Search Documents

Page Foreword—H. Foster Bain........................ 9 Letter of Transmittal—F. Julius Fohs...................11

Jan 1, 1927

By Ernest L. Bohnet

Jan 1, 1985

[ ]

Jan 1, 1938

By E. H. Jr. Dix

DURING an investigation of high-strength manganese bronze by the Engineering Division of the Air Service, at McCook Field, Dayton, Ohio, particles of a "blue constituent" were noted in the microstructure of most of the bronzes examined. The constitution of the simple copper-zinc base alloy is still a matter of dispute in spite of the fact that the copper-zinc series is one of the oldest industrially important groups of alloys, and has received the early consideration of scientific research. The diagram, according to the most recent work,1 is shown in Fig. 1. The disputed questions involve the termination of the beta field and the line at 470° C. The earliest experimenter, Roberts-Austin, detected an arrest in some of his cooling curves at approximately this temperature and ascribed them to the formation of a eutectic; it has since been proved that there are no eutectics in this series. Shepherd2 was unable to detect any thermal arrests at this temperature; his diagram was essentially as shown in Fig. 1, except that the line at 470° C. was omitted and the beta phase carried down to normal temperatures. Later, Carpenter and Edwards,3 by a very painstaking research, definitely established the authenticity of the line but attributed it to the breakdown of the beta constituent into a eutectoid of alpha and gamma. Microscopic evidence of the formation of the eutectoid is doubtful and it seems more likely to be due to an allotropic change in the beta constituent as shown by Fig. 1. At least for practical purposes, it is more convenient to think of the structure of a 60-40 brass as a mixture of alpha and beta prime crystals rather than alpha plus an unresolvable eutectoid of "apparent beta" as it has often been called.

Jan 5, 1922

By M. J. Kirwan, K. A. Covell

This paper covers a brief discussion of pumping 38° to 41° gravity oil from Wilcox sand wells ranging in depths from 4000 to 4900 ft. in the Seminole field, Oklahoma. As recently as a year ago it was the general belief among Seminole operators that most wells in that district could not be successfully or economically pumped. Also the idea was prevalent at that time that the crookedness of the rotary holes would cause a large amount of mechanical trouble and the use of the air-gas lift would leave the wells depleted with sand conditions and fluid levels unfavorable for pumping. At that time it was predicted that wells would be abandoned when the economic flowing and swabbing period was reached. Contrary to these beliefs it has been demonstrated that wells can be profitably pumped to limits as low as 10 bbl. of oil per day where conditions are favorable. The Serllinole field, unusual in its rapid development, has served as an experimental laboratory for many oil field pumping devices with which this paper will not concern itself. Discussion will be confined to equipment and methods in general use throughout the field. The outstanding features of equipment and pumping operations covered in this paper may be summarized as follows: 1. Pumping equipment from the standpoint of prime movers, energy cost, power transmission equipment, derricks, counterbalances, beam hangers, tubing, sucker rods, pumps, etc. 2. Pumping problems peculiar to the Seminole field, including the proper time at which to change from air-gas lift flowing to pumping. Pumping Equipment There have been no basic changes in pumping equipment in the past 20 years with the exception of some refinements in design brought about by the demand for equipment suitable for pumping deep wells. Results of research in the heat treatment of metals and progress made by the American Petroleum Institute in standardization of equipment, together with the cooperation of oil field equipment manufacturers, have

Jan 1, 1929

By H. O. Hofman

In the blast-furnace smelting of lead, copper and other non-ferrous metals, the largest part of the product obtained is slag. Its formation consumes more of the heat-energy of the fuel charged than any other chemical reaction that takes place. It is therefore of importance to know at what temperatures the different slags will form, so as to be able to choose in a given case the slag that will form at the right point in the operation, will keep the products thoroughly fluid, so as to insure a satisfactory separation, and will permit the consumption of fuel to be reduced to the lowest practicable point. While practical experience has brought out in a general way the leading differences as to the formation-temperatures of Rome silica—iron —lime slags, accurate details are still wanting. The object of the investigation here described was to supply some of these.* Prominent among the men who have worked on the fusibility of silicates are Lampadius, † Sefström,‡ Berthier,§

