Search Documents

By Fred P. Dewey

The product of the Muirkirk, Md., furnace has always enjoyed a very high reputation for strength ; and this is supported not only by its behavior in practice, both alone and in mixtures, but also by the following series of tensile tests, made at various times during the last fourteen years: South Boston Iron Co., November loth, 1874. Strength. Pounds Grade. per square inch. Density. No. 3,....... 30,685 7.2794 No. 4,....... 35,140 7.2713

Jan 1, 1889

By Harry L. Washburn, Robert L. Llewellyn, W. J. Halvorsen

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment. JUSTIFICATION FOR COAL PREPARATION During the past decade, major changes have occurred affecting the market, profit, and long-range planning of the coal industry. Mining companies have become "partners" with consumers at many new and some old mines, both for steam and metallurgical coals. Coal properties have become "assigned" tonnages at mutually agreed upon conditions and prices. Lower unit-train tariffs have been instrumental in helping coal markets to compete against oil and nuclear energy. Coal prices for power plants are still on a Btu (British thermal unit)

Jan 1, 1981

By Hiram B. Woon

Uranium ore deposits in the Lisbon Valley area are in an arcuate belt, 15 miles long by one-half-mile wide, on the southwest flank of the Lisbon Valley anticline. They range in size from 500 to 1,500,000 tons and by mid-1965 had yielded 6,147,000 tons containing 48,530,000 pounds of U3O8. Ore bodies average 6 feet thick, are tabular, amoeba-shaped masses, concordant to the bedding, and are in the thickest, lowest sandstone unit of the Moss Back Member of the Chinle Formation of Triassic age. The host rock is predominantly a fluviatile, calcareous, fine-grained to conglomeratic sandstone. Uraninite, the principal ore mineral, fills the pores in the sandstone and partly replaces sand grains and fossil wood fragments. During Late Permian and Early Triassic time pre-Chinle Formations were arched to form the ancestral Permian anticline. Moss Back streams truncated Moenkopi and Cutler beds which capped the ancestral anticline and then covered it with fluviatile elastics, which were subsequently covered by thousands of feet of Triassic, Jurassic, and Cretaceous sediments. Uranium, probably derived from the Chinle Formation by diagenetic processes, was transported in connate ground waters, was moved by compaction or hydrostatic forces, and was deposited under reducing conditions. Uranium was emplaced around the crest of the ancestral anticline, prior to the Laramide orogeny. During the orogeny, the Tertiary-Lisbon valley anticline was super induced on the Permian anticline and, penecontemporaneous with uplift, was faulted parallel to its longitudinal axis. The Big Indian ore belt on the southwest flank footwall block was elevated to approximately its present position, and the northeast flank hanging wall block was elevated only slightly. An extension of the Big Indian ore belt around the northeast flank of the ancestral Permian anticline may exist in the Moss Back sandstone in the downthrown block northeast of the Lisbon Valley fault.

Jan 1, 1968

By David J. Dunn

At a time when mill availability is at a premium, production costs are rising, and lead time for mill liner casting is a year or more, mill liner design is an important factor in ore grinding. Testing and selection of the optimum liner profile for a given set of mill operating conditions can improve mill capacity, reduce liner wear rate, and lengthen liner life. The mill liner that grinds best, lasts the longest, and costs the least is a necessity for economic mill operation. After testing four mill liner profiles for 3.96 X 3.65-m (13 x 12-ft) overflow ball mills, Climax Molybdenum Co. found that an improved design increased mill tonnage by 2.72 t/h (3 stph) while reducing finish grind by 1.7% minus 100-mesh, reduced liner wear rate, and almost doubled liner life.

Jan 12, 1976

By F. O. Garrabrant

Power is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are so designed that with the addition of forced cooling their capacity may be increased 33? per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 Per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200-amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches. Mine Power at 13.8 kv. enters the mine through a ventilation raise over a three-conductor, size 1-0 varnished cambric insulated, leaded, steel-wire armored cable, insulated from 17 kv. This power is received and distributed through one switching station and four underground substations, shown in Fig. 2. No. 370 substation (Fig. 3) contains three a 13,800/440-volt, single- phase Pyranol transformers protected on the high-voltage side by a 600-amp. manually operated oil circuit breaker. This station serves 20 slusher-hoist motors, a 45-kw., three-phase, 220-volt electric furnace, a Massco hot miller for tempering and milling Timken detachable bits and a hoist with 175-hp motor on the No, 3 development shaft. Also at this shaft are three pumps. One two-stage pump, 1200 gal, per min., 500-ft. head, 3600 r.p.m., driven by a 150-hp. motor, is at the bottom of the shaft, Two deep-well pumps, 500 gal. per min., 500-ft. head, are at the collar of the shaft. under normal operation the one pumping 1200 gal. per min, is controlled by a float switch to take care of the water. If this pump fails, or if its capacity is insufficient, the first 500-gal. pump is automatically started1 and if still more capacity is needed the second 500-gal. pump automatically starts. Time delay relays are provided on the deep-well pumps, so that if power fails the column will have time to drain before the Pumps restart. On failure of any Of these, an alarm is sounded in the train dispatcher's office, so that mechanics can be sent to ascertain the cause of failure and make repairs. The cable from No. 37' substation is run to the switching station, in which are four 15-kv., 600-amp. direct-current sole-noid-operated oil circuit breakers. The current for Operating and tripping is furnished by a 125-volt storage battery. All breakers are operated from the switchboard in the compressor room. One circuit from this switching station goes to the

