Search Documents

By H. N. Wolcott

AMONG the many cases of replacement of one mineral by another, that of quartz or silicates by pyrite, or even other sulphides, is not uncommon, but the reverse of this process does not appear to have been recorded, even if it has been observed. It, therefore, seemed to the writer that the case described below was worthy of record. FIG. I.-GROUND MASS OF CHALCOPYRITE (C) CONTAINING ROUNDED GRAINS OF PYRITE (P) SHOWING DIFFERENT DEGREES OF REPLACEMENT BY QUARTZ (Q), AND ALSO QUARTZ VEINLETS CUTTING THROUGH THE PYRITE. (PHOTOGRAPHED BY REFLECTED LIGHT.) The specimens described in this paper were obtained by R. B. Morton of Idaho Springs, Colo., from the Old Town Mine, in Russell Gulch, and are in the collection of Cornell University, where the writer studied them. In the rough, the specimens appeared to consist largely of chalcopy- rite, with some grains of tetrahedrite. The polished surface of some of

Jan 6, 1917

By Z. T. Bieniawski

Tunneling in coal mines includes driving the main haulageways or roadways which serve as the development entries. Although constituting the lifelines of these mines, little attention has been paid to development entries in the United States in terms of systematic pre-construction planning and design. Coal mine tunnels, as the terminology is used in Europe and elsewhere, are understood in the United States to be the main development entries, either in room-and-pillar mining or in longwall mining. These development entries are not tunnels in the traditional sense since they usually are of a multi-entry type involving entries and cross-cuts, and their intersections. Thus, the design of coal mine tunnels is intertwined with the design of coal pillars. This paper summarizes the results of a three-year research project aimed at improving the design of development entries in U.S. coal mining. A design approach has been developed for this purpose and design procedures for roof support in main entries and for pillar sizing are proposed.

Jan 1, 1984

By Daryl R. Tweeton, Jerry R. Riding, Grant Buma, Frank J. Rosswog

In situ solution mining of uranium has environmental advantages over conventional mining. The leaching of uranium, however, alters the ground-water quality in the aquifer where the mining occurs. Currently, regulations require that the ground water be restored to approximately its original condition. This paper, a summary of a study funded by the Bureau of Mines, reviews the state of the art in restoring ground-water quality after in situ uranium leaching. Current restoration practices discussed include disposal of liquid wastes in deep disposal wells and evaporation ponds, producing from all wells during restoration, and recirculating water purified in surface plants. Methods for predicting the effectiveness and cost of current techniques are presented. Possible alternative techniques are also described. Two restoration operations are discussed.

Jan 1, 1979

By A. J. McEvily, R. C. Boettner, C. Laird

The processes leading to fatigue failure in the low-cycle range were studied to obtain an understanding of the basis of Coffin's law. Particular attention was paid to the manner of mack nucleation and to the determination of the portion of the total lifetime spent in crack propagation. It was observed that cracks are nucleated at surface notches meated during reversed plastic deformation, Principally at grain boundaries, and that crack growth occupies greater than 75 pct of the fatigue life. When inclusions are present, they are often the primary sites of crack initiation. From consideration of the incremental distances advanced by a crack in each cycle and of the lifetimes of different materials, it appears that the universality of Coffin's law arises from the similarity of crack-tip strain for a given applied strain amplitude, irrespecti7:e of material. STUDIES of low-cycle fatigue have been particularly rewarding in that a simple correlation between fatigue lifetime and plastic-strain range has been shown to exist. This empirical relationship takes the forml,2 Nner=C [1] where N is the number of cycles to failure, Er is the plastic-strain range defined as the total plastic strain per cycle (the sum of the tensile plastic strain plus the compressive plastic strain), n, the exponent, is a constant independent of the material to a first-order approximation and often has a value of about 0.5, and C is a constant which for a number of ductile and metallurgically stable materials is approximately 0.65 for fully reversed strain.3 This relationship has been shown to be valid for a wide variety of metals and alloys and is often referred to as Coffin's law. However, it is yet not clear why so many different metals and alloys exhibit the same over-all behavior in the low-cycle range. Less is known about the mechanisms of fatigue failure in the low-cycle range than in the high-cycle range, but it is expected that the processes would have much in common. For example, an important characteristic common to both high-and low-cycle ranges is that fatigue crack propagation can occupy a considerable portion of the total lifetime. This has been shown by Laird and smith4 by a count of the number of ripples present on the fracture surface of copper specimens, each ripple corresponding to one cycle of load. On the other hand, some marked differences have been noted. For example, in copper,5 nickel, and aluminum4 there is a greater tendency for grain boundary cracking to occur as the strain amplitude is increased. The purpose of the present work was to study further the processes leading to fatigue failure in the low-cycle range and to obtain an understanding of the basis for the validity of Coffin's law. Particular attention has been paid to the manner of crack initiation and to the determination of the portion of total lifetime spent in crack propagation. MATERIALS A number of metals and alloys were tested, although more attention was focused on a particular few, once general trends had become apparent. Alloys were selected so as to investigate the effects of crystal structure, number of phases, stacking-fault energy, and impurity content. The materials in this grouping were: high-purity copper OFHC copper 1100 aluminum (commercially pure) 70-30 brass (Cu-30 wt pct Zn)

