Search Documents

By Ashirbad Satapathy, Sanket Rawat, Ramanand Shukla, Ravi Kant Mittal

Bearing capacity factor (Nq) and Adhesion factor (α) are the key parameters for analyzing the load carrying capacity of pile foundations embedded in cohesionless and cohesive soils respectively. Numerous models are available in the form of charts or equations for the computation of these parameters and hence, have been adopted by most of the International and National standards. Indian Standard for the Design and Construction of Concrete Pile Foundations, IS 2911–Part 1 (2010), also makes use of charts detailed in its Annexure B. However, the sources of these charts have not been specified clearly, making it difficult to back-refer to the actual models to assess their basis for resolving any critical scenarios encountered during design. The present study aims at acquiring a distinct understanding of the development of these charts in order to bring more clarity to the design process of pile foundations. The given charts have been compared with various models specified in existing literature and international standards for the calculation of Nq and α for both driven and bored piles and hence, the basis of Indian Standard charts has been identified. Moreover, it is evident that the use of these charts complicates the process of automation of analysis and design of pile foundations as well as the associated optimization studies. Additionally, the manual entry of data especially, from the logarithmic graph of Nq, escalates the chances of error thus, making it a critical concern for design offices. Therefore, this paper also presents a non-linear regression model for Nq and α, developed using NCSS software for both driven and bored piles. Through multiple iterations, the value of coefficient of determination for Nq and α has been found to reach greater than 0.995. The developed equations can be simplistically used for both manual and automated analysis of pile foundations.

Nov 1, 2022

By Paul J. Lewis

Estimation of the axial side shear resistance of drilled shaft rock sockets is directly related to the unconfined compressive strength of the bedrock. Commonly, the mean unconfined compressive strength value is calculated from a range of laboratory test results and is used to estimate the side shear of the bedrock. This paper presents the results from a full scale axial load test performed on an 8.5-feet-diameter drilled shaft rock socket, and compares measured side shear values to estimated values for two different rock strata. Measured side shear values correlated well with the design value calculated for the ?strong? rock stratum, but did not correlate well with the design value calculated for the ?weak? rock stratum. The mean unconfined compressive strength was used to calculate the side shear in both strata, but review of the laboratory data indicates that this value may not have been appropriate for the weak stratum due to a large variation in the laboratory test results. Also included in this paper is a discussion of the subsurface conditions, the laboratory test results, and the methodology used to design the drilled shaft rock sockets for axial and lateral resistance.

Jan 1, 2013

By L. D. Johnson

12 groups of 12 precast prestressed (PCPS) piles were driven in the lagoon of Kwajalein Island to support a dry dock. Pre-construction investigation of the calcareous coral sands and static pile loeid tests were performed to determine if the 7.9 by 7.9 cm (20 by 20 inches) by 26 m (85 ft) long PCPS piles embedded to a depth of 16 m (53 ft) would adequately support the dry dock. Driving records for production piles indicated that the blowcounts of the piles at the fincil embedment depth became substantially less than expected as piles wssre driven further toward the lagoon end of the dry dock and decreased to as low as 2 blows/ft. A supplemental investigation that included a static load test on a production pile, the driving of an indicator pile, and restrikes indicated that the pile foundation has adequate bearing capacity. The observed bearing capacity appears to be effected by several mechanisms including breakdown of cementation between sand particles, densification of the sands during driving, and dissipation of excess pore pressures and recementation after driving.

