Search Documents

By Dale S. Preece, Ruilin Yang

Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidly attenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that the resulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of the explosive. The induced air blast reflects from the bottom of the borehole and this reflected pressure, even though doubled, is still approximately two orders of magnitude less than the detonation pressure. Air-shocks will ring back and forth in the air-deck for a few tens of milliseconds while the adjacent explosive column(s) are detonating. Transmission of the initial shock through the air along with reflections is an intensive energy consuming process. Energy balance results in shock heating of the air and a temperature increase. However, the increased temperature of the air is also orders of magnitude less than that of the explosive detonation products immediately behind the detonation front. Replacing high energy explosives with zero energy air-decks in a blasthole will always have a negative impact on the adjacent rock fragmentation and movement.

Jan 1, 2016

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor

Feb 1, 2020

By D. Preece

The mining and oil industry employs techniques such as geologic mapping, core drilling and electromagnetic and potential field techniques to explore for new deposits. Since new discoveries of major near-surface ore bodies are becoming progressively rare and since traditional exploration methods are unable to resolve ore bodies deeper than about 500m, high-resolution seismic reflection techniques show great potential for exploration to much greater depths down to almost 3km.

Jan 1, 2011

By Karl Ingmarsson

A model for drilling productivity and total drilling cost is presented. It specifically addresses down-thehole drilling, but also covers other drilling methods. The important factors are: 1, productivity in tons drilled; and 2, total cost per drill ton. For non-blasthole applications these factors are measured in drill feet and cost per foot. The model focuses on the entire system and allows the operator to optimize the system based on individual drilling conditions.

Jan 1, 1998

By E. Contestabile, B. von Rosen, P. Lightfoot

As part of an accident investigation ANFO was subjected to various abusive tests. A tractor-trailer carrying 18,000 kg of blasting explosives, caught fire, burned for approximately 30 minutes, and then detonated. A series of tests was designed to observe the behaviour of ANFO when subjected to different thermal stimulus tests and more specifically, the Height-to-Detonation Test. Three diameters of steel pipes were used in the Height-to-Detonation Tests thereby simulating cylindrical columns within a pile of ANFO. The ANFO samples were then subjected to various thermal stimuli to initiate a reaction. Through the use of some instrumentation, the response of large ANFO samples was recorded and its behaviour, including the occurrence of phase changes will be analysed.

Jan 1, 2001

By Erik Nygaard, Klaus Voges

ANFO is the most used industrial blasting agent in the world, and is often used as a reference for comparison of other explosives. It is known to work very well under dry conditions in large borehole diameters, whilst in small borehole diameters increasing amounts of toxic fumes (CO, NO and NOz) can be formed. In underground blasting, problems can also occur with reduced visibility caused by unreacted ammonium nitrate and overall composition of the detonation fumes. ANFO is made by mixing Ammonium Nitrate Porous Prills (AN-PP) and fuel oil. We have measured velocity of detonation (VOD), toxic fumes and visibility after blasting of ANFO in 54x2 mm steel tubes, and the differences are remarkable: By using an AN-PP grade developed for underground blasting and small diameters, the following can be obtained:

Jan 1, 2001

By Tom Short

The contract to drive twin 4,100 foot (1250.5m) long tunnels under the existing Cumberland Gap highway was awarded to a Joint Venture of S.A. Healy of Chicago, Illinois and Lodigiani USA of Fairfax, Virginia in January of 1991 under a $51.8 million bid. Due to very complex geological conditions, there were six distinct categories of excavation, the New Austrian Method of ground support was utilized throughout.

Jan 1, 1993

By Jorge Alvarez

In a large-scale open-pit mining operation, continuous efforts are made to control damage to the slope walls. An essential tool in this effort is determining the PPVc (critical peak particle velocity) in areas of interest. By knowing this value and generating criteria, drilling and blasting designs can be established to reduce vibrations that affect wall construction. It is crucial to understand that the PPVc changes as different mining phases develop, especially due to exploitation on the benches, which leads to vertical inherited damage. Therefore, it is imperative to regularly update the PPVc based on field tests that provide accurate data. With this information, vibration damage criteria can be established, and drilling and blasting techniques can be designed to minimize the impact on the remaining rock mass. This document presents a methodology for generating scaled criteria that best represent the reality of the rock mass.

Jan 21, 2025

By David Cheung, S. Paul Singh

"The characteristics of a blasted muck pile can have a significant effect on the productivity and economyof loading and hauling operations. Poorly fragmented and tight muck piles, caused by insufficientdisplacement of the broken rock, lead to higher digging and hauling costs. Therefore muck pile must be tailored to suit the loading and hauling equipment. In order to achieve this objective, it is imperative to understand the relevant muck pile characteristics and factors governing them. In general, muck pile characteristics are governed by the blast design parameters, rock mass geology, explosive characteristics and post-blasting requirements."

Jan 1, 2017

By Braden Schmidt

The following full paper will go into the products, techniques and people who work in the avalanche control industry giving insight to the other members of the ISEE an overview of the niche blasting that is Avalanche Control.

