Search Documents

By O. C. Blade

Total sales of diesel fuel in the United States continue to Increase. This growth is due primarily to two causes: More conversion to diesel units by the rail-roads In recent years, and the greater use of diesel engines in trucks, busses, and tractors. Following are some figures on the distribution of the fuel computed from data issued by the Bureau of Mines.2/ [ ] Deliveries of diesel type fuel from refineries totaled 91,522,000 barrels during the first six months of 1955,3/ corresponding figure for 1954 was 91,170,000 barrels. Information on the properties of this engine fuel is very important to the petroleum industry, engine manufacturers, and consumers. To supply such information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of diesel fuel oil produced in refineries in this country.

Jan 1, 1955

By Michael M. Hamilton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine mineral resources and resource potential in and adjacent to the North fork Smith RARE II study area. Most mineral resources identified in this area are in laterites, highly-weathered residual soil zones. In the RARE II area, resources of nickel, cobalt, chromium, and magnesium were identified at 15 laterite properties and chromium resources at one chromite mine. Other commodities include copper, gold, silver, and mercury (fig. 1). Approximately 1,100 lode and 1,200 placer claims have been located in or adjacent to the area. Most placer claims are for literites. There are no patented claims or mineral leases. Forty laterite deposits on 15 ,properties within the RARE II area (fig. 2) contain about 16 million tons of identified marginal reserves and subeconomic resources containing nickel, cobalt, chromium, an magnesium (table 1). Most deposits have keen explored and are currently claimed. California Nickel Corporation is developing laterites on Gasguet Mountain, within and adjacent to the southeastern and western parts of the study area. If this project proceeds to production, a laterite processing plant on Gasquet Mountain would enhance the minability of other deposits in the study area. The Climax, PFM, DF, and Stone Corral properties (fig. 1, nos. 1, 6, 9, and 23) have deposits of sufficient tonnage and grade to attract mining interest; resources at these properties are in and adjacent to the RARE II area.

Jan 1, 1983

By G. St. J. Perrott, N. A. Tolch

"The measured strength of an explosive depends to a certain extent on which it is determined. An earlier investigation showed the relative propulsive strength of dynamites as determined in one type of apparatus, ballistic pendulum.4 The aim of this paper is to precept strength data on these same dynamites determined in another type of apparatus, the Trauzl lead block, and to compare the results with those of the ballistic pendulum. Trauzl lead block have been in use many years for the determination of thy strength of explosives, under moderate confinement.5 The common practice is to shoot 10 grams of explosive, in tinfoil wrapper,- and then to measure the volume of the cavity produced by the shot. The volume of the original borehole is deducted from the gross expansion and sometimes a correction is made for the expansion produced by the detonator. Dry sand is used for stemming the charge.It has been found that the expansion in Trauzl blocks is not strictly proportional to the charge. Naoum5 believed that for scientific accuracy the charge should undoubtedly be regulated to give the same average expansion for each sample tested, but for expansions of 200 to 400 cubic, centimeters the deviation from proportionality is not sufficient to give results appreciably in error.Neubner7 found that the proportionality curve is tangent to the charge-expansion curve at about 300 cubic centimeters expansion, provided that no deductions are made for the volume of the original borehole or the effect of the detonator; the total or gross expansion is proportional to the charge between expansions of 250 to 350 cubic centimeters without serious error."

Oct 1, 1930

By Oliver Bowles

Sandstone, a widely distributed siliceous sedimentary rock, is the third most popular building stone in the United States. It is formed by the breaking down of preexisting rocks by weathering, subsequent segregation of the detrital quartz grains into discrete deposits by the sorting action of water or wind, and finally cementation of the quartz sand into a coherent rock. The homogeneity and resistance to weathering of the resultant sandstone make it suitable for exterior construction. Its excellent wearing properties explain its popularity for flagging and stair treads. However, quarrying and dressing methods and costs are adversely affected by the abrasiveness and hardness of sandstone especially as compared to limestone.

Jan 1, 1963

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objective and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the following material is presented: (i) review of related literature, (ii) mathematical models to perform quantitative analyses of accident/ injury experience data using the tools and techniques of risk analysis, time series analysis, and the Markov process, and (iii) descriptions of the HDBSEL and ACIM programs which are used to perform accident/injury experience analyses and cost analyses, respectively.

