS. Only elemental sulphur and Fe-oxide crusts are present here, samples of which have been analysed for their trace elements. From d34S values of sulfates and native sulfur, and the volume of gas (dominated by CO2 and H2S) discharging at the cone site, elements being deposited here are considered more directly magmatic in origin (de Ronde et al., 2005; 2010 under review). It has been discovered that deep-seated changes in volcanic activity at Brothers affect the NW caldera and cone site simultaneously, though the mineralogy at each site is so very different. Thus, the cone site is being studied to determine if elements being deposited there can be used as predictors of potential future VMS mineralisation as similar sites have been found at other volcanoes along the Kermadec arc and elsewhere. The frequency of these deep-seated magmatic events is considered important in the formation of Cu-Au-rich mineralization along arcs. The analysis of Fe within resulting hydrothermal plumes (surveyed by surface vessels), and trace elements in rock and mineral samples, are used to help determine the influence of magmatic contributions to the hydrothermal system. To verify that plumes are a reliable proxy for hydrothermal events depositing iron on the seafloor, Fe-oxide crusts from Brothers volcano cone have been dated to see if their emplacement coincides with highly Fe-enriched plumes in the water column. The radiometric dating techniques developed for barite-rich VMS, i.e. using 228Ra and 226Ra, were unsuitable for the Fe-oxide crusts because 210Pb was the only isotope detected by gamma spectrometry. Therefore, new techniques using 210Pb, 10Be and arsenic have been established.

Jan 1, 2010

By Nobuyuki Okamoto

The 21-year long-term Japan-SOPAC Cooperative Deep-sea Mineral Resources Study Programme was completed in March 2006. The Programme, which commenced in 1985, has seen numerous marine research surveys being conducted within the Exclusive Economic Zones (EEZs) of 12 SOPAC member countries (Figure 1). The various research and government institutions that have been closely involved in this longstanding Programme include: the Japan International Cooperation Agency (JICA); Japan Oil, Gas and Metals National Corporation (JOGMEC) (formerly, the Metal Mining Agency of Japan, MMAJ) and relevant ministries of the participating Pacific Island governments.

Sep 24, 2006

The seafloor occurrences of KODOS ferromanganese nodules can be classified into four facies based on the morphological types of nodules recovered and seafloor photographs. Facies A, B, and C are relatively unimodal whereas Facies D is bimodal in the size distribution of nodules. Both Facies A and B are highly covered by sediments, but Facies B is higher than facies A in nodule density. Facies C has a high density of small nodules and many traces of bioactivity. Facies D is irregular in nodule density, but occurs close to basement near scarps (Fig. 1). The transparent layer (TL) on subbottom profile records (von Stackelberg et al., 1987) is composed of three sedimentary units, which in cores are distinguished by color. The uppermost Unit I is postulated to be deposited during the past 0.21 Ma and the middle Unit II between 0.42 Ma and 0.21 Ma (MOMAF, 1997). There exists a hiatus between Unit II and Unit III. Unit III was deposited from 3.5 Ma to 1.5 Ma as determined by 10Be/9Be and/or 87Sr/86Sr dating (MOMAF, 2004). Internal textures observed on cut sections of nodules suggest four stages of nodule formation (Choi et al., 2000). The nuclei are either unbroken old nodules probably of hydrogenetic growth (1h and 2h) in Facies A and C, or nodule fragments probably of early diagenetic growth (2d) in Facies D, whereas there are both types in Facies B. The layers surrounding the hydrogenetic nodule nuclei are of hydrogenetic growth (3h and/or 4h) in Facies C, and are of early diagenetic growth (3d and/or 4d) in Facies A, B, and D. The layers surrounding the early diagenetic nodule fragments are mostly of early diagenetic growth (3d and 4d) in Facies A, B, and D. But hydrogenetic encrustations are also found as surface layers on the top in Facies B (Fig. 2).

Jan 1, 2005

By Tony van der Steen

Subsea mining system are designed for the following, principally different, tasks: Dreding - The destruction and removal of seabed sediments overlaying the bedrock. Cleaning - The competence of the system to systematically remove the deposits from an undulating hard bedrock with irregular pulleys, channels and fissures. Factors that influence the choice of dredging equipment for a specific project are project requirements such as environmental conditions, location and water depth. However, the most important selection criteria are soil conditions. As a consequence, possible dredging systems, must be evaluated for the following, principally different, characteristics: Dredging proficiency - The destruction of the strata by the equipment. System stability - The capability of the soil to support the subsea equipment The above parameters are determined by the strength characteristics and the bearing capacitv_ of the soil. The author describes the processes involved in excavating the subsea deposits and (transporting the gathered soil as a water-soil mixture to the surface using different excavation and transport methods.

