Search Documents

By Takaaki Ishikawa

The distribution equilibria of lead, zinc and copper between CaO-Si02-Ah03 melts and liquid copper were measured at 1623K under a controlled H2-C02 atmosphere. The distribution ratios were plotted against the oxygen partial pressure, and reasonable oxide forms dissolved in the melts were estimated from the slopes of the plots. The activity coefficients of zinc oxide (ZnO), lead oxide (PbO) and cuprous oxide (CuOQs) increased with increasing slag basicity, defined by Xcao /XSiO, The temperature dependence of the activity coefficients was also measured.

Jan 1, 2003

By Mariane Costalonga de Aguiar, Carlos Mauricio Fontes Vieira, Sergio Neves Monteiro

"This work evaluates the effect of incorporation of an ornamental rock waste into an industrial clayey body used for roofing tiles fabrication. Formulations with 0, 10, 20 and 30 wt.% of waste were prepared by replacing the sand in the industrial clayey body. The plasticity of the formulations was determined by the Atterberg limits. Specimens were fabricated by 18 MPa press-molding and then fired from 850, 950 and 1050°C. The specimens were tested to determine the water absorption, linear shrinkage and three points bending flexural strength. The results indicated that the waste improves the extrusion performance of the clayey body by decreasing its plasticity. The use of the waste was beneficial to the water absorption and mechanical strength of the fired clayey ceramic at 1050°C.IntroductionOrnamental rock is a natural resource available in the municipal area of Santo Antonio de Padua and located 150 km from the city of Campos dos Goytacazes, northe of state of Rio de Janeiro, Brazil. Intense industrial activity related to ornamental stones, especially gneisses, is traditionally occurring in the region. After mining, the flagstone is submitted to sawing to obtain blocks and then, after a manual operation, the final products are small flagstones [1,2]. During the sawing operation, a sludge composed of water and fine particles of rock is generated. A monthly production of 1000 tons of ornamental rock waste is estimated to be produced at Santo Antonio de Padua. The final disposal of this waste has brought serious environmental problems. Since most industries do not have an adequate sludge treatment, the waste is contaminating the soil and underground waters as well as obstructing rivers and lakes.Ceramic bodies industrially fabricated in the municipal area of Campos dos Goytacazes, 280 km from the city of Rio de Janeiro, are still empirically elaborated using a mixture of local clays. These clays are predominantly kaolinitic mineral, associated with high plasticity. Due to the excessive plasticity of the ceramic bodies, it is common to have dimensional defects in the final products after the drying and firing processes. Moreover, the kaolinitic structure and the presence of aluminum hydroxide confer a refractory behavior to the local clays. This impairs sintering during the firing operation. In the case of clay ceramics for civil construction, this results in greater porosity associated with elevated values of water absorption [3,4]. To avoid this problem, it is necessary to reformulate the ceramic body composition. The addition of both non-plastic materials to reduce plasticity and fluxes to condition the refractoriness is a possible alternative."

Jan 1, 2011

By D. A. Horne, V. R. Daiga

Certain steel mill wastes contain significant amounts of zinc oxide due to the use of galvanized scrap during the steel making process. Typically electric arc furnace (EAF), and basic oxygen process (BOP) flue dusts contain 20 to 30% zinc oxide and 40 to 50% iron oxides, along with smaller quantities of lead and cadmium. These materials can be recovered from the flue dusts by using a proven rotary hearth furnace (RHF) process. By-products of the recycling operation include a crude zinc oxide fume, which is captured in a baghouse filtering system, and sponge iron that may be recycled into the steel making operation. Crude zinc oxide properties plus the operating experience from two commercial RHF installations utilizing MR&E's DRyIron™ Process will be presented.

Jan 1, 2000

By Hector M. Henao

The FeOX-CaO-SiO2 base slag at intermediate oxygen partial pressures is very often used in non-ferrous smelting processes. This slag would also contain Al2O3 and MgO because these compounds are normal components in the ore and the refractory of a furnace. The objective of the present work is to determine the effect of Al2O3 or MgO addition on the liquidus temperatures of the plain FeOX-CaO-SiO2 slags in the atmosphere between intermediate pO2 of 10-6 and that of iron saturation at 1250 and 1300 °C. The experiments were carried out at given mass%CaO/(mass%CaO+mass%SiO2) ratios ranging from 0 to 1 and at spinel-tridimite double saturation. The experimental results show that the effect of Al2O3 or MgO addition on the plain FeOX-SiO2-CaO slag is not uniform and depends on the content of Al2O3 or MgO, the oxygen partial pressure and the mass% CaO/mass% SiO2 ratio. It is apparent that Al2O3 or MgO addition enlarges the spinel or wustite saturation area at almost all the oxygen partial pressures and temperatures of this research. The obtained phase diagrams will be useful in the metallurgical industry to assist in the selection of slag chemistry, operation condition and development of new processes.

