Search Documents

By Earle S. Burnett

Rotating piston deadweight gages have been used for many years for measurement of pressure to several hundred atmospheres. They have been calibrated by comparison of fluid pressures produced by various loads bearing on the piston bases, as measured by corresponding heights of balancing columns of mercury. When expressed in appropriate units, these ratios of column heights to piston loads are called piston constants. Experimental arrangements and procedures for their determination are presented in this paper, followed by a discussion of their significance and of their subsequent applications.

Jan 1, 1966

By Foster Fraas

Almost all minerals show irreversible changes in electrical conductivity after heating in the temperature range 100° to 800° C. This effect can be detected with only a limited number of minerals with the standard ionizing-electrode-type separator, which differentiates between nonconductors and conductors in the single-particle resistivity range of 1011 to 1013 ohms. Tests outside this range with other type separators, such as the static field type, increase the number of minerals with which the effect can be detected to almost all that were tested. Irreversibility may be the result of an alteration of adsorption layers, volatilization of surface cations or anions, or an oxidation or reduction. One example is limonite, which decomposes to hematite and passes through two minima and two maxima in conductivity in the temperature range 100° to 900° C.

Jan 1, 1959

By Martin Hertzberg

A comprehensive study of the flammability behavior of air-dispersed coal dust was made using an 8-liter Bureau of Mines system which included the following: (1) An optical probe to continuously monitor the dust concentration; (2) measurements of ignition energy requirements; (3) the use of several narrow size distributions ranging from 3 to 65 µm in average diameter; (4) measurements of the extent of flame propagation based on pressure attained at constant volume, residual O2 content after combustion, and flame and dust surface temperatures. The measured lean limit for near-horizontal propagation of Pittsburgh coal dust was about 135 mg/l (milligrams per liter), virtually independent of particle size. Required ignition energies were hundreds of joules and measured limit flame temperatures were 1,450 to 1,600° K. Data on inerting? requirements with KHC03, rock dust, and NaC1 gave approximately the same results as full-scale explosion tests. The good agreement suggests that the cause of earlier discrepancies between small-scale laboratory data and full-scale mine experiments may not have been the difference in size, but were rather a problem of proper care in isolating and controlling the significant experimental variables and in consistently defining the extent of flame propagation at the limits.

Jan 1, 1979

By V. R. Miller

The Bureau of Mines conducted research on substitute brazing filler alloys with properties similar to those of silver filler alloys in an effort to conserve silver and reduce hazards from cadmium emissions. Experimental work was conducted first on the commercial silver brazing alloys BAg-I, BAg-la, BAg-2, and BAg-3 to establish criteria for evalu-ating the substitute alloys. Properties investigated included the wettability of copper, brass, and steel substrates, and the strength of joints made with the filler alloys. A series of experimental alloys containing 50 to 60 pct Cu, 20 to 28 pct Mn, and 17 to 30 pct Zn was prepared and evaluated, together with Cu-Mn-Zn alloys with 5 pct Pb or 2 pct Ni. Wetting properties and joint strengths were not as good as those for silver filler alloys, and the high application temperatures reduced the copper and brass base metal strengths. However, experimental alloys containing 70 pct Cu, 15 to 20 pct Mn, and 10 to 16 pct Sn had wetting and strength properties approaching those of the silver filler alloys. The application temperatures for these alloys were high-er than those for silver fillers, but not as high as those for the Cu-Mn-Zn alloys. With the Cu-Mn-Sn alloy fillers, copper alloy joint members are less deteriorated by recrystallization than when applying Cu-Mn-Zn alloys. The Cu-Mn-Sn system has potential for further devel-opment as a substitute brazing alloy system, particularly if the melting temperature can be reduced by the addition of other elements without decreasing the ductility and wetting.

Jan 1, 1983

By Jay F. Colinet

Longwall mining in lower seam heights may necessitate the use of single-drum shearers to overcome size constraints associated with standard double-drum shearers. To avoid the operational problem of clearance in the tailgate entry with one single-drum shearer, two single-drum machines can be operated on the same face, with each shearer responsible for mining a predefined portion of the face. However, utilization of two shearers on the same face necessitates the positioning of one shearer operator and a jacksetter in the return air of the upwind shearer, thus complicating respirable dust control on the longwall. In an effort to evaluate the unique dust control problems associated with this type of mining, the U.S. Bureau of Mines conducted dust surveys on two multiple-machine longwall operations. Sampling was done to quantify major sources of respirable dust and to identify potential solutions to problem areas. Sampling results indicate that the cutting sequences utilized on multiple-machine faces may have to be designed to minimize dust exposure, as opposed to optimizing productivity or facilitating operational requirements. Also, state-of-the-art dust control techniques typically found on double-drum shearer longwalls must be employed to help minimize the exposure of all face personnel to traditional dust sources.