Jan 1, 1965

By T. Gleason

Problems involved in applying wet scrubbers to gas cleaning coal dust from thermal dryers are reviewed. Careful consideration of all the elements going into a modem coal preparation plant is required in view of the increasing difficulty of applying suitable gas cleaning equipment. This problem arises not only from the presence of finer coals to be handled, but also from the pressures applied by both the general population and the plant operators to improve the standard of gas cleaning performance. The Peabody scrubber is presented by the author as a machine designed to help improve this cleaning operation. Wet scrubbing of fine coal from thermal dryers poses a number of problems in adapting the gas cleaning equipment to the fine particulate matter. Among them are: 1) Dust in gases leaving the thermal dryer cyclones is often extremely fine with high percentages of total dust loading less than 1p in size. 2) Flue gas entering the scrubber is corrosive since the coal fired in the thermal dryer furnace is in the range of 0.7% by weight sulfur or higher. Therefore, comparatively high cost stainless steel alloys or corrosion resistant linings are required for a satisfactory service life. 3) Requirements for residual coal loadings leaving the gas scrubber are continually being lowered, while modern coal preparation operation is imposing heavier burdens on the collection system through introduction into the thermal dryer system of very fine coal previously not recovered. The advent of flotation systems in increasing numbers is typical of this trend. 4) Installation of a scrubbing system on thermal dryers is made primarily to reduce air pollution and product recovery value is of little or no value. Therefore, the operating costs of gas pressure drop and water requirements must be held to a minimum. We have, then, the basic situation which calls for comparatively high cost stainless steel alloy wet scrubbers, which must be highly effective in removing coal fines particularly in the 0 to 5-p size range. Further, the standards of scrubber performance are continually being raised towards the level where gas discharged from the scrubbers must be essentially free of any coloration due to residual dust. In view of the highly refractive nature of fine coal dust, residual loadings of 0.01 grains per cu ft or less are required to provide a color free discharge gas. In the present specifications under consideration a residual coal loading of 0.05 grains per cu ft would be considered color free, since the discharge gases are saturated in the range of 150°F. The steam plume acts as a masking agent at the point of discharge, and upon dissipation of the 150° saturated vapor stream, the effluent gas stream could be essentially color free. The specification under consideration calls for residual solids loading of 0.05 or less grains per cu ft, given a coal size distribution shown in the basic data in Table I. It is noted that the dust laden coal stream has a size distribution by weight of 33% in the 2 to 5-p size range and 55% in the 0 to 2-p size range. The particle size distribution given in the specifications does not detail the percent by weight less than 1-p in size, and more important, the size distri-

Jan 1, 1963

By W. B. Mather

Arkansas' nonmetalliferous deposits are of many different types. The principal types briefly described in this paper are: clays, shales and slates; silica deposits; limestone and dolomite; barite; gypsum; celestite; nepheline syenite; greensand; phosphate; vermiculite; fuller's earth; bentonite; diamonds; sand and gravel. The future development of these deposits is expected to effect profoundly the industrial development of the state.