Jan 1, 2006

By K. Murayama, M. Kawakami, T. Takenaka, S. Yokoyama

"Cokes play an important role of spacer in blast furnace. However, they degenerate during Boudouard reaction. Blast furnace cokes are reacted with pure C02 at I 072 to 1673 K. Reaction rate was obtained by the weight change of spherical specimen. The specimen after reaction was examined by microscopic observation. The reaction rate increased with temperature and was expressed by two Arrhenius type lines. The activation energy was 126 KJ/mol at higher temperature than 13 73 K and 202 KJ/mol at lower temperature range. At the higher temperature range, the reaction proceeded from the surface leaving unreacted core, whereas homogeneously whole inside at lower temperature. The porosity increased from the center to surface at higher temperature, whereas it was almost constant at lower temperature.IntroductionThe cokes have the function of fuel, reductant and spacer to keep gas and liquid flow in the blast furnace. Thus, the reaction mechanism of coke with several gas and the strength after the reaction should be important factor to control the blast furnace operation. The reaction mechanism of coke with C02 has been studied extensively. The rate equations were derived by Gadsby[ I], Ergun[2] and Turkdogan and Vinters[3]. They were compared and discussed by Kobayashi and Omori [ 4]. Effect of crystallization degree on the reaction rate was examined by Kashiwaya and Ishii[5]. Catalytic enhancement effect of ash componets have been clarified by Kashiwaya et. al. [6]. Although degradation of coke in blast furnace has been examined recently[7], however, the degradation of coke after the reaction with C02 has not been well clarified yet. In the present work, the metallurgical coke specimen was heated in N2 and C02 and the reaction mechanism and degradation behavior after the reaction was investigated."

Jan 1, 2000

By Aiyuan Ma, Kun Yang, Weiheng Chen, Jinhui Peng, Shiwei Li, Feng Xie, Libo Zhang

In this thesis, a new process of recovering zinc sulfide ores was developed. The novel synthetic coordination leaching process mainly included two steps: microwave assisted phase reconstruction and compound coordination leaching. By applying various techniques, such as chemical composition analysis, X-ray diffractometry (XRD) and Raman spectroscopy, it could be concluded that sulfide phases would directly oxidized to zinc oxides under the 500 ºC microwave roasting and adding 30% Na2O2. What’s more, zinc leaching rate reached to 61.16% within 2 hours. Compared to the current technologies, this procedure had the advantage of avoiding SO2 emission, high leaching efficiency, simple process, manipulate easily, and low cost, which could be expected tremendous application potentials.

Jan 1, 2016

By T. Ueno

Naoshima Smelter & Refinery of Mitsubishi Materials Crop. commissioned a new Mitsubishi continuous copper smelter in May 1991. Process offgas volume of the conventional reverberatory furnace line, one of the previous smelters having been shut down, was very large and thus two acid plants had been operated. It was expected that the offgas volume would, be reduced at the new smelter to about a half of the sum of those from previous two smelters and the sulfur dioxide strength would be increased. So various alternatives were studied to minimize the operation cost. And it was decided to utilize both of the plants with minor modifications by diluting the gas either with air or with dilute gases. The acid plants now receive off gases from the new copper smelter, a sintering machine of a lead smelter and a decomposer of waste acid. The paper discusses plant design, operation, improvements and modifications realized in relation with the retrofitting of the copper smelter.