Jan 1, 1993

By Walter R. Storms

"INTRODUCTION Geological examination of the Iron Mountain beryllium deposits was begun by a field part 3/ of the Federal Geological Survey in May 1942. Later in that month the occurrence was examined by the author and C. H. Johnson, of the Bureau of Mines, and a preliminary exploratory program was outlined. Trenching and sampling began about June 15 and were completed in July 1942. A large tonnage of beryllium-bearing material was indicate by this preliminary survey, so that additional funds wore allotted for further trenching and sampling, underground exploratory work, and diamond drilling. This later program was initiated in July 1942 and was completed in May 1943. 4/ACKNOWLEDGEMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilisation of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R.G, Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Mar 1, 1947

By Shirley F. Colby

A continued rise in construction activity in 1941 forecasts further increases in the demand for building materials of mineral origin, Recent studies by the Bureau of Mines, United States Department of the Interior, reveal that sales of mine and quarry products and their derivatives as a class have followed the long-term trend of construction activity in the past and are benefiting now by the upswing in all types of building. At present most building materials of mineral origin are holding their own in the competitive arena. A few are slipping behind, but others have forged fax ahead. Prominent among those that have surpassed general construction activity since 1925 are sand, gravel, and crushed stone (used in concrete and road metal and railroad ballast) and cement. Both building stone and roofing slate have followed the building curve closely, although in the last few years sales of roofing slate have risen above the curve and sales of building stone have dropped below it. Clay products and building lime, on the other hand, have lagged behind the general procession. Gypsum sales likewise dropped behind, but during the last few years, this industry, thanks to the wider acceptance of its newer products, has staged a marked recovery so that it now stands in about the same relation to total construction activity as it did is 1927-25.

Jan 1, 1941

By Stephen C. Tadolini, Thomas E. Marshall, Cecil Banta, L. J. Prosser, Anthony T. Iannacchione

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) endeavors to provide national and world leadership in the prevention of work-related illness, injury, and death. This is accomplished by using a scientific approach to gather information, assemble and create knowledge, then translate the knowledge and results into products and services. These products and services are then delivered to all personnel who can effect prevention. Obviously, the development and use of instruments to monitor mine roof conditions provides an opportunity to execute that mission. In the late 1990’s, based on observations at a number of underground limestone mines, only a few used roof monitors. Subsequently, NIOSH introduced the Roof Monitoring Safety System (RMSS) as an aid to roof inspection beyond traditional visual and sounding techniques. Initial expectations were that by gaining roof movement information, ultimately roof sag rates could provide indications of eventual failure. During this investigation, RMSSs were installed in 13 underground limestone mines in six states and this paper analyzes the data obtained at three of these mines. This paper also provides an overview of the system, data, analysis, and applications relevant to the RMSS.

By G. R. Hopkins

For several years prior to about the middle of 1928 both the number and capacity of natural-gasoline plants showed a steady increase; this resulted from a material gain in the supply of casinghead has due to the discovery of a number of flush fields with relatively high gas-oil ratios. From 1928 to date some form of proration has been continually in force, with a consequent curtailment in the supply of wet gas. This decline in available gas and a severe decrease in prices, due largely to the increasing competition of light refinery products, has eliminated virtually all of the weaker units during the last 5 years, with the result that the number of plants declined from 1,155 on January 1, 1928 to 19035 on January 1, 1930, to 909 on January 1, 1932, and then to 859 on January 1, 1934, The struggle of the small high-cost producers to exist is illustrated further by the trend in the number of shut-down plants, which has increased from 36 on January 1, 1930 to 100 on January 1, 1932 and to 128 on January 1, 1934. The increase in the number of plants prior to 1929 resulted in a material gain in the total capacity, but the decline in number between 1929 and 1932 was not followed by a corresponding decrease in capacity, as gains resulting from the construction of a few very large plants overbalanced the loss due to the dismantling of a large number of small ones. However, the low prices of 1932 and 1933 supplied little incentive for new construction, and the total capacity declined in approximately the same ratio as the number. Thus the total capacity declined from 11,387,000 gallons daily on January 1, 1932 to 13,060,000 gallons daily on January 1, 1934, Of the latter 9,181,000 gallons (91 percent) represented the capacity of the operating plants and 679,000 gallons (9 percent) the capacity of the idle plants.