Jan 1, 1900

By Thomas S. Blair

I FEEL a certain sense of responsibility in bringing before you the subject of the direct process in iron manufacture. I am aware that, in such a body as I have now the honor of addressing, there are few who are not already so well informed upon its past history that it would be a weariness to them to listen to anything else than an account of practical success. Yet, to claim that success involves so much that, if I do not make good my claim, I deservedly expose myself to severe criticism. The whole literature of the art, so far as it relates to the direct process, is, up to this time, but a history of failure. It is safe to say that more money, time, and talent have been fruitlessly spent in the pursuit of this object than in all the other unsuccessful efforts in the whole line of iron metallurgy. A distinguished authority in patent law has remarked that " the invention records of the United States and of foreign countries are filled with the waifs and abandoned relics of these abortive struggles." Dr. Percy, whose great work may be taken as an epitome of all that was worth mention, whether useful or curious, in pig-iron metallurgy, up to the date of its publication (1864), after giving elaborate accounts of various attempts at the direct process, condenses his own opinion of all that had been then effected, into a brief but summary comment upon a pamphlet of one of the sanguine inventors who had said: "It is evident that the present mode of working iron

Jan 1, 1874

By O. W. Ellis

BEFORE entering upon a general discussion of the fascinating, but at present rather controversial, subject of gases in copper, the author feels that some attention should be directed to the work which has been carried out on the solubility of gases in metals. The outstanding contributions to our knowledge of this subject have been made by Sieverts and his collaborators(1) t and by Iwasé.(2) Both the German and the Japanese investigators employed apparatus of the same general design in their investigations. Full reference need only be made, therefore, to the German scheme, which is diagrammatically illustrated in Fig. 1. This, to use the words of Sieverts, which he employed in describing his Burette arrangement of apparatus at the 1928 meeting of der Deutschen Gesellschaft fur Metallkunde(1g): shows a diagram of the usual mode of procedure. A quartz flask contains the metal (for high temperatures a highly refractory porcelain FIG. 1.-SIEVERTS' APPARATUS FOR INVESTIGATING SOLUBILITY OF tube is used) and is connected with the rest of GASES IN METALS. the apparatus by means of a stopcock. The other parts consist of a burette divided into 1/10 c.c., a leveling tube, and art adjus-table mercury reservoir. The burette is connected on one side with the gas inlet and on the other side with the absorption flask; the connection can be interrupted by means of suitable taps. Another tap permits the connection of the flask and the Töpler pump. In an experiment the quartz flask is first exhausted and then a meas-ured quantity of gas is let in from the burette. In the first place the volume of the flask when empty is found by calibration with an inert gas. The pressure is read off on the level tube of the burette, and the temperature measured by means of a thermo-couple whose welded junction lies close to the outside of the quartz flask, which is heated in an electric furnace. In several experiments the quantity of absorbed gas was transferred to a burette by means of a pump and measured.

