Search Documents

During the period 1981 - 1991, Esso Australia and their Joint Venture partners have discovered about 180 MB of liquids (crude and condensate), 60 MB natural gas liquids and 800 - 1000 GCF of gas. A total of 48 wildcat wells were drilled including 12 new pool discoveries drilled from platform facilities. Significant discoveries include the West Tuna, Kipper, Blackback and Terakihi fields. These four discoveries, contribute to 75 per cent of the total reserves discovered in the last decade and were all high-risk plays. The Kipper discovery, in the pre-Latrobe Golden Beach Group top sealed by volcanics, and the Blackback-Terakihi discoveries, located on the present day continental slope in water depths ranging from 300-700 metres are both the result of successful drilling outside the traditional exploration bounds for the basin. During the last decade, Esso and its partners have spent about A$400M on wildcat exploration activity. The exploration success rate, excluding platform based drilling, has been 50 per cent for wildcat wells. On a technical front, the last decade has heralded substantial improvements in seismic data quality. Peak frequency content in seismic data at the Latrobe Group target levels is now double that of the early 1980s. Significant advances have also been made in our understanding of sequence stratigraphy, geochemistry and geohistory of the basin.

Jan 1, 1992

By Prakash AJ, Singh PK, Dhar BB

Safety and stability of underground mine openings, coal pillars and water dams in the near vicinity of operating surface mines are endangered from excessive blast induced vibrations. This paper deals with the investigations carried out in four coal mines. Simultaneous measurements at equal distances from the source indicated higher level of vibration on the surface than those produced in the underground workings. The values of peak particle velocity (PPV) measured on coal pillars, body of water dam were lower than those measured on roof and junctions of the roadways. The parting of coal (3-4.5 m) between two sections vibrated with higher PPV compared to the roof of top section and floor of bottom section. In one case the influence of total charge fired in a round was significant in generation of vibration compared to the maximum charge/delay where monitoring was done vertically below the source.

Jan 1, 1995

By Erceg MM

The Waft River gold deposit is hosted by low grade metasediments which have been intruded by a dacite/andesite porphyry complex. Wafi River is classified as a high sulphur, epithermal type gold deposit having: a high sulphur content, a close association with calc-alkalic igneous rocks, zoned advanced argillic and argillic alteration, and enargite group minerals. Gold occurs as minute inclusions in pyrite and pyrrhotite within intermediate dickite/kaohnite - interlayered illitic clay alteration zones. Central leached silicic, alunite and pyrophyllite zones and peripheral chloritic zones are low in gold. The gold mineralisation at Wafi is interpreted to have been predominantly caused by mixing of hot upwelling acidic magmatic mineralised fluids with cool, neutral meteoric/hydrothermal fluids within permeable sediments. Locallised high grade breccia zones are encountered within the porphyry. An initial resource in excess of I million ounces Au has been defined.

Jan 1, 1990

By Longworth C. R

Competing requirements for land usage sometimes make the correct all- ocation difficult. The decision can be complicated by many factors such as local resident pressure, previous government decisions, economic pres- sures and the duration or permanency of the competing land usages. This problem often confronts the extractive industries with consequent delays in granting leases and some- times considerable local dissension. A proposal to extend the high grade silica sand quarry of the Wamberal Sand Company Pty. Limited is a microcosm of these competing requirements. The sand quarry is located on the New South Wales central coast. It is an open pit operation on a near beach deposit of silica sand suitable for flint glass manufacture.

Jan 1, 1976

By C Itotoh, K O’Halloran, L Karlson

Global methods used to explore for minerals have progressed relatively slowly since the development of the first diamond core drill in 1863. Since then, key developments such as wireline geophysics (1920s), the tricone drill bit (1930s) and aeromagnetic surveys (1940s) all occurred in response to global events. In this project, BHP’s WAIO Geoscience operations team hypothesise that a global movement towards a greener future as well as an increasing intolerance for safety events will drive another step change in exploration methods. We have leveraged our relationships with exploration contractor partners and industry leaders to develop a realistic vision for 2033 and beyond, where drill rigs, earthworks and geophysical units are operated and maintained remotely; emissions of dust and waste are eliminated; hazardous energy sources are controlled; procurement is based on sustainability rather than cost and carbon emissions are tracked with the same rigour as production metrics. We have combined these visions into a series of graphical illustrations with the aim of inspiring ourselves, our vendors and our peers to collaborate further on producing a step change in our industry.