Jan 5, 1950

By S. S. Clarke

THE opening of sheet-ground mines in which the ore beds are only from 7 to 9 ft. thick led the Commerce Mining and Royalty Co. to con-sider mechanical loading, in order to avoid the high cost of hand shovel-ing in such mines. Scraper loaders were chosen because the capital investment would be comparatively low; because they are small enough to be used in low working faces, and because they can be mounted on a mobile carrier.

Jan 1, 1939

By H. A. Guess

For a number of years I have used for the commercial wet assay of lead generally the ammonium molydate, and occa-sionally the ferrocyanide method. These well-known methods need no detailed description here. In the ore-selling and ore-buying establiahments of the West, 90 per cent. of all wet lead-assays are made by one or the other, and at least nine-tenths of this proportion by the molybdate method. A procedure so well-established must have merit; and, in

Jan 1, 1905

By Fritz F. Prugger, Peter R. Jones

This paper considers some of the main aspects of underground mining in the flat, rich, but deep lying deposits of Saskatchewan. It briefly describes the pertinent geological features as they relate to mining and the practical de-stressing techniques used to allow productive extraction in the high stress environment present in many of the province’s mines. Mining layouts, materials handling, and the evolution of some of the world's largest mining equipment are examined.

Jan 1, 1983

By J. G. Richardson, K. H. Coats

During the initial growth of a gas bubble in an aquifer storage reservoir the injected gas tends to override the water. The resulting low displacement efficiency and high rate of gas travel down-structure make it difficult to maintain water-free production. This paper illustrates the use of two-dimensional, two-phase calculations to simulate this gas-water displacement. Calculations were performed for a stratified aquifer and for several homogeneous sands differing in permeability, porosity and thickness. Results are discussed and compared with performance predictions obtained from the simpler Buckley-Leuerett and Dietz formulas. This comparison indicates the necessity for the two-dimensional calculations in realistically simulating the gravity override of the water by injected gas. INTRODUCTION In recent years natural gas has been stored near markets in aquifers where insufficient storage capacity is available in depleted fields. Operators of these aquifer storage reservoirs have encountered technical problems relating to the gas-water displacement accompanying initial growth of the gas bubble. Injected gas tends to override the water, with a resultant low displacement efficiency and high rate of gas travel down-structure toward spill points. Low displacement efficiency makes if difficult to sustain water-free gas production. Sometimes the fingering of gas down-structure may be so pronounced that the injection rate must be severely curtailed, which excessively lengthens the time required for bubble growth. This paper is concerned with estimating — for given aquifer characteristics and fluid properties — the displacement efficiency, rate of gas movement down-structure and rate of gravity drainage of water behind the gas front. Several published articles relate to simulative capability necessary to handle this problem. The Dietz formula1 and Buckley-Leverett2 method have some applicability to the problem; Woods and comer3 reported one-dimensional, radial calculations which accounted for the two-phase flow of gas and water. Most recent research directed toward understanding aquifer behavior in relation to gas storage has concentrated on single-phase flow in aquifer.4 Douglas, Peaceman and Rachford5 presented a method for calculating multidimensional two-phase flow in reservoirs; their method has been applied in work reported by Nielsen and Tek,6 Blair and peaceman7 and Goddin.8 Refs. 5 and 7 show comparisons between experimental data and calculations similar to those employed here. One purpose of this paper is to illustrate the use of two-dimensional, two-phase flow calculations in simulating the difficult problem of water displacement by gas in a vertical cross-section. The pronounced fluid density and viscosity differences combine with the disparity in horizontal and vertical dimensions of the cross-section to pose one of the more difficult problems in reservoir simulation. The calculations described account for capillary and gravity forces, relative permeability and reservoir heterogeneity. An example reservoir is described and calculated results are presented for a variety of injection rates and values of permeability, reservoir thickness and dip angle. A second purpose is to compare the two-dimensional calculations with results obtained from the Buckley-Leverett and Dietz formulas. For this reason most calculations were performed for a simplified example reservoir to which the latter techniques might reasonably be applied. However, the computer program employed applies equally well to cases involving arbitrary spatial variations of permeability, porosity, reservoir thickness and dip angle.