Jan 1, 1932

By R. H. Frazier, F. W. Boulger

THE performance of welded structures is closely associated with the ductile-to-brittle transition temperature of the steel from which they are made. A low transition temperature is desirable because it indicates that the steel is less likely to fail suddenly at low ambient temperatures. Structures such as bridges, ships, storage tanks, and pipelines are usually made from hot rolled semikilled steel. Changes in rolling practice or chemical composition appear to be the most practical methods for improving the toughness of such materials. This results from the fact that production is likely to be seriously curtailed if improvements were obtained by recourse to heat treatment or complete deoxidation. This paper discusses the effect of variations in carbon and manganese contents on the properties of semikilled steels. The transition temperature, a property to which considerable importance is attached, varies with specimen configuration, testing method, and criterion of performance. Both the Navy tear test' and the keyhole Charpy test were used in the investigation. According to the terms used by Vanderbeck and Gensamer,V he tear test was used to measure a fracture transition and the Charpy test to measure a ductility transition. In either case the specimens absorb considerably less breaking energy in tests below the transition temperature than in tests above the transition temperature. Decreasing the testing temperature of notched-bar specimens seems to be equivalent in its effect to increasing the severity of loading on fabricated structures. Therefore, structures built from steels exhibiting lower transition temperatures in laboratory tests are expected to be less susceptible to sudden brittle fractures in service. Consequently, changes in composition which lowered the transition temperature of the experimental steels were judged desirable. Materials and Methods The steels for this study were made in a laboratory induction furnace and rolled to 3/4 in. plate, using a finishing temperature of 1850°F. Precautions taken to insure reproducible melting and testing practices are discussed in detail elsewhere.' All tests were made on hot rolled steels. The analyses of the experimental steels are given in Table I. The list includes steels with manganese contents ranging from 0.21 to 1.46 pct, at each of five carbon levels. The phosphorus, silicon, sulphur, and nitrogen contents of the steels are reasonably constant. The tensile and notched-bar properties of the experimental steels are presented in Table 11. Both upper and lower yield points are listed, and all values are averages for duplicate specimens. Transition temperatures based on three criteria are given. The keyhole Charpy transition temperatures are the temperatures at which the energy-temperature curves based on averages of four specimens cross the 20 and 12 ft-lb levels. Both definitions of Charpy transition temperatures have been used by other investigators. Charpy tests were made at intervals of 10°F, using a pendulum with an available striking energy of 220 ft-lb and a velocity of 18.1 ft per sec. The specimens were oriented parallel to the rolling direction and notched normal to the surface of the plates. The tear test transition temperatures are based on the usual' criterion of the highest temperature at which at least one of four specimens exhibits brittle behavior. The dimensions of the tear test specimens are shown in Fig. 1. The specimen is loaded eccentrically in tension, with pin and shackle fixtures, through the large holes while submerged in a liquid bath at the proper temperature. A specimen developing a fracture area with less than 50 pct shear or ductile texture is classed as brittle. Tear tests were made at intervals of 10°F.