Sep 18, 2023

By S Padekar, C Tapia, D Likhachev, S Harlikar, D Sapkale

In the quest to access valuable critical minerals, humankind is expanding the frontier into extreme environments like space and deep-sea mining. These ambitious enterprises involve considerable costs and lengthy development cycles to ensure the robustness of mining systems in the face of the harshest conditions and unforeseen challenges. Unfortunately, obtaining information from these unexplored territories is complicated. Data is often scarce, incomplete or impossible to obtain until equipment is deployed, leaving engineers facing many uncertainties throughout the design, testing, production and preparation of such missions. Despite these challenges, these extreme environments operate under consistent physical and chemical principles that can be faithfully digitally replicated. However, unexplored areas and dynamic systems like weather and geology continue to carry uncertainties. While eliminating uncertainties remains elusive, Digital Twins offers a means of robust risk management tool. These virtual replicas can excel in simulating extreme conditions and unexpected events, helping optimise and validate mining system designs tailored for such hostile environments. This study takes inspiration from the Mars Science Laboratory (MSL) Curiosity Rover’s wheel damage rate to develop a Multiphysics Modelling and Virtual Motion Simulation (MMVMS) system. Using advanced Generative Design, this MMVMS system refines the MSL’s design, simulates component and system performance, and assesses the risk of premature damage while operating on Mars. Additionally, MMVMS integrates cutting-edge CAD design technologies from aerospace and manufacturing to realistically recreate the Martian environment and a detailed representation of MSL, allowing mobility verification and validation simulation to test different components in terms of materials, design, weight, power and, therefore, cost. The research highlights the precision of MMVMS in replicating extreme conditions, simulating and evaluating internal and external variables influencing the entire system (Rover) in real-time, and predicting movements, failures, and premature damage. This sophisticated Digital Twin technology, showcased in this research, holds promise not only for space missions but also to be adapted for terrestrial and deep-sea mining operations.

Sep 1, 2024

By R Coleman

The flotation mechanism plays a key role in the flotation process. It is used to provide the contact between solid particles and bubbles and also the energy for these particles and bubbles to attach. The mechanism must therefore provide sufficient mixing to keep the solids in suspension so that they can be transported into the froth and recovered to the concentrate. The design of the mechanism is critical and over the past decade Outotec has developed and optimised a new mechanism design to improve metallurgical and energy performance. The FloatForce® mechanism consists of a rotor and stator arrangement and has been specifically designed to provide sustained mixing at higher air flows and lower power inputs.Over 500 FloatForce® mechanisms have been installed in existing and new operations. This paper outlines the technological aspects of the FloatForce® mechanism and provides metallurgical, operational and energy performance results from a number of flotation circuits in which these have been installed.

Aug 8, 2011

This problem is seen as being central to a number of peripheral problems. Of these, the following are considered to be of major importance: 1. Reserves. Changes in Quality. Depths at which they occur. The effects of catchment and water storage areas. The effects of urban development. 2. Environment and the compat- ibility of mining and preparation of coal. 3. Transportation of Coal. J. tabour.

Jan 1, 1976

By Stokes WPC

The capital requirements to develop a new mining venture are becoming very large; amounts of the order of US$1,000 million are not now unusual among estimates to bring new mining complexes into production. At the same time prevailing political and economic conditions are making it increasingly difficult to determine whether or not a project is likely to be viable. These factors emphasise the need to carry out thorough evaluation studies of all mineral prospects before making major investment. Additionally with the rapidly changing economic climate existing at the present time, it is becoming more and more necessary to carry out reappraisals of existing mines. An important function of both initial evaluations and reappraisals is to provide the operators of the mine with effective mining plans to ensure that the operation will meet its required economic targets. P, p M. tl p b, c v, s c 1 n 1 f r d c e c e u w Modern computers are well equipped to store and manipulate large amounts of data with speed and reliability. Their use in the mining field r is increasing and this trend serves to free f technical staff from much of the time consuming m and error prone hand calculations which were o formerly required in determining reserves and w carrying out all forms of mine planning. r Nevertheless, computers are not a universal