Jan 1, 1993

By Ryan Weaver, Travis Coleman

The drilled shafts that support transmission lines and substations have been increasingly subject to testing to assess the integrity of placed concrete. Cross-hole Sonic Logging (CSL) has been used, but large diameter shafts with challenging site access are generally more favorable to Thermal Integrity Profiling (TIP) testing. TIP testing assesses the shafts based on measurements of the concrete temperature during curing. The TIP results provide assessment of integrity both within and outside the cage, along with information about the alignment of the cage and concrete cover. This data has allowed shafts with imperfect results to be subject to more detailed structural evaluations. However, it may not be well understood how to use this additional information by designers and engineers. The purpose of this paper is to present TIP results of transmission line foundations, both with and without issues with integrity, including cage shifting, minimal concrete cover, or soil inclusions. The intent is to provide general guidelines of the issues that merit additional investigation and those that should be recognized as inconsistencies inherent to underground construction. BACKGROUND This paper is intended to discuss some of the drilled shaft evaluations made when TIP testing is performed. The authors of this paper were recently involved with a transmission line project that was designed and constructed for a Confidential Utility Client located in the Midwest United States. The project was delivered as an Engineering, Procurement, and Construction (EPC) contract with the electrical line construction company as the prime contractor. The contractor then subcontracted several parts of the work which included engineering for transmission line and foundation design, foundation construction, and third-party testing intended to evaluate the concrete homogeneity and integrity of the place concrete in the deep foundations. The testing method selected was Thermal Integrity Profiling Method B, which uses thermal sensors embedded in the concrete. The TIP testing was administered by Mr. Travis Coleman with GRL Engineers, Inc. Mr. Ryan Weaver with Burns & McDonnell served as the owner’s engineer and technical consultant for the utility and was responsible for reviewing submitted TIP reports and providing recommendations to the utility on their acceptance, and if there were any issues that would warrant further discussion and analysis.

Jan 1, 2019

By J. Erik Loehr, Minh Uong, Andrew Z. Boeckmann, Sarah G. Myers

"The University of Missouri performed a lateral load test program involving 32 drilled shaft load tests for the Missouri Department of Transportation (MoDOT). Tests were performed at two MoDOT geotechnical research sites, and all shafts were founded in shale. Shafts were instrumented to measure the displacement of the shaft head, and the structural response of each shaft was interpreted from strain gage data and from ShapeAccelArray (SAA) data. The SAA is a chain of rigid segments with sensors that use MEMS (microelectromechanical systems) technology to measure the tilt of each segment/joint. The measuring principle of the SAA is therefore similar to that of an inclinometer. The SAA device was placed in a casing installed in the center of each test shaft to provide a continuous record of deflection along the length of the shaft throughout each test.Bending moment profiles were calculated from strain gage data and from SAA data. Interpretation of bending moments from measurements of strain (via strain gages) and displacement (via SAA) is a nontrivial exercise, primarily because the bending stiffness, EI, is nonlinear and greatly influenced by concrete cracking, which is difficult to predict. The procedure used for this work predicted values of bending stiffness along the length of the shaft as a function of the bending curvature, which was interpreted from the SAA data. Values for bending stiffness as a function of curvature were computed using Ensoft LPile v2012. Bending moment profiles from SAA data were typically similar to those from strain gage data. The SAA bending moment profiles were often “noisier” than the strain gage bending moment profiles, but the SAA bending moment profiles had more data points since the SAA chain was continuous from the top to the bottom of each shaft."

Jan 1, 2017

By Garland Likins, Gray Mullins, George Piscsalko

"Quality control of drilled shafts is greatly dependent upon the practices of the site personnel. For drilled shafts cast under slurry, inspection of the hole prior to concreting is very difficult or impossible. There are numerous non-destructive test (NDT) methods currently available to assess the integrity of drilled shafts. This paper will discuss the theory and use of an emerging NDT technology known as Thermal Integrity Profiling (TIP). The Thermal Integrity Profiling method measures the elevated concrete temperatures that occur during the hydration process. These temperature measurements are made along the length of the pile and can determine the integrity over 100% of the pile cross section, both inside and outside the reinforcing cage. With the known shaft volume information, TIP can evaluate the effective shaft radius at each measurement location. With the increased use of TIP on highway projects, there is a need to have standard criteria for shaft acceptance. Shaft acceptance criteria can be based upon thermal measurements and subsequent analysis of the data to determine the average shaft radius, local concrete cover, and cage alignment. With this additional information obtained via the thermal testing method, acceptance methods based upon concrete cover can be developed. In this paper the Thermal Integrity Profiling method will be described, results from a case history will be discussed, and an acceptance criteria based upon concrete cover will be proposed.INTRODUCTIONDrilled shafts are an attractive foundation element in many applications due to their large axial and lateral capacities. When drilled shafts are cast in a dry hole, it is possible to inspect the hole prior to casting, allowing for very basic level of quality control, although the shape of the completed element is still unknown without some form of post construction testing. When drilled shafts are installed where soil conditions are unstable, the shafts will often be cast under slurry to support the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to impossible to accurately and efficiently inspect the hole prior to casting concrete and it is equally difficult or impossible to inspect the shaft during the casting process"

