Search Documents

By K. O. J. Sidwell

STRATMAT LIMITED, through its subsidiary, the Strategic Manganese Corporation, controls two adjoining iron-manganese properties five miles west of Woodstock, New Brunswick. One is a staked property of 77 claims traversed by one trunk highway, several secondary roads, and a branch line of the Canadian National railway. The other property, a 20-square-mile Concession immediately to the north-east, is also traversed by an excellent network of roads. Both proper-ties are situated in gently rolling farmland. The deposits were discovered in 1836 by Dr. C. T. Jackson. The first attempt to exploit them was made in 1848 when a blast furnace was erected with a capacity of 7 tons per day. The ore was mined by a series of deep trenches that followed the folds of the enclosing slates. In the late years of operation, bog iron ore from Burton and Maugerville, in Sunbury county, was used in conjunction with the Wood-stock ore. An additional 5-ton furnace was erected in 1863 and mining was carried on intermittently until 1884. No further extensive work was done until 1953. During the period of activity, approximately 70,-000 tons of ore are said to have been smelted ( 1). During these earl y operations the Iron Ore Hill and Moody Hill deposits were partially opened, with the ?bulk of the furnace feed being mined from the Iron Ore Hill workings. The low tenor and apparently limited extent of the deposits, the high. ?content of phosphorus, and the increasing scarcity of fuel, were the chief factors that brought the enterprise to an end.

Jan 1, 1957

By M. Seyed Ahmadi

This study investigates the role of nitrogen gas injection in the dissolution rate of Si into liquid Al. A unique revolving liquid metal tank was used, with a capacity of 50 kg of liquid Al. Experiments without gas injection have shown that the dissolution of Si increases as the bath superheat and the tangential velocity of the liquid Al increase. When injecting nitrogen gas at flow rates between 0-5 lit/min in the vicinity of the solid Si, results so far clearly show greater dissolution. In addition, results on the role of the gas flow rate relative to the position of the nozzle are presented and analyzed.

Jan 1, 2011

By L. A. Wrigglesworth, A. S. Dadson

The orebodies of the Giant Yellow-knife mine occur in zones of schist, in an assemblage of typical Precambrian greenstones which form part of the Yellowknife Greenstone Belt. One of the most interesting problems at the mine concerns the fold-like attitudes assumed by the schist zones. The internal structure of the zones and orebodies provides much evidence of folding. A logical conclusion would be that the zones represent a single horizon which has been folded and drag-folded in the ordinary course of mountain building. However, surface mapping, and correlation of certain marker horizons, in underground work, indicate a homo-clinal succession of steeply dipping flows. If this concept of the geology is correct, the zones must cross-cut the regional strike at a small angle and, in the over-all aspect, the regional dip at a large angle. A mechanical interpretation of the zone structure is presented as a suggestion for the present until new evidence is found.

Jan 1, 1959

By Norman B. Davis

THE ceramic group of industries is comprised of those engaged in the manufacture of cement, glass, artificial abrasives, whiteware, including earthenware, stoneware, porcelain tableware, porcelain sanitary ware, electrical porcelain, floor and wall tile, porcelain enamel on metals, refractories of all kinds, sewer-pipe and structural clay products, such as terra cotta, brick, and hollow tile. The various sub-divisions of the industry produce a wide range of articles on which we depend for our creature comforts from day to day, perhaps to a greater extent than we generally realize. The industry, in turn, depends on a great number of minerals, and chemical products derived from minerals, and it is the object of this brief paper to present a list of these with notes indicating the particular applications. In order to bring home the importance of the industry to your daily life, stop and consider the many things around you accepted as a matter of course. Cement provides the smooth surfaces of many of our highways, city streets, and sidewalks. It enters into nearly all types of construction, alone or in combination with other clay products. Glass we hardly appreciate because we can see through it so easily, but it is there to serve us in windows, doors, and other light-transmitting structures. Glass is the universal means of transporting liquids and beverages, our beverages are usually served in it, and, with the recent development in fine spun glass textiles, there is a possibility of glass clothing in the future. Chinaware, a general term for table dishes, may be earthenware (not vitrified), semi-porcelain, or bone china, but it is before us three or more times a day ?and we seldom think of the minerals that have made these products possible. Floor tile, wall tile, and other ceramic specialties for interior and exterior use and decoration please the eye and provide sanitary surroundings.