Jan 1, 1980

By C Claassen, R Balusu

Computational fluid dynamics (CFD) models have been developed based upon field data collected from a longwall mine in New South Wales, Australia to study the behaviour of goaf gas flow in both active and sealed goaf areas. A base CFD model was built to represent the goaf situations when the active longwall retreats near the finish-off line. Results from the base model were calibrated and compared against field goaf gas monitoring data. The base model was then used to carry out parametric studies to investigate a number of operational scenarios and their impact on goaf gas behaviour. CFD modelling results indicate that the overall goaf gas flow pattern changes as the operating longwall retreats towards finish-off line. In all cases, oxygen penetration into the active goaf remains high, reaching 15 per cent or higher, even at some 800 m behind the longwall face.The modelling results also indicated that it would be difficult for early detection of an active goaf heating (on the maingate side) based upon CO readings in the return airflow, as the main stream of the gaseous product will be flowing into the sealed deep goafs in adjacent longwall (LW) panels. Monitoring points (such as tube bundles and bag sampling points) should be selected at deep seated seals along the active goaf so that abnormal CO or C2H6 readings can be picked up for early detection and location of potential heating spots; goaf inertisation can be better achieved by injecting inert gas such as nitrogen at deeper points (>200 m) behind the operating longwall; the injection of in-seam drainage methane into the goaf areas will only have a limited impact on goaf inertisation as much of the injected methane will migrate towards deep and higher parts of the goaf due to its buoyancy effect.

Sep 26, 2011

Oxygen is required for the leaching of gold ores in cyanide solutions. The source of this oxygen demand and the effect of dissolved oxygen concentration on the rate of the process are briefly reviewed.A method of measuring the oxygen consumption rate is described and some experimental results reported.Fundamental aeration theory and rating of aerators is summarised to show how this type of experimental work provides the basis for full-scale design of aeration equipment.

Jan 1, 1984

A study was conducted to evaluate the effectiveness of the three types of sample grinders routinely used in the mining industry for the sample preparation of gold ores with particular emphasis placed on testing their capacity to produce a representative assay sample of coarse gold ores. The grinders used in this study are the Labtechnics LM5, the Mixermill 4010 ringmill and the Keegor vertical spindle pulveriser, commonly called a Keegormill. The study was based on the preparation of samples from two sources of known coarse gold ore, the Union Reefs Gold Mine and the Brocks Creek Gold Mine in the Pine Creek region of the Northern Territory of Australia, and a fine gold ore which was from the Macraes Gold Mine in New Zealand. The Union Reefs Mine contains visible coarse gold with 30 per cent to 40 per cent of the gold in the plus 75 μm fraction of milled ore. Discreet particles up to 5 mm have been recorded, Hellsten (1994). Union Reefs Gold Mine recovers 40 per cent of its bullion production through a gravity circuit, Riches (1997). Brocks Creek ore contains visible coarse gold with gravity bullion production fluctuating between 50 per cent and 65 per cent, depending on the mill feed. Average gravity bullion production from the Brocks Creek Mine is 55 per cent, Wilke (1997). The average gold grain size of Macraes Mine ore is 20 μm with 40 per cent of the gold in sub 10 μm particles. No gravity bullion is produced from the Macraes Mine, O'Keefe (1997). The testwork demonstrated conclusively that it is possible to prepare a representative sample for assay, of a coarse gold ore, when a Keegormill is used to pulverise the sample to a nominal 100 μm particle size (90 per cent passing a 100 μm screen by wet sieving). Both the Mixermill and the Labtechnics LM5 failed to prepare a representative sample, even when ground to a nominal 75 μm particle size.