Jan 1, 2010

By Oliver Bowles

The various Latin American countries are undergoing a slow process of industrialization. The harvesting of one or two agricultural commodities or the mining of a few marketable minerals is being supplemented by development of an Integrated industrial economy. In many countries, progress in this direction has not been rapid, but as it gains impetus an increasing market for cement is a natural consequence. This is evident from the fact that industrialization is linked with increasing transportation, and means of transportation are very poor in much of Latin America. Bridges, culverts, and concrete Highway's, now scattered sparingly throughout the vast land areas south of the United States, must multiply as the demands of industry increase and as a higher scale of living is attained. Eventually the South American countries will be linked by modern highways. Furthermore, the arid climate of many regions creates a demand for construction of dams and irrigation works, and a continent poor in coal reserves but with abundant water power inevitably must direct its energies toward the construction of hydroelectric power plants. Countries rich in raw materials but with few natural harbors have urgent need of massive concrete breakwaters and docks. The demand for concrete in houses will also grow. Standards of living are low, and perishable building materials are widely used. As living conditions improve cement will be used increasingly in home construction. Even in the field of simple and modest housing cement affords a means of creating low-priced verminproof and fireproof homes, for which the need it imperative under climatic conditions that prevail in this area of the world. Already many of the countries have undertaken extensive public works, and such programs are likely to increase. Assuming moderate industrial progress and stabilized governments the demand for cement in this great southern area promises substantial growth.

Jan 1, 1940

By Ludwig Schmidt

Large quantities of gasoline are lost each year by evaporation from bulk-storage station tanks. The rate of evaporation from bulk-station tanks is influenced by two principal factors: First, the vapor pressure of the gasoline in the tank; and second, the amount of "breathing" of the tank. The vapor pressures of the gasoline govern the amount of the gasoline vapor in the air-vapor mixture above the gasoline in a tank at a given temperature. This is one of the principal factors in determining the total pressure of the air-vapor mixture within the tank. The "breathing" of the tank is caused by the inflow of air from the atmosphere during certain periods of the day and the expulsion of the air-vapor mixtures at other times, caused by atmospheric variations. The pressure built up within a tank and the amount of gasoline in the air-vapor mixture are both a direct function of the temperature existing within the tank. Therefore, two of the most common methods for reducing evaporation losses from bulk-station tanks are: (1) The use of vapor-tight tanks equipped with relief valves and operated at 1 or 2 ounces of pressure and about 1/2-ounce vacuum; (2) reducing the temperature of tanks and their contents by painting them a light color, by insulation, and in some instances by using water sprays. Water sprays, although effective, usually are too expensive to operate economically. In order to determine and compare the effects of various colors, insulation, and pressure in reducing the evaporation losses of gasoline held in storage in bulk-storage tanks, the Bureau of Mines made observations from May 29 to October 15. 1930, on five horizontal tanks of 12,000-gallon capacity each, which were erected at the plant of Black. Sivalls and Bryson Manufacturing Co., Kansas City, Mo. This report gives in detail the results of these evaporation tests.

Jan 1, 1931

By Clarence Karr

RESINS from a bituminous pitch, a bituminous coal, a lignite tar, a subbituminous pitch, and an electrode binder pitch wore investigated by the Bureau of Mines. The compositions of these resins were determined by four independent methods of structural detemination: (1) Molecular formula and ring analysis, including ring (2) infrared and ultraviolet spectra; (3) combined pyrolysis/gas chromatography, and (4) catalytic dehyrogenation followed by spectra and pyrolysis. The resin structure was correlated with coal structure, and it was concluded that pitch resins probably consist of essentially unaltered coal molecules carried over with the tar vapors in low-temperature carbonization.

Jan 1, 1966

By Wallace W. Roepke

Research to evaluate the lubricity effects achieved by spraying water on the cutting bit of a mining machine or spraying water on the coal during cutting has shown that neither practice affects cutting forces, as had been believed. However, when water was supplied to the cutting zone axially through the bit at 3,000 to 5,000 psi pressure, tangent'ial cutting forces were reduced an average of 30 pct at a I-in depth of cut while normal bit forces were reduced an average of 65 pct. Lower normal forces mean reduced bit wear, faster advance with greater depth of cut, and fewer coal fines.