Jan 1, 1938

By Lawrence Bragg

WE associate metals with hardness, toughness, and strength. But a curious paradox lies at the root of the valuable mechanical proper-ties of the metallic state: in order to be strong, a metal must be weak. This paradox, and the equally surprising fact that, in a sense, metals are not true solids at all, are among the topics here discussed by Sir Lawrence Bragg. (1) WHAT METALS MEAN TO US We employ various materials to build or fabricate the many objects we use in everyday life, choosing those whose properties are most suitable for the purpose which the object has to serve. Certain of these materials have been used from the earliest times, such as stone, wood, leather, and animal or vegetable fibres, each with its own peculiar valuable properties. Stone resists crushing and is very durable and permanent, as indeed it must be, since it has so long resisted change as a part of-the earth's crust. It is there-fore ideal for walls and buildings, and very early in his history man discovered how to make artificial stones by burning clay, with the advantage that they could be given any desired shape, and made into bricks or given elaborate forms as pottery. Wood is strong and tough and light, it resists tension as well as compression, and is nor brittle like stone. It forms beams and furniture and parts of tools or weapons. Leather is tough but at the same time iris flexible; it is ideal as straps or sheers. Vegetable fibres such as linen or cotton, and animal fibres such as wool and silk, owe their value to their flexibility and strength in resisting extension. They can be spun into yarn or rope, and woven into cloth. The technological age in which we are now living is replacing the natural products used by early man by a series of artificial products, but it is remarkable to see how in nearly every case we are copying Nature's materials. The wide use of concrete represents a developed art of making artificial stone. Artificial fibres such as rayon or ?nylon replace cotton, wool, and flax. Plastics are coming very much to the fore; they correspond to early man's use of horn, another substance with peculiar properties of roughness in all directions without the 'grain' of wood. For the most part we are following in the footsteps of our remote ancestors, though we can make for ourselves what they had to cull from wood and field. There are exceptions; for instance, we have discovered comparatively recently the number of uses to which natural rubber can be put, and are now making it artificially. This is a really new discovery; our ancestors had nothing with such remarkable powers of elastic stretching without breaking, and resistance to being abraded.

Jan 1, 1943

By G. A. Vissac

METHODS of coal preparation have been greatly developed and improved during the past few years. Under the pressing competition from substitutes that have been displacing coal as a source of heat or power, the coal industry has been able, in many cases, not only to hold its own but to regain much of the lost ground, by offering better products of a higher value. The purpose of this paper is to present, in a brief and simple form, the principles of the latest methods and machinery used in coal preparation, in order to enable the coal operator t0 select methods and equipment capable of solving his own problems in the most efficient and economical way. The paper will deal, in the main, .with coal cleaning. It must be emphasized, however, that a complete coal preparation study covers many other operations, such as handling, screening, de-dusting, dust-proofing, and ash-conditioning. Handling Coal From the producing face to the railway car, coal must be handled with great care, t0 prevent degradation, because the coarser sizes are not only easier to clean than fines but, for our markets, they are often the more valuable. Generally speaking, such care is less important or is unnecessary in the Old Country, where conditions are different. The best way to minimize breakage is to avoid gravity methods in coal transportation. All chutes in a preparation plant should be shaken mechanically, and cleaning processes requiring large surge bins must be avoided. De-Dusting De-dusting of coal is accomplished by the use of vibrating screens, fans, or classifiers, or by a combination of these. Fines below 1/32-in. (or coarser than this, with some coals) can very seldom be cleaned efficiently. Common practice is to discard them immediately, if the moisture content of the coal allows this to be done. Otherwise, they are liable to give unnecessary trouble, either in the form of dust or sludge, which are difficult to collect or to settle. Flotation is the only process which will effectively clean fines.