Jan 1, 1998

By Shu DM, Moxon P

Subsidence profiles over longwalls at West Cliff Colliery (WCC) are predicted by three methods, NCB Emperical Method, Salustowicz's Profile Functions and Superposition of Two Critical Profiles. A method of deriving maximum subsidence using local data is also presented. For the first four longwalls, the results are compared with those from the subsidence surveys conducted during and after the extraction of each longwall. Longwall V has not yet been extracted, so the results are for the predicted subsidence profile. Superposition of two critical profiles is carried out in an attempt to check the principle of superposition. In addition, strata movement above the extracted longwalls is discussed.

Jan 1, 1986

The Yanacocha district hosts the largest and most significant acid-sulphate, high-sulphidation deposits in Per· with total production, reserves and resources of over 27 million ounces of gold. Several other smaller high-sulphidation systems are also recognised in the Cajamarca region including La Zanja, Sipßn, Tantahuatay, and San Nicolas. These each have reserves/resources of between 640 000 and 800 000 ounces of gold. Gold deposits in the Yanacocha district are hosted in an extensive volcanic field. Flow domes have intruded precursor pyroclastic rocks and flows that are interpreted as part of an earlier intermediate multi-vent volcanic complex. The larger, contiguous Yanacocha Norte - Sur and Encajon gold deposits are spatially associated with late-stage diatreme breccias. At La Zanja extensive acid-sulphate alteration is associated with the margins of the small San Pedro caldera (6 +4.5 km), nested within the larger, less well-defined La Zanja caldera (19 +24 km). The inner caldera is resurgent with abundant magmatism expressed as several flow dome complexes located on the caldera rim, and shallow level intrusive stocks. Gold mineralisation is associated with a WNW-trending structural corridor that transects the southern margin of the San Pedro caldera. On the eastern side of the La Zanja caldera there are a series of younger andesitic eruptive centres, some associated with acid-sulphate alteration and gold mineralisation. The Sipßn deposit occurs in one such centre with structurally-controlled gold associated with a NE-trending silicified structure developed within a sequence of andesitic tuffs. In conclusion, although a number of high-sulphidation deposits are recognised in northern Per·, their settings and styles of mineralisation are all quite different. Smaller deposits generally have strong and obvious structural controls. In the larger Yanacocha deposits the structural controls are less obvious, and mineralisation is disseminated in porous or strongly fractured and brecciated silica. Erosional levels are probably a significant factor, with disseminated mineralisation at higher levels, and structurally-controlled mineralisation in more deeply eroded deposits.

Jan 1, 1999

By M T. Nguyen, S Vink, M Ziemski

On any given mine site the water system is contingent upon its initial design. Through time the initial design is adjusted by a myriad of water management options in order to improve water system performance or to adapt to a new production capacity or method at the mine site. These options generally do not comprehensively consider energy requirements, so it is unlikely that any given mine water system will be optimised in terms of both water and energy uses. Thus this may simply shift constraints of efficiency of one resource dimension, water, to another, energy. As a result, changes in water systems would cause more energy-related issues to mining companies. For example, the companies would have an increase in operational cost and/or pay more for carbon tax with changes in their water system. Therefore, in order to avoid undesirable and potential unforseen energy and infrastructure issues in a mine life cycle, it is essential to select suitable water management options for a mine considering both water and energy resources simultaneously.Considering water and energy criteria in evaluating water management options consists of net water volume availability, net operational energy demand and net water replacement energy demand. Ideal water management options should be high in water volume availability but low in both operational energy demand and water replacement energy demand. A water option would also be favourable if it has low potential of causing adverse environmental impacts such as lowering groundwater tables due to groundwater withdrawal, or elevating saline constituents in surface waters when reusing brine for dust suppression. However, these environmental impacts are not considered in this analysis.This article presents a graphical method to assess mine water management options, based on these three criteria. The proposed method to assist in screening mine water management options includes two main steps:1. categorise water management options into prioritised groups2. rank the options within each prioritised group.The method is applied to a gold mine and presented in this article as a worked example. CITATION:Nguyen, M T, Vink, S and Ziemski, M, 2013. Selection of mine water management options considering both water and energy impacts, in Proceedings Water in Mining 2013 , pp 29-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