By D. J. Reed

Concord coal mine near Bessemer, Ala., built, owned, and operated by Tennessee Coal & Iron Div., U. S. Steel Corp., produces only a metallurgical grade for use as coke in blast furnaces of the division at the Fairfield and Ensley works. Capacity of the operation is approximately 800 tph, half of which is delivered to the coke and coal chemical plant at Fairfield after beneficiation to metallurgical grade coal. The remaining portion of the mine run is rock and refuse removed during preparation. Concord mine coal is hoisted to the surface coal preparation plant by an underground slope conveyor. The slope conveyor is 2449 ft long and has a lift of 729 ft. At time of installation the Concord mine slope conveyor was the largest single conveyor unit ever made with respect to belt horsepower and total lift. After several years it became necessary to determine the cause of slope conveyor cover wear.

Nov 1, 1956

By Dorsey A. Lyon, Robert M. Keeney

The utilization of hydro-electriic power in electro-metallurgical industries, aside from purely mechanical operations, may be of two kinds. The electric energy may be used to supply the heat necessary for the performance of the chemical reactions of a metallurgical process, or the electrolytic action of a direct current may be employed for extraction of metals, either in a reduction process or a refining process. In discussing this subject, it is well to distinguish between established industries, which are producing metals and alloys at a, profit by use of the electric current, and the many processes which are either still in the experimental stage or have not even passed the paper stage of development of a patent. That is, we consider electro-metallurgical industries as commercial operations which are now consuming large blocks of electric energy, while processes which are not in commercial operation are only prospective consumers. Also, owing to the difliculty and risk of any attempt to foresee the effect of the European war upon electro-metallurgical industries, we have felt obliged to disregard the war entirely, and state our opinions regardless of its existence. Application of Electric Energy to Metallurgy Disregarding electrolytic refining processes, the applications of electric energy to metallurgy, when considered from a commercial viewpoint, may be classified as follows: Industries Experimental Processes Manufacture of aluminum Electric-furnace smelting of: Electric-furnace manufacture of: Ferro-alloys Copper ore Pig iron Zinc ore Steel In this paper only the above industries and experimental processes will be considered as possible consumers of hydro-electric power in large quan-

Jan 1, 1916

By Walter R. Hibbard

THE increased strength of a polycrystal-line metallic aggregate compared with that of its individual crystals generally has been associated with complex stress distributions at the grain boundaries resulting from atomic irregularity between grains. This disregistry, together with the necessity for adjacent crystals to deform 'compatibly regardless of the single crystal crystallographic strain mechanism, complicates this mechanism so as to increase the metal's resistance to deformation. Although Taylor1 has shown from purely mechanical considerations the requirement for at least five active slip systems to absorb the complexities during the homogeneous deformation of polycrystalline face-centered cubic metals, experimental studies by Barrett and Levenson2 indicate that this is feasible only in a qualitative sense because of deviations from homogeneous deformation. Seitz and Read in their review3 state: "Unfortunately . . . present knowledge of the grain boundary influence is not sufficient to complement the work in single crystals and provide us with a good foundation for treating polycrystals." The purpose of this investigation was to attempt to clarify the gap between single crystals and crystalline aggregates by an analysis of the effects of deformational stresses. Some of the results were described by C. H. Mathewson in his 1943 Campbell Memorial Lecture.21 PREVIOUS INVESTIGATIONS Since the performance of single crystals deformed under pure stresses has been relatively thoroughly investigated, the most significant researches are concerned primarily with deviations from single crystal behavior of large grained specimens. Qualitative grain boundary effects involving the observed amount of slip were reported by Carpenter and Elam5 in 1921. Individual crystals in a two or three grained aluminum specimen deformed by tension acted in the normal manner described by Taylor and Elam4 except for marked modifications at the grain boundaries. There the power to withstand deformation was considerably increased, leaving a ridge on the specimen where decreased slip occurred, often noticeable 34 in: from the boundary. Adcock,6 Yamaguchi,7 Seumel,8 Hirst9 and others have also reported this phenomenon as a qualitative trend. Yet attempts by O'Neill10 and Ljunggren11 to measure a difference in hardness at grain boundaries in undeformed specimens were unsuccessful. Miller12 measured quantitatively the reduction in slip near the boundary between the single crystal and polycrystalline areas of zinc specimens. These effects consisted of two parts: I. Next to the polycrystalline interface the distribution of stresses was so altered