Jan 1, 1937

By A. Y. Senchenko, S. G. Rybkin, A. V. Aksenov

In gravity processing of gold-containing ore the target produced concentrate which is high gold grade primary concentrate contains a significant amount of cassiterite (SnO2). The plant attempts aiming at concentrate processing using a standard pyrometallurgical technology did not provide any positive results. The present paper is dedicated to development and testing of improved technology for pyrometallurgical processing of rich gold primary concentrate with high cassiterite content. According to material composition study primary concentrates produced at the plant contained 1.5–2.0% Au, 0.1–0.3% Ag, 55–65% SnO2, 20–25% Fe2O3, and 10–15% Fe3O4. The developed technology included alkaline nodulizing of primary concentrate mixed with sodium hydroxide and carbonate at 350–650°? with cake production. In blend nodulizing stannum and iron passed into sodium stannate (Na2SnO3) and sodium ferrate (NaFeO2) respectively. The blend of cake and fluxing agents was smelted at 1,150–1,200°? resulting in dore gold and slag production. Sodium stannate with 360°? melting point is well dissolved in slag system Na2OSiO2- B2O3-CaO. During plant tests 18.5 kg of high gold grade primary concentrate were processed, 1350 g of dore gold and 75 kg of slag were produced. Dore gold contained 16.5% Au, 0.95% Ag, 78.0% Sn, 3.1% Fe. Slag contained 12.4 g/t Au, 6.7 g/t Ag, 9.8% Sn, and 5.6% Fe. Gold recovery to target alloy was equal to 99.58 %, 87.8% of Sn passed into slag. This new technology was accepted for application at the plant.

Jan 1, 2016

By Richard P. Curtin, John M. Goris, Lewis A. Martin

Cable bolt supports are being recognized as an effective ground control system in under-ground coal mines in North America, and their use has increased considerably during the past few years. The U.S. Bureau of Mines personnel are conducting both laboratory and field tests to evaluate the performance of these supports under a variety of conditions and to establish realistic design guidelines. This paper describes efforts to evaluate the capability of cable bolts to resist the high shear forces often present in longwall operations. Shear tests were conducted on pairs of 0.025 m3 (0.88 cu. ft) concrete blocks having joint surfaces ranging from rough to smooth. Tests were conducted on blocks both with and without reinforcement with 15.2 mm (0.6 in.) diameter steel cables. During each shear test, the loads and displacements along the normal and shear axes, as well as loads on the cable, were monitored. Cableloads were determined using strain gauges attached to the outside surfaces of the barrel-and-wedge anchors used for pretensioning the cables. Test results show that a cable bolt placed across a joint more than doubled shear resistance of shear blocks having both smooth and rough joints.