Jan 1, 1998

By Rahul Sharma

Although, mining of minerals such as polymetallic nodules and sulphides from the deep sea floor has been delayed due to the combination of factors such as current availability of Cu, Ni, Co, Mn (and other metals) on land and their fluctuating prices; these deposits are still considered as the alternative source for metals in the 21st century. Exclusive rights for exploration in the ?Area? (beyond the national jurisdictions of any country) given to eight countries and consortia by the International Seabed Authority and the estimated resource of 300 million tonnes in a typical area of 75,000 km2 is expected to yield about $17.5 billion (at December 2008 metal prices) in 20 years life span of a single nodule mine-site. In order to recover 3 million tonnes of nodules, an area of 300 sq km only will be mined annually (i.e. <1 km2/day) for an optimum abundance of 10 kg/m2. However, during mining, large quantity (22 tonnes/day) of sediments associated with nodules would be resuspended that could lead to certain environmental impacts on the benthic ecosystem. Several small-scale benthic impact experiments in the Pacific and Indian Oceans, have given some insight into the possible environmental impacts and the restoration processes, but the possibility of extrapolating these findings to a commercial mining scale remains an issue to be considered. An estimated capital expenditure of $1.05 billion and operating expenditure of $4.2 billion for a single deep-sea mining venture will have to be weighed against the availability of mineral ores on land as well as the metal prices in the world market. None-the-less, development of technologies for mining and metallurgical processing, as well as formulation of regulations and guidelines for potential ?contractors? to mine these minerals have been progressing consistently. These coupled with recent efforts by certain ?entrepreneurs? to initiate mining of seafloor massive sulphides in the EEZ of certain countries, indicate the continuing interest and support the perception that such deposits could well be the future sources of metals. This paper analyzes the current status and discusses the economic, environmental, and technical issues that need to be addressed for sustainable development of deep-sea minerals.

Jan 1, 2010

By S. W. Chang, James R. Hein, S-R. Lee, A. Zondervan, H. Choi

"Nine Fe-Mn nodules from the extensive nodule field in the east of Campbell Plateau of southwest Pacific Ocean beneath the Deep Western Boundary Current (DWBC) and Antarctic Circumpolar Current (ACC) were analyzed for the 10Be/9Be dating by AMS (Accelerator Mass Spectroscopy) at IGNS, New Zealand.Several types of nodule morphology were identified including distinctive discoidal forms with overgrowths resulting possibly from overcrowding and partial sediment burial. Five principal nodule facies were also recognized by location and occurrence (Fig. 1) (Wright et al., 2005). Fe-Mn nodules show various concentric internal growth textures, such as, cuspates, large parabolic cuspates, pseudo-columnar, columnar, globular, and laminated, which vary even in a nodule with hydrogenetic, early diagenetic, or mixed origin. Each texture shows micro-textural varieties and different mineralogy and/or chemistry. The genesis of each internal texture was indicated by the REE patterns, the mineralogy of Mnoxides, and the Mn/Fe ratios."

Jan 1, 2017

By Matthew Kowalczyk, Steve Bloomer, Peter Kowalczyk

"Mineral deposits found near seafloor hydrothermal venting are of great economic interest. Valuable metals such as gold, copper, zinc, and other polymetallic sulfides are found in appreciable grades in seafloor massive sulfide (SMS) deposits associated with these vents. For mapping these deposits, electromagnetic prospecting is one geophysical method that is very useful because copper/gold rich deposits are highly conductive.Ocean Floor Geophysics (OFG) in 2008 developed the first EM system to successfully map the limits of conductive mineralization in a survey at the Solwara 1 deposit (Kowalczyk, 2008). Since then, towed coincident loop time domain systems have been developed by Waseda University (Nakayama and Saito, 2016) and have successfully detected known mineralization buried at 30m depth. Using a deep tow controlled source electromagnetic (CSEM) array, very clear anomalies have been measured (Murton, 2017) over known mineralization at the TAG field on the mid-Atlantic ridge.In 2014 and 2015, OFG partnered with Fukada Salvage and Marine Co. Ltd. and the Scripps Institution of Oceanography to map methane hydrate deposits off the coast of Japan using a towed controlled source electromagnetic (CSEM) system developed by Scripps. These hydrate deposits are resistive targets, and the Scripps system successfully mapped subsurface electrical resistivity distributions to depths of several 100 metres below the seafloor. OFG is attempting to extend the Scripps CSEM technology to map subsurface conductive SMS deposits to a similar range of depths below the seafloor."