Jan 1, 1992

By Masao Miyake, Eiichiro Matsubara, Tetsuji Hirato, Yasuhiro Awakura

"Zn-Cr alloy coating with around 15 wt% Cr has been found to have much higher chemical corrosion-resistance to steel than conventional zinc plating, while· its structure has not been clarified. The Zn-Cr alloy plating is performed at high current densities around 1 A cm-2 and for 10 to 20 sec using acidic aqueous sulfate solutions with some additives in the iron-steel industry. Due to the high current densities, it seems reasonable to consider that the Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings have a non-equilibrium phase and have a structure change in the .direction of thickness. In this research, the crystal structure of the Zn-Cr alloy coating electrodeposited at high current densities and change of the structure in the direction of thickness were examined by X-ray diffraction. The coatings containing under 20 and 35-40 wt% Cr had hcp and bee structure, respectively, while the coatings containing 20-35 wt% Cr comprised two phases with the hcp and the bee structure. The structure of the coating varied in the direction of thickness; both the hcp and bcc phases coexisted in the vicinity of the substrate, while the hcp phase became predominant with increasing distance from the substrate.IntroductionRecently it has been reported that Zn-Cr alloy coating containing around 15 wt% Cr has much higher corrosion-resistance to steel than conventional zinc plating.1-3) The corrosion-resistanc·e of Zn-Cr alloy plated steel sheet with a plating amount of 20 g m·2 is, for example, superior to that of Zn plated steel with a plating amount in the range 60 to 90 g m·2 , which is widely used for automotive bodies today.4l The Zn-Cr alloy plating is obtained by electrodeposition at current densities over 0.5 A cm·2 from a sulfate solution containing zinc and trivalent chromium ions and some additives.5•6) The deposition current densities mentioned above are much higher than those for usual electroplating processes, e.g., Zn, Cu and Ni plating, carried out about 0.05 A cm·2 • Therefore, the time required for plating is very short; around 10-20 sec. Due to the high current densities, it seems reasonable to consider that the· Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings do not have a phase expected from equilibrium diagrams; no phase diagram of the Zn-Cr system with a full composition range has been available. 7). In other words, the alloy phase plated would be a non-equilibrium phase with unknown structures."

Jan 1, 2000

By Ki Joo Sim, Sung Beom An, Joonho Lee, Minsoo Shin

Valorization of the electrical arc furnace oxidizing slag by coke was carried out by the reduction of iron oxide in the slag. Since the reduction of iron oxide by solid carbon is an endothermic reaction, supply of heat energy is required. In addition, slag has a low thermal conductivity; traditional fuel injection is not suitable for this reaction. Microwave can be used to supply heat energy to the system. Commercial oxidizing slag was reduced by coke under the microwave irradiation (1.7 kW, 2.45 GHz). The maximum recovery ratio of iron was 87%. In addition, slag composition modification was attempted to use the remaining slag for a mixture in cement clinker. Free-CaO in the slag was successfully suppressed, and the use of the remaining slag as a potential mixture was confirmed.

Jan 1, 2014

By Anand Kumar, Pradeep kumar Jha, Suman Kant, Pradeep Kumar

"It has been a major challenge to reduce the intermixed grade formation during ladle change-over operation in continuous casting process of tundish steelmaking. The F-curve generated by step input of the tracer (new grade steel) tells about the intermixed grade amount for different grade specifications. Use of flow modifiers is beneficial in reducing the intermixed grade because of the change in slope (in different time zones) and position of the F-curve due to their placement at tundish bottom. Present study aims at investigating the role of dam placed before the outlet in a multi-strand tundish with reference to the slope behavior of F-curve in different time zones during the teeming operation plays an important role in determining the intermixed amount.Introduction In Continuous casting process, the old grade steel remaining in the tundish (reservoir between ladle and mould) from the old ladle gets mixed with new grade steel from new ladle and leads to intermixed grade which is considered to be of inferior quality. Although formation of intermixed grade is inevitable with the sequential method of casting, its amount can be controlled by changing the flow behavior of steel inside the steel. Intermixing in a slab caster tundish was simulated using 3-D numerical model based on k-å turbulence equation and compared their result with that of water model experiment Yeh and Hwang [1]. Huang and Thomas [2] reported that quantity of residual fluid in tundish affects the composition distribution in the transitional slab and thus the intermixed length. Huang and Thomas [3] developed three sub models to predict mixing in tundish, liquid core of strand and solidification. Thomas [4] developed a one dimensional model to simulate the final composition distributions in slab caster of continuous casting and investigated the effect of process variables on the intermixing. Alizadeh mehdi et al., [5] simulated of the intermixing phenomenon for slab casting for three different sub models. Goldschmidt et al. [6] developed a numerical model that predicted the location of the intermixed steel in a four line round caster. Lan and Khodadadi [7] studied for the transient fluid flow of liquid steel, heat transfer and solidification during the flying tundish change process. Cho and Kim [8] developed a mixing model to predict the outlet concentration of the tundish during grade transition. Most of the work reported in the literature has dealt with intermixing in slab caster tundish. Billet caster units are more often being used by steel industries due to growing demand of billets. The multiple outlets lead to varying degree of intermixing with time owing to their different distance (location) from the inlet. Use of flow modifier to minimize the intermixed amount, however has also not been discussed in detail so far. Further no work has been reported regarding effect of slope of F-curves obtained through different outlets on intermixing. Hence keeping these objectives in mind attempt has been made by authors to analyze the slope of Fcurves after dividing them into three different time zones and the effect of these time zones on intermixing."