Jan 1, 1946

By Zay Jeffries

HOSTILITIES in Europe, Asia, and northern Africa were responsible for dislocations in rare-metal supplies during 1940. Although the consumption of some of the rare metals is small the dislocations may be relatively large. In some cases these are advantageous to North America and in others they are disadvantageous. Specific instances will be cited later. Barium T HIN films of barium metal on special steel balls greatly improve the life and reduce the friction of rotating anodes in highly evacuated small X-ray tubes and make possible the operation of these anodes at relatively high temperatures. These remarkable results are described in an article by Atlee, Wilson, and Filmer in the Journal of Applied Physics for September, 1940. Oil could not be used because of the high temperatures on the one hand and its volatility on the other. Fig. 3 shows diagramatically the rotating anode and the method of coating the steel balls with barium. The letters K.I.C. refer to "Kemet Iron Clad." The K.I.C. wire was mounted so that the barium could be evaporated by direct passage of the electric current. At high temperatures the barium dif-

Jan 1, 1941

By A. D. Fernie

Growing interest in pit crushing and conveying is evident from the recent many articles, technical papers, and new equipment development. Application of a pit crushing and conveying system is complex. Many factors, such as mine design, production scheduling, as well as initial and ongoing capital and operating costs must be thoroughly and realistically examined. This paper will address the fundamentals to be considered and review several approaches to developing a total system for a new and existing mine situation. The planning function will be outlined and operating and design criteria defined to interface the mining operation and the pit crushing conveying system.

Jan 1, 1986

By J. A. Roberson, Robert A. Rapp

From the observation of platinum wire marker movement in the oxidation of columbium at high lemperatures and low oxygen pressures, predonzinant cation diffusion in CbO, has been demonstrated. The Cu,0 molecule was used as an oxidizing species to study the nature of the porous scale and the location of the reduction site in the oxidation of colum-bium. The Cb205 scale contains microporosity and forms by alternate ionic diffusional growth and fracture. The oxidation of columbium at high temperatures and very low po, results in a relatively compact and protective Cb205 layer. THE observation of marker movements during oxidation is one means for the identification of the mobile ionic species in an oxide lattice. Previous marker experiments in the oxidation of columbium have all resulted in the markers being found on the outside surface of the Cbz05 scale. The Cr203 powder markers of Klopp et a1.,' the gold film marker of Kofstad and ~jijllesdal,' and the platinum wire marker of Cathcart et a1 .3 were found at the oxide/gas interface for oxidation temperatures ranging from 450" to 120O0C. However, in all experiments relatively high oxygen pressures were used. As discussed by Mrowec, even the interpretation of marker experiments in simple scales containing only one compound is not without ambiguities. In brief, it can be said that a marker may be found almost anywhere in the scale layer if the metal oxidizes by cation diffusion through the scale; the position of the marker depends upon morphological happenings in the scale. When considering marker movement in a polyphase scale one must proceed with extreme caution. For example, in the past (and present) work markers have never been found at the columbium-scale interface, and one might infer that the oxygen ion is mobile in CbO and CbO,. However, only trace quantities of CbO and CbOz have been present on any of the specimens, so no firm statement is justified on this basis. Despite previous experimental work, considerable doubt still exists concerning the role of the oxides CbO and CbOz in the oxidation of columbium. The identification of the mobile ionic species in CbO and CbOz from the observation of platinum wire markers was one goal of the present investigation . The linear kinetics of columbium oxidation at high temperatures (T - 1000°C) suggests that the Cbz05 scales which form on columbium are porous. From mercury absorption measurements on a Cbz05 scale formed at 500"C, Aylmore et al.' reported a minimum volume fraction of connected voids equal to 0.15. While these scales often appear to be quite porous when viewed in metallographic cross section, they are so brittle that metallographic preparation is likely to exaggerate any porosity originally present. In this investigation, porosity developed during the oxidation of pure columbium and present at the high temperature was detected by oxidizing specimens in sealed evacuated capsules containing large compacts of mixed copper and CuzO powders. wooda has demonstrated that the CuzO, or (CuzO),, molecule is volatile and that oxygen is transferred by the CuzO molecule from a Cu/CuzO mixture to materials having a greater affinity for oxygen. For each molecule of CuzO that is reduced at a sink for oxygen, two atoms of copper are deposited. Quantitatively, essentially all of the oxidation carried out by a Cu-Cu20 compact results from a displacement reaction involving the CuzO molecule. When a metal which oxidizes to form a porous scale is exposed to the CuzO vapor, the CUZO molecules are reduced in the pores leaving a deposit of metallic copper to mark the site of the reduction. This technique has the rather unique advantage that any copper-coated pores found in the scale are unambiguously related to the reduction site in the growth of the scale under consideration. Pores or cracks which form in a msition*- external to the reduction site or which occur as a result of cooling or handling of the specimen will not exhibit the copper deposit. EXPERIMENTAL PROCEDURE Marker experiments were made on columbium metal, and on pellets of CbO which had been pressed and sintered. Platinum wire markers (0.001 and

