Search Documents

By Ernest F. Burchard

In connection with the work of testing structural materials for the use of the U. S. government at the laboratories of the technologic branch of the U. S. Geological Survey at St. Louis, Mo., from September, 1904, to April, 1909, and since then at Pittsburg, Pa., large quantities of sand, gravel, and crushed stone have been needed from time to time, besides samples of building-stone, clays, and other quarry-products. In many instances it has been necessary to obtain single samples of sand, gravel, or crushed stone in lots of a car-load or more. For obvious reasons all these collections have had to be made by a representative of the Survey. As the work progressed it was found essential that numerous geologic data should be gathered regarding the materials collected, in order that they might be properly classified as to kind of material, source, geologic age, etc., and that they might be rated according to quantity available, accessibility to transportation facilities, approximate costs, suitability for special purposes, etc., and that notes might be taken regarding undeveloped deposits of possible value. Furthermore, it mas desired that the selection of materials for tests should be made broadly, so as to cover, first, the representative types of material, and later, if possible, the typical materials of the more important building-centers in the United States. In order to insure a certain degree of uniformity in this work and economy of effort and expense, it was decided that as much of the sampling as was practicable should be done by a member of the geologic branch, whose regular field-trips could be combined conveniently with those necessary for procuring materials for the laboratory. During parts of the last three years 1 have been engaged in field-work of this sort.

Jan 1, 1911

DESPITE the very small number of engineers who can get away from their tasks to New York, a point so far from the Mid-Continent and Cali-fornia oil fields, where the real important, engineering progress in the industry is being made, the attendance was remarkably good, and it was generally remarked that all the sessions were "snappy," and there was no drag. This was largely because, under instructions from the chairman, very few papers were permitted to be read, and the "high lights" of each paper were pre-sented orally as an introduction to the large and varied discussions, many of which were prepared in advance. The round table discussion on petroleum engineering research problems, conducted by W. E. Wrather, proved a greater success than was anticipated, considering the difficulty in getting many of the men to discuss such problems. There has been no crystallization of opinion heretofore of what are important engineering research problems, as distinguished from pure science problems, and a digest of the discussion will be made available so as to present the results obtained. It is hoped that further round table discussions, as well as committee work, in the meantime summarizing problems appear-ing in papers published the last two to three years, will enable the oil industry to determine intelligently which of the problems are most important for immediate attack. The roundtable discussion on petroleum engineering educational problems, conducted by H. C. George of the University of Oklahoma, was equally fruitful, and since managers of companies, consulting engineers, and pro-fessors cooperated in these sessions, a cross-section of their opinions on improving the curricula for training the large number of petroleum engineers, which the industry can absorb in-the next few years, was obtained.

Jan 3, 1927

By John J. Reed

This paper was prepared as a supplement to the general review by Dr. N. G. W. Cook. His analysis of the problem in terms of the strain energy involved in making the excavation is excellent. It will contribute much towards a clearer understanding of rock behavior and control. Several of the practical applications described herein can be directly related to Dr. Cook's theories and conclusions, and are based on the very same principles. CONTROLLED BLASTING IN ROCK EXCAVATION Generally speaking, the natural rock is a relatively strong and competent structural material, if we conserve its inherent good properties and perhaps reinforce its weak spots. The difficulty often lies in blasting out the tunnel or chamber without damaging the walls and roof we wish to have remain afterwards. Much progress has been made in the last five years in better understanding the controlled excavation of rock. The specialized techniques known as smooth wall blasting and presplit blasting have now developed from the status of curiosities of rock excavation to the point where these techniques are specified in contracts drawn up for such rock excavation projects as tunnels, underground pourer houses, etc. These techniques have been well described and discussed in previous publications; there is no need to reiterate here. It might be well to point out that recent research has demonstrated the effect that inherent rock stress may have on presplitting in certain directions. Material can be presplit most readily parallel to the direction of maximum compressive stress, and this may not always be in the direction desired. Inherent rock stress measurements by stress relief over coring, etc., may have important value in deciding how to best presplit proposed excavations. In addition, recent work at the Colorado School of Mines has demonstrated the feasibility of con-