Jan 1, 2012

By Leonard J. Friedman

The recovery of sulfur dioxide from metallurgical gases for the production of sulfuric acid has been an effective means of reducing sulfur dioxide emissions from non-ferrous smelters. Sulfuric acid has been produced from gas originating from fluid bed roasters, electric furnaces, reverberatory furnaces, flash smelting furnaces, Pierce Smith and flash converters, sinter machines, etc. The gas from each of these sources has a unique set of variables that affect the design and operation of the sulfuric acid plant. In addition, the sulfuric acid plant itself has been evolving, with new equipment designs and materials. This paper will review each of the unit operations in the gas cleaning and contact sections of the metallurgical sulfuric acid plant, discussing various equipment designs, materials and the handling of gas stream variables and impurities. The paper updates to 2006 previous works on metallurgical sulfuric acid plants by the authors.

Jan 1, 2006

By Youn-Bae Kang, Jong-Jin Pak, Min-Kyu Paek

The critical evaluation and thermodynamic optimization of Mn-Si-C and its sub-binary systems have been carried out over the whole composition range from room temperature to above the liquidus temperature. The solution properties of the liquid systems have not been clearly described because the liquid solution exhibits a high degree of short-range-ordering. In order to predict the thermodynamics of the liquid solution, the liquid phases were optimized by the modified quasichemical model. The model parameters of the solid phases were also optimized by the compound energy formalism to best reproduce the phase diagram and important thermodynamic properties in Mn-Si-C system. Using the model parameters, various thermodynamic calculations were carried out. The present database will be a part of larger thermodynamic database for the ferromanganese alloy database.

Jan 1, 2014

By Lv Guozhi, Niu Liping, Liu Yan, Zhang Zhiqi, He Jicheng, Zhang Ting’an, Dou Zhihe

"CuCr alloy can be extensively used as contact materials in integrated circuit, electrodes, electric contact and high strength conductor. We proposed thermit reduction-electroslag remelting method of preparing the large scale CuCr alloy. But there are pores and oxide inclusions in CuCr alloy prepared by thermit reduction process. This paper studied mainly the effects of ratio of reactant and additive on the inclusion type and their occurrences in CuCr alloy. The slags and CuCr alloy were characterized respectively by XRD and SEM. The results show that when the additive is Na3AlF6, the slag consist of Al2O3 and Cr. When the additive is CaF2, the slag consist of Al2O3, Cr, CaF2 and CaAl4O7. The inclusions in CuCr alloy are mainly Al2O3 and pores which disperse in Cu-rich zone and Cu-Cr phase interface. When 5% CaF2 and 5% KClO3 are added, there are fewer pores and inclusions, and the more better microstructure.1 IntroduceCuCr alloy is the contact terminal material with an eximious properties[1,2], which gradually replaces CuBi alloy becoming the first choice for contact terminal material in the medium and high power vacuum switch after the 1970s. The traditional preparation methods of CuCr alloy mainly contain powder metallurgy, infiltration process and vacuum electric arc melting methods. But the above methods exist some shortcomings, such as poor product quality, high cost of production, processes complex ect[3-9]. CuCr alloy is made by the thermit reduction self-propagating method, which uses CuO, Cr2O3 and Al as raw material to get the high-temperature melt, and then casts to manufacture CuCr alloy ingot, which response equation follows as:"

Jan 1, 2012

By Mikiya Tanaka, Mikio Kobayashi, Mansour A. S. A1Ghamdi, Kenji Tatsumi, Yukinori Saiki, Hirotaka Senba