Jan 1, 1996

By D. Gorc, T. M. Fraser, Z. T. Nikic, R. Pesalj

"Mount Polley is an alkalic porphyry copper-gold deposit of Lower Jurassic age within the Quesnel terrane in south-central British Columbia. The silica-saturated Mount Polley intmsive complex is assumed to be coeval with volcanic rocks of similar composition in the Nicola Group in which it was emplaced. Other intmsions and some of the volcanic rocks in the Mount Polley area are silicaundersaturated and contain feldspathoids.The Mount Polley deposit is characterized by multiple intrusions that vary from diorite to crowded plagioclase porphyry to monzonite. Intmsion breccias are associated with some of the intmsive phases. Abundant hydrothermal breccias occur on the margins and above plagioclase porphyry intmsions. These breccias provide the main host for mineralization and are associated with the highest concentrations of copper and gold. The breccias are subdivided into four distinct types based on the dominant hydrothermal mineral in the matrix. Actinolite breccia is developed in an elongate zone within the core of the Central zone and grades laterally and vertically into biotite breccia to the southeast. Magnetite breccia is irregularly distributed and is relatively sparse throughout the deposit and albite breccia is dominant in the West zone. Pervasive and vein-related alteration correlates with the breccia types. The core of the hydrothermal system at Mount Polley is subdivided into three zones: actinolite, biotite and K-feldspar-albite. The margins of the core zone are overprinted by a discontinuous zone of calc-silicate minerals. This intermediate zone passes outward into propylitic alteration. Mineralization is most prominent within hydrothermal breccias and is generally present as disseminations, blebs within the matrix and abundant veins. Mineralization is associated with a chalcopyrite-magnetite-bornite assemblage in the core of the deposit passing out into magnetite-pyrite-chalcopyrite. Relatively constant copper to gold ratios suggest that both metals were precipitated under similar conditions.Hydrothermal breccias are genetically related to the emplacement of the crowded plagioclase porphyry melt. Crystallization of the melt was probably accompanied by volatile/aqueous exsolution, forming a water saturated carapace. Decompression of the chamber in response to magma withdrawal, fracture propagation and possible fault movement allowed hydrothermal brecciation to occur at the apex and margins of the intmsion. Alteration and mineralization appears to have been controlled by fluids migrating away from the plagioclase porphyry."

Jan 1, 1995

By Rodgers Peale

The Waite mine, as it is locally termed, is situated in the Rouyn district, in the townships of Duprat and Dufresnoy, Quebec, and lies about 340 miles north of Toronto. Due to the impetus given prospecting in the Rouyn district by the discovery, some years ago, of copper-gold ore on the Horne claims, many exploration parties were put into the field. Early in 1925, J. H. C. Waite, C. H. Ackerman, and T. Montgomery staked the claims which now comprise the mine beating their names. Trenching and diamond drilling soon disclosed an ore-body of commercial size and grade, and by the end of 1928 a shaft had been sunk 300 feet and the mine was producing 150 tons of direct-smelting copper ore a day. In the summer of 1925, Dr. H. C. Cooke, of the Geological Survey, made a reconnaissance survey of the property (1), and since that time work of the same nature has been done by several others. MacGregor has published some interesting data on the Amulet mine (2). Using as a background a summer's work on the Horne claims at Noranda, the writer spent the summer of 1929 at the Waite.

Jan 1, 1931

By R. J. R. Welwood, F. J. Grebenc

"Brunswick Mining and Smelting Corporation Ltd. (controlled by Noranda Mines Limited) operates two lead-zinccopper- silver mines approximately 20 miles inland from Bathurst, N.B. The principal No. 12 orebody is mined by underground methods; the second, the No. 6 orebody (6 miles away), is recovered by open-pit mining. No. 12 underground operations ar•e in two parallel massive sulphide orebodies about 400 ft apart, dipping at 75 to 80 degrees and plunging almost vertically. The initial mining phase involved longhole open stoping from the 1550 level to the crown pillar, with main levels at 150-ft intervals and sub-levels between at 75 ft. Stope dimensions average 120 ft long, 100 ft wide and 400 ft high, with alternate rib pillars as well as sill and crown pillars. Initially, ore was transferred through scram drifts below each stope by means of 125-hp electric slushers and 72-in. folding scrapers, being delivered to gravity ore-pass collection •systems feeding a primary jaw crusher below. Later, track and trackless drawpoints were utilized below most longhole open stopes and pillars. Rib pillars were recovered by longhole methods, with large blasts into a central slot and undercut, after adjacent stopes had been filled. Waste-rock stripping from No. 6 open pit has been supplied to No. 12 stopes as backfill, by means of gravityfill raises.In 1968, the decision was made to mine the remaining ore zones by mechanized cut-and-fill methods, utilizing Load-Haul-Dump equipment. Currently, approximately 60 per cent of No. 12 mine production comes from mechanized cut-and-fill mining. As before, backfill is supplied from No. 6 open pit stripping waste rock, which has been crushed to minus 6 in. The ultimate objective is to supply virtually all production requirements by mechanized cut-and-fill techniques. The No. 6 open pit, which commenced production in 1966, covers an area of 1,500 by 1,200 ft, equivalent to 41 acres approximately. Ramp roads are graded at 8.5 per cent. Each mining bench is 36 ft high and the ultimate pit will consist of 14 benches for a final pit depth of 504 ft. Present depth is 180 ft."