Jan 1, 2016

By George Moses K, Mahendran K

Grouting is performed in rock masses in order to increase its strength properties and also to reduce the seepage. In the design of underground structures such as tunnels or caverns located in weak rock masses, grouting plays an essential role. Grouting is a complex process demanding high degree of skill and knowledge in understanding of grout flow and requirements for certain geological conditions. This paper discusses the design process for grouting in rock masses adopted for a cavern project and the practical difficulties faced during the execution at site. The design parameters of grouting includes the injection pressure, grout material properties and stopping criteria. The paper also discusses the various tests performed at site to evaluate the efficacy of the grouting process which was initially defined based on the design and previous experiences. The final grouting scheme suiting to the present geological condition is arrived based on the test results. The practical difficulties faced during the execution and the measures taken to overcome these are discussed in detail. This work shows the importance of state of art in the development of a grouting process based on geological and hydrogeological conditions prevailing at site and can be helpful in grouting design for weak rock masses.

Nov 1, 2022

By Luca Pingue, Regine Jagow-Klaff, Franco Muratore, Carlandrea Albonico, Damiano Frontini, Rudolf Wernecké

This paper describes an artificial ground freezing (AGF) application carried out to ensure both watertightness and structural support for the safe excavation of four cross passages of the Forrestfield Airport Link (FAL) project in Perth. The line will deliver 8.5 km extension of the existing urban rail network connecting the growing eastern suburbs of Perth with the existing suburban rail network. The proposed soil improvement technique is adopted as a smart alternative to jet grouting from the surface since the use of heavy equipment with long vertical mast was not allowed due to the line underpassing an airport in operation. In this paper, details of the challenges and lessons learned during both design and construction phases are given. Furthermore, it is described the geometry and the installation of freeze pipes in presence of a massive steel frame, ventilation system and slurry pipes of the tunnel boring machine (TBM) in operation. It is also illustrated the web monitoring system to allow key personnel to follow in real time the development of soil temperatures, tunnel convergences and ground surface deformations as well as changes in the interaction between international parties involved due to the COVID-19 pandemic.

May 1, 2022

By Chetan D. Savani, Mike K. Muchard

The necessity to evaluate undocumented foundation lengths is essential in assessing the useable life, need for scour protection, retrofitting, or full reuse of existing bridge foundations. For this purpose, Parallel Seismic Testing (PST) has the best accuracy and is applicable to the widest range of foundation configurations used in bridge construction of any test method. Although not limited to bridges, PST case studies are presented involving two bridges. To preface the case study discussions, an overview of the PST method is given along with its results and analysis thereof. In one of the cases, we were afforded the rare opportunity to see the existing piles being extracted long after the PST testing program was completed. The resulting Class A prediction reaffirms the accuracy of the method. Versatility of the PST method is also exemplified in the two cases presented, where unique situations from complex foundation systems were overcome by analysis to provide successful results.

By Daniel Magill, Jim Gentry

"Acrylamide chemical grout (C3H2NO) has been successfully used for over 50 years to control groundwater and stop infiltration. This paper will address three unique projects involving the control of groundwater with each study providing special circumstances and geological conditions: encapsulation of radioactive hazardous waste in the United States, a tailings dam for a large copper/gold mine in Argentina and 27 miles of leaking subway in Canada. The primary reasons for selecting acrylamide grout were based on the following characteristics: thinnest chemical grout on the market, a true solution grout which contains no suspended solids in the blended product, flexible gel set times, and a 362 year half-life in soil as determined by the U.S. Department of Energy.INTRODUCTIONChemical grouting has been successfully used for over fifty years to control the movement of groundwater in a wide variety of applications including:•, Hazardous Waste Containment•, Subways & Tunnels•, Mines & Tailings Dams•, Concrete & Earthen Dams•, Underwater Structures•, Beneath/Around Underground Structures•, Mainline Sewers, Laterals, Manholes•, Large Soil Stabilization ProjectsThis presentation will review three projects where chemical grout was utilized to address some very difficult water control challenges, each providing special circumstances and geological conditions:1. Pre-construction seepage control at a mine tailings dam2. 27 miles of leaking subway3. Encapsulation of radio-active hazardous wasteThe reasons for selecting acrylamide grout as the solution for controlling groundwater in these selected projects were based on the following characteristics:1. Acrylamide grout is the thinnest chemical grout on the market2. No suspended solids which allows acrylamide grout to travel anywhere water can travel3. Flexible gel set times from 5 seconds to 10+ hours4. U.S. Department of Energy studies conclude that acrylamide chemical grout has a 362 year half-life in soil and can reduce the permeability of rock/soil to less than 10-8 meters per second (m/s)"