"In order to recover nickel ion in a spent electroless nickel - phosphorus alloy plating bath and, at the same time, to remove impurities such as iron and zinc, the applicability of solvent extraction with LlX84I as the extractant has been investigated using actual spent solution. Although the extraction efficiency of nickel from the spent solution is considerably lower than that from the nickel sulfate-nitrate solution, nickel in the spent solution is selectively extracted with high efficiency at the pH of 6 - 7. The extracted nickel is effectively stripped by sulfuric acid at a pH of less .than· 3. On the basis of these results, a· flowsheet for recovering nickel from the spent solution is proposed Chemical equilibrium calculations of the spent solution has shown that the complex formations of nickel with anions such as lactate and phosphonate ions become predominant in the pH range between 2 and 6. This results in the depression of nickel extraction efficiency from the spent solution as compared with that from the .nickel sulfate-nitrate solution. By combining these aqueous equilibrium calculations with the· extraction model considering the extraction stoichiometry and the aggregation of the extractant in the organic phase, the extraction behavior of nickel is quantitatively predicted.IntroductionElectroless plating is indispensable for the recent advanced industries such as the electronic and mechanical industries. Electroless plating baths are repeatedly used by supplying the metal salts; however, the accumulation of the counter anions of the metal ions, the components formed by the oxidation of the reducing reagents in the plating baths, and the metal ions as impurities dissolved from the surface of the objective materials degrades the· quality of the plating. Thus, the baths are finally treated by a precipitation method to form a large amount of metal sludge, which is disposed in dumping sites. Therefore, from the standpoints of environmental protection and resource preservation, it is highly desired to establish a recycling process of the plating baths with minimum emission. Solvent extraction seems to be one of the 'suitable methods to recover metals from the spent electroless plating baths, because the concentration of the metal ion in the baths is relatively high, which is advantageous to solvent extraction as compared with the ion-exchange and adsorption methods. Some studies about the application of solvent extraction have already been carried out using simulated spe11t electroless plating baths [1-3]."

Jan 1, 2000

By Chuanhong Li, Zuohua Lin, Zhancheng Guo

"Catalytic mechanism of CeO2 in combustion of coals was investigated in this paper. Catalytic combustion of four kinds of coals with different metamorphic grades by CeO2 was examined, suggesting that catalytic function of CeO2 increases with increase of metamorphic grade of the coals. One important reason for CeO2 promoting combustion of the coals is that pyrolysis of anthracite is advanced by CeO2, which not only raises the pyrolysis rate and pyrolysis conversion ratio, but increases contents of light components in pyrolysis gas; and both pore space and specific surface area of the pyrolysis char are enlarged by CeO2, which is another reason. In order to realize in situ catalysis for reducing catalyst consumption, it is crucial to increase catalyst particle number and enhance the bonding force between catalyst and coal. In addition, remarkable energy saving effect was observed when a nanometer calcium-based rare earth catalyst obtained by hydro-thermal synthesis was applied to catalytic combustion of coal injection into blast furnace.Introduction Coal combustion is acknowledged as one of the most important coal applications. Since addition of catalysts could reduce the ignition temperature of pulverized coal and accelerate the coal combustion, catalytic combustion is generally accepted as an effective measure to realize fast combustion of coal. Furthermore, different catalysts added may produce different effects on ignition temperature of coal. It is reported activity of catalysts with the same cation follows this order: OH->CO3 2->Cl->SO4 2-; while that of the catalysts which have the same anion follows: Cs+>Rb+>K+>Na+>Ba2+>Li+>Sr2+>Ca2+>Mg2+>Be2+ [1-4] .Due to the special physical and chemical structure, CeO2 plays an important role in the catalysis field. Many literatures point out that CeO2 not only has great catalytic effect on energy conversion, succeeded in catalyzing combustion of gaseous fuels such as CH4, CO, etc. but also can catalyze combustion of some liquid and solid fuels such as JP-10, black carbon, carbon deposit in the automobile exhausts and so on [5-9].Pyrolysis, the first step of combustion, directly influences ignition temperature and combustion rate of coals. So a great variety of catalysts were applied to catalyze pyrolysis of coals. And plenty of studies suggest that the alkali and alkaline-earth metal compounds inherent in the coals show apparent catalytic effect on coal pyrolysis. Meanwhile, addition of alkali and alkaline-earth metals into coal combustion process also indicates obvious catalysis effect, accelerating coal pyrolysis, improving pyrolysis conversion ratio, increasing contents of pyrolysis gases and changing composition of the pyrolysis gases [10-15].Although alkali and alkaline-earth metal compounds have good catalysis effect on coal combustion, their application in the catalysis field was limited because of their erosive attack to the combustion equipments. In contrast, CeO2, as a substitution of the traditional coal catalysts, presents widely potential application due to its good catalysis ability, non-corrosive and nontoxic. However, investigation on CeO2 catalyzing coal combustion is rarely reported. In this work, catalytic mechanism of CeO2 in coal combustion was studied, in an attempt to provide theoretical foundation for developing new catalysis technologies."

