Search Documents

LUTHER B. EAMES, Pueblo, Colo. (written discussion*).-In reading Mr. North's interesting paper, several points have been noted that appear to warrant discussion. With a feed all through 20 mesh, I feel inclined to question the use of steel balls as large as 2 in. in a tube mill. I have seen balls as small as-3/4 in. used for the dry grinding of cement clinker, and surely many more points of contact would result from smaller balls. This would seem to be desirable in a mill as short as 6 ft. The heavy load in the classifiers would also indicate a high proportion of returned pulp. I hope that some discussion by Mr. North -and others may develop this point. The flow sheet on page 1181 shows the solution returning from the dam valued at 40 c. per ton being added to the last decantation tank. Theoretically, this solution should not be added to that of a lower value. As I calculate it, if this solution were added to tank X the solution finally discharged from tank Z would be reduced in value by nearly 4 c. per ton.

Jan 10, 1919

F. E. Thompson, Pottstown, Pa.: If Mr. Webster's endeavor to open up the subject of cast-iron should prove as prolific of results as did the discussion on " The Physics of Steel," he must certainly feel richly repaid. His remarks concerning the secretiveness and conservatism of the average foundry-man recall to my mind an instance of a blast-furnace which, for the last year, has been producing much foundry-iron. The manager, believing that much more of his product could be used in the foundry than the foundry-men were will-

Jan 1, 1896

By D. Harker, M. J. Murphy

THE mechanism by which age-hardening takes place is still not completely understood. The principal theories range from the extreme of "precipitation-hardening" to that of "order-hardening," with many intermediate gradations. In the hope of obtaining new data on which to base a choice among the many theories, the authors have made electron micrographs of formvar replicas taken from metallic specimens at various stages of age-hardening. The results so obtained on an alloy of 2 per cent beryllium in copper and one of 20 per cent molybdenum in iron will be described in the following pages, as well as the technique used in preparing the replicas. PREPARATION OF FORMVAR REPLICAS OF METALLIC SPECIMENS This section is concerned with the techniques that have proved successful in preparing formvar replicas for studying the microstructure of metals with the electron microscope. Because of its simplicity and accuracy, the formvar replica1 method developed in the General Electric Research Laboratory has been used exclusively, since it is much simpler than the silica replica method of Heidenreich and Peck2 and produces as good results. The formvar method to be described requires a technique acquired only by practice, and no foolproof set of rules can be given. It is a rapid method and a replica can be obtained in less than five minutes under favorable conditions. This does not mean that perfect replicas can be produced every five minutes, but rather that one can well afford to take several strippings* in order to produce a replica of high quality. The metallographic technique required for replica work-very fine polishing and etching with very dilute solutions-is described here. It can be said, in general, that almost any surface that has been carefully prepared for a photomicrograph at 1000 or more diameters can be used to obtain a replica for the electron microscope. PREPARATION OF METALLOGRAPHIC SPECIMENS The preparation of the metallographic specimens is somewhat more exacting than that usually given to samples to be used for inspection under the light microscope. After much experimentation, it was concluded that the best method consists in polishing the metal through to the coarse cloth, then etching and repolishing on final cloth until the layer of distorted metal is removed. After this procedure has been completed, a dilute etch-to approximately the depth necessary for a micrograph at 1000 diameters-usually produces a sur-

Jan 1, 1945

By E. H. Hamilton

WHEN starting a series of experiments on the use of powdered coal in lead blast furnaces to replace coke, I realized that in copper smelting the problem is simpler because the sulfur recovers the copper in the form of matte. In lead smelting there are greater difficulties because a reducing atmosphere must be maintained in the active, zone corresponding to each tuyere in order to get the best recovery of lead. Therefore, the feed of powdered coal must be quite regular, uniform and under control. The molten products issuing from the taphole are the resultant of the work of all the tuyeres and it can readily be con-ceived that one part of the furnace may be forming slag with a higher lead content than the slag formed in other parts of the furnace. At first, we used only one tuyere situated on the back of the furnace. This was for the purpose of getting all of our regulations under the regular operating conditions. We tried every known system of feed and found they were not dependable and our present system was finally worked out, and so far as we know, is the only working system that will give uniformly good saving in lead blast furnaces. We placed a Bristol self-recording thermometer on the feed floor. This gives a 24-hr. continuous record of the temperature of the gases leaving the furnace. We put a self-recording gage on the "15-lb." air used in the injector. A second recording Bristol gage was put on the low-pressure air (40 oz.). I realized that it was necessary that we should know the exact weight of coal going into each tuyere and that it should 'be under observation at all times. L. W. Kirk was assigned to the problem and developed the open sight feed and the distributor, so that we now have the coal being fed into each tuyere in sight of the men in charge. We have an apothecary's balance beside the furnace, and the operator takes the pan and inserts it under the stream of falling powdered coal for one minute, and places the pan on the scale, the other scale pan having weights indicating the desired amount to be fed to each tuyere per minute.