Jan 1, 1934

The safety analysis of shaft-sinking operations included a review of accident reports from coal and metal-nonmetallic mine shaft-sinking projects in the United States, a review of foreign and domestic shaft laws, and discussions with shaft contractors and Federal mine inspectors. Accident data were studied to identify the most common and the most severe types of shaft accidents and to determine their immediate and contributing causes. Additional factors such as worker training and experience, equipment and sinking procedures, regulations and enforcement practices were also investigated to determine their impact on shaft safety. The results of the study are summarized in recommendations for improved training of shaft miners and clarification of Federal shaft-sinking regulations. A guide to assist mine inspectors in examining shaft-sinking projects is also included.

Jan 1, 1977

By C. R. Summers, J. N. Murphy

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneurnaric drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115 -dbA s rope drill to approximately 100 dbA.

Jan 1, 1974

By E. K. Stanek

This report contains the results of several related research efforts, all of which were aimed at enhancement of mine power system safety and reliability. The largest single effort was on optimum spares and maintenance scheduling for various components of a mine power system. Two closely related tasks involved calculation of the minimum arcing faults that could occur on dc trailing cables and the use of trippable load break switches to clear ground faults. Both of these tasks are concerned with reliable fault clearing to prevent shock and fire hazards. Three other closely related tasks were concerned with aspects of mine power system design: (1) alternate network topologies, (2) optimum voltage selection for mine power systems, and (3) selection of system components. The other research task consisted of laboratory tests to ascertain the effects of repetitive, low-level transients on insulation systems.

Jan 1, 1979

By F. Matanzo

This guide considers only nine of the many wire rope terminations used in the mining industry so use of the information presented for terminations not specifically addressed can be done, but with some risk. The nine terminations considered are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Aluminum Sleeve & Thimble, Thimble Splice with Four Tucks, V-Bolt Clip with Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The guide uses pull test data, axial fatigue test data, and data on sensitivity to poor workmanship, to rank the nine terminations with respect to these performance measures. A selection procedure is suggested and illustrated with an example. Failure data is used to identify the common modes of failure of each termination and so help the inspector direct his attention to the likely location for a failure and describe what he should be looking for. The data on which this guide is based is included so that as new data becomes available, the ranking order can be adjusted accordingly.

Jan 1, 1978

By J. L. Eakin

Systematic flooding was introduced into Nowata County, Okla., in May 1931. The results of this means of stimulating the nearly depleted Bartlesville reservoir in the county has been the subject of four Bureau of Mines Reports of Investigations.2-5/ This report presents a discussion of four full-scale water-flooding projects in the Delaware-Childers field and 1 pilot project in the Curl Creek field (fig. 1). All five plants have been in operation for only a few months. Although substantial increases in the rates of oil production have been obtained 1 by the injection of water, the projects are of particular interest at this time because of the novel methods of operation and new equipment that are being employed. One project utilizes a portable "package" plant designed for a pilot operation. All of the controls for this project are centrally located. The design makes it possible to remove the test plant to another location if the project is unsuccessful or if the unit is to be replaced by a larger plant. This project also utilizes diatomaceous-earth filters successfully for the first time and makes use of plastic pipe. Another novel feature of the operation is the aeration of Arbuckle limestone water through an airlift in the supply well.

Jan 1, 1955

By Kathleen M. Kowalski

In emergency management, the effects of stress on the performance of emergency personnel, typically have been ignored or regarded as too enigmatic to quantify. This paper discusses the concept of Critical Incident Stress in responders to emergencies. It presents the rationale for considering stress as a significant factor in the management of emergencies. It is proposed that Critical Incident Stress Debriefing in a disaster can improve the effectiveness of response teams on site, their turnaround time on site, and post-disaster time off the job. Critical Incident Stress intervention also can mitigate potential deleterious emotional effects associated with emergency work. This paper, prepared by a U.S. Bureau of Mines researcher, offers some ideas to the mining industry in general, to mine rescue team trainers, and to developers of program simulations on the specific issue of how people, time, materials and space may be factored into a plan for emergency management. The impact of stress on emergency workers is, presented as a missing component in present emergency management models.

By W. S. Sanner

This report describes the commercial application of the launder screen in anthracite-industry fine-coal cleaning operations. No new device, the launder screen has been used since the early part of the present century to size, screen, classify, and deslime the fine-anthracite sizes (Buckwheat Nos. 1 through 5) recovered by "river-coal" men dredging along streams draining the anthracite fields. The launder screen is stationary, has no moving parts, requires ample water for operation, and can be constructed economically on the job. Essentially, it consists of a wooden trough with baffles placed through its width to form a well system. The wells are covered by fine-mesh woven-wire screening. Each well is tapped with a number of orifices, and the hydraulic suction head developed in this manner removes high-gravity fines and slimes through the screening as underflow to waste. Material retained on the screen surface discharges as overflow product.