Jan 1, 1967

By G. B. Pryde

IN laying out a new mine, provision should be made for the ultimate recovery of as much coal in any given bed as is consistent with safety and economic mining. Though each mining district, if not each individual mine, has problems that make the adoption of any hard and fast rule impossible, certain basic principles are adapted to practically all conditions. One of the most vital is the provision for barrier pillars of ample dimensions to protect all haulage and permanent airways during the life of the property. Where conditions permit, room or butt entries should be driven on the strike or slightly to the raise and rooms turned at right angles to said entries. The width of rooms and room pillars is governed by conditions prevailing in the mines under consideration. A safe rule is: In advancing, extract not more than 25 to 35 per cent. of the entire seam; in exceptionally thick seams, considerably less than 25 per cent. should be taken. Rooms usually vary in length from 250 to 350 ft. (76 to 106 m.) with a barrier pillar of not less than 80 ft. between the last crosscut in rooms, and entry and room crosscuts should be driven on sights; room crosscuts should be driven at right angles to the direction of the rooms. In mines under excessively heavy cover or where roof conditions are bad, rooms should be driven narrow and a barrier pillar left at every fifth to tenth room. This barrier should be of such dimensions that one or more rooms, with pillars of usual dimensions, may be turned through it when the barrier is no longer required. Two of the advantages of such a barrier are the protection of the panel against peaking of roof load during pillar extraction and the easy closing of the entry in case of fire.

Jan 2, 1921

By Carl Henrich

In the winter of 1895 to 1896, during the construction of the Jackson and Cincinnati railroad, running from Addison, Lenawee county, Mich., to Jackson, Mich., in a northerly direction, I had occasion to observe some interesting geological features, described below, in a cut of this railroad made through the low ridge of gravel and sand, dividing the valley of Silver Lake and Silver Creek from the Goose Lake and Goose Creek valley, in Lenawee county. The surface-deposits of this part of the county are, as is well known, of glacial origin. Gently rounded, long ridges of sand, gravel and clay intervene between the marshy bottoms and the lakes of the valleys. The nature of the deposits, varying from a sandy clay or clayey sand to fine and coarse gravel and pure siliceous sand on the one hand, and to a very tough, fine, uniform and often indurated clay on the other, as well as the irregular and sudden changes, sharply divided, between these materials composing the ridges, in the cuts made through them by the railroad, would admit of no doubt that this country owes its present surface-configuration primarily to the action of the last glacial period, which covered its surface with an immense ice-sheet. The well-known ice-markings on the huge granite, schist, greenstone and conglomerate boulders found everywhere imbedded and protruding from the surface, add their testimony to the other characteristics mentioned. Most of the cuts made by the railway through the ridges showed in a marked degree the irregular arrangement and the sudden changes of and between the materials mentioned above. One cut, however, known as Kelly's cut, or Kelly's gravelpit, about 4 1/2 miles north of Addison, and about 1 1/2 miles south

Jan 1, 1897

By G. Bassi

RECENTLY Wallbaum¹ found that copper wires with different degrees of deformation up to 98.7 pct area reduction recrystallize giving a [112] texture, while deformation over 98.7 pct gives either a [l00] texture at low temperatures or a [1ll] texture at high temperatures. Furthermore it was found that the recrystallization temperature as a function of deformation up to 98.7 pct decreases as expected, but increases over that deformation. Wallbaum concluded that the different textures have different recrystallization temperatures. The [112] texture has the lowest and [Ill] the highest. At the same time Bassi² found that for high deformation (over 99 pct area reduction) and for an annealing temperature of 400°C, the [l00] texture first forms and with prolonged annealing time the [12] texture appears through grain growth. This secondary texture does not appear if the wire is annealed at 1000°C before the deformation. From these two papers it might be concluded that the [I12] texture can appear either as a primary or as a secondary texture after annealing. The texture formed in a special case depends on the previous history of the wire. Probably the texture of the wire prior to the last deformation is important. To investigate this, wires were produced by adequate deformation and annealing to give a [l00], a [112], and a [lll] texture. The wires then were given a series of different deformations and were annealed at various temperatures, after which the textures were studied. Experimental Work The copper used was electrolytic tough-pitch (Cu 99.90 pct and 0, 0.04 pct). Three wires with the different initial textures were made in the following way: The [l00] and [112] by drawing a 16 mm rod to 1 mm and annealing it 16 hr at 200°C and 2 hr