Jan 1, 1948

By F. M. Simonds, E. Z. Burns

The Rawley property is located in the Kerber Creek mining-district, Saguache county, Colorado, at an elevation of 10,600 ft. (See sketch-map, Fig. 1.) Ore was found in this vicinity as early as 1880, and claims covering a large area were located and in many instances patented. The ores, however, being of comparatively low grade, and the nearest railway station, Villa Grove, being some 20 miles away, it is extremely doubtful whether any considerable amount of ore was ever handled at a profit. It is safe to say that several hundred thousand dollars were spent (a large part in building mills) previous to 1902-03. About that time a very capable promoter gathered together a group of these claims and interested some New York people, who had had no previous mining experience, in the purchase of these claims. Following the organization of a company, this promoter became General Manager. As often happens under such conditions, the first step was to erect a mill to treat 100 tons per day. It may not be fair to this enterprise to say that the failure which followed might have been foretold, simply on general principles, but this much is certain—the water supply fluctuates in the course of a season through a wide range and for a considerable portion of the year was inadequate to run this mill at capacity. Further, it is currently reported that some of the mill foundations were placed on ice. However true this statement may be, it is a fact that, when first inspected by us, many of the belts in the mill were held on'their pulleys by means of idlers. A shut-down followed, with a material re-adjustment of interests, at which time we became consulting engineers for the company.

Jan 1, 1914

By R. P. E. Hermsdorf

THE electrolytic refining of metals for the removal of undesirable impurities has become a recognized necessity in the nonferrous field. Copper, lead, zinc, nickel, silver and gold have been produced in this manner for years. The United States Metals Refining Co., realizing that considerable quantities of lead and tin could be made available to the trade if a satisfactory method of purification of these metals could be established, decided to investigate the possibilities of electrolytic solder. In cooperation with Dr. Edward F. Kern, of the School of Mines at Columbia University, the company developed a process of electrolytic refining of lead-tin alloys using a tin-lead fluosilicate electrolyte. A pilot plant was installed in November, 1927, and the commercial unit was put in October, 1929. Since that time thousands of tons of electrolytic solder have been produced in this plant and consumed by all branches of industry that use solder.

Jan 1, 1936

By Albert Smith

THE creep properties of metals have as-sumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Insti-tute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influ-ence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investi-gate creep phenomena because of the sim-plicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals.

Jan 1, 1940

By Thomas Wilson

IN a single-crystal cube of iron the arrangement of the atoms is that characteristic of iron at room temperature: the body-centered cubic lattice. X-ray investigation has shown this structure to be characteristic of iron, as it has shown the atomic arrangement of other metals to be characteristic of those metals also. Rarely do substances have more than one characteristic atomic arrangement. Many physical properties of metals are directly connected with their atomic arrangements, so that changes of arrangements produce changes of properties. Only chemical change influences atomic arrangement. If a difference in the physical properties of a metal is caused by a process which involves no chemical change, the cause of the difference in properties must be sought elsewhere than in the atomic arrangement. Frequently this cause can be traced to alteration of crystal orientation. The orientation of a crystal may be defined as the relationship which the crystallographic axes bear to some quantity of reference. A cube of iron appears cubic whether it is regarded from a face, an edge, or a corner. Yet these three positions represent three different orientations of the cube with respect to the observer. It is evident that the orientation of this cube of iron, unlike the atomic arrangement, is not characteristic of iron but is entirely dependent on the previous history of the cube. Most of the processes of metal working, such as wire-drawing, rolling, and bending, change the orientation of the crystals present in the worked metals. These processes usually tend to produce rotation of the crystals into positions approaching a mean. Specimens of metals show-ing this characteristic are said to possess a preferred, orientation. Tensile strength, ductility, and many other properties are influenced by orientation changes; therefore two specimens of the same metal may show different values of these quantities. In metal specimens possessing a narrowly limited preferred orientation, these quantities will vary in magnitude in different directions throughout the specimens. The investigation of the influence of manufacturing operations upon crystal orientation, and hence upon physical properties of metals, is an important