Jan 1, 2017

By Ryan T. Smith, Anthony Sahj, Alexander T. Darnell

Every second can count when trying to board a departing flight or catch a ride-share to your final destination. Hartsfield-Jackson Atlanta International Airport is in the midst of a project that aims to cut about 13 seconds between automated people mover trains (Plane Train) that move passengers between the terminals and concourses. The project involves extending the Plane Train tunnel west from its existing terminus under the domestic terminal. Working from inside non-public areas of the terminal, Keller North America, Inc. (Keller) incorporated systems of micropile-supported steel beams and grillage to both underpin existing columns prior to tunneling and support open-cut excavation at the tie-in of the new to the existing tunnel. Dewatering aided in mining a challenging section at the start of the drive of the mixedface, sequentially excavated tunnel and an automated instrumentation system monitored the performance of the construction and its impact to the terminal. Cut and cover egress and ventilation tunnels required braced support of excavation.

Oct 1, 2022

By Philip Derbyshire, Dale J. Scheffler

"Continuous Flight Auger (CFA) piling is a variation of Augered Cast-In-Place (ACIP) or augercast piling. In both cases a continuous auger with a hollow stem is used to drill a hole and a pile is formed by injection of cementitious material through the hollow stem as the auger is withdrawn. CFA differs from conventional American ACIP by the use of concrete rather than grout to form the pile, and by the type of equipment used to advance the auger into the ground and withdraw it. CFA installation uses a European style rig (i.e. fixed mast and rotary system) which can produce greater crowd and usually has a larger rotator or drill motor than the standard augercast setup. A standard augercast setup will consist of a lattice-boom crane and a set of leads to house the drill motor and auger. The auger size will range up to 24 inches (610mm). With CFA rigs larger diameter piles can be constructed, 24 to 36 in dia. (610mm to 915mm) are common and the technique has been applied with diameters up to 48-inch (1220mm). CFA makes use of sophisticated computer controlled monitoring systems, which have more recently been introduced for conventional ACIP piling. Developments in CFA have taken place over the last 25 years in Europe and particularly in the UK, but are relatively new in the USA. One application is in the construction of secant (overlapping) piled retaining walls. D.J. Scheffler Inc. recognized the potential of the CFA system following visits to the UK and has introduced its use into California for both secant piling and other applications.BACKGROUNDThe high price of real estate in many of the favored areas of California has increasingly led owners to want to build basements under their houses to increase the floor space available on a lot. Many of these areas are by the coast where the ground conditions are predominately granular and the water table is high. Conventional shoring and dewatering systems have often caused problems with adjoining properties. Clearly tangent walls are not suitable in these conditions because of leakage and loss of ground. The secant pile system, using CFA techniques, has proved very effective at overcoming the problems experienced by other methods. Other applications for CFA secant walls have included use for an emergency job on a highway following erosion caused by unusually heavy rainfall.METHODThe concept of secanting piles, whereby primary(female) piles are installed first and then secondary (male) piles are cut into the primary piles is not new. The method has been known for more than 30 years. Originally ‘Benoto’ grabbing rigs, developed in Japan, were used together with sectionalized double skinned casing and oscillators.This early method was slow, although very effective. More recently high torque rotary machines have been used. Contractors in the UK have increasingly used CFA techniques to further improve productivity of this type of piled wall. The improved capabilities of piling rigs available, as well as developments in concrete technology and instrumentation, have made this possible."

Jan 1, 2005

By F Debidin

The progressive rise of an H-pile during driving of an adjacent pile is described in this case history in which piles 15 to 18 m long were driven to end-bearing for the foundations for a 230 m long building. The use of a reaction beam-soil anchor system for compression load tests is discussed. The results of static load tests to determine pile capacity are compared with those obtained by the Pile Driving Analyzer and by theory. Unusual high temporary compressions were observed by field control staff. Proof testing was necessary to determine the need for restriking of some piles in which rise had occurred.