Jan 1, 1968

By J. M. Woodall

GuAs crystals which have been grown in quartz boats by the horizontal Bridgman method in the pvesence of Ga20 vapov have beetz found to have carrier and donor distributions which do not correspound to those expected from simple dopant seg-vegation during directional freezing; Instead, the carrier distribution is determined by the heat-trentnzent history of the crystal, while the donor distribution, zohiclz is principally due to silicon, is fixed by the pozuth rate, the geo)tlet.ry of the crystal growth vessel, and tlze initial Ga20 pressure. WHEN semiconducting materials are made into doped crystals by the normal freezing method,&apos; they usually exhibit doping variations along the growth axis. If a) there is no dopant diffusion in the solid, b) the dopant is distributed uniformly in the melt, and c) the distribution coefficient, k, does not vary with composition, then the doping variation along the growth axis is represented by the equation: where C is the doping level in the solid at a point where a fraction g of the original liquid has frozen, and Co is the mean concentration. When the dopant is either a singly ionized shallow donor or shallow acceptor, C also represents the carrier concentration. Even though this equation accurately describes the dcping profiles of a large number of normal freeze systems, there are several special systems for which Eq. [I] does not apply. One such system is the horizontal Bridgman method for preparing oxygen-grown GaAs crystals using quartz vessels. Several workers2"* have shown that GaAs crystals grown by the horizontal Bridglnan method using quartz vessels are generally contaminated with silicon in concentrations in excess of 5 < 10lG atoms per cu cm. This contamination is ascribed to a reaction: occurring at the walls of the crystal-growth vessel which liberates silicon into the melt and Ga2O vapor. It has been shown4 that this reaction, and, hence, the silicon contamination, can be suppressed by the addition of oxygen to the crystal-growth apparatus. It is the purpose of this paper to describe a special apparatus capable of yielding single crystals of GaAs grown in the presence of oxygen and to describe both the kinetics of silicon suppression in this system and the relationship between the carrier concentration profile and the silicon concentration profile. EXPERIMENTAL-CRYSTAL GROWTH A schematic diagram of the apparatus used in the oxygen addition experiments is shown in Fig. 1. The most important features of this apparatus are: a) the use of a sand blasted quartz boat, h) a quartz rod of length 1, with a hole of cross section A, that is placed near the boat to limit the free space volume V, over the melt during the growth, and c) the temperature gradient at and near the solid-liquid interface. Sand blasting the boat is necessary to prevent wetting of the melt. The quartz rod retards the diffusion of the GazO vapor away from the melt to the colder portions of the ampoule. A crystal is prepared by first loading a 5.5-in. boat, which has been cleaned in aqua regia, with 40 g of 99.9999 pct Ga along with 1 to 8 mg of Ga203 powder. GazO3 is a convenient source of oxygen since it reacts with gallium at the melt temperature to form Ga20 vapor, the species which apparently controls the suppression of silicon contamination. The loaded boat, the quartz rod, and the 99.9999 pct As are placed in the ampoule as shown in Fig. 1. Generally, GaAs seeds were not used since most of the unseeded growths resulted in monocrys-tals. The ampoule is evacuated to 10-5 Torr and sealed off. The GaAs melt is synthesized by placing the ampoule into a two-zone horizontal Bridgman furnace. The two zones are separated by several sandwiched layers of -in. Fibre-Fax board drilled with holes slightly larger than the OD of the ampoule. This causes a very large temperature gradient between the two zones, which is necessary for single-crystal growth. The two-zone furnace is mounted on a stand fitted with a roller bearing which allows uniform motion of the furnace in a horizontal direction. A uniform velocity of the stand is achieved by the use of a windlass device which winds up a wire attached to the stand. Movement of the solid-liquid interface is accomplished by fixing the position of the ampoule and moving the stand. Growth rates investigated in this experiment were between 0.4 and 1.2 in. per hr. The composition of the melt is fixed by maintaining an arsenic reservoir at 618°C. The stand is moved away

Jan 1, 1968

By Henry Mulryan

THE largest and purest known deposit of diatomite is being actively mined and processed 3 ½ miles south of Lompoc, Santa Barbara County, Calif., by the Johns-Manville Products Corporation. The workings FIG. 1-LOCATION OF DIATOMITE DEPOSIT AT LOMPOC. cover 4000 acres, the depth of economically recoverable diatomite being 1000 ft. (Fig. 1). Lompoc, a community of 2500 population, is situated in the Santa Ynez River Valley 10 miles inland from the Pacific Ocean. It is 44 miles