Jan 1, 1929

By E. S. Davenport, R. J. Hafsten, R. A. Grange

The influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,' and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely relarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar') when the austenite grains are increased in size. More recently, Griffiths. Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745ºF. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245ºF. (675°C), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarsegrained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite—that is, at temperature levels above about 1000°F. (540°C.)—but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to he presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000ºF. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. Material and Experimental Procedure The material investigated was a cornmercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent Mo. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

By R. J. Hafsten, E. S. Davenport, R. A. Grange

The influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,' and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely relarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar') when the austenite grains are increased in size. More recently, Griffiths. Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745ºF. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245ºF. (675°C), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarsegrained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite—that is, at temperature levels above about 1000°F. (540°C.)—but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to he presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000ºF. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. Material and Experimental Procedure The material investigated was a cornmercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent Mo. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

By D. E. Menzie, D. L. Dauben

This paper discusses the physical parameters involved in the slow flow of high molecular weight polymer solutions in porous media. The interacting effects of polymer properties and porous media properties on flow performance are considered. Experiments were conducted with the polyethylene oxides, with molecular weights ranging from 200,000 to over 5,000,000. Frontal advance velocities ranged from I to 30 ft/day. The porous matrix consisted of a flow cell packed with glass beads. Polymer solutions were characterized by viscosity and normal stress measurements. Under certain conditions, unexpectedly high flow resistance was observed. This behavior was observed to be a function of flow rate, pore size, polymer molecular weight and concentration. The polymer solutions exhibit "dilatant" flow behavior in porour media in contrast with the pseudo-plastic behavior in simple flow systems. A theoretical ex-planation of such behavior is presented. INTRODUCTION The use of polymers in the injected water of a waterflood increases oil displacement efficiency by reducing the mobility (k,/pu) of the driving phase. A reduced driving phase mobility results in improvements in the areal sweep efficiency and in the vertical coverage in stratified reservoirs. This mobility reduction may be achieved by a permeability reduction, a viscosity increase or by a combination of the two. Early attempts at increasing the injected water viscosity were not successful because of the poor economics involved. The use of such materials as glycerin, sugar or glycols to increase water viscosity was not economically feasible. Attempts in using certain naturally occurring polymers were not too successful because of the high polymer losses to the rock. A high molecular weight, partially hydrolyzed polyacry-lamide was introduced 3 years ago as a waterflood additive.',' Initial work by Pye' indicated that the presence of these polymers in dilute concentrations decreases the water mobility 5 to 20 times more than would be expected from measurements of the solution viscosity. Such an effect would be of obvious economic value since only a small polymer concentration would be required to accomplish a large reduction in water mobility. This research was designed to study the basic flow mech anisms of polymer solutions in porous media. The interacting effects of polymer properties and porous media properties on flow performance are considered. This study indicates some of the conditions under which these interactions can lead to significant mobility effects. is valid only for Newtonian fluids. For polymer solutions and other non-Newtonian fluids the equation must be modified to consider that viscosity is a variable quantity. Modification of the Darcy equation to include non-Newtonian effects has been the subject of several recent investigations."" The modifications generally adopt a rheological model. such as an Ellis or Dower law model. to Dorous media by defining some characteristic channel radius. Most of these studies showed the porous media flow behavior to be predictable from viscometric data. Investigations involving the flow of high molecular weight polyacrylamide solutions through cores have generally encountered the high flow resistances reported previously by Pye. This high flow resistance has generally been attributed to an in-depth permeability reduction, as evidenced by a reduced permeability to water which has displaced polymer solution from the porous media. Marshall and Metzner" report high flow resistances, which they attribute to viscoelastic effects. In this paper, the effects of polymer molecular weight, pore size, flow rate and concentration are considered. The polymers used are the polyethylene oxides known as Poly-ox. This class of polymers was used because of its availability in a wide range of molecular weights and because of its known ability to propagate well through porous media. THEORY PHYSICAL PROPERTIES OF POLYMER SOLUTIONS The polymer molecule dissolves in water by means of hydrogen bonding, but retains some of its own structural identity while in solution. Nonionic polymers, such as polyethylene oxide, are generally considered to have a random coiling configration. This type of molecule has the ability to "sequester" or hold a large volume of solvent within its coils in a manner similar to that of a sponge. The random coil is easily deformed and under an applied stress