Jan 1, 1985

By Robert S. Sanford

Intensive investigations of domestic manganese deposits were conducted by the Bureau of Mines and the Geological Survey during the earlier part of the war minerals investigations when there was doubt that the quantity of manganese needed to produce the greatly increased tonnage of steel demanded for war supplies could' to obtained from its customary sources. Domestic deposits of ores that contain sufficient manganese for direct production of ferromanganese essential in steel Manufacture are generally small, and the bulk of the supply is imported. One of the few large deposits of low-grade manganese ore known in the United States is in the Artillery Peale district in southern Mohave County, Ariz. Manganiforous sediments underlie a very large area. Several large groups of claims, covering the most of the manganese-bearing ground, wore assembled in 1929 and 1930. The greater part of this area was leased by the M. A. Hanna Co. in 1937. Investigations by engineers and geologists for this company revealed that the average content of manganese is very low; but that the Maggio Canyon area, about 180 acres, contains higher-grade material. The company put down 28 vertical diamond-drill holds to explore this ground, under the direction of B. N. Wobbor, geologist.

Jan 1, 1948

By Ginger S. Evans

This report documents a preliminary hydrologic investigation of an area where longwall mining methods are to be used. The scope of work includes: determination of physical and chemical characteristics of major soil types in the area; determination of physical and chemical properties of surface water bodies; collection of geologic characteristics, including stratigraphy, structure, and detailed aquifer descriptions; collection of 10 years' meteorological data and installation of a weather station; and a detailed ground-water investigation that includes completion of observation wells, aquifer testing, water quality sampling, and analysis using a 3-D computer model. The Trescott model developed by USGS was used to simulate steady-state aquifer conditions. Input data from 8 multiple-completion monitor wells were used to model an area of approximately 10 square miles. Two layers, coal and overburden, were simulated, both confined. Model results showed good agreement with know piezometric data, desaturated areas, and flow from springs. The study area was found to have very low-yield bedrock aquifers with transmissivities ranging from 5 to 320 ft2/day for the coal (depths from 500 to 1,200 ft) and from 499 to 576 ft2/day and fractured sandstone units (depths less than 100 ft). Annual precipitation and recharge are very low, 10 to 11 inches and 0.25 inch respectively. The area has very high relief and large areas of rock outcrop. No perennial streams are present on the site.

Jan 1, 1983

By F. E. Diebold

The methodology for describing the geochemistry of elements in a coal seam have been developed. This has been applied to the Rosebud Coal Seam, which is an economically important member of the subbituminous coals of the Fort Union Formation in Eastern Montana. The method development has involved a detailed study of two popular techniques for determining the metal geochemistry of coal, namely, whole coal analyses and coal physical fractionation. The mathematically contrived element associations (whole coal analyses technique) and the element concentration trends in the float and sink fractions (physical fractionation technique) are considered to lead to only qualitative conclusions concerning the chemical associations of the elements in coals. Additionally, the processes taking place with the coal during low temperature ashing in an oxygen plasma are experimentally investigated and shown to be of sufficeint extent that the use of such low temperature ash for deciphering element geochemistry is questionable. The method developed in this study is a chemical fractionation that involves the sequential leaching of coal with water, 0.5 N HC1, 3 N HC1, 2 N HNO3, and 48% HF. These leach solutions are shown to selectively dissolve the predominate inorganic phases, sulfates, Ca and Mg carbonates, Fe sulfides and K alumino-silicates and quartz, respectively. These phases were identified with the use of XRD, SEM, EM and leaches (water and 0.3 N HC1) of whole coal and low temperature ash. The incorporation of the anion-exchange step in the leaching scheme was investigated and was observed to warrant further study of such intensity to be, at the time, unuseable. The use of this sequential leaching technique on several coal samples from the same seam generates element concentration trends that can be quantitatively interpreted with respect to the chemical associations of the minor and trace metals in the coal seam. The properties of the various seams of economic importance in the Fort Union Formation in Eastern Montana are compiled and presented. The subsequent conclusion is that there is not a large variation in the properties of these coal seams and that the variations within the Rosebud are within one order of magnitude. The chemical fractionation technique, investigated in this study, was applied to composite tipple samples of the Rosebud seam. Each composite sample represented 76,800 tons of coal. A minimum of 32% of the Ca and Mg are present as separate water soluble sulfates. An excess of the sulfate ion in the water extracts shows the predominating influence of the ion exchange capacity of the organic compounds in the coal. Based upon the CO content of the coal and the HC1 leachate data, 25 to 30% of the alkaline earth elements exist as separate carbonates and the remainder are associated with the organic compounds. The small fraction of the illite that dissolves in the HC1 and HNO3 leachates accounts for the K and Al. Slight dissolution of the pyrite in the HCl solvent occurs, the small amounts of Li and As do not relate to any known phase and Mn is present as a separate carbonate phase. Fe and a significant amount of the As exist in the pyrite that is dissolved in the HNO. Se is equally partitioned between the pyrite and the organic compound~. Most of the trace elements are found in the HF solutions. Li, V, and Cr were interpreted to be associated with the clay minerals (kaolinite and illite). Ni and Pb appear to be present as separate phases and 50% of the Hg is HF soluble but is not chemically related to any known inorganic phase.