Jan 1, 2010

By Dario Libano

"The Line 5 Extension, in Sao Paulo, Brazil, is currently the most important investment in public transportation by Sao Paulo’s state government. It will connect the south part of the city to the city center, crossing through four other major Metro lines and stations; all currently in operation. The total extension of the line is 11 km (6.8 mi), and includes a new parking yard for the trains and 11 new stations. The Brooklin Station, one of the new stations due to be open and operating in 2016, has a unique geometry of five secant shafts.The original design included constructing five secant shafts stabilized by two plastic slurry walls using conventional grab technology. One slurry wall, along the Santo Amaro Avenue, was to contain the contamination plumes, and another was for temporary support to enable the excavation of the shafts. The final retaining wall design was changed to a concrete structural diaphragm wall that reduced the construction time of the shafts by half, allowing the contractor to meet the construction schedule. This solution also avoided dewatering effects in a geological region characterized by Quaternary sediments and environmental contamination plumes. It was the first time that a hydromill was used in such a situation in Brazil. The hydromill, by overcutting the panels, increased the quality of the joints, and decreased the probability of having seepage into the shafts. The hydromill also created a seepage barrier and avoided movement of the contaminated plumes.The GeologyLocal geology is composed of a superficial Quaternary soil, basically soft organic clays and sands and gravels. From the depth of 8 m (26 ft) until 18 m (59 ft), geology is composed by tertiary medium compact sand with thin silt-clay layers. From 18 m (59 ft) down, there are alternations between compact silt-sands layers with very hard clays layers. Each is approximately 5 to 10 m (16.4 ft to 33 ft) thick.The Initial Basic DesignThe original basic design of the Brooklin Station was to be constructed from five 40 m (131 ft) diameter intersecting circular shafts, all in a line along the axis of the Metro tunnel, in 555 days. In the excavation sequence, the odd shafts were first excavated, waterproofed and had part of their inside cast-in-place structure built before the even shafts were excavated. During the excavation of the even shafts, part of the odd shaft’s support was demolished and connected with the even support. A 0.8 m (2.6 ft) thick plastic slurry wall, acting together with the wire mesh reinforced shotcrete support, ensured the excavation stability around the five shafts."

Jan 1, 2014

By Tai Luu, Maxim C. Schisler, Yaser Taheri

The Stevens Gateway Project is an expansion of the Stevens Institute campus overlooking the Hudson River in Hoboken, NJ. The plans call for 90,000 ft2 (8360 m2) of new classroom, research, and student life facilities in new, 4-story buildings. The excavations for the building footprints were bounded by city streets and existing buildings, including the historic Carnegie Laboratory of Engineering, built in 1902. Pit underpinning was originally specified for the Carnegie building. However, given the depth of cut, construction time required for the 13 ft (4.9 m) deep pits would be substantial. The geotechnical contractor retained for the support of excavation work therefore offered an innovative active soil nail wall design that would meet project requirements in a shorter timeframe. Unlike the passive soil nail systems common in the industry that are chiefly used for soil slope stabilization, active soil nail walls contain pre-stressed anchor components to resist soil movement and limit settlement of soil and structures being contained. In addition to a discussion of the overall design approach of the active soil nail wall system, this paper will include a detailed description of its constructability and effectiveness. This project’s use of a conventional slope stabilization technique for an unconventional purpose may have positive implications going forward. INTRODUCTION Stevens Institute of Technology is a private university in Hoboken, New Jersey that sits on the cliffs of the City of Hoboken overlooking the Hudson River and Manhattan Island to the east of the campus. In recent years, the university has executed numerous plans to expand and upgrade its campus academic, student life, and residential facilities. One such project is the Academic Gateway Complex. The plan adds 90,000 ft2 (8360 m2) of new classroom, research, and residential facilities while also enhancing community connections by building a park to serve as a green corridor for the city. The proposed construction took place on the north and south side of 6th Street between Hudson Street and River Street. The project included the demolition of an existing university building followed by the construction of two, 4-story buildings on the north and south property lots. The north and south buildings will be connected by a second floor bridge spanning 6th Street. The buildings each contain a full basement extending from the proposed ground floor at approximately El. 41ft (12.5 m) to the basement subgrade at El. 26 ft (7.9 m). Each building will be constructed on respective mat foundations. Figure 1 presents an overview of the project area.