Jan 10, 1922

By F. D. Weeks

The Salida smelting plant, owned by the Ohio & Colorado Smelting & Refining Co., is situated at an altitude of 7,000 ft., about 2 miles west of Salida, Colo., and 215 miles southwest of Denver. Salida is a division point on the Denver & Rio Grande R. R. where the narrow-gage line serving the San Juan region joins the through standard gage. This narrow-gage road also serves the coal and coke companies at Crested Butte and the lime quarries and mines at Monarch and Garfield, which are only 20 miles distant. These facts, together with the possibility of an appropriate site, doubtless influenced the builders to locate at this point. The smelting plant and yard occupy 80 acres of land on the northeast side of the Arkansas River. The slope of the ground is such as to permit of the ore being delivered by cars at a point 25 ft. above the feed floor; and in front of the furnaces there is a fall of 50 ft. for the slag dump. A recent purchase of river bottom has provided slag room for 20 years. As originally constructed, the plant consisted of four blast furnaces, 40 by 144 in. at tuyéres, two copper-matting furnaces, dust chamber, stack, power plant, blowers, sampling works, and one railroad trestle about 16 ft. from bed floor to rails. Later 12 hand roasters of excellent design were added and the practice of smelting leady matte in a copper-matting furnace was abandoned. Since the plant passed under the present management the equipment has been increased so that the following is a brief description of the same at this date: Two lead blast furnaces, 48 by 180 in. at tuyéres, 17 ft. 6 in. tuyéres to feed floor; four lead blast furnaces, 40 by 144 in. at tuyéres, 17 ft. 6 in. tuyéree to feed floor; two copper-matting furnaces, not used; blast-furnace flue, 900 ft.; area 245 sq. ft.; blast-furnace stack, 150 ft.; above furnace floor, 190 ft. When smelting a 500-ton charge per day, the gases approximate 63,700 cu. ft. per minute and travel at a speed of 260 ft. per minute. The slag is hauled by a 10-ton electric locomotive; the slag shells and settler refuse are elevated to a bin on the feed floor by an electric hoist. The matte is tapped in 1,600-lb. cakes and loaded into cars

Jan 1, 1916

By Eugene Guccione

Australia could eventually become a major world supplier of uranium oxide-but how quickly that happens depends on the outcome of a highly complex and emotional battle among different special interests.

Jan 1, 1977

By Philip D. Wilson

OF all the metals in the war program the demand for and the production of magnesium have increased percentagewise the most. In the prewar year 1939 the production was 3350 tons. The war program, twice expanded, now provides for nearly one hundred times that amount annually. The goal announced by the War Production Board in February 1942 was 362,500 tons per year. Be- cause of the development during the year of satisfactory types of incendiary bombs other than magnesium this objective has been somewhat reduced but the capacity of the plants already built or under construction will be huge. The Aluminum and Magnesium Division of the W.P.B. has had the responsibility of planning and implementing this expansion and of providing fabricating facilities as well for this greatly increased tonnage of magnesium ingot.