Jan 1, 1971

By R. Fukuzawa

"The objective of this research is to evaluate the magnitude of carbon prices required to drive process development and innovation for the global nickel industry in a direction that tackles the multifaceted sustainability challenges that the industry faces, including air pollution reduction and greenhouse gas abatement. The results suggest that the currently considered carbon prices are not sufficient to drive innovations in processing methods or upstream pollution prevention. The co-benefits of climate change mitigation and pollution prevention cannot be readily realized under climate change policy alone. Increased coordination between climate change policy and performance-based environmental legislation is necessary. INTRODUCTIONNickel is an important metal in our modern society as it is used in stainless steel, alloys, electroplating and rechargeable batteries, all of which are integral to our economic growth and development (Eckelman, 2010).However, nickel production is energy intensive and therefore susceptible to emerging climate change policies, which may lead to production curtailment and/or increased unit costs of production unless changes in efficiency or energy sources are made (Mudd, 2010). The industry is faced with multi-faceted constraints: future technology must not only deal with metallurgical, financial and environmental constraints but also promote low energy and low carbon practices. This presents a challenge for this industry where technology innovation, development and commercialization are often lengthy, risky and costly processes (Imrie, 2006).Climate change is one of the many challenges faced by our society. Others include other pollution to air, water and land, resources shortage and economic development. From a policy perspective, it is important to balance multiple and often competing needs in an integrated manner. It would require some levels of trade-off in order to maximize the overall effectiveness but also to ensure that one policy does not undermine other policy objectives.The aims of this study are to evaluate how developments in climate change policy would affect the nickel industry in the context of existing environmental regulations and how the industry could respond under these constraints."

Jan 1, 2012

By Bertrand Robinson

Great advances have been made in rubber-lined pumps for the pumping of mill pulps. The Canadian Allis Chalmers alone report ov.er 300 such pumps put into service during the past four years. Pumps in which both the casing and the impeller are rubber covered have proved most economical in handling the usual run of mill pulps, effecting large savings in power, maintenance, and shutdown costs. For the handling of pulps containing comparatively large, sharper edged /articles, rubber-lined casings with hard iron impellers have been developed by the pumping departments of Hollinger and Noranda. These rubber-iron combination pumps show an appreciable reduction in overall pumping costs as compared with the all-rubber and the all-iron pumps. The power efficiency is lower in rubber-iron than in all-rubber pumps but higher than in the all-iron pumps, with lower replacement costs due to the cheap iron impellers used. Where continuous operation is essential, however, and duplication of units to take care of shutdown time for replacement of parts is not within the expenditure budget of the company, all-rubber pumps are being used t0 a greater extent. As in all items pertaining to milling operations, the economics of the situation must be studied as closely as the technical details, to arrive at the most advisable practice.