Jan 1, 1955

Jan 1, 1947

By R. W. Carpenter, J. C. Ogle

It is possible, by using pack-rolling instead of conventional rolling, to reduce a number of metals to thicknesses of 2µm or less. Such thinfoils are generally made at room temperature without intermediate annealing. In addition, pack-rolled foils fail by developing pinholes at thicknesses near 2µm instead of developing the shear cracks usually observed in cold-rolled ductile metals. This paper presents the results of a general investigation of the deformation substructure and texture developed in copper and iron pack -rolled from 130 to about 2µm thickness. Electron microscopy showed that in both metals a fine (0.2 to 0.5?µ m) deformation subgrain structure formed during pack-rolling; in neither case was this substructure grossly different from substructures formed during conventional rolling. The deformation texture formed in pack-rolled iron was quite similar to usual bcc textures; however, in the case of copper, the cube texture was stable during pack-rolling and the normal copper deformation texture was unstable. It is shown analytically that the constraining pack induced a large hydrostatic pressure in the foils during pack-rolling. The pinhole failure mechanism is attributed to the presence of the large hydrostatic pressure during pack-rolling; this strongly suppressed the growth of shear cracks. The stability of the cube texture in copper is also probably due to the unusuul stress distribution developed during pack-rolling. EXPERIMENTS at several laboratories have shown that very thin foils of the common structural metals and many of the rare earths can be made by "pack-rolling". 1-3 The technique was originally developed to make specimens for nuclear scattering experiments and foils for X-ray filters. It is also useful for making experimental laminar metallic composite bodies and foils thin enough for direct examination by ultra-high voltage electron microscopy without the need for special thinning techniques. Pack-rolling in the present context means a three-layer pack, with the material to be rolled into foil comprising the center layer. The outer two layers, which constrain the foil during reduction, are ordinarily austenitic stainless steel. Typically, a 130 µm (0.005 in.) metal strip can be reduced to a final thickness of 2 µm or less by this process. This is accomplished at room temperature, without intermediate annealing. It has been observed that foils produced by this process do not exhibit at any stage of their reduction the severe work-hardening found in strip rolled by conventional cold-rolling methods. Neither is the failure characteristic the same."&apos; Conventionally cold-rolled ductile metal strip fails by developing shear cracks on planes whose normals nearly bisect the angle between the rolling direction and normal to the rolling plane; these are planes of maximum shear stress. In pack-rolling this mechanism has not been observed; failure occurs by the formation of pinholes on the foil surface (penetrating the foil). If pack-rolling is continued the hole density increases. These differences in behavior imply the existence of appreciably different substructure in pack-rolled foils compared to substructure in conventionally rolled material, or perhaps that the geometry of pack-rolling has an effect on the foil behavior. This paper describes an investigation of deformation substructure and texture in some specimens of pack-rolled copper and iron, and some considerations of the stress distribution in the foils during rolling that result from the geometry of pack-rolling. EXPERIMENTAL DETAILS Three different materials were used for pack-rolling in the present work: soft copper sheet (99.8 pct Cu, 0.03 pct 0, electrolytic tough pitch) and two types of iron, Ferrovac E* and Armco iron. Each was "Crucible Stccl Co. initially in the form of 130 µm annealed strip with grain size ranges of approximately 10 to 40 µm. The initial texture of the copper (determined as noted below) was the normally observed cube type (001)[100]; there was evidence of a small amount of material in the cube-twin orientation reported by Beck and Hu.4 The initial texture of the Ferrovac E was similar to that reported for recrystallized iron by Kurdjumov and sachs,5 who list the principal orientations as {111}<112>, {001}<110> 15degfrom RD and a weak component {112}(110) 15 deg from RD. The starting texture of the Armco iron was not determined. Pack-Rolling Procedure. A four-high mill was used for all specimens. The work roll and backing roll diameters were 1.625 and 5.25 in., respectively. The peripheral roll speed of the work rolls was about 2.5 in. per sec. All foils were initially reduced from 130 to 100 µm by conventional straight rolling and then inserted into a pack, without any intermediate annealing, for further reduction. The pack consisted of an 0.033 in. (838 µm) thick 3 by 6 in. polished sheet of austenitic stainless steel, folded to make a 3 by 3 in. jacket. After folding, the jacket was given a small reduction to close the fold tightly before insertion of the foil. During pack-rolling a constant change in roll spacing was made every third pass. The roll-spacing change corresponded to a 5 pct reduction in thickness for a new pack. This approached a 10 pct reduction when the pack had decreased to about half its original thickness. At this point the deformed pack was discarded and a new one

Jan 1, 1970

By Edward W. Parker

One of the most important features of the coal-mining industry of the present day is one that is common to the majority of industrial enterprises—the substitution of mechanical methods for hand-labor.

Jan 1, 1900

By Arthur Taggart

SOME years ago, A. M. Gaudin and one of the authors published a paper showing removal of tar acids from solution by sulfides preferentially as compared to gangues (specifically by galena as compared to quartz).1 The underlying phenomenon was classed as adsorption, and the paper went on to develop the general thesis that so far as water-soluble frothing and collecting agents in flotation are concerned, the phenomenon of adsorption is one of controlling importance. Adsorption was defined in that paper as "a process of rearrangement of a system, which results in establishing a difference in concentration, as between the interfacial layers and the bulk of the phases, of a substance or substances initially uniformly dispersed in one or several of the phases." The paper went on to develop the relation between adsorption and surface energy according to Gibbs&apos; equation (which may be thrown into the form U/c = KdT/dc, where U = excess concentration in surface layer, c = concentration, T = surface tension, and K is a constant), and pointed out that, according to this equation, degree of adsorption and change in surface tension vary directly. The present paper offers a somewhat different definition for the term adsorption; and sets up, in sweeping terms, the generalization that simple chemical reaction underlies the functioning of the flotation reagents which control mineral collection, when these reagents are soluble in and act from solution in the water of the pulp.