Jan 1, 1943

By Max W. Ball

Our ever-increasing use of minerals has been the outstanding fact in our American economic development. The rise in our standard of living in the past century is without equal in human history. Nowhere in time or place has the man who works lived so well, or the man who cannot work been so well cared for. We live in a new world, even the poorest of us, that our forebears of 1849 could not have dreamed. That new world has come mainly from our use of minerals. Our per capita use of nonmineral products has grown too, but by only a modest amount. Food consumption per person has grown about 15 per cent in the past fifty years; lumber use per person ,has fallen 56 per cent and that of wood for fuel 65 per cent. Of all the products of field and forest, our use, per capita, may have increased by one fifth during the present century. In contrast, our per capita use of minerals has multiplied several times. Each of us uses 2% times as much steel and 16% times as much petroleum as our fathers used in 1900. In less than half a century our per capita consumption of all minerals has probably risen by 200 to 250 'per cent. Man once built with wood; today he builds mainly with brick and stone and steel. Once he traveled by the power of hay and oats; today he travels by the power of coal and oil. Rubber made from minerals is already better for some uses than rubber tapped from trees; before long it will be better for most and perhaps all uses. Even our ladies' graceful legs are clad in mineral fiber, where once animal or vegetable fiber would have covered them. Our high standard of living is a product of the machine.. The machine is made of minerals. The machine is driven by minerals. The machine age is a mineral age.

Jan 1, 1949

By A. M. Nicholas

WheN attempting to lift mill pulp containing a considerable percentage of wolframite, in an ordinary bucket elevator, difficulty was encountered from the tendency of the tungsten minerals to settle, on account of their high specific gravity. Lifts not exceeding 20 ft. (6 m.) could be accomplished without particular difficulty, because there was insufficient time for consolidation of the heavy minerals in the bottom of the bucket; but with higher lifts, the heavy tungsten minerals would settle so solidly that when the bucket turned over at the top of the elevator the contents could be only partially dumped. In this case it was necessary to lift the material a distance of 34 ft. (10m.); hence some means had to be adopted to prevent settling, at least to such an extent that the material could be dumped from the buckets. To reduce the carrying time to a sufficient extent would have required a belt speed of 475 ft. (144.7 m.) per minute, which was not feasible. It was decided to try, by vibrating the belt about midway of its span, to keep the material sufficiently agitated during elevation to prevent settling. Underneath the rising side of the belt was placed a 12-in. (30.48-cm.) idler pulley, 18 ft. (5.5 m.) up in the total lift of 34 ft. The idler pulley was set eccentric by % in. (19 mm.) and it was hoped that the vibration thus imparted to the belt, running at a speed of 280 ft. (85 m.) per minute, would prevent settling in the buckets. It was found that the pressure of the belt on the idler, due to the small inclination of the elevator, was not sufficient to overcome sliding on the idler, and the agitation was insufficient to accomplish the desired purpose. The idler was then connected to the drive shaft of the elevator through an intermediate pulley, gearing down to a speed of 20 r.p.m., so that a positive vibration was imparted to the belt; this imparted enough motion to the belt to prevent settling and the contents of buckets dumped satisfactorily. Protecting Elevator Belts When elevating, from the crusher, a rock which was very sharp and abrasive, considerable difficulty arose from cutting of the belt under-

Jan 1, 1918

By E. H. Bunce

CONTINUED progress in zinc metallurgy has been shown during 1933 by the adoption of new methods as well as the modernization of old processes and equipment, and by the initiation of new fields of activity for future advancement. The use of suspension roasting continued to grow as its advantages and adaptability became increasingly, apparent. The process developed by the National Smelting Co., Ltd., several years ago, of completely roasting on large sintering machines with utilization of the gas for acid manufacture has worked so successfully that an additional machine was installed during the year. At both the Swansea and the Avonmouth Works all of the ore for smelting is now roasted on the large sintering machines, thereby completely eliminating the old hearth-roasting furnaces. Work continued on obtaining partial purification of zinc ores from lead and cadmium by close control of conditions on the sintering machine, and in a few instances by chlorine additions to the ore before sintering. Ores so treated were either partially roasted or com-