Jan 1, 2017

By Katsuya Tsurusaki

Commercial mining of manganese nodules is expected to begin within the next 20 to 50 years in large areas of abyssal sea floor in the Pacific Ocean. While deep sea mining is expected to realize significant quantities of rare metals that are needed for modern technology, the mining operation will cause extensive resedimentation over large areas of deep sea floor, the effects of which are thought to be harmful to the benthic community. Our present knowledge of deep sea benthic ecology is so limited that we cannot predict the magnitude of the impact. In November 1994, the United Nations Convention on the Law of the Sea was enforced and giving added impetus to improving our understanding of the effects of future mining operations. In order to fully understand the impact of deep sea mining and to mitigate the harmful environmental effects, it is necessary to accumulate more information on the deep sea environment and benthic communities. To achieve these objectives and to understand the relationship between resedimentation and biological reaction, artificial impact experiments are being conducted by the USA and Germany. The former named BIE (Benthic Impact Experiment) began in 1991 and is being performed by NOAA (National Oceanic and Atmospheric Administration of the United State of America) in the North Equatorial Pacific Ocean. The latter named DISCOL (Disturbance and Recolonization Experiment in the Deep South Pacific Ocean) was started in 1989 and is being conducted in the South Equatorial Pacific Ocean by a scientific group from Hamburg University. The Metal Mining Agency of Japan (MMAJ) is also carrying out environmental studies. These studies, commenced in 1989, are being conducted in association with NOAA and include an experiment named the Japan Deep Sea Impact Experiment (JET).

Jan 1, 1996

Although Mn, Fe, Cu, Ni, and Co have been the main interests since the ferromanganese nodules had been found, the other major components such as Si and Ca might be very important controlling factors in the processing due to the locally variable content. It is because of the fact that SiO2 and CaO are added to decrease the smelting temperature in the reduction-smelting method for manganese nodule processing. We have compiled the 707 chemical data for KODOS (Korea Deep Ocean Survey) ferromanganese nodules, which have been acquired from 1994 to 2001 and have been also standardized from 2001 to 2003 to avoid the discrepancy between the data sets. All 707 chemical data were used for the hierarchical cluster analysis to get the elemental correlations and also classified by the morphological types. The averages from each station were classified by the facies groups (Fig. 1) and the localities. Then all data are plotted on the SiO2-CaO-MnO phase diagram at 1773°K to compare with the best compositional area in the nodule smelting. Variations and distributions of SiO2 and CaO as well as those of Mn, Fe, Cu, Ni and Co in KODOS ferromanganese nodules were also reviewed. The mineral phases assigned by the cluster analysis are CFA (Carbonate Fluorapatite), Fe-oxide, Al-silicate, and Mn-oxide. MnO contents are generally higher than SiO2 contents in most of the morphological types except for the Is- and It-type. The Dt- and Tt-type show wider range and the E-types show high anomaly in their CaO contents. The stations which belong to facies group A and B show generally higher MnO contents than SiO2 contents, however, the stations of facies group C and D show wide range in their MnO and SiO2 contents.

Jan 1, 2004

By Ulrich Schwarz-Schampera

Submarine hydrothermal vents and associated mineralization on the Tonga arc have been identified in the summit calderas of two shallow-water volcanoes. The highest temperature vents (up to 270°C) occur at water depths between 430 and 540 meters below sea level (mbsl) near the summit of one volcano at 24°S (volcano 19). Clusters of large barite, anhydrite, and sulfide chimneys on the summit cone are vigorously discharging clear hydrothermal fluids with temperatures on the seawater boiling curve. There is abundant evidence of phase separation and associated gold and base metal precipitates. Pyrite, marcasite, wurtzite-sphalerite, tennantite, and chalcopyrite line the interiors of the highest temperature vents. Acid-sulfate alteration of basalts and basaltic andesites is evidenced by intense silicification and the presence of abundant alunite. One volcano at 21°S (volcano 1) has a chain of explosion craters on the flank of a neovolcanic scoria cone and associated massive pyrite, barite and native sulfur deposits at a water depth of 210 mbsl. Intergrowths of pyrite and enargite are associated with intensely argillic altered basaltic andesites. The reported alteration and Au-enriched mineralization styles of these vent fields are similar to other shallow water hydrothermal systems at island arc volcanoes and contribute to the diversity of seafloor hydrothermal activity in the western Pacific region.

Jan 1, 2010