Jan 1, 2019

By Jogeshwar P. Singh, Mohamed Ashour

The Soil-Foundation-Structure-Interaction (SFSI) problem involves Kinematic Soil- Foundation Interaction occurring during large (cyclic and permanent) ground deformations as well as Inertial Foundation-Structure Interaction occurring during shaking all of which take place while the soil and possibly structural properties degrade with time. The design of the deep foundations for liquefaction induced lateral spread loads include estimation of passive pressure applied by the liquefied material as well as the amount of anticipated displacement. Coupled analyses for SFSI problems that account for liquefaction induced lateral spread and their interaction with the deep foundation system can be performed using sophisticated numerical modeling techniques based on finite element and/or finite difference methods using computer programs such as FLAC or OPENSEES. Such complete SFSI analyses are very tedious and expensive and not feasible for most projects. In 2011, California Department of Transportation (Caltrans) released guidelines for foundation loading and deformation due to liquefaction induced lateral spreading. This simpler prescriptive approach combines empirical and analytical methods through decoupled analyses using computer programs such as LPILE and SLOPE-W together with liquefaction induced lateral spread estimates based on published empirical equations. Pile group effects and pile caps are accounted for using a concept of super-pile. In this paper, we discuss the solution of the same lateral spreading related SFSI problem using computer program CGI-DFSAP (CGI-Deep Foundation System Analysis Program) based on the strain wedge theory that can account for liquefaction, lateral spreading, pile groups, pile caps and nonlinear behavior of piles in a more coupled manner to analyze the foundation system under the lateral spread loadings. CGI-DFSAP can be used to analyze piles in sloping ground conditions as well as piles beneath the abutments near a free-face slope. We have included Strain Wedge Model (SWM) solutions using CGI-DFSAP of several field and laboratory case studies of lateral spreading related to pile foundations. Finally, we have also included the SWM solution of one of the Caltrans (2011) example problems.

Jan 1, 2015

By Brian Isherwood, Tara Brown, Paul Kreycir, Jenny Earle

"The Shangri-La hotel and luxury condominium tower, recently opened on University Avenue in downtown Toronto, required eight levels of underground structure, four extending into the shale bedrock.Isherwood Geostructural Engineers was retained in 2007 by Anchor Shoring Limited to provide an alternative design-build solution to better address serious foundation risks. The site, bounded on three sides by City streets, abuts an existing 1957 14-storey building with five underground levels to the north. Sitting on the rock surface along the east perimeter under University Avenue runs the existing Toronto Transit Commission’s University Subway Line built by cut-and-cover in the 1950’s and which was believed to lie very near the property boundary at the southeast corner of the site.The bedrock under Toronto is known to contain very high locked-in horizontal stresses, much higher than can be resisted by shoring techniques, which result in inevitable wall movement when excavating deep into the rock. The strategy adopted to control the risk to the Subway, adjacent building, and major utilities is described in the paper, along with the comprehensive monitoring of movements, and their comparison to predictions.The ProjectThe 66-storey Shangri-La hotel and luxury condominium tower, recently constructed on University Avenue in downtown Toronto, houses 222 hotel rooms in floors 1-17; 287 residences on floors 18-49; and private estates including two 2-storey penthouses on floors 50-66. These comprise 873,000 square feet of development. Eight levels of underground basement are required to provide parking and other amenities, the lower four extending into the shale bedrock."

Jan 1, 2015

By Dr Karsten Galipp, Kai-Julian I. Hendler, Prof. Manuel G. Pinheiro, Dr Peter J. Bourne-Webb

With a share of approximately 11% of global greenhouse gas emissions, the construction industry contributes significantly towards climate change. This is why construction projects should not only be assessed on costs and technical solutions, but also on their carbon emissions. Life Cycle Assessment (LCA) is a tool which can quantify the environmental impacts of a construction project over its entire lifetime. The objective of this study was to determine the carbon footprint of three types of quay wall structures, namely sheet pile combi-walls, open piled decks and caissons using an LCA approach. Each of these quay walls were studied under the same boundary conditions, such as design life, ground conditions, dimensions, location and so on. The analysis showed that the sheet pile wall has the lowest carbon footprint whereas the open piled structure has the highest. Furthermore, it could be shown that the largest share of greenhouse gases (approximately 80%) is emitted during the production of construction materials. The transportation of materials and construction activities each contributed under 12% to total emissions. The sensitivity analysis showed that with innovative approaches, such as adapting the concrete mix design, the carbon footprint could be reduced by 26% to 40%.