Jan 1, 1934

By S. Jana, C. M. Wayman

The reverse transformation of bcc martensite to the fcc phase was studied in an Fe-33.95 wl pct Ni alloy by nzeans oj dilatometry, melallography, and electron microscopy. Upon "slozc" heating (-1°C per min) length cJmnge us temperature plots showed u gradual contracLion over the temperature range 200" to 280"C ,followed by a more abrupt contraction beginning a1 -280°C. Howet,ev, zchen the heating rate was increased -4°C per tnin, no gradual contraction was observed and only the abrupt contraction starting at -2BO"C was found. Thus on slower heating- the AS "temperature" for the subject alloy, unlike the MS temperature, is better defined as a range of temperatures. Both optical and transmissiorl electron microscope observations showed that some of the martensite plates exizibited a partial loss of transformation twins during reversal. The midvib region of the martensite plates disappeaved relatively early duirng the reversal. Metallographic observations slowed that the earliest detectable stage of the rezlerse tvansforrvration begins (axd Moues inulardly) at The Martensens i te - parent interface. At higher temperatirres, the. formation of martensitically reversed jcc plates within the bcc martensite plales was observed. It is concluded that the reverse transformation consists of a diffusion less process (martensitic); but this is ps-obably aided by a prior or simultaneous dijjusiorz-comltvolled process, at leasl in the case of slower heat-ing' experiments. ALTHOUGH numerous investigations have dealt with the parent-to-martensite ("forward") transformation (fcc — bcc) in Fe-Ni alloys, comparatively little is reported on the ("reverse7') martensite-to-parent transformation.'-4 Even though such reverse transformations have been studied in detail in some nonferrous systems, one of the difficulties of studying the reverse transformation in most ferrous mar-tensites is that the martensite decomposes by tempering during heating. However, carbonless Fe-Ni alloys do not exhibit this difficulty since the transformation in these alloys is completely reversible. The present investigation represents an attempt to shed more light on the nature and mechanism of the martensite-to-parent transformation. 1) EXPERIMENTAL PROCEDURE 1.1) Alloy Prepatation. Fe-Ni alloys of compositions near 34 wt pct Ni were prepared from zone-refined iron (99.994 wt pct Fe) and high-purity nickel (99.999 wt pct Ni) by induction melting in recrystallized alumina crucibles in an argon atmosphere, with prior vacuum evacuation to 10"3 mm Hg. The alloys were homogenized by induction stirring in the molten state for 5 min. After solidification, the alloys were further homogenized in evacuated quartz capsules for 96 hr at 1230°C. 1.2) Dilatometry. Slices of the ingot were hot-forged (750°C in air) into approximate rod form and these specimens were then hot-swaged (750°C in air) into long cylindrical rods 0.55 mm diam. From the rods, specimens about 1 in. long were cut. These were then vacuum-annealed for 24 hr at 1200°C, cooled to room temperature, and subsequently transformed to martensite in liquid nitrogen (whereby about 40 pct transformation was obtained). Dilatation measurements were made by observing length changes in a vacuum dilatometer with an externally mounted LVDT sensing element. 1. 3) Preparation of Electron Microscope Specimens. Slices of the ingots were cold-rolled (with intermediate vacuum anneals) to -0.020 in. Out of these rolled sheets, specimens (about 1 by 1 in.) were cut. These were then vacuum-annealed, transformed to martensite by cooling in liquid nitrogen, and subsequently heated from room temperature to various temperatures to effect either partial or complete reverse transformation. These specimens were then chemically polished to 0.002 in. in l:l HsOz (30 pct) and &PO4 (85 pct) solution, and thinned to electron transparency in an electrolyte consisting of 150 g CraOs, 750 ml glacial acetic acid, and 30 ml ~~0.~ Observations were made with a 100-kv Hitachi HU-11 electron microscope equipped with an HK-2A tilting device. 1.4) Optical Microscopy. Metallographic observations were made with a Leitz MM5 metallograph on the same 0.020-in. sheet specimens as were used for electron microscopy and on bulk specimens which were 0.2 in. or more on a side. The chemical thinning solution when cooled below 20°C also served as an etchant for this alloy. Observations of surface relief were made with a Zeiss interference microscope employing a Thallium light source of wavelength 0.54 p. Specimens for interference studies were prepared by two-stage polishing on Buehler vibromet polishers using 0.3 and 0.05 p alumina abrasives. 2) EXPERIMENTAL RESULTS 2.1) Comparison of the MS,AS, and Af Tempera-tures wTth Previous Re sults. The AS aLd Af tempera -tures of several Fe-Ni alloys were determined dila-tometrically. The MS temperatures of the same alloys were determined by continuously lowering the temperature using a mixture of isopentane and liquid nitrogen and observing the highest temperature at which a prepolished specimen showed surface upheavals. For the present the As temperature is defined as the temperature at which an abrupt decrease in length occurs in the dilatation plot. The Ms,As7 and A determinations in the present investigation and those of Kaufman