Feb 1, 2020

By Theodore C. Hile, Floyd P. Henry, Ken Gragg

"Conventional explosive-storage methods usually rely on combinations of earth and concrete barriers, along with sufficient distance between limited explosive loads, to avoid accidental conflagration. However, under many circumstances, Air National Guard (ANG) facilities co-located with civilian airfields have trouble meeting necessary Quantity-Distance (Q-D) requirements for Explosive Hazard Class/Division 1.1 and 1.4 materials. Because of the danger posed by explosives stored in earthcovered magazines (ECMs) too close to civilian activities, ANG units often find itdifftcult to maintain adequate stores of ordnance needed to meet unit mission goals."

Jan 1, 1999

By Karl Peterson, Bibhu Mohanty, Chanakya Nariseti

The mechanism of crack formation in two target rocks (Kuru granite and Flamboro Limestone) is studied experimentally by simulating the impact action of a percussive drilling bit. Rock samples are dynamically loaded using a custom made impacting bit (8 mm, 12 mm and 15 mm diameter bits). The target rocks are impacted at velocities 8, 10, and 12 m/s. The resulting crack patterns are visualized by three techniques, Dye penetration, CAT scans and Optical scans. Mapping of the crack patterns is manually done with Photoshop. For 3D damage visualization, the crack patterns are mapped in two planes (impact surface and longitudinal sections). The three techniques are compared to determine an optimum technique for better damage visualization. The evolution of crack pattern with impact velocity and bit diameter is discussed.

Jan 1, 2015

By Alan R. Gadberry

To resolve drilling and blasting problems, rather than treating symptoms and allowing problems to grow, the mine operator needs to change the way he operates. When a mine operator discovers a drilling and blasting result that he doesn't like, it is easy for him to think of that disappointing result as a problem. More often than not, however, that result is only a symptom of a problem, and the real, underlying problem cause can be seen when the operator looks in the mirror. Symptoms and problems relating to drilling and blasting are resolved when the mine operator makes appropriate changes in the way he manages his operations.

Jan 1, 1985

By K. M. Kim, J. B. Kemeny

A case study was conducted with 5 shots with varying pre-blast block sizes and explosive energies. From this case study a site-specific predictive fragmentation model was developed. There are two main innovations in this study. One is using an image analysis program (Split-Desktop 3.0) on the bench face to obtain the pre-blast block size (F80) quickly and consistently. Another innovation is to utilize the Schmidt Hammer Hardness (SHH) to estimate intact rock strength.

Jan 1, 2011

By Tom Paynter

In an underground mining environment, the primary method of firing a blast is using a combination of an electric detonator and a detonating cord to initiate the Nonelectric detonators. This method has been in use since the 1970’s. A firing line is used which can be subjected to damage and the need for constant testing and maintenance.

Jan 1, 2017

By Joshua Hofman, Braden Lusk, Erin Morris

Explosions in urban environments, whether of accidental or malicious cause, often result in extensive injuries, loss of life, and property damage. The ability to predict the damage inflicted by these events is highly sought after; in order to predict damage, the behavior of blast waves within these environments must be quantified and understood. Urban constructs such as buildings and roadway intersections affect the natural propagation of a blast wave, intensifying or rarefying the wave depending on their arrangement.

Jan 1, 2012

By Mick Fritz, Gregory Poole

Construction blasting is always challenging when in close proximity to existing structures, but when you are next to a landmark like Sanford Stadium at the University of Georgia it can get intense. Blasting on this project was performed less than 100 feet from students studying in their dorms at Reed Hall. Some shots are only a few feet from the columns on the stadium that hold up the sky boxes where meetings were being held while blasting was being performed. If a shot goes vertical the rocks would go through the floor of the sky boxes.

Jan 1, 2011

By R Malo, A Yetter

The use of large diameter blastholes for underground mining began approximately twelve years ago and are now routinely employed in a variety of ore types and stope designs. These large boreholes, ranging in size from 4 1/2 inch to 8 inch diameter, were first utilized in the same fashion as in open pit bench drilling. However, a variety of changes quickly followed in order to accommodate the unique conditions encountered while using a blasthole sloping method.

Jan 1, 1984

By Ulrich Leiste

If the iron ore loss is 15% in the process of mining, the total iron ore loss in the world will be about 461 million tons, this is equal to the total production of 230 iron ore mines each of which produces 2 million-tons of iron ore per year. Based on a series of blast tests in the Malmberget mine, this paper shows that ore recovery can be markedly increased by improving blasting technology such as choosing a correct primer position and making use of shock wave collision. The paper further suggests that a high ore recovery can not only reduce natural resource loss and mining cost but also prolong the life of a mine. In addition, the paper shows an example of reducing blast-caused rock damage in the roofs and walls of underground drifts (tunnels) by using new blasting methods in the Malmberget mine. Finally, the paper shows how the Malmberget mine has successfully reduced the ground vibrations, without adversely affecting fragmentation and ore recovery in sublevel caving mining.

Jan 1, 2014

Dear All, I am looking for information about vibrations and effects on fish in pools. A tunnel blast is planned to be carried out as close as 300 meters to a freshwater fish growing plant. What is the vibration criteria for fishes in pools? Your comments will be highly appreciated.

Jan 1, 2012