Jan 1, 1936

By Arnold S. Epstein

Tlze green electroluminescence occurring at liquid-nitvogen temperature in epitaxial gallium phosphide diodes is exarnined using the donor dopants silicon and sulfur. Zinc is used as the p-type diffusant. Two tt~ain peaks are found, namely til 0.56 and 0.535 p. The intensity of the gYeen peak occurring at 0.56 is found to oary as -4"&apos; wlzere Jf is the forward current density and to first order appears to be dependent on the concet~tvation of ionized donovs. Tile vadintive lifetinze fov this process is -10-&apos;sec. The intensity of the 0.56-p lu~ninescence is nt least several ovdevs of magnitude greate,, at liquid-nitvogen temperature than that noted jor the 0.538 radiation for current densities up to about 35 amp per sq cm. The variation oj- the intensity of. the 0.538-p peak with current density caries according to the donor dopant. With sulfur as the donor one has a J12 dependence, whereas when silicon is the donov a J1.5 dependence is noted. Tl~e above can be fitted to a In molecular process (in first order) such as a band to band recombination. The constant B fir band to band vecombination) is found from our experitt~etlt to be of the order of 2 CZI cm per sec, zcl~ereas for tlze impurity vecombination peak (0.56 p]) tile A cotzstor~t is of the order of. 7 x 10-&apos; cu cm per sec. The structuve o/. the diodes at liquid-nitvog-en tett~peruture is oj tlze double injection type, and by carefi~lly selecting. the thickness of the structure one can regulate the onset of the 0.538-p radiation. The diode clzavaclevistics follow an I-Vx laiv where x is >1. Llregatiue resistance in these structures con be correlated with saturation of tlze 0.56- peak. ThE development of high-purity, large single crystals of epitaxially grown gallium phosphide is the ultimate aim of the studies to be reported. While a number of papers and reviews&apos; have been presented on properties of gallium phosphide grown from gallium solution and from the melt, less attention has been paid to the properties of epitaxial gallium phosphide grown from the vapor. In the studies to be reported we have examined the effects of shallow donor impurities, primarily silicon and sulfur, at liquid-nitrogen temperature, on both the electrical and green electroluminescent properties of carefully characterized single-crystal epitaxial Gap. I) EXPERIMENTAL PROCEDURES A) Material Preparation and Properties. The samules used in this investigation were single-crystal n-type epitaxial gallium phosphide. he single crystals were synthesized from the elements by vapor transport and epitaxial deposition on single-crystal gallium arsenide substrates. Typical transport agents used were chlorides. The growth procedures are described in more detail in Ref. 2. The samples were grown in the (111) orientation and had thicknesses up to 480 . Following the growth, the GaAs substrate was removed from the epitaxial Gap by etching in nitric acid. The Hall effect and resistivity of these n-type samples were measured as a function of temperature and analyzed for impurity content and compared with spectroscopic emission analysis. The results are given in greater detail in Ref. 3 but a summary is noted in Table I. In Table I, AED denotes the donor ionization energy, Nd is the donor impurity concentration, lvA is the acceptor impurity concentration, NI is the total impurity concentration, Rip vs temperature is the measured Hall mobility-temperature relationship from liquid nitrogen to about 400"K, n(77"K) is the measured carrier concentration at liquid nitrogen, and R/p(77&apos;~) is the measured Hall mobility at liquid nitrogen. Good agreement is noted between electrical and emission analysis for the major donor impurity, silicon, in the two materials where it is a major constituent. In the case of the two samples SC90-6 and AP138-3(111) B which were sulfur-doped the ionization energy found from the electrical data is in good agreement with that reported for sulfur.4 The acceptor impurities are not known, although from the presence of magnesium in the samples as indicated by emission analysis and its known role as an acceptor in GaP,4 magnesium could be present as an acceptor. Similarly, since silicon is known to be an amphoteric impurity4 it may also be present as an acceptor in the Gap.* The *A small band has been noted at 0.625 11 in samples SC90-6, SC76-4, and SC77-4, suggesting according to Ref. 5 that sillcon could be present as an acceptor In these samples since these authors have found this peak to represent a donor-silicon emission. presence of calcium deduced from emission analysis is not correlatable with the electrical analysis and its presence as an electrically active impurity should be questioned. B) Sample Preparation and Diode Fabrication. The original slices were of the order of 2 sq cm in area witi the (111)B face up. The material was cleaved and sectioned and the best pieces selected (i.e., those which visually appeared to have the least strain and defects). The samples were polished, lightly etched, and cleaned in trichloroethylene. Zinc was diffused in a closed tube at 800°C to form a p-n junction. Diodes were made from these samples. The depth of junction varied, but did not exceed 10 p depth. The back side of the slice was lapped back and a low-resistance n-type contact was formed (at 600°C in forming gas) to an Au-Mo tab with a hole in the middle for