Jan 1, 1968

By R. W. Raymond

THE death of Louis Janin, which took place Mar. 6, 1914, at Santa Barbara, terminated the earthly career of almost the last survivor, and one of the most illustrious, members, of that group of American mining engineers and metallurgists who, in the last quarter, of the nineteenth century, directed the development of the mineral resources of the Pacific slope. Louis Janin was born in 1836 at New Orleans. His grandfather, an officer in the French army, had emigrated to this country, with his family, at or before the outbreak of the French revolution. His father became an

Jan 7, 1914

By T. A. Simpson

The search for ore continued at its relentless pace throughout 1967. Canada, South Africa and Australia plus a few scattered localities on the globe reported minerals finds of significant importance. Many of the reported finds were not high grade ore, but they nonetheless will assist in sup- plying a highly industrialized, mineral hungry world. No longer does inaccessibility and remoteness close an area to mineral exploration and development. The communication and transportation systems of today have closed the gap and, moreover, the demand for essential mineral commodities is causing price shifts which encourage exploitation of deposits heretofore considered uneconomical.

Jan 2, 1968

By ARTHUR THACHER

PRIMITIVE man supplied his wants as they arose; as he became more civilized he anticipated them by producing more regularly and storing the products for future use. This tended to cheapen' production and prevent ' violent fluctuations and therefore tended to increase consumption. In order to anticipate our wants, we must know what these wants will be, and this can be .determined only by statistics. 'While we have made great progress in gathering statistics, they are still far from what they should be; especially metal statistics. We determine fairly, well the amount produced, but this does not answer all inquiries because of the erratic conditions of mining, it is necessary to carry larger stocks of metals than of most other articles; moreover, as metals are more or less durable, it is difficult to determine the actual consumption. We often count under consumption what is being produced and sold, while the actual consumption is what is being worn out.

Jan 1, 1921

By Thomas Read

AMONG the large number of deep mines in the world there are several which do not differ much in depth. The St. John del Rey mine, in Brazil, has reached a vertical depth of 6726 ft. below the top of its shaft; miners enter it, however, through an adit which intersects the shaft 324 ft. below its top, wherefore it might be said that the mine is really only 6400 ft. deep. In the Kolar gold field of India there are a number of deep shafts, one of which reaches to a vertical depth of 6140 ft. below surface. In South Africa also there are a number of deep shafts, the Village Deep being 6100 ft. early in 1921. The City Deep, Ltd., proposes to sink to a depth of 7000 ft. but pre-sumably by the time it does so the St. John del Rey will be deeper than that, since it has been increasing in depth at an average rate of about 150 ft. per year. The deepest shaft in the United States, the Tamarack No. 5, although it is only 5308 ft. deep, actually approaches nearer to the center of the earth (4100 ft. below sea level, as against 3958 ft. , at St. John del Rey). The deepest workings in the Calumet & Hecla go down to 4600 ft. below sea level. The St. John del Rey is not only the deepest, mine in the world, but it also is worked by the oldest registered English mining company, which was organ-ized in 1830 to work a mine at a considerable dis-tance from this one. That mine proved unprofitable, and in 1837 operations were transferred to the. deposit now under discussion, where operations have been prac-tically continuous ever since.

Jan 6, 1923

[FUQUA, H. B. and Thompson, B. E.: Oil and Gas Development and Production in North Texas for 1933, 107, 320; for 1934, 114, 417 Oil and Gas Development in West Texas 114, 438 FURMAN, W. F.: Heat and Corrosion-resisting Alloys. Printed in Oil & Gas Jnl., June 13, 1935 Furnace-bottom sand, uniformity, 73, 390 Furnace control, Isley apparatus, M27, 502 Furnaces (See also Holt-Dern; Blast Furnaces; Roasters; Wirebar, etc.): annealing: electric, 89, 424 gas-fired, 89, 425 gas vs. wood for nonferrous metals, 89, 422]

Jan 1, 1936

By D. W. Fuerstenau

THE object of this article is to point out the experimental relationship which exists among contact angle, adsorption density, zeta potential, and flotation rate data. In each of the experiments discussed in this article, the surface properties of quartz, as a function of pH, were measured in solutions to which constant quantities of dodecylam-monium acetate were added. Morrow1 and deBruyn2 worked with solutions containing 4.08x10-5 moles per liter, whereas Fuerstenau3 and Seele worked with solutions containing exactly 4x105 moles per liter, but this difference is not significant. The pH of the solutions was regulated with HCI or NaOH in all cases. In each case, the addition of collector was constant, but the concentration of dodecylammonium ions decreased because of the formation of dodecylamine at higher pH values.2 Contact Angles: Gaudin and Morrow1 presented data for the contact angle of quartz in solutions containing 4.08x10-5 moles of dodecylammonium acetate per liter between pH 2 and pH 10.15. Using the same captive bubble techniques, the writer measured contact angles on quartz in solutions containing 4x105 moles of dodecylammonium acetate per liter at pH values ranging from 9.9 to 13.2. Both sets of data are presented in Fig. 1, in which the contact angle in degrees is plotted as a function of the pH of the solution. From pH 2 to about 8, the contact angle