Jan 1, 1953

By Meredith Johnson

THE year 1924 saw little change in the production of oil and gas it either Pennsylvania or New York. In the early months of the year the price of Pennsylvania crude oil, $4.00 to $4.50 a barrel, was sufficiently high to cause operators to lay plans for rather extensive drilling opera-tions. But when, in August, the price dropped to $2.85 a barrel, there was no inducement for new work and drilling was curtailed. In spite of the curtailment, however, the combined production of the two states for the year showed a slight increase over 1923, the production being 8;859,000 bbl. in 1923, and 8,901,000 bbl.1 in 1924. The increased production was due entirely to. the continued development of flooding operations in the Bradford field, all other oilfields showing a decline for the year. TABLE 1. Production of Crude Oil in Pennsylvania and New York for the Last Ten Years a Production, Barrels Production, Barrels Year Year Pennsylvania I New York Pennsylvania I New York 1915 7,838,000 888,000 1920- 7,438,000 906,000 1916 7,593,000 874,000 1921 7,418,000 988,000 1917 7,733,000 880,000 1922 7,425,000 1;000,000 1918 7,408,000 809,000 1923 7,609,000 1,250,000 1919 8,137,000 851,000 1924 7,535,0006 1;366,0006 a U. S. Geological Survey figures. b Estimated. Much of the drilling in the southwestern part of Pennsylvania was done in search of gas. Natural gas in Pennsylvania is fast being recognized at its true worth and the increased prices allowed 'the gas companies for their product induced quite a bit of new work. The relative importance of natural gas compared with manufactured gas is shown in Table 2.2

Jan 3, 1925

By Harold Vance

EMPLOYERS of engineers have not always been satisfied with the training that young graduates have received in the conventional four-year course. Specifically, employers of petroleum engineers for a number of years have believed that a four-year course does not allow sufficient time for the student to secure a fundamental engineering background plus the fundamentals of petroleum engineering. A group of California employers went so far as to set up a type of curriculum for a petroleum-engineering course, which was based on four years of undergraduate work and one year of graduate work, with most of the petroleum-engineering courses included in the graduate year.

Jan 1, 1944

[Trans. No.Place Date Vol. Page 1. Wilkes-Barre, Pa.* .... May, '71.. 1 8 2. Bethlehem Pa Aug., '71.. 1 10 3. Troy N. 'l Nov., '71.. 1 13 4. Philadelphia, Pa Feb., '72.. 1 '17 5. New York, N. Y.• ....May, '72 1 20 6. Pittsburgh, Pa Oct., '72.. 1 25 7. Boston, Mass Feb., '73.. 1 28 8. Philadelphia, Pa.' May, '73.. 2 3 9. Easton, Pa Oct., '73.. 2 7 10. New York, N. Y Feb.. '74 2 11 11. St. Louis, Mo' May, '74.. 3 3 12. Hazleton, Pa Oct., '74.. 8 8 13. New Haven, Conn....Feb., '75.. 8 15 14. Dover. N. J.' Mav. '75.. 43] [ ]

Jan 1, 1925

By J. B. NEALEY

MANY nonferrous smelting plants have recently adopted natural gas as fuel with resultant economies, both in cost and efficiency of utilization. Not only has this fuel been used for roasting, reduction, sintering, drossing, and smelting, but also for power. All of the three big smelters near Salt Lake City, Utah, have been changed over from coal and oil firing to gas. Among these is the plant of the International Smelting Co., Tooele, an Anaconda subsidiary, smelters of both copper and lead ores. In the roasting division at Tooele are 32 MacDougall six-hearth roasters, each 16 ft. in diameter and 19 ft. high. Two gas burners are installed on each furnace. These burners are of the single-valve, automatic gas-air proportioning type using high-pressure gas at 10 lb.

Jan 1, 1933

By J. E. Nelson, R. J. Bonnis

Recent completion of Cyprus Bagdad's $240-million modernization and expansion program has registered a 700% increase in ore production with only a 50% increase in labor. Elements of this remarkable achievement include the application of large-scale mining equipment as well as the selection of the latest in processing hardware. Most important, however, was the early recognition that Bagdad's labor personnel is its most important asset.

Jan 4, 1978

Jan 1, 1943

Jan 1, 1900

Jan 1, 1893

By Maurice Rey, Victor Formanek, Paul Chataignon

IT is found when floating oxidized lead ores by sulphidization, that the presence of calcium salts in the water is usually detrimental and lowers the recovery. This effect is particularly marked in dry countries such as North Africa, where the waters often carry large amounts of calcium sulphate and where the ore may even contain gypsum. This effect is particularly marked in dry countries such as North Africa, where the waters often carry large amounts of calcium sulphate and where the ore may even contain gypsum. The effect of calcium salts is readily visible. Whereas in their absence cerussite is quickly stained brown and then .black by sodium sulphide, in their presence the mineral remains very light in color. A similar- effect is produced when barium sulphide is used as a sulphidizing agent instead of sodium- sulphide. Magnesium salts have little or no effect and even tend to reduce the detrimental effect of calcium salts. A study of this phenomenon indicates that it is due to the precipitation of calcium or barium carbonate in contact ,with the mineral simultaneously with the formation of lead sulphide.

Jan 1, 1950

Jan 1, 1928

Jan 1, 1916

Jan 1, 1948

Jan 1, 1894

Jan 1, 1949