Jan 1, 1968

By Arthur F. L. Bell

Prior to 1908 the oil production in the State of California had been almost entirely a heavy fuel oil, with a high flash point, but changed within a short period to a large percentage of refining oil with a low flash, by reason of the heavy production of light oil coming in from the Santa Maria field, the Midway field, and the increased production of the Fullerton field. This is clearly shown in the following tabulation of California&apos;s pro- The bringing in of these high percentages of light oil with their dangerous low flash and the increasing demand for the refined products necessitated the devising of some cheap and efficient means of quickly separating the lighter elements either in the field or at the main distributing points; also it became necessary to remove the excessive percentage of water which many of the light oils carried in emulsion. Union Oil Co. Port Harford Plant Probably the first important attempt to top light oil in California by other means than the ordinary stills was tried about 1908 by the Union Oil Co., at its plant at Port Harford, San Luis Obispo County, with Santa Maria oils. The process was the invention of Hubert G. Burroughs who afterward obtained a patent for the process, No. 998,837, dated July 25, 1911. The apparatus used consisted of a series of 12-in. pipes mounted in units of three pipes, one above the other, the crude oil being admitted to the upper pipe and filling it about two-thirds of its

Jan 1, 1916

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1939 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. TECHNICAL PUBLICATIONS in Classes A-Metal Mining, B-Milling and Concen-tration, H-Industrial Minerals, and ;I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Technical Publications in Classes C-Iron. and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. TECHNICAL PUBLICATIONS in Class G-Petroleum Division are distributed in PETRO-LEUM TECHNOLOGY, which is issued quarterly. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administra-tion, and L-Geophysical Methods of Exploration are issued as separate pamphlets. An Institute member is entitled to one copy of any TECHNICAL PUBLICATION or CON-TRIBUTION. Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute according to their registration by classes. CONTRIBUTIONS and Other TECHNICAL PUBLICATIONS will be sent upon request. A member relay purchase an additional copy of a TECHNICAL PUBLICATION Or a CONTRIBUTION at One cent a page; minimum charge, 25¢. Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION Of the F, J, K, or L classes at the same rate, but the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1. TECHNICAL PUBLICATIONS (separate pamphlet form), $2 per annum; Canadian and foreign postage 50 cents extra. METALS TECHNOLOGY, $7 per annum; Canadian and foreign postage 50 cents extra (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers). MINING TECHNOLOGY, $6 per annum; Canadian and foreign postage 50 cents extra (metal mining, milling and concentration, Industrial Minerals Division, and mining geology papers). PETROLEUM TECHNOLOGY, $4 per annum; Canadian and foreign postage 50 cents extra. Bound volumes have been mailed to members that have requested them, and MINING AND METALLURGY is mailed each month. A member is entitled to one volume a year on his membership and lie may purchase for $2.50 one copy of a volume not already received; additional copies of &apos;the same volume, $5. Nonmembers may pur-chase the volumes listed, at $5 each, plus 60 cents for Canadian or foreign postage. Extra single copies of MINING AND METALLURGY, 25¢ current issue, back numbers 500 each to members; to nonmembers 50¢ current issue and $1 each, back issues. Subscription price to nonmembers and to members for extra copies, $3 per annum plus $1 for Canadian or foreign postage.

Jan 1, 1939

By Robert L. Llewellyn

Preparation of coal begins at the face in underground mines or in the pit with surface mines. Impurities in raw coal can be in the seam itself or in extraneous material taken in mining from the roof or bottom. Raw coal is prepared only to the extent that is necessary to make the product salable. Over 60% of all coal production is processed to some extent in cleaning plants. For underground mines the proportion cleaned is 72% as compared to 42% from surface and 15% from auger mines. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only as necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent and only incidently with mines shipping raw run-of-mine coal crushed to a top size of, usually, 2 to 4 in., with little, if any, other treatment. ECONOMICS OF COAL PREPARATION During the past decade, major changes have occurred affecting the market, profit, and long-rang planning of the coal industry. Mining companies have become "partners" with consumers at many new and some old mines, both for steam and metallurgical coals. Coal properties have become "assigned" tonnages at mutually agreed upon conditions and prices. Lower unit-train tariffs have been instrumental in helping coal markets to compete against oil and atomic energy. Cod prices for power plants are still on a Btu (British thermal unit) basis but with more emphasis on sulfur content. For metallurgical coal, the lower and medium volatile coals are in demand and the price rises, generally, as the volatile percentage is lower. Moisture affects the Btu value of coal almost the same as ash content, but dusty conditions during loading and unloading are no longer accept-