Jan 1, 1958

By R. H. Wightman, G. H. ADAM

In order to secure good results in the prevention of accidents, it is generally recognized that the desire for such accomplishment, as well as the aggressive and constructive action to achieve it, must emanate from the Top Management and permeate successively down through the "Chart of Authority" to the workmen. Several years ago, with the above as a basis and with full support of the Top Management, the Mining Department started a program of selling the foremen and bosses the idea that safety could be achieved and that it was desired and required. Using psychology, persistence and numerous other methods, the foremen and bosses were finally impressed with the idea that "It can be done" and "It will be done." With this in mind, new ideas were brought forth by the foremen and bosses regarding the caving operation and the specific jobs in the operation. These new ideas were taken up in round-table discussions and resulted in certain changes in the undercutting method and the actual drawing of the blocks. These changes resulted in increasing fragmentation of the blocks which prevented the usual hang-up areas in the blocks. With the rock smaller in size and within reasonable reach from the tapping drifts, accidents were prevented in the tapping section. At the same time, an enforced campaign of housekeeping throughout the mine was undertaken with very beneficial results. The foremen and bosses then, in turn, educated and trained the workers themselves to become safely conscious. In so doing, a constant re- minder was given on all jobs assigned that the job was to be done safely as well as efficiently. No man is assigned a job who is not qualified for the type of work required. Efficiency and safety go hand in hand.

Jan 1, 1949

By P. W. Andrews, R. B. Toombs

ECONOMIC STRUCTURE OF MODERN INDUSTRIAL ECONOMIES The role of minerals in modern industrial economies may be examined in several ways. There are relationships with the various sectors of the economy: the primary, secondary, and tertiary industrial groupings and activities. Mineral supply and demand activities can be measured in terms of national accounts criteria. The economic policy objectives of the modem industrial economy are based to a considerable extent on the needs of the nation for economic supplies of miner- al materials. There is an important role for minerals relative to national security in peace and in wartime and many national policies are directed toward ensuring adequate sup- plies of minerals. Environmental control in the modem industrial economy is increasingly concerned with matters related directly to the production and use of minerals and these matters, in turn, bear importantly on conservation in mineral supply and demand. Mineral polices include specific provision for research and development activities concerned with the production and the use of minerals. In all, national policy objectives will be shaped in considerable part by the circum- stances of mineral supply and demand: the relative degree of availability from domestic and foreign sources, the state of the mineral-processing industries, and the degree of development of the mineral-using industries, and per capita and total changes in requirements. Goods made from mineral raw materials are the basis of all advanced societies and although this is taken for granted, every country is continually dealing with problems of mineral supply and demand. Considering that in the first 50 years of this century the consumption of mineral materials in a highly Industrialized country such as the United States increased by six times while the population was doubling, it becomes apparent that if a country is to enjoy rapid economic growth it must have access to huge and ever-growing supplies of mineral materials at lowest possible cost. Adequate supplies of mineral materials and wise usage of mineral resources have always been among the most important determents of a nation's survival The importance of access to adequate mineral supplies is increasing every year and this has significant international, as well as national, implications because of the unique locational characteristics of mineral resources. It is generally acknowledged that no particular type of natural resource is essential to a high level of national income or to economic progress. A country's endowment of natural resources need not exercise a determining influence on the course of its national income over time, provided it is able to trade. What is required for economic progress is the availability of a substantial quanti-