Jan 1, 1983

By Paul M. Tyler

A great variety of substance that differ widely in chemical, mineralogical, and physical properties are loosely linked under the generic term "clay", but for the average man all that matters is whether a given material can be sold or used profitably. So-called "clays" range in texture from true clays and allied minerals that are typically "fat" or sticky to fine sand. Sand and other strictly silicious materials, such as tripoli and diatomite, are not clays in any sense; but many commercial clays are strictly loams, for they are intermediate in texture and always contain a mixture of minerals, though the term "loam" has little commercial usage except in foundry work. Even pure kaolinite, ordinarily considered the typical "clay substance", recently was found to exist as three distinct minerals; and each of these, in turn, exhibits variations in particle size and other physical attributes. Probing with the X-ray and employing other modern tools and techniques, scientists are tracing the patterns of molecules and finding chemical and physical phenomena that seem to disclose the causes for the markedly different behavior of the various aluminum silicates with varying proportions of combined and adsorbed water that are the essential ingredients of commercial clays; but rule-of-thumb definitions and enforced reliance upon empirical tests of actual samples still hold sway. In addition to the hydrated simple silicates of aluminum, almost all clays contain quartz, feldspar, and mica with varying amounts of organic matter and, in addition, other impurities - such as iron, manganese, and titanium oxides - that may discolor them sufficiently to render them unfit for certain important uses. The white clays are generally the purest, but no two clays are really alike, and great care must be exercised to maintain a reasonable uniformity in successive shipments even from the same deposit.

Jan 1, 1938

By D. Harrington

Part III-B, presented in this circular, completes the series reviewing the literature on effects of breathing dusts with special reference to silicosis; it includes data on the status and cost of compensation for silicosis in the United States and several foreign countries and a summary and general conclusions covering the whole series. Parts I, II, and III-A of the series have been issued as Information Circulars 6935, 6840, 6948 , and 6957; Part I defines and classifies dusts, indicates sources of exposure, and describes the physiological effects of breathing dusts; Part II-A discusses the principal dust factors producing pulmonary pathology and methods of determination of dust in air; Part II-B presents data on the engineering and medical control in the prevention of dust diseases and general recommendations for their control in industry; and Part III-A deals with the economic and legal aspects of dust diseases in industry.

Jan 1, 1936

By R. M. Santmyers

Caesium, rubidium, and lithium are sometimes described as the minor or rarer alkali metals. They generally occur together in nature, although, lithium is distributed more widely and is far more abundant than either of the other two. The chemical, and even the physical, properties of these three elements can best be considered In conjunction with the more familiar members of the alkali group, sodium and potassium. The five elements lithium, sodium, potassium, rubidium, and caesium show an interesting gradation properties from member to member with the increase in atomic weights. All are silvery white and soft enough to be cut with a knife. They tarnish rapidly in air and decompose water at ordinary temperatures. The lowest temperature at which the action of the several metals on water can be de¬tected is -98°C. for sodium, -105°C, for potassium, 108°C. for rubidium, and -116°C. for caesium. The chemical activity appears to increase steadily from