Jan 1, 1973

By J. W. Clark, C. T. Sims

Wrought chromium-base alloys containing yttrium, cubic monocarbides of the Ti(Zr)C type, and similay alloys containing manganese and rhenium have been melted and fabricated. Strength has been studied by hot hardness and elevated-temperature tensile and rupture measurements, low-temperature ductility by tensile testing, and surface stability by oxidation testing. In additiod, studies have been conducted of the carbide stability, and of aging behavior. The carbide dispersion generates effective elevated-temperature strength, which is further enhanced hv strain-induced precipitation. The dispersion exhibits classical dissolution and aging response. The ductile-to-brittle transition temperature of these alloys is above room temperature. The alloys reported show fairly good oxidation resistance, but nitrogen contamination can cause fortnation of a hard Cr2N layer under the oxide scale. Manganese does not appear to be a promising alloying element in chromium. In the years 1945 to 1950, the metal chromium was considered as a possible base for alloy systems due to its considerably higher melting point than superalloys, its low density, its high thermal conductivity, and its apparent capacity for strengthening. However, this interest in chromium was short-lived. It was found difficult to melt and cast, to be exceptionally sensitive to the effect of minor imperfections, to have a lack of ductility at both room and elevated temperatures, and to be subject to a deleterious effect of alloying elements upon the ductile-to-brittle transition temperature.&apos; Since then, chromium, as a practical alloy base, has remained virtually unstudied. Further, purposeful ignoring of chromium has been promoted by statements that its bcc structure would not allow it to be strengthened to useful values, when compared to the "austenitic" alloys.2 Recently, a new look has been taken at chromium-base alloy systems. Study of the literature will show that chromium, providing some of its disadvantages could be eliminated or minimized, actually has a rather attractive potential as an alloy-system base. Analysis of rather scattered data suggests that chromium is quite capable of being strengthened to high levels. Also, significant strengthening of its two sister elements in Group VI-A, molybdenum and tungsten, has been demonstrated in a number of commercial and exploratory alloys. Chromium should be similar. Since chromium does not readily form a volatile oxide like tungsten or molybdenum, it offers a much higher probability of giving birth to alloy systems with useful oxidation resistance. Concerns about possible high elemental vapor pressure have been mitigated by recent data.3 In addition, the physical properties exhibited by chromium are attractive for application as a high-temperature structural material. For instance, its thermal conductivity varies from 49 to 36 Btu-ft/hr-sq ft-°F over its range of usefulness (which is two to four times higher than most superalloys), its density is about 7.2 g per cc (20 pct less than most nickel-base alloys), its coefficient of thermal expansion varies from 4 to 8 x 10-6 per OF, and it has a relatively high modulus of elasticity, approximately 42 x 10&apos; psi.4 Alloying studies on a chromium base in the past have usually encompassed rather sweeping solid-solution alloy additions for strengthening. This is not consistent with contemporary alloying practice in Group VI-A. For instance, molybdenum, also in Group VI-A, is primarily alloyed for strength improvement by use of heat-treatable carbide dispersions.5 Chromium and molybdenum are similar in their chemical activity and other properties. Thus, strengthening of chromium by carbide dispersions was studied. Chromium-base alloys are plagued with room-temperature brittleness, although high-purity unal-loyed chromium can be made ductile.4,8 Use of yttrium as a scavenger has done much to improve ductility and resistance to nitrogen embrittlement in chromium systems,7 so it was utilized in this program. It has also recently been found8 that small rhenium additions (1 to 5 pct) create improvement in the ductility of Type 218 tungsten wire. This is apparently related to the remarkable effect of rhenium additions near its terminal solid solubility in all Group VI-A metals.9&apos;10 Investigation to establish if dilute concentrations of rhenium would also be effective in chromium appeared to be logical for this program. Since rhenium is too expensive to be practical in alloys for application as structural components, ductility improvements through solid-solution alloying were also sought by substitution of manganese for rhenium; manganese, like rhenium, exists in Group VII of the periodic system. The optimum amount of carbide dispersion for chromium-base alloys was obtained by analogy with molybdenum. Strengthening in molybdenum is achieved by use of Ti-Zr carbide dispersions. A

Jan 1, 1964

By James E. York

AT a meeting of the American Society for Testing Materials at Atlantic City, June, 1908, Dr.. C. B. Dudley, in his presidential address,&apos; showed the vital necessity of not only making a steel rail as good as in the past, but of making it considerably better in order to meet the present and prospective require¬ments of railroads. Doctor Dudley requested the co-operation of all who from personal experience could give information that would result in bringing about the production of a steel rail that could be relied upon to meet the present requirements. I have had considerable experience in the practical manufacture of steel of almost every grade, during the past 40 years, and I shall suggest changes that will bring about the results desired. Doctor Dudley has had a long experience as chemical and metallurgical expert for the Pennsylvania railroad, but he frankly admits that up to the present time both he and other metallurgical experts lack the practical knowledge of steel-making that is necessary to state correctly the reasons for the unreliability of the steel rails now produced. The necessity is self-evident for more positive practical knowledge on the part of these experts of what is possible and what is impossible regarding the practical manufacturing of steel rails from the ingot to the, finished product. Chemical knowledge in steel-making is far in advance of what it was years ago, and might be said to cover every requirement (in that department) for producing reliable steel. The study of the metallography of steel has been of great value, also the physical testing of steel, but this knowledge will only de-