Jan 1, 2009

By S. Neven

The smelting of copper anode slimes, a material which contains mostly lead, silver, copper and selenium, has been practiced for many years with a view to recovering the silver and associated small amounts of gold. However, a theoretical understanding of the process has been lacking and this handicaps efforts to improve and intensify smelting operations. In the past few years work has been done in this area and this work will be reviewed in the paper. The underlying thermodynamics of the oxidation of silver-copper selenide mattes has been developed and used as a basis for the construction of a computational thermodynamics model which attempts to predict the composition of all condensed phases during the course of smelting. The model will be outlined and its successes in matching experimental data, as well as its current deficiencies, will be considered. Supporting work on the thermodynamics of silver solubility in slags, on activity-composition relationships in the Ag-Se system and work in progress on the oxidation state of copper in the slags will be reviewed. These projects are designed to provide further detailed data which will improve the robustness of the thermodynamic model.

Jan 1, 1999

By J. G. Zafiratos

The leaching of a Greek low-grade manganese dioxide ore, not amenable to conventional mineral processing operations, was studied using a mixed culture of Thiobacillus sp. bacteria. The experiments were carried out in specially designed continuously aerated and stirred tank reactors arranged in two-tank series. The first tank of each series was loaded with an elemental sulfur culture suspension while the second was loaded with a manganese ore high density slurry. The bacterial culture had been previously adapted to grow on elemental sulfur and also in the presence of manganese ore and dissolved manganous ion. A two level full factorial design was constructed in order to study the effects of the ferric ion concentration in the leach solution, the "elemental sulfu weight to ore weight" ratio, the ore pulp density and the composition of the dispersed gas. The responses which were investigated included percentage manganese recovery, co-dissolution of iron and manganese dissolution rate. Parameters with constant values throughout the experiments were the leach solution pH, the nutrient medium composition, the dilution rate and the ore and sulfur grain sizes. It was found that the ferric ion concentration was the most significant factor and had a positive effect on the final percentage extraction of manganese from the ore and also on the rate of manganese solubilization from the ore. The effects of the other factors studied are discussed in detail.

Jan 1, 1997

By Dieter Wanner

Off-gas cleaning from metallurgical? plants, requires in many cases very low dust contents which are, difficult to achieve with conventional scrubbers, even with high energy input. Lurgi has developed a scrubber which improves the separation of the fine dust by electrical charge prior to the scrubbing zone,, An Electrostatic Scrubber has been successfully installed for the off-gas cleaning from slag granulation after a waelz kiln achieving less than l mg/m3 in the clean gas.

Jan 1, 1992

By D. Mishra

Electric arc furnace dust (EAFD) generated during the recycling of steel- scrap is classified as a hazardous waste for landfilling. This is because it contains leachable heavy metals such as zinc, lead,... Recovery of these metals could result in both resources conservation and resolving waste disposal problems. A study of the thermal reduction of a sample of EAFD was carried out in an inert gas atmosphere using coke as a reducing agent. Preferential volatilization of zinc and lead was achieved during the reduction process at about 800 "C. More than 96 % of both zinc and lead were removed from the dust and were recovered in the condensates. The treatment residue was essentially composed of iron oxides and almost free from heavy metals.

Jan 1, 2002

By R. M. Reynolds

Engitec Impianti, S?.p.A. of Milan, Italy has successfully designed, constructed and has in operation state-of-the-art battery breaker systems at two European locations. A third facility i:s partially completed in Toronto, Ontario, Canada. The CX system crushes whole batteries, separates the various components and desulfurizes the battery paste. The system also produces sodium sulfate from the sulfuric acid and lead sulfate contained in the batteries. Actual plant operating data indicates that the desulfurized paste contains less than 0. 6 percent sulfur and less than 0. 5 percent antimony. The CX system utilizes mechanical screening and an up-flow hydrodynamic separator to accomplish the component separation. Sodiwn hydroxide or sodium carbonate is used for desulfurization. The sodium sulfate brine is evaporated and crystallized to produce clean anhydrous sodium sulfate suitable for use by detergent or glass manufacturers. Plant data also indicates that an increase in furnace productivity of about 25 to 30 percent is achieved using feed from the CX system. The desulfurized paste is very suitable for electrolytic processing as an alternative to pyrometallurqical processing.

Jan 1, 1990