Jan 1, 1930

By E. G. Woodruff

(Butte Meeting, August, 1913.) FEW authors of treatises and papers on engineering subjects have . given adequate attention to topographic maps.. The statement applies especially to mining engineering in all branches. Even those who have discussed such maps have treated the subject only in a general way. Therefore it is proposed to outline in this paper a few of the uncommon, yet important relationships which topographic maps and their by-product, structure-contour maps, have to modern methods of mining investigation and development when the facts depicted on such maps are properly interpreted. Topography, as suggested by the etymology of the word, menus a detailed description of particular places. Written descriptions have been found less effective than the pictorial representations, therefore attempts have been made in various ways to picture the surface features of places. Lines and shading have been used, hachures drawn, and, finally, the contour topographic map. To a large extent this style of snap is the result of the demands of engineers. It is designed to meet their needs far more than those of the man untrained in engineering. In fact, the average man obtains a better idea of the topography of an area from the hachure system than from contour maps. . Since the maps. have been made chiefly for the use of the engineer, they ought to meet his demands on the one hand, and, on the other, should be used by him to the fullest extent. Such maps, when properly made, accurately portray a portion of the earth&apos;s surface and should present the topography better than a personal examination of the area without a map could present it, because the person making such examination views only a limited portion of the surface at a time, and estimates distances only roughly with his eye. Let the engineer consider carefully the fact that in many instances the topographic map is superior to a personal examination of the surface features of a property because the map is based on careful instrumental measurements, whereas the eye gives imperfect data because it can be used merely for the estimation and

Jan 6, 1913

By Mark J. Klein

An internal-friction profile induced by nitrogen in Cr-35 at. pet Re was studied as a function of nitrogen concentration and heat treatment. From these studies, the solubility of nitrogen in this alloy was deduced. The equilibrium solubility of nitrogen in chromium does not appear to be substantially changed by the addition of 35 at. pet Re to chromium. However the precipitation kinetics of nitrogen from solution are significantly decreased. IT has been found that rhenium has a beneficial effect on the low-temperature ductility of Group VI-A metals. As part of a study to investigate the mechanism of this increased ductility, it was of interest to compare the concentration of interstitials retained in solution in one of these ductile bee alloys with the concentration retained in solution in its base metal. In this regard, a study of the solubility of nitrogen in ductile Cr-35 at. pet Re was selected for this phase of the investigation because the solubility of nitrogen in the base metal, chromium, has been determined over a fairly large temperature span.1-3 In addition, nitrogen is known to have an embrittling effect on chromium,4 but does not appear to have a comparable embrittling effect on Cr-35 at. pet Re.5 The experimental method selected for this study was the measurement of internal friction. This technique allows interstitial-concentration measurements to be made in bee metals that are sensitive to small changes in the concentration of a particular interstitial, even when other interstitials are present. When subjected to a cyclic stress, interstitial atoms in solid solution give rise to an internal-friction peak whose origin is the stress-induced ordering of interstitials into preferred lat- tice sites. These internal-friction peaks signify a dissipation of elastic energy which is greatest when the period of oscillation is comparable with the relaxation time for the attainment of an equilibrium interstitial distribution. For dilute interstitial binary alloys, the height of the internal-friction peak is proportional to the concentration of interstitial atoms in solid solutions. snoek8 has shown that the internal friction, Q-1, may be expressed by the equation where A is the relaxation strength, ? is the angular frequency, and 7 is the relaxation time. The relaxation strength, A, is proportional to the concentration of interstitials taking part in the relaxation if no interaction occurs between solute atoms. Thus values of peak height, which can be determined as a function of temperature, give a measure of the relative concentration of interstitial atoms in solution at various temperatures. If equilibrium has been attained, the peak heights will be proportional to the interstitial solubilities. The constant that relates A to the interstitial concentration can be determined experimentally from peak-height measurements as a function of concentration for specimens of constant crystallographic orientation. When this has been done, Q-1 measurements can be used to determine solubilities according to the equation C - KQ-1 where C is the soluble interstitial concentration and K is a constant that can be experimentally determined. It is possible, however, that lattice imperfections may bind interstitials to certain lattice sites. Internal friction does not measure these interstitial~, but does measure interstitials which are free to move in the normal lattice sites when subjected to an applied oscillating stress. On alloying the pure metal with a substitutional