Jan 1, 1976

By R. C. Gifkins, K. U. Snowden

The value of the index n in power ktivs for the stress sensitivity of minimum creep rale at lead is derived front results drawn from lite literature and from previously unpublished nork on commercial (99.99 pel) and high-purity (99.999 pel) lead polycryslalline and hi crystal specimens. In tests al 0.5Tm (22 to 50'C) for slvesses below 250 psi, n fulls to mily for poly-cr,yslullirle specimens, single crystals, and bicrystals, and toy grain boundary sliding in bicrystals. Between 250 and 500 psi there is a tyansilion range and, for the polycrystalline specimens al least, u high-stress regime for 500 to 1500 psi where n is 5 or 6. These results are such that none of the suggested stress taws can he used to extrapolate to very loir stresses. Meclianisms for deformation in Ike grains and toy grain boundary sliding in the low-strcss regime are outlined. In particular, the mechanism for grain boundary sliding involves sliding controlled by diffusion from tensile to compressire Ledges. predictions based on this model give promising numerical agree-nicul with experiment. II is suggested that the mechanism for grain boundary sliding may he important in other circumstances, e.g., in creep of ceramic materials or superplaslicity, because it can operate with lille or no dislocation aclirity. WhEN the stress dependence of secondary creep rate is represented by a power law the values taken by the stress exponent n are found to vary between 1 and 7, see, c.g., Garofalo.' In Eq. 1 11 u is the applied stress and A a constant. The case for accepting values of v = 1 rests principally upon tests at high temperatures (>0.9Tm) and there have only been isolated tests at lower temperatures (rather than plots of creep rate against stress) for which the creep rates are such that some form of Nabarro-Herring creep with n = 1 is applicable. Hanson5 and Greenwood and cole6 plotted creep rate against stress for tests made in the vicinity of 0.5Tw, and found a "creep yield", so that below a certain low stress the creep rate was linearly related to stress: these observations appear to have been subsequently ignored. Various models have been proposed which agree with a large body of experimental results in which n equals -5 at high stresses (e.g., weertman7 and McLean8). Various alternatives to Eq. [1] have been proposed principally as a means of unifying creep data, but sometimes, it seems, in order to obviate the necessity for assuming a series of regimes of deformation associated with the various values of n; further refer- ence to these will be made in the section on stress laws. This paper calls attention to extensive results which show n = 1 for the creep of lead at room temperature (0.5 T,). RESULTS Fig. 1 is a composite diagram based on figures in the literature6,9,10 with additional results obtained by the present authors and their colleagues11,12 in the course of a number of investigations not directly concerned with stress sensitivity. In Fig. 1 In creep rate is plotted against In stress. The curves show results for two kinds of material. Lead I is of commercial purity (99.99 pct Pb) and lead IT a specially refined material, hydrogen-purified to remove oxygen; it contains 99.999 pct Pb. Curve A is for lead I in polycrystalline form (grain diameter 0.02 to 0.05 cm) at room temperature (22' to 26°C). Curve B1 is for lead I, polycrystalline, tested at 50C. Curve B2 is for lead 11, polycrystalline (grain diameter 0.02 cm), tested at room temperature (22 O- Curves C to F relate to tests made of bicrystals of lead 11: all of the same nominal orientation ("Y" in Ref. 12). Curves C and V are for creep within the component crystals of the bi crystals at 22°C (AB and CD in Fig. 2). Curve E is for creep measured in a gage straddling the boundary, approximately 0.15 mm either side (BC in Fig. 2). Curve F shows rates of grain boundary sliding (as distinct from strain rates in the other curves), obtained by averaging the offsets of six marker lines on the bi-crystal boundaries. The principal feature of the results is that the stress sensitivity falls into two distinct regimes, according to whether the stress is below approximately 250 or above 500 psi (there is a transitional range between 250 and 500 psi). The new result is that below -250 psi two of the curves (A and BI) give a value of n 1, and the other curves also drop below n - 2 to -1.5 but do not extend to low enough stresses to show clear evidence of n 1. At very high stresses the curves tend to give values of n - 6, as previously determined in other investigations. Curve R2 for the high-purity lead in polycrystalline form at room tenlperature almost merges with B, and thus gives new significance to the values for stresses of 150 and 200 psi; previously'3 these points had seemed to fall away from the curve of slope -3, but they now can be seen as almost completing a transition to n = 1. It should be noted that there was originally considerable apparent scatter in the results for the high-purity lead. However, this was found to be associated with annealing conditions or variations in residual content of oxygen and curve B2 was constructed using the highest rate (i .e., the rate for the purest lead) determined for each stress during the course of various investigations over the years: altogether, some forty tests were used in constructing curve R2.

Jan 1, 1968