May 1, 1909

By Å. Sterten, R. Tunold, J. Brun, K. Dalatun

c axis compression behavior of beryllium single crystals at three purity levels under hydrostatic pressures up to 27 kbars was determined. Extensive non-basal slip, observed by two-surface trace analysis and transmission electron microscopy, occurred under a hydrostatic pressure of about 12 kbars (175 ksi) for the high-purity (twelve-zone pass) material and at about 19 kbar (275 ksi) for the lower-purity (zone-leveled) material. Prismatic loops with a (c + a) Burgers vector were observed in association with second-phase parti- A principal factor limiting the use of beryllium is its brittle behavior when tested at the usual strain rates (E = 10-4 sec- 1) at temperatures below about 200°C and under impact conditions at temperatures in excess of 200°C. It has been proposed&apos; that the brittle-ness of beryllium is associated with the lack of a sufficient number of independent slip modes and the absence of a slip mode with a Burgers vector out of the basal plane [presumably (c + a) pyramidal slip mode] and to the ease with which beryllium cleaves on the basal and second-order prism planes. The absence of pyramidal slip has been attributed to a high Peierls-Nabarro stress associated with the motion of dislocations with a (c + a) vector and the ease with which cleavage occurs on the basal and second-order prism planes. The experimental evidence in support of the proposed explanation for the brittleness of beryllium is far from complete; for example, that the ductile-to-brittle transition in polycrystalline beryllium is associated with the operation of profuse (C + a) slip has not been unequivocally established. The occurrence of (c + a) slip ({1122}(1123)) has been experimentally established2-5 under conditions where basal and prism cleavage are restricted in a c axis compression test. In these investigations (C +a) slip was found in high-purity beryllium single crystals tested in c axis compression* at 200°C and in Be-4.4 pct Cu and Be-5.2 pct cles in the lower-purity materials tested. The loops were related to surface "extrusions" observed on many of these same specimens. Nonbasal dislocations operating on (1122) planes with a (c + a) Burgers vector were observed. The presence of c and a dislocations together with (c + a) dislocations suggests that the (c + a) dislocations dissociate presumably on unloading or after failure of the test crystals to c and a dislocations. terial, (c + a) slip has only been observed near the the fracture4 surface in room-temperature c axis compression tests. Fracture in these tests occurs without measurable plastic flow, as determined with a strain sensitivity of 10"6. Since it has been shown for many metals that the application of hydrostatic pressure suppresses fracture,?-&apos; it was felt that studying the behavior of unalloyed beryllium single crystals stressed in c axis compression under a hydrostatic pressure would reveal whether (c + a) can occur if fracture was prevented, and that it might elucidate the role of (c + a) slip in the ductile to brittle transition. Evidence that (C + a) slip is associated with increased ductility in a high-pressure environment has been found in stress-strain tests on poly crystalline beryllium.10 The present paper describes a study on the influence of a hydrostatic pressure environment on the occurrence of (c + a) slip in beryllium single crystals. Material of two purity levels was tested in c axis compression over the pressure range ambient to about 27.5 kbars.* 1) MATERIAL PREPARATION AND CHARACTERIZATION Two lots of low-purity single-crystal beryllium were used. The first lot was "ingot secondary refined grade" and designated lot A. The second lot (lot B) was produced by a two floating zone pass zone-leveling operation in an argon-filled sealed quartz apparatus on a 1-in.-diam by 12-in.-long bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. The high-purity material (lot C) was made by traversing twelve floating zone passes through a similar bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. In a series of spark cutting and lapping procedures,11 single-. crystal specimens some 0.12 in. sq by 0.30 in. high were made with the sides Parallel to the first- and second-order prism planes and the basal plane within 3&apos; of arc of the top and bottom surfaces of the specimen. Such an accurate orientation is necessary because of the large difference in resolved shear stress

Jan 1, 1970

By R. W. Raymond

The absence of a convenient glossary- of terms connected with mining and metallurgy has long been felt by the general public. It is to meet this want, not to furnish a technical manual for experts, that the following glossary has been prepared. It originated in an attempt on my part to revise for publication the manuscript of a compilation prepared from the appendix of Yale&apos;s work on Mining Titles and one or two other sources, to serve as an appendix to a new work on mining law, about to be published by Mr. H. N. Copy, of Washington, D. C. This revision soon assumed, contrary to my original intention, the proportions of a reconstruction; and with the consent of Mr. Copp, and for the purpose of receiving from my fellow-members valuable aid, I presented my still incomplete work as a paper at the Lake Superior meeting of the Institute, inviting from any quarter suggestions of new terms or better definitions to be incorporated in the glossary before its final publication. This invitation was so widely and generously responded to, that I cannot undertake to make in this place individual acknowledgments to those members of the Institute, and professional colleagues outside of it, who have favored me with assistance and advice. The labor bestowed upon this paper since its presentation at the Lake Superior meeting has considerably exceeded that of its first preparation, as