May 1, 2022

By Michael D. Justason

"In January 2009, long-time competitors, Anchor Shoring & Caissons Ltd. of Toronto and Bermingham Foundation Solutions of Hamilton, joined forces to tackle one of the Greater Toronto area’s largest deep foundation projects: the West Toronto Diamond Rail Grade Separation. The two companies formed the “West Diamond JV” and succeeded in winning the contract from the Canadian National Railways. This deep foundations work was the first and most significant part of the $300-million-plus rail grade separation project. A big part of the job turned out to be dealing with local government regulations and citizens’ concerns with noise and vibration.The project is approximately 10 km (6 mi) northwest of downtown Toronto in an area of mixed-zoning including light industrial, commercial and residential buildings. The area is commonly called the “The Junction,” because of the heavy rail- traffic. The “West Toronto Diamond” refers more specifically to the railway junction where the North-South tracks of Canadian National (CN) Railway meet at a level crossing with the East-West tracks of the Canadian Pacific (CP) Railway. The goal for this part of the project was to convert the West Toronto Diamond into a grade-separated junction by depressing the CN lines under the CP lines, thus allowing commuter rail carrier, called GO Transit, intercity carrier VIA Rail, and CN freight trains to pass through the new underpass.Dawn Tattle, president of Anchor Shoring & Caissons says, “not only is the site in a densely populated area adjacent to homes and businesses, the crews worked adjacent to active rail lines with numerous trains passing daily. During the 7-hour working day, approximately 60 trains passed through the site in very close proximity to working crews.” Safety was paramount. While trains were passing through the site, it was a railroad requirement that all equipment and men stop working. In addition, at those times, all personnel were required to stay 6 m (20 ft) from the tracks and were required to face the tracks. For the faster commuter trains, this work interruption could last as little as 2-3 minutes, while interruptions caused by the slower freight trains could last as long as 25 minutes. The most disruption to the site occurred during the morning commute between 7 to 9 a.m., so work did not really get underway until after that time. Once work finally commenced the race was on to finish as much as possible before the afternoon commute – hence the shortened work day. The amount of disruption caused by the trains was a big unknown faced by the JV going into the project, but crews adapted quickly to the very unusual work environment"

Jan 1, 2012

By Richard Brink, Eric M. Klein, Kenneth B. Andromalos

"A portion of the roof for a 129 x 144-inch, nearly 100-year-old sewer outfall in the City of Baltimore had deteriorated to the point that it resulted in the development of a large sinkhole in a residential neighborhood. A subsequent video inspection of the sewer outfall indicated that there was a hole in the sewer outfall, and it would need to be repaired . After initial backfilling of the sinkhole and repairs to the water service lines, a conventional wood shoring system was used to support the excavation and expose the Main Outfall Sewer to inspect and repair it. This excavation was unsuccessful because of loose sandy soils and high groundwater conditions. An innovative use of a steel reinforced jet grout excavation support system was ultimately used to underpin an adjacent 20-inch water main and other nearby utilities, and provide access to the top of the Main Outfall Sewer some 22 feet below the street surface to facilitate inspection and repair of the sewer. This excavation support system was also successfully utilized in the final repair of the sewer roof by serving as a buttress for the new roof system.1.0 IntroductionThe project site is located in a residential neighborhood with brick masonry row houses situated on the south side of Chase Street and a brick masonry church on the north side of the street. Figure 1 illustrates the location of the site. The City right of way is 65 feet wide, and the street is 40 feet curb to curb. The centerline of the Main Outfall Sewer runs parallel to and a few feet south from the centerline of the street. Other utilities running parallel to the street include a cast iron 20-inch water line built about 1910, a 24-inch terra cotta storm drain, a 6-inch terra cotta sanitary sewer, a 4-inch cast iron gas line and a 40-inch electrical duct. Cross utilities included a 4-inch gas line and several smaller water and gas service lines to the church and row houses. One gas line that was not shown in the City's GIS database was exposed during the excavation."

Jan 1, 2005