The Cadjebut Mine is located 80 km southeast of Fitzroy Crossing. Cadjebut is owned 58 per cent by BHP Minerals and 42 per cent by Billiton Australia. Cadjebut is a 'Mississippi Valley Type' (MVT) deposit. Minerals present are sphalerite, galena and marcasite in a sedimentary host of dolomite and siltstone. The ore contains few deleterious impurities and no silver. The mill was commissioned in the first half of 1988 at a rate of 320 000 tonnes per annum. An expansion in the latter half of 1989 has since increased production to 550 000 tonnes per annum. The initial geological resource at the commencement of mining was 3.8 million tonnes at 13.5 per cent Zn and 4.4 per cent Pb. There is sufficient ore left to sustain operations to 1995 at a grade of 11.2 per cent Zn and 3.9 per cent Pb. The ore from underground is stockpiled on the surface via a drift conveyor and from the stockpile is fed into a grinding circuit consisting of a SAG and ball mill. Cyclone overflow at a Pgp of 90 pm gravitates to the flotation circuit. Lead and zinc are sequentially floated to produce an 80 per cent Pb grade at 90 per cent recovery and a 61 - 62 per cent Zn grade at 96 per cent recovery. The concentrates are thickened and filtered before being trucked to the port of Wyndham 600 km away. From Wyndham the concentrates are shipped to smelters in Asia, Europe and Australia.

Jan 1, 1992

The reasons for and the methods of inte- gration of the gold treatment plant with the existing nickel concentrator are discussed. The integration was accomplished in three stages commencing in May 1980 and attain- ing current throughput in December 1982. The problems encountered and their solution, including the design and construction of a new tailings dam are also discussed.

Jan 1, 1984

The Acid Drainage Technology Initiative (ADTI) was initiated in 1995 by federal agencies, the National Mining Association (NMA) and the Interstate Mining Compact Commission (IMCC) to identify, evaluate and develop cost-effective and practical acid drainage technologies. In 1999, ADTI was expanded through the addition of the metal mining sector, which is focused on drainage quality issues related to metal mines. ADTI addresses drainage quality issues from abandoned, active, and future coal and metal mines. The guiding principle of ADTI is to build consensus among industry, federal and state regulatory agencies on acid drainage technology development and technology transfer issues. ADTI is focusing its efforts on mine drainage prediction, sampling/monitoring, modelling and avoidance/remediation. ADTI is not a regulatory or policy development program. ADTI includes the Coal Mining Sector (CMS) and the Metal Mining Sector (MMS) under the overall guidance of the ADTI Operations Committee. The Operations Committee consists of representatives from industry, state and federal government and academia. The Coal Mining Sector includes two committees; a prediction committee and an avoidance and remediation committee. The Metal Mining Sector includes steering committee and work groups on prediction, sampling and monitoring, modelling, mitigation, and pit lakes. The Coal Mining Sector has produced two publications on the prediction and prevention of acid drainage. The Metal Mining Sector has workbooks under preparation covering the work group topics. This past winter, the Metal Mining Sector, working with the US Bureau of Land Management, presented a satellite training session on acid drainage. ADTI has evolved in response to changing needs and technologies as evidenced by the addition of the Metal Mining Sector in 1999. The Operations Committee and the members of the Coal and Metal Mining Sectors will guide future direction in response to identified issues.

Jan 1, 2003

By Leahey T. A

The variability of gold mineralization in the Warrego Gold Pod is described by classical statistical techniques using sample distrib- utions and analysis of variance; and by the use of geostatistical variogram analysis to define the spatial variability and anisotropy of the mineralization. Comparison is made between declared mine production from the Nineteen Stope and a series of ore reserve estimates derived by manual, numerical and disjunctive kriging methods.

Jan 1, 1979

British Coal's Selby Complex is the newest producing mine in the United Kingdom. The reasons behind its origins, planning and design are explained. Some detail is given of equipment used, with the emphasis being placed on the unique features of its layout. The entire project has been planned and constructed over many years and the design has consequently changed, principally in response to the geology of the coalfield and improving technology. In spite of many totally unexpected difficulties, the mine, which is not yet in full production, has the highest productivity in the United Kingdom.

Jan 1, 1991