Jan 1, 1881

By Paul R. La Pointe

GEOTECHNICAL OBJECTIVES OF UCG PROGRAM Underground coal gasification (UCG) is one of several in situ extraction technologies for utilizing deep, otherwise unmineable coal. This technology involves the injection of air or oxygen into the target coal seam, ignition of the coal and recovery of product gases. Geotechnical characteristics of the coal and enclosing rock strata strongly influence the success of this Process. The flame front follows the coal cleats (Hill, 1979), and cleating and bedding control the manner in which coal collapses into the cavity, thereby affecting recovery efficiency (Ramirez and others, 1982). Moreover, coal seams typically behave as fracture dominated aquifers in which cleat orientations govern subsequent contaminant dispersal. For these reasons, the Anaconda Minerals Co. undertook a detailed study of fracturing within the Wyodak-Anderson Coal in the eastern Powder River Basin (PRB) near its Rocky Hill UCG test site (Fig. 1). STRESS HISTORY AND FRACTURING IN THE POWDER RIVER BASIN Vertical jointing, or cleating, in coals may arise from shrinkage shortly after deposition under low confining pressures, or later in time, soon after burial but after the coalification process is well advanced (Ting, 1977). There is much evidence to support the formation of cleating after coalification (e.g. Hawkes and Mellor, 1970; McCulloch and others, 1974), which suggests that the stress state existing at that time strongly influences cleat formation. McCulloch and others (1974) argue that the typically better developed face cleat forms parallel to the plane containing [ol] and [o2]. Where the relation between cleats and stess has been studied (McCulloch and others, 1974; Stone and Snoeberger, 1977; Ward, 1977; Kulander and Dean, 1978), the highly systematic face cleat strongly parallels the [o1] direction. Stone and Snoeberger (1977) report face and butt cleat measurements of N70E and N29W for the Felix Coals 220 m stratigraphically above the Wyodak at the Hoe Creek UCG site (Fig. 1). Structural trends also indicate the past state of stress in the PRB. Glaze and Keller (1963) suggest that the NE-SW regional compression during the late Permian formed major N-S fold lines and basement magnetic anomalies. Mapel (1959) describes folds having N60W and N30W rends in the northern PRB, as well as a large normal fault trending northeast. Glass (1976) also describes normal faults trending northeast. Similarly, Olive (1957) mapped normal faults

Jan 1, 1984

By E. E. Donath

Application of the coal hydrogenation process for the production of chemicals is described. It has been estimated that a plant to produce 31,090 bbl per day of chemicals and fuels would cost $326,- 000,000. These products would consist of 6.1 pct by weight tar acids, 50.8 pct aroma tics, 16.4 pct LPG, and 26.7 pct gasoline. THE coal hydrogenation process is well known as a means for the production of liquid fuels from coal. In this paper the possibilities of the coal hydrogenation process as a source of chemical raw materials will be discussed. The recovery of chemicals from coal hydrogenation products necessitates some modifications and additions to the equipment used for the production of fuels. The conversion of coal into liquid fuels such as gasoline requires two steps: liquid phase and vapor phase hydrogenation. Intermediate oils obtained in the liquid phase contain oxygen and nitrogen compounds, especially aromatic compounds, since the coal itself is composed mainly of cyclic compounds. These oils are the raw material for the separation of high molecular weight aro-matics and of tar acids and tar bases. The relative amounts of heavy and middle oil—boiling above and below, e.g., 325°C—can be influenced by temperature, residence time, and catalyst of the liquid phase hydrogenation. In the vapor phase hydrogenation a solid bed catalyst is used to convert the intermediate oil from the liquid phase operation into hydrocarbons of the gasoline boiling range. Essentially pure hydrocarbons with a low content of sulphur, oxygen, nitrogen, and olefines are obtained. Depending mainly on the catalyst, the high ring compound content of the liquid phase oil can be preserved and gasoline rich in aromatics obtained. However, with other catalysts, these ring compounds can be split into gasoline with a high content of isoparaffins.&apos; Again, depending on the operating conditions, products of varying boiling range can be obtained. Selection of catalyst and operating conditions therefore makes possible the production of different grades of motor fuel and also variations in the relative amounts of benzene, toluene, and xylene when aromatic hydrocarbons are produced. The schematic flowsheet, Fig. 1, shows the main steps of the coal hydrogenation process, and the product streams used for the recovery of chemicals are indicated. In the liquid phase hydrogenation stage, coal is made into a paste with recycle heavy oil. The coal paste is mixed with hydrogen and preheated at a pressure of 300 to 700 atm in heat exchangers and preheaters. The coal paste and hydrogen enter high pressure converters where the liquefaction of coal, conversion of the high boiling liquid materials initially obtained, into intermediate oils is performed at a temperature around 470°C. The reaction products enter the hot catchpot in which lower boiling oil vapors are separated from the residue containing unreacted coal, ash, and heavy oil. This residue, usually called H.O.L.D. (heavy oil let down), is processed to separate solid and liquid material. By thermal treatment of the residue, e.g., a coking process, distillate oil is obtained, which can be recycled as part of the pasting oil. This stream is rich in polynuclear aromatics and can be, and has been, used for the recovery of such material. The oil vapors and hydrogen from the hot catchpot are cooled in heat exchangers and a cooler, and the condensed oil is separated from the recycle hy-

Jan 1, 1953