Jan 1, 1939

By W. B. Evans, D. P. Taylor

"ANFO has two major disadvantages as an explosive low density and no water resistance. ANFO can be blended with more dense, water-resistant explosives to form ""Heavy ANFO"". The use of emulsion or slurry explosives as a matrix is an attempt to correct deficiencies on the basic ANFO while maintaining cost effectiveness.This paper will deal with four main topics.1. Product description, general properties, strengths and weaknesses.2. Technology of ""Heavy ANFO"" , the emulsion matrix concept and the range of products.3. Relative performance and economics in various rock types.4: Current status in Canada and worldwide, and the expectations for future use.IntroductionANFO has been in use for roughly three decades and remains the explosive of choice where conditions are suitable. ANFO has not become the universal explosive - despite its undoubted superiority in cost effectiveness - because it has serious flaws as an explosive. The most serious of these flaws are the low density and absence of water resistance in ANFO. Low density implies a low concentration of explosive energy in a borehole. The amount of energy available can be increased by. adding an energetic material, generally aluminum, or by drilling more holes. Both solutions add considerably to the over-all costs. The absence of water resistance in ANFO is inherent and can only be overcome by changing the fundamental nature of the product. The history of research in the explosives industry since the advent of ANFO is mainly the story of the various attempts to overcome one or both of ANFO's shortcomings.Many technologies and products have been developed to compete against ANFO, among them slurries, emulsion s and the so-called Dense ANFOs (ANFO with an extra nitroalkane liquid sensitizer). None of them was cost-competitive with ANFO so their market penetration has been limited to wet holes or specialized applications. The exception to this result is Heavy ANFO. The aim here was to have the best of both worlds, the high density and water resistance of emulsions or slurries plus the low cost of ANFO. The concept is very simple. ANFO is about 50 % air, roughly 30% in the prills and 700,10 between the prills . The air in the prills provides the necessary sensitivity but the air between them is waste volume. If one fills this volume with a high density, waterproof product, the resultant mix will be denser and more water resistant than ANFO and with very little added cost. This basic concept was invented by B. Clay in the 1970s and is covered by Canadian Patent No. 1 115 959. The water resistance and/or density of the mix can be tailored by changing the emulsion level. Because Heavy ANFO is relatively inexpensive while providing good in-hole densities and water resistance, it can compete successfully against all other bulk products. It competes against ANFO and Al / ANFO by allowing pattern expansion and reducing over-all costs while it competes against emulsions and slurries on price."

Jan 1, 1987

By G. H. Blackwell, N. I. Norrish

"At most operating mines, geostatistical are reserve estimation methods have been implemented by head office or consulting groups . With recent advances in small computer technology it is now possible for a remotely-located mine department to independently implement a geostatistical package.This paper describes the evolution of geostatistical routines to calculate the mineral inventory for porphyry type copper/ molybdenum or similar are bodies. The problems encountered in down sizing the geostatistical routines to run using limited minesite computing facilities are discussed. The high quality of the results, in spite of some compromises to geostatistical theory, is emphasized.The first stage entailed the development of a mineral inventory based on diamond drill data. The difficulties in fitting variogram models to two metals, copper and molybdenum, and the shortcomings of the mineral inventory due to the mixing of lesser quality exploration data with data from more recent diamond drilling are discussed.To improve the ore reserve estimates for short-term planning, a mineral inventory was produced using both the diamond drill and production blast hole drilling data. This inventory, when compared to actual grades, was found to be quite satisfactory for short-term planning. The inventory also provided a reliable data base for long range pit design and financial planning. By regularly updating the mineral inventory, many of the uncertainties of mining a low-grade orebody were minimizedIntroductionThe comparatively low grades of many Canadian mineral deposit s, the escalation of mine operating costs, and the volatility of metal prices in recent years, has required improvements to both short- and long-term mine planning.One of the prerequisites to improved planning systems is the need for accurate grade prediction. This paper describes the on-site implementation of geostatistical techniques for grade estimation of a porphyry I vein type copper/molybdenum ore body ."

Jan 1, 1987

By A. van As, J. McGaughey, M. J. Mol, R. Tosen

Geotechnical monitoring is a key element of the successful management of a block cave mine. The interrelationships between production and various monitoring datasets are often not realized due to a lack of data integration and appropriate 3D visualization. Timely delivery of information to ensure best cave management practices is only possible with an integrated cave management system. At Rio Tinto, a state-of-the-art cave management system (CaveCAD) has been designed and developed in cooperation with Mira Geoscience to integrate and analyze vast datasets and report this as instructive information regarding the current \u201cstatus\u201d of the cave.

Jan 1, 2014

By S. S. Al-Thyabat, A. M. Ghrair

"Printed circuit board (PCB) is the main part of any electric or electronic device, providing mechanical support and electric connection for the board eclectic components such as capacitors, resistors, diodes etc. PCB consists of non-conductive substrate overlaid with one or more layers of copper sheets. They also contain appreciable amounts of base metals (copper, nickel, tine, and aluminum) and precious metals (gold, silver, and rare earth elements (REE)) which end up in the landfill at the PCB end-of-life.PCB recycling E-waste in general is a profitable business; many valuable raw materials, precious and base metals, can be extracted with high purity. Approximately, one metric tonne of PCBs may contain 80-1500 g of gold and 160–210 kg of copper. The precious metals recovered from PCBs occur at concentrations higher than commercially mined minerals. Also PCB recycling is very important to our environment since many heavy metals (e.g. lead) may be leached from the landfills to the underground reservoirs. In Jordan, however, the work conducted on E-waste and PCB recycling in particular is limited; currently most of the E-waste is either exported or dumped in the landfill.In this work, a combination of physical (magnetic separation), physicochemical (flotation), and chemical methods (leaching) were used to compare metals concentrations in leach liquors produced from a concentrates resulted from a combination of these methods. It was found the leach liquor of the magnetic fraction of the PCB coarse size gave the highest concentration of Fe, Al, and Ni while concentration of Cu was higher in leach liquor of nonmagnetic sink fraction. On the other hand, metals concentration almost similar for both sink and float of the fine size fractions, indicating even distribution of metals concentrations in the fine size fractions."

Jan 1, 2016

By W. M. Goodwin

The gold district of northwestern Quebec, though it has attracted such widespread attention during the past year, is still in the prospect stage throughout, and one must preface any remarks about it with the plain statement that its capacity to produce gold commercially is still subject to proof. However, this proof may be forthcoming any day, and from widely separated localities. Consequently it is of interest to note some of the features of the region and of the prospects now being developed. First I shall note the relation of this mining development to the province of Quebec and to the Dominion; then will follow a brief resume of the known geological facts; and finally I shall describe briefly some of the more advanced prospects developed during the past twelve-month. Those that have followed closely the fortunes of the new gold-field will find little that is new in what follows, but it may serve a useful purpose for others by bringing together scattered items of information and presenting them as a whole. GOLD MINING AND AGRICULTURE First let us consider the gold belt in its relation to the province of Quebec. Apart from the world-renowned asbestos camp south of the St. Lawrence, it is the only mineral development of major importance the province has experienced. It is the first important development in the province's vast area of Precambrian rocks, most of which remains as yet totally unexplored and unprospected. The relative importance of this first mining camp in northern Quebec cannot as yet be gauged, but it is bound to stimulate an active interest in the other mineral-bearing areas now known to exist, and in the vast unexplored spaces.

Jan 1, 1924

By S. S. Dimov, B. R. Hare

This paper describes two micro-beam analytical techniques(Dynamic SIMS and TOF-SIMS) which have become an intricate part of a comprehensive analytical approach for precious metal (PM) ore characterization and process mineralogy or deportment studies. The value of the D-SIMS technique is its capacity for accurate analysis in the sub ppm range along with the ability to produce high resolution elemental maps. The TOF-SIMS is significant for speciating and quantifying preg-robbed Au on the surface of carbonaceous material. In combination with traditional assays, the two techniques can provide invaluable information regarding the distribution of PMs within an ore along with providing insight into potential sources of PM loss in processing or where losses have occurred in process streams.

Jan 1, 2011

Pilot plants for pressure hydrometallurgy represent special design and project execution challenges unique to the industry and to the pilot- and demonstration-scale. Pilot plant projects have different objectives and shorter timescales than commercial plant projects. Design considerations and strategies, and project execution methods that meet the special needs of pilot plant projects, are discussed. Specific guidance is given for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical process equipment, and for the selection of materials of construction for pilot-scale equipment. The balance between the need for process similarity with future commercial operations and the realities of pilot-scale equipment is also discussed.

Jan 1, 2004