Jan 1, 1954

By M. A. Schellhardt

The Bureau of Mines has made periodic back-pressure tests on numerous gas wells in the Texas Panhandle field luring the past several years to study the delivery capacities of the wells under different pressure and operating conditions and to determine the relationships between pressures and rates of delivery from gas wells.4/ However, information regarding the intake capacities of gas-well systems is meager, end in projects involving- the flow of gas into porous-rock reservoirs it has been necessary to determine intake capacities of gas wells by trial. Accordingly the fundamental intake characteristics of natural-gas wells have been studied to develop a method for determining intake capacities under different wellhead pressures from data descriptive of the "output" or producing characteristic of the wells.

Jan 1, 1936

By Gregory M. Molinda

Extremely difficult ground conditions were encountered in the main belt entry in a room and pillar mine in West Virginia. Several generations of supplemental support, including cable bolts, cribbing, and Heintzmann jacks and beams failed to halt roof falls that threatened workers safety and the life of the mine. Polyurethane (PUR) was injected into 27 intersections in the roof and the results were monitored by borehole video camera. The mine had averaged 2-3 falls in the beltway per year and, since the roof injection, no roof falls have occurred. Pre- and post injection monitoring of test holes showed that stability can be achieved without filling all of the existing void spaces. Video logging showed that the project goal of building a beam from 2-6 ft into the roof was successful. Pre-injection monitoring of roof fractures uphole can delineate the zones to target for reinforcement, and avoid pumping PUR into large voids to little effect. Multiple-injection zones can be identified, and the entire intersection drill hole array can be optimized based on knowledge of the fractured zones. In addition, pre-monitoring can prevent excessive hydrofracturing in solid zones. Polyurethane injection is a proven method of rock stabilization in even the weakest, most broken ground. Optimization of the injection design by pre-injection video diagnostics can greatly contribute to the successful and efficient roof stabilization.

By F. R. Lee

When the Bureau of Mines was established in July 1910, one of the problems immediately attacked by the new organization was the development of standard, for the design and testing of electrical equipment that could be used without fear of initiating fires and explosions in underground coal mines. Research and investigation by Bureau personnel, supplemented by the published results of similar work by European mining authorities, led to the establishment of standards or "schedules." which guide manufacturers ill the design of many types of electrically operated machines and devices used in underground coal Mining. By issuing these standards, Bureau personnel establish the requirements to be met by such equipment before it tan be approved by the Bureau of Mines as permissible for use in gassy coal mines. Every 2 years the Bureau of Mines publishes a list of equipment that leas been accepted as approved or permissible during the preceding 2 calendar years. This is done to inform the mining industry of the availability y of the latest equip¬ment for safe use underground.

Jan 1, 1964

By Z. T. Bieniawski, Benjamín Celada

After emphasizing the importance of quantitative rock mass classifications in mining, originally directed to selection of rock support measures, but subsequently to estimates of rock mass properties such as rock mass strength and rock mass modulus of deformation, current attention calls for a classification specifically for rock mass excavability by tunnel boring machines (TBMs), which are used extensively in tunneling as well as in the mining industry. This paper introduces the Rock Mass Excavability (RME) index for predicting excavability of rock masses by TBMs using a quantification of machine performance and rock mass conditions. The RME index is based on five input parameters aimed at relating rock mass behavior and machine characteristics: (1) uniaxial compressive strength of the rock material, (2) drillability/abrasivity, (3) rock mass jointing at mine drift face, (4) standup time of the excavation, and (5) groundwater inflow. Development of the RME index entailed the collection of extensive data from more than 28 km of tunnels and some 400 case records from projects in Spain involving double-shield TBMs. In the process, a number of statistical correlations have been established between RME and such output parameters as degree of machine utilization, advance and penetration rates, thrust and torque of the cutterhead, and the specific energy of excavation. It was found that the RME index provides a particularly significant correlation for predicting the average rate of advance (m/day). In essence, the RME index is a classification system that features interaction of rock mass conditions with boring machine characteristics for use in the early stages of a project. It should be noted that the RME index does not replace the Rock Mass Rating (RMR) or Q-systems as used in mining and tunneling; indeed, one of the RME input parameters, standup time, is determined from the RMR. However, the approach presented introduces a specialized tool relevant to excavating tunnels and drifts. Possible applications to hard-rock mining are explored.

Jan 5, 2007