Jan 1, 1930

By Effie T. Kurt, Jack Wright, J. W. Watkins, Cynthia Pearson

"The analysis of water produced with crude petroleum has interested oil producers since inception of the industry. Records of the first analysis of mineralized water produced from an oil-productive formation are obscure, and references to the first use of brine analyses to assist in solving problems of petroleum production are not available in the technical literature. However, many early reports of the Federal Bureau of Mines 5-8/ and. Federal Geological Survey, 9-11/ as well as articles in engineering and geological placed special emphasis on journals ,12-l4/ the importance, interpretation, and application of water analyses.One of the earliest applications of water analyses, and still a major one today, is for identification of intrusive waters in oil wells. This may be done by comparing the chemical constituents of a sample of water indigenous to the oil-productive formation with those of samples from upper, water-bearing formations within the same general area. Some earlier investigators recognized the need for analyzing samples of all waters encountered in drilling operations. Ambrose15/ stated, in part, ""In wells being drilled, the engineer should grasp every opportunity to get a true sample of water from each sand. . .,"" and, ""The waters of each oil field are chemically different from those of another field."" The validity of the latter observation and the importance of the former one have been borne out by comparing the results of analyses of many samples and noting the differences in relative concentrations of like constituents of waters from the same geological formation in different localities or oil pools."

Apr 1, 1957

By W. W. Staley

This paper discusses the design of small head frames that will fill the needs of prospectors and small operators whose operations are conducted through shafts. The head frames considered were designed to handle relatively small tonnages. It was assumed that the shafts in which buckets are used would not exceed 300 feet in depth and that not over 60 tons of rock would be hoisted, in, 14 hours. In the design of the larger head frames, a hoisting capacity of about 250 tons per 6 hours from a depth of 300 to 500 feet was assumed. Under these conditions, hoisting speed, rate of acceleration, and weight of rope have a negligible effect on the head frame design and, therefore, have been ignored in the following, discussion. Because timber is relatively cheap and easily obtained in most mining areas, the discussion has been confined to timber construction.

Jan 1, 1937

By A. B. Coates, J. E. Crawshaw

"The use of such methods and apparatus as the Dautriche method and the Mettegang recorder for the determination of the rate of burning of black blasting powder and other strictly burning explosives has been found to give such erratic results that no reliance can be placed on the data thus obtained. Consequently, investigators of those factors which may affect the burning rate, such as size of grain, absolute density, chemical composition, and means of ignition have had to rely mainly on observations made during practical use for determination of the part played by each. Such tests are very difficult of interpretation.The purpose of this paper is to describe a method used by the explosives division of the Bureau of Mines for the investigation of such explosives and to present the results of an investigation using that method.The investigation was concerned with the effect of grain size, initial pressure, and means of ignition on the rate of burning or rate of pressure development of black blasting powder as compared with pellet powder.The Bichel pressure gauge was used for these tests, with the slight modification to the apparatus and method described in U. S. Bureau of Mines Bulletin 15.4 These modifications consisted of reducing the speed of the revolving drum on which the time-pressure record is taken, measuring the speed of the drum by a belt-driven tachometer, and introducing an induction coil in series with the electric squib or electric detonator to mark on the time pressure record the instant at which the squib or detonator was fired."

May 1, 1929

By Charles L. Kimbell

The final 26 tables of this chapter, tables 14-39, extend and expand the statistical series on production that was started in the 1963 edition of the "Area Reports: International" volume of the "Minerals Yearbook" and that was subsequently updated and expanded in the 1965 and 1967-88 editions. In this year's edition, for the first time, a column has been added to each of these tables providing a 5 year average for 1985-89, inclusive. This should provide a clearer picture more rapidly of the role of each major producer over the 5-year period. The listing order of major producers, however, continues to be, as in past years, in descending order of rank in the year of review, 1989. With the inclusion of silver and uranium oxide in the 1988 edition of this chapter, this group of tables now includes each of the crude minerals that ranked from 1st to 19th in 1983 in terms of value of their output (as well as four others of lesser rank). These 23 crude mineral commodities accounted for 93% of the estimated value of world crude mineral of world crude mineral production in 1983. In addition, world output of five key down-stream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil are included because of their significance as products.

Jan 1, 1992

By E. C. Lane

[This is the eleventh in a series of reports on properties of commercial motor fuels made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R) Committee and the Bureau of Mines of the United States Department of the Interior. The first report contained data, on motor gasolines sold during the winter of 1935-36.3/ The present report presents analytical data for 2,020 samples, reprecenting the products of approximately 120 companies, which, as in previous surveys, include both large and small suppliers. In addition, the Pacific coast is represented by data averaged the Pacific Coast Technical Group before being submitted and' are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasoline each group has been averaged separately. The number of samples, items, and old brands comprising each group, exclusive of the of the Pacific coast, axe as follows: Regular price, 1,071 samples, 29 items, and 77 brands; premium price, 608 samples, 235 items, and 72 brands; third-grade gasoline, 341 samples, 196 items, 78 brands. The meanings of these terms as used in tae surveys are as follows:]

Jan 1, 1941