Jan 1, 1965

By Dever C. Ashmead

Anthracite was first mined in the Wyoming Valley and sold as an article of commerce in 1808. As some preparation has always been necessary to make it ready to burn, the preparation of anthracite must date back over a hundred years. Two vital factors have determined to a large extent the degree and the method of anthracite preparation. These are, first, the character of the beds worked and the methods by which they are mined and, second, the equipment used and practices followed in the burning of the coal. It is not the intention here to go deeply into these phases of preparation as a paper of no mean length could be prepared on the history of either. Rather, the intention here is to point out the main considerations and to show the influence they have exerted on the preparation of anthracitc. Mining Methods and Their Relation to Preparation In the beginning of the nineteenth century, the coal beds were virgin with the possible exception of some outcroppings that had been worked, to a slight extent, by the Indians. It is known that the American aborigines had a, knowledge of the use of this fuel, because when the Wyoming Valley was purchased from them, in 1754, they mentioned the fact that, by selling the land, they would lose their coal. Real mining of anthracite began about 1808 when Judge Jesse Fell, of Wilkes-Barre, discovered that the "common stone coal of the valley" could be burned in an open grate. For some years thereafter mining was conducted near the surface. The working p1aces were driven narrow; only the best of the coal was selected and the remainder was left in the ground. Only the lumps could be used, as no market existed for other sizes. As time passed, however, it became necessary either to go farther into the ground or to widen the working places. When these places were widened, falls of roof were apt to occur, making it necessary

Jan 1, 1922

By T. lkeda, R. S. Montgomery. A. Hara

Actual test specimens used in the previous laboratory wear investigation,&apos; were fully characterized and the data is given in Table 1. Most of the carbides tested could be placed into groups of similar mean grain size. When the wear rates of the members of these groups were plotted as functions of their hardnesses, a family of curves resulted; curves for groups containing data from larger grained composites were at lower wear rates at the same hardnesses. Most specimens tested showed only A-1 porosity (ASTM Standard designa-

Jan 1, 1971

By Daniel Houdouin

Data is frequently collected in mineral processing plants in order to evaluate operating performance or to model process units. Metal concentrations, circulating loads, products flow rates, classifiers efficiencies, flotation units recoveries, grinding mill efficiencies are typical parameters calculated from plant data. The validity of these calculations depends strongly upon the reliability of the data used for that purpose. The objective of this paper is to illustrate that flowrates, efficiencies and rate parameters of mineral processes are more reliable when calculated from balanced data rather than from raw data. Using variance-covariance matrices of balanced data produced by automatic mass balance packages (including flow rates, concentrations, percentage of solids and size analyses), variances of separator efficiencies (flotation or classification) and of mill grinding rates are derived. The variances are compared with those of variables calculated from raw data. The advantage of using balance data is illustrated with real data from flotation, grinding and classification units.

Jan 1, 1984

Jan 1, 1920

By William N. Matheson

The major consideration in any management and engineering decision is the economic evaluation of factors. The right decision is the best cost decision, provided of course that it is the safest. Changes, improvements, and advances in mining technology, as in any business, come about through the pressure of economics in combination with the inventiveness and engineering abilities of efficient mine operators. Without proper economic evaluation and an appreciation of profit and loss of an operation, advances in mining methods would come about at a slow pace, if at